Search Documents

By Francisco A. Flores, José L. Aguirre, Héctor A. de la Fuente, Erika Bernal, Jorge Arroyo-Esquedla

This paper presents the analysis, design, and construction of soil improvement for storage tanks foundation support at a site in Tabasco, Mexico. A total of 980 Rammed Aggregate Piers of 12.5 m in length and 0.5 m in diameter were designed and constructed to support four storage tanks. The soil conditions at the site generally consist of loose to medium dense silty/clayey sand to about 8m depth, underlain by very loose to medium dense silty/clayey sand with seams of very soft clay. The use of Rammed Aggregate Piers induced densification of the soil to increase its stiffness and reduce the liquefaction potential to control both static and dynamic induced settlements. Standard Penetration Test (SPT) and Cone Penetration Test (CPTu) explorations were performed prior to and post soil improvement to compare the liquefaction potential and the Factors of Safety associated with the two conditions. Finally, the soil improvement installation rate is presented. Soil improvement using Rammed Aggregate Piers represented a suitable alternative to support storage tanks foundation in potentially liquefiable areas.

Oct 1, 2022

By Jewels Stover, Charles A. Luxford

Oklahoma City is undergoing a replacement program for an existing 66in (1.675m) water pipeline that conveys raw water from Atoka Reservoir to the City. This pipeline currently crosses the Canadian River on elevated piers and is subject to flood hazards. To replace the existing pipeline and mitigate flood damage concerns, two parallel microtunnels will be constructed below the river channel. Access is from construction shafts located near the midpoint of the tunnels; opposing drives are launched from each shaft. This geometry dictated shafts of significant depth – exceeding 120 ft. (37m). To accommodate the casing pipe segments and microtunneling machines, a minimum shaft diameter of approximately 34 ft. (10.4m) was required. Due to the difficult geologic setting, a reinforced secant pile compression ring is specified by contract in the top 70 ft. (21.3m) of these construction shafts to provide a very low permeability support system.

Sep 8, 2021

By Ke Yang

"Drilled shafts are typically used to support structures subjected to large moments at the shaft head. The large moment can produce push and pull forces on the two sides of a drilled shaft. Consequently, the applied moment is partially resisted by the push-pull moment resistance induced from the vertical side shears. This type of push-pull resistance has not been fully recognized in most design and analysis methods. In this paper, a 30 finite element model for a drilled shaft subjected to lateral load and moment is presented and is validated against two field lateral load tests. Based on the 30 finite element model, a parametric study is carried out. It shows that the push-pull moment can resist 18-35% of the applied moment. The parametric study also shows that the push-pull resistance varies linearly with loading eccentricity when the eccentricity is less than the shaft embedment length. A method to estimate the push-pull resistance is proposed based on the results of the parametric study. Then, a new method for lateral capacity prediction is proposed to account for the push-pull resistance. The base shear resistance is significant for short drilled shafts; therefore it is also included in the proposed method. A case study on four lateral load field tests illustrates that the new method could improve the accuracy of lateral capacity prediction when compared with the traditional Broms method.INTRODUCTIONDrilled shafts are typically used to support a variety of structures subjected to large moments. Sound walls, highway signs, traffic signals, high-rise buildings, electrical transmission towers, and bridge piers are examples of cases where lateral loads with large eccentricity would result in high overturning moments on foundations.Current analysis methods for capacity predictions (Broms, 1964a and 1964b; Brinch Hansen, 1961) or deflection predictions (Reese, et al. 197 4) of laterally loaded drilled shafts are based on the lateral resistance of soils and rocks. However, O'Neill pointed out that moments can be partially resisted through the push-pull resistance provided by the vertical side shears due to the rotation of the pile (Reese, 1997)."

