Search Documents

By Ginn Huh

The blasting work to construct a subway in Seoul, Korea have often caused increased neighbor’s complaints because of ground vibration. In order to prevent the damage to the structure, it was necessary to predict the level of blasting induced vibration and to determine the maximum charge weight per delay within an allowable vibration level. The effect of blasting pattern, rock strength and different explosives on the blast-induced ground vibration was studied to determine the maximum charge weight per delay within a given vibration level. The blasting vibration was measured from 10 sites along the subway line in Seoul and an empirical particle velocity equation from over 100 test data was obtained, V=K(D/W1’3 )-” , where the values for n and K are estimated to be 1.7 to 1 S and 48 to 138 respectively.

Jan 1, 2000

By Ann Barron, Paul Downing

Those employed in the explosives industry must have a keen familiarity of the explosives products they handle, the safety pro c e d u res they must follow, and the increasing number of laws and regulations governing blasting operations in order to perform their duties satisfactorily. For this reason, companies must make certain that their employees have the necessary knowledge and full understanding of their blasting and non-blasting responsibilities. Consequently, training is one of the most important elements in any company’s safety program.

Jan 1, 2004

By Thad M. Jones

This paper considers the sampling, digitizing and reconstruction of seismic signals. A sampling frequency range is proposed and a minimum limit is suggested. Digitizing precision criteria for both peak velocity and analysis applications are given. Several methods for reconstructing signals from sampled data are presented.

Jan 1, 1985

By Z X. Zhang

In sublevel caving mines, eyebrow break usually gives rise to lower ore recovery and worse safety in the field. Eyebrow break is caused mainly by two tensile stress waves: one from the front surface of a blasting ring, and the other from the roof of the drift. In order to reduce the two waves and finally to reduce eyebrow break at Malmberget mine, we employed two methods: (1) cartridge charge, and (2) double-primers in each blasthole. The two methods were tested in one ore body called ViRi. A total of 10 rings with the cartridge charge and 25 rings with the double-primers were blasted. At the same time a total of 34 ordinary rings were blasted in the same ore body. The result shows that the eyebrow break is 3.0 m for the ordinary rings, 2.3 m for the cartridge charge rings, and 2.1 m for the double-primer rings, respectively. In addition, the ore recovery for the double-primer rings is increased by 3% on the level of ViRi930, compared with that for the ordinary rings.

Jan 1, 2011

By James G. Stuart

For precise control and timing of a blast, people use electric detonators. Most of these contain a fine metal “bridgewire,” that heats to the required burning temperature when electric current passes through it. Users should be careful. Stray voltage can fire these detonators. Some designs are particularly susceptible to electrostatic-discharge (ESD). We will discuss some of the accidents we have encountered in our forensic work. We will recommend specific safe procedures for handling and firing these devices.

Jan 1, 2005

By Lyall Workman

New mines are frequently located at altitudes above 3,000 meters (10,000 ft.). Drill selection must take the altitude effects into account, to insure high productivity and good bit life. In particular, compressors must be sized differently than for low altitude operation. A larger compressor is required to deliver adequate air to the bottom of the blasthole. Many drills in remote locations use diesel engines as the prime mover. Altitude effects on engine performance should also be considered.

Jan 1, 2007

By Florian Bauer

The Fording River mine in British Columbia produces hard coking coal in an open pit operation. Coal seams are exposed by blasting overburden and digging blasted muck with rope shovels. The drilling and blasting process presents a considerable cost factor to the operation. Reducing the amount of explosives needed therefore contributes considerably to costs saving initiatives. However, reducing the powder factor only makes sense if the subsequent loading processes by the shovels are not compromised in terms of productivity.

Jan 1, 2014

By David E. Siskind

Increased mineral consumption and environmental concern have caused much interest in potential damage and annoyance from ground vibration and airblast produced by production blasting in surface mines and quarries. Ground vibrations are traditionally blamed for "shaking the house to its foundations," but often the airblast is responsible, particularly when the distances from mine to structure are large. Simultaneous measurements of ground vibrations, structure vibrations, and indoor and outdoor noise from blasting are being used by the Bureau of Mines to determine the relative importance of the ground and airborne blast energy in shaking the structure and making windows, dishes, etc., rattle.