Jan 1, 2005

By Nadir Ansari, Brian W. Wilson, Marina S. W. Li

"A hybrid shoring system consisting of cast-in-place soldier piles with Cutter Soil Mixing (CSM) infill panels was constructed for temporary support of a 19.8 m (65 ft) deep excavation in Vancouver, British Columbia, Canada. Deep Mixing (DM) was completed up to 9.7 m (32 ft) in fill, peat, wood waste and clayey silt with embedment in dense till, and soldier piles constructed through the dense till extending to below final excavation level. Two trial CSM panels were installed ahead of production to assist with developing the termination criteria of the CSM panels in the dense till. The constructed depth of the CSM panels was based on interpretation of real-time monitoring data obtained through the Bauer B-tronic system. Inclinometer monitoring data from two CSM panels and two soldier piles, as well as soldier pile survey target data was used to assess and monitor the performance of the hybrid shoring system throughout bulk excavation. The objectives of this paper are to provide an overview of the design and construction aspects of the hybrid DM shoring system and to present inclinometer and pile target data to demonstrate the lateral performance of the CSM infill panels and soldier piles. This paper also discusses the merits of using real-time monitoring data as part of the engineering decision-making process for validating CSM panel construction. BACKGROUND A hybrid DM shoring design was recently completed for a high-rise development in downtown Vancouver, British Columbia for temporary support of a five level basement excavation. Deep mixing was proposed by the excavation and shoring design-build team as the preferred method to construct infill panels between soldier piles because of the speed at which the shoring system could be constructed in variable fill, peat, wood waste and overburden compared with traditional secant piling methods. The development site is generally a truncated triangle in plan, with the longest side of the triangle being approximately 115.7 m (380 ft) long and the two shorter sides being approximately 71.6 m (235 ft) (Hybrid Shoring Wall 1) to 75.0 m (246 ft) (Hybrid Shoring Wall 2) long. The site is bounded by an existing bridge off-ramp structure along its longest side, and by city streets on the other two sides, as shown in Figure 1. The truncated section is approximately 16.8 m (55 ft) (Hybrid Shoring Wall 3) long. Due to project constraints, the hybrid DM and soldier pile shoring system was only proposed for the two shorter sides of the triangle and the truncated section. Traditional secant piles were installed for the longest side. This paper focusses on the hybrid shoring system. A typical detail showing the CSM infill panel with the soldier piles is presented in Figure 2."

Jan 1, 2017

By Zhitao Ma

The Cast-in-place Concrete thin-wall Pipe pile, referred to as PCC pile, is a new kind of pile for soft ground improvement. In this paper, firstly, the general introductions of the new pile technique, mainly including the technique principle, the structure of pile-driving machine, and the technological process were given, then based on the results of in-situ static lateral loading test, the pile lateral capacity, the relationship of load-deflection of pile at the ground surface, the lateral deflections versus depth and the soil reaction along the pile shaft were analyzed.

Jan 1, 2006

By Greg Plutko

Laboratory testing has shown that the Marsh Funnel test can be significantly impacted by long-chain polymer entanglement. In general, shorter hydration time leads to more chain entanglement which in-turn, leads to higher marsh funnel values that values seen for longer mixing. This trend makes it very difficult to predict funnel-viscosity on successive days. Data is presented which helps to explain this chain interaction effect on Marsh Funnel data and how it differs from traditional Fann viscosity. The data suggest that this long-chain polymer entanglement occurs more in samples with less hydration time and decreases as hydration time increases. There is also suggestion that higher polymer concentrations have a greater drop-off in marsh funnel viscosity for a given aging length than do lower solids slurries. Fann rheology was shown to be much less impacted by the hydration time of the PHPA polymers than was Marsh Funnel viscosity. This suggests that the Marsh Funnel viscosity is impacted by some aspect of the slurry that does not affect Fann rheology as strongly. It is known from literature that longer-chained polymers have more potential to entangle and our data support the theory that the Marsh funnel viscosity is greatly impacted by this polymer-chain ‘roping’ entanglement.

By Heinrich Majewski, Rob Jameson

"Careful review of site conditions and constraints is essential to select the appropriate shoring system for each project. Key evaluation criteria include the geotechnical profile, groundwater and environmental conditions, adjacent buildings and utilities, schedule and any project specific access or other constraints. Typical earth retention schemes range from rock or soil nail walls, through conventional anchored pile and lagging walls to deep internally braced cut-off systems. The Owner’s design team will often develop the conceptual approach under their design studies, and this is refined with Contractor input through Design-Build or Design-Bid-Build procurement. In downtown San Francisco, underground construction must accommodate a unique combination of variable fill, soil, rock and groundwater conditions, potential for severe seismic loadings, and constrained sites within a dense urban environment. The quarter square mile of San Francisco’s Transbay and Rincon Hill districts has seen repeated cycles of development, destruction and re-building through earthquakes and the economy, and has been intensely redeveloped over the last decade. Over 50 acres of this land has been reclaimed from the Bay since the Gold Rush and within 3 city blocks the bedrock slopes from over 250 FT depth below the fills up to outcrops over 100 FT above sea level. A series of project examples from within this small area illustrate how varied shoring systems have accommodated the highly variable subsurface conditions while offering best value in terms of cost, schedule and appropriate protection of adjacent facilities.INTRODUCTIONA walk of 3 blocks from Rincon Hill on San Francisco’s Harrison Street, north through the Transbay area to Mission Street will traverse an urban zone which has been reinvented twice within its 150 year history in response to major seismic events. This small area highlights the range of subsurface conditions and urban environments which are encountered and accommodated in shoring schemes throughout the city. This route down the north side of Rincon Hill overlies a steep bedrock slope, outcropping over 100 FT above sea level at its south end and dropping to over 250 FT below sea level at Mission Street. A complex overburden soil profile, shaped by seismic activity and changing sea-levels has created layered soils ranging from soft estuary muds, dense sandy strata and deep clay layers, in turn topped with urban fill, frequently contaminated with debris from the Great 1906 earthquake. This route runs parallel to, and 350 yards inland of, the San Francisco shoreline resulting in groundwater elevation close to sea level with almost limitless recharge within granular layers. On the higher slopes of Rincon Hill, groundwater is typically observed flowing on top of and periodically within the fractured bedrock formation. The Transbay and Rincon areas were developed early in the Gold Rush era of San Francisco. After destruction in the 1906 earthquake and fire, they became a transit gateway into the city throughout the 20th Century. Demolition of the Embarcadero Freeway in response to earthquake damage and social pressure has opened this large area to redevelopment within the last 20 years, creating a new commercial and residential hub for the city. In its latest wave of building, planners are developing taller structures with deeper basements, in turn creating new construction challenges. Selection of shoring systems appropriate for these developments requires detailed evaluation. The process must address both the rapid spatial changes in subsurface conditions and the constraints surrounding, and specific to, each site in order to define shoring performance requirements. This paper presents an overview of the subsurface conditions and land use development of the Transbay and Rincon Hill areas, with examples of the shoring systems selected to meet site-specific conditions and requirements. The projects cited range from soil nail wall"