Jan 1, 1977

By D Vrkljan, Z Ester

Excavating the building pit for the World Trade Center at Rijeka, it was necessary to blast over 160000 m3 of hard mass in fused condition. The building pit is located at a densely populated residential part of the main Croatian port Rijeka, close to the railway-track and traffic routes of the town. The permanent seismic monitoring points are foreseen on endangered housing and infrastructure facilities around the pit during designing and excavation of it. The seismic monitoring has been performed on 15 permanent points by occasion of over a hundred production and continuous blasting operations. The article considers the speeds of ground oscillations depending on applied maximum quantities of explosive charge according to fire degree, total quantities of explosives at the mine-field, structure of explosive charge, applied delay of mine boring and lines initiation mode and rock mass structure

Jan 1, 1999

By Corry Goumans

The job location is at Bear Lake Hydro Project located north of the town of Sechelt, British Columbia, Canada

Jan 1, 2013

By Victor Munoz, Jorge Oliva, Gonzalo Marias

Cerro Vanguardia is a known gold and silver deposit located in the province of Santa Cruz, Argentina. The mine has been in operation since 1998 and is thought to be one of the most important mines in Patagonia. More than 102 epithermal quartz veins have been identified in the area, with variable lengths, thicknesses, orientations and dips that constitute what is possibly one of the most extensive outcropping vein systems on earth.

Jan 1, 2019

By Tom Goforth, Rongmao Zhou

The interest of seismologists in mining explosions has increased substantially with the construction of the International Monitoring System (IMS). The IMS supports the Comprehensive Nuclear Test-Ban Treaty by providing global data coverage from seismic, hydro acoustic, infrasonic, and radionuclide sensors that will detect a host of natural and man-made events at regional (<2000 km) distances. Ideally, the recorded data can be used to identify those events that have explosive characteristics and therefore might be clandestine nuclear tests. The regional observations assure the detection of mining explosions, and these must be properly identified to avoid false alarms of the monitoring system. Cooperation with the mining industry, including documentation of the firing programs, provides critical information necessary to characterize the seismograms.

Jan 1, 2006

By Dan McCutchen, Oettmeier

Kelly bar drilling and blasting is unique to Florida, the' Bahamas and other marine limestone areas in the world where blast holes are required but will not remain open for the loading of explosives. This type of rock formation usually yields 1.5 tons of recoverable rock compared to 2.2 tons per cubic yard for competent limestone. The loss of .7 tons per cubic yard is due to voids and sand in the formation. These deposits all contain water to the top of the blast holes which are collared only a few ft. above the ground water level. The working pit is a water filled lake which is excavated from the bank by draglines. These drills have been used in Florida for many years to depths of 65 ft or less.

Jan 1, 1991

By Lindsay Wade, Peter Dare-Bryan

Benches in surface mines often contain known areas of ore and known areas of waste, which must be mined selectively. When rock is blasted it not only fragments but is also physically, and non-uniformly, moved. Risks therefore exist of ore being lost if treated as waste and of mill feed being diluted by waste. Both possibilities carry serious fmancial implications.

Jan 1, 2001

By Terry Matts, Bruce Ripley, Clark Fletcher, Paul Rapp, Stan Holtby, Jim Dent

The Stave Falls Project of BC Hydro, situated 65km east of Vancouver, BC, Canada, involved the construction of a new two-unit 9OMW hydro-electric facility to replace an existing powerhouse. The final phase of the intake excavation consisted of a plug blast to break the channel through into Stave Lake. The plug consisted of a rock and till wall topped with a fill cofferdam, about 51m wide and between 8 and 12m high. Total rock volume was approximately 2600m3, overlaid with about 4600m3 of till/fill. This paper describes the methodology and practical techniques used in planning and loading the blast, and the precautions taken to protect the new and existing structures and equipment. Blasting of the plug by the normal method using downholes would have required the placing of extra fill and much drilling through casing, so the contractor made the decision to drill horizontal holes from the dry, downstream side. Because of poor rock conditions, all 183 holes had to be drilled oversize at 3.5” dia. and fitted with 2.5” id. plastic pipes to keep them open. Hole lengths ranged from 2.5 to 18rn, with a pattern of 1.5m spacing and l.Om burden (with the holes slightly fanned vertically). Because of significant water exposure, a film-packaged emulsion explosive was used, placed using a pneumatic cartridge loader for maximum borehole compaction. The powder factor averaged 1.3kg/m3 (2.21bs/yd3, rock only). An initiation system of combination surface/downhole delay shocktube units was employed, with double and triple redundancy. The maximum number of holes firing in any 8ms window was limited to three (to minimize vibration), while the whole sequence was fully activated before the first hole fired. All shocktube connections were secured and covered over at the foot of the rockface before flooding the excavation downstream of the plug prior to the shot, To protect the powerhouse gates from hydraulic shock, all hole collars were grouted and an air curtain was provided. The blast was completely successful. A maximum vertical displacement of 6m was recorded, but no flyrock was evident. Readings for peak over-pressure and vibration were well below the allowed limits. Mucking proved to be easy, with fine fragmentation, full pull, and no tights.

Jan 1, 2000

By J Edmund Hay, Harry C. Verakisl, Richard J. Mainiero, John J. Mulhern

As the first stage in the rulemaking process, MSHA prepared requirements for the approval and use of permissible explosives and blasting items in underground coal mines. These draft requirements known as "preproposals" were announced in the Federal Register in mid-1984. The draft requirements on the use of explosives were written as a revision to Title 30, Code of Federal Regulations, Part 75, Subpart N. The draft requirements for approval of permissible explosives including sheathed explosives for unconfined applications, approval of water stemming bags, approval of detonators and approval of blasting machines were prepared as Parts 15, 16, 17 and 25 respectively.

Jan 1, 1985

By John Cowin, Dan McCutchen

Cowin & Company has specialized in underground construction since 1924. This paper reviews the sinking of two shafts in the Alabama coal fields using bulk-loaded explosives. Each shaft is eighteen hundred feet deep, and their diameters were twenty feet and twenty-three feet. The first consideration in changing to a new explosives system was safety. Safety began with the explosive supplier training the miners in the use of the new system, from explanation of the pumping unit on the surface to hands-on training in the shaft. The considerations covered include establishing a thunderstorm exit plan, and reducing exposure time of the crew to explosives while loading. The system consisted of a specialized pumping unit and an advance emulsion product. Eliminating the need for nitroglycerin based explosives, and reducing sensitivity to mechanical shock were goals that were met. Performance in the shaft and ease of use meant morale of the miners using the system remained high and positive. Performance benefits discussed include reducing the number of holes in the round, and cutting explosives loading time in half. Damage to the ribs of the shaft was greatly reduced, making it safer to work near the ribs on succeeding rounds. Cleaning the bottom before drilling the next round also showed marked improvement. The economics of the system became very apparent when cycle time saved was allocated against fixed cost of sinking these shafts.

Jan 1, 2000

By Frederick R. Cosgrave

Blasting near buried Natural Gas pipelines has always been an area of great concern. Given the many variables that the blaster must contend with in determining how to break the rock while trying to keep the vibration low and doing so while not compromising the pipeline.

Jan 1, 1995

By David R. Holberg

In the Kansas City metropolitan area, mineable Bethany Falls Limestone occurs 80 ft below river level under the 700 acre Park College Campus on the north bank of the Missouri River at Parkville. For 20 years prior to this project various firms passed over this opportunity to mine this property for construction aggregate because of uncertain costs, financial risk, and the difficulty of constructing an entry tunnel. This paper describes the drill and blast construction, rock bolting, and shotcrete lining of a 750 ft. long, 15% declining grade, truck tunnel through several Pennsylvanian limestones and shales.

Jan 1, 1997

By Robert C. Brown

During a research period lasting over three years, a vast number of seismograms were collected and analyzed. From this data, other than obtaining a host of new information pertaining to the effects of surface mine blast on underground mines, it was found that by mounting seismograph velocity transducers at the center of crosscuts in underground mines, seismograms can be obtained which give fairly accurate information about the maximum levels of vibration, and the associated Of stresses and strains, misfiring of blast holes, delay accuracy and delay overlap. The technique of analysis is a simple one; it involves matching of the frequency of wave or wave groups with the shot card information such as rows of holes, number of holes and the cumulative milliseconds of delays used in the blast holes. Any discrepancy that might exist between the frequency of waves and the expected cumulative millisecond delay for a given row or hole eventually will show up as a mismatch in the analysis. This simple technique enables the seismographer to be involved not only in the monitoring of blast peak vibration, but also in making recommendations as to the choice of millisecond delays, reducing the possibility of delay overlaps and reducing the hazards of blast hole cutoffs.

Jan 1, 1980