Jan 1, 2017

By Hee-suk Yun, Dae-jin Hwang, Jeong-woo Seok, Myoung-mo Kim

"In this paper, the accuracy of the data measured by a newly developed displacement measuring system, DPRMs (Digital Pile Penetration and Rebound Monitoring system) and its applicability as a quality control tool were verified by field measurements of pile penetration and rebound for pile driving performed at 3 construction sites and 1 test site. The DPRMs data were found to be much better than handwork data. A new dynamic formula for pile capacities is proposed uses the results of a pilot dynamic load test and the final pile penetration. The ratios of pile capacities obtained by the new formula to those by the dynamic load test were 94%±7.4% in the contrast with 123±28.3% by the 5S formula and 68±24.0% by Hiley's formula. This result shows the superiority of the new formula. The ratios of the maximum compressive stresses calculated by using DPRMs to those calculated by using PDA (Pile Driving Analyzer) were about 90-110±10%. This result confirms the applicability of DPRMs as an overdriving monitoring tool. Two sets of DPRMs were used to measure the 3-D displacement behavior of a pile head at the test site. The more the pile head moves laterally, the less the final set values were expected because of the loss of driving energy, but this trend was not obvious within the limited data obtained at the test site.INTRODUCTIONPile construction monitoring consists of two parts. In the first part, enough capacity of the pile is secured to stand the design load. In the other part, pile damage during driving is prevented. Although several methods can be applied to achieve the first part, PDA is nearly the only tool for measuring pile stress.Several methods such as a static load test, a dynamic load test, an Osterberg cell, and numerous driving equations can determine the pile capacity. Among them, the static load test and the dynamic load test are most widely used. The static load test is advantageous because it has the highest reliability. The disadvantages are as follows: it is costly and time-consuming. Also, the capacity of the pile under construction cannot be evaluated. The dynamic load test has lower reliability than the static load test, but it is cheaper than the static load test, is reliable enough to determine the pile capacity, can evaluate the capacity of a pile during construction, and can offer information about construction conditions such as the pile integrity and the pi le stress during driving. The dynamic load test takes a relatively short time and is low cost compared with the static load test. However, it is still costly, time-consuming, and unnecessary to apply to all piles in the field as a construction measurement tool. Therefore, driving resistance (blowcounts) is commonly measured to confirm the pile capacity at construction sites."

Jan 1, 2005

By Edward Jacobsen, Patrick J. Lydon

"The ongoing expansion of the Oak Creek Power Plant in Oak Creek, Wisc., includes a tunnel bored in rock that connects to four vertical intake shafts approximately 1.5 miles (2.4 km) offshore in Lake Michigan. In 2004, Case Foundation Company was awarded a lump sum contract to install these intake shafts. In spite of delays that shortened the May to September construction season by up to 50%, four shafts and liner assemblies were drilled in 2005 and 2006. The shafts were connected to the tunnel in 2007 by mining upward to reach the lower portion of each liner and then removing its internal bulkheads so that lake water fl owed into the tunnel. The project is one of the largest private construction projects ever undertaken in Wisconsin. The expansion adds 1,230 megawatts of generation. In addition to the tunnel and offshore work, there will be 16 miles (26 km) of railroad track and 6 million cubic yards (4,600,000 m3) of earth work. The 27 ft (8.2 m) diameter tunnel, drilled some 150 ft (46 m) below the surface of Lake Michigan, originates onshore at a pump house. A structural slurry wall was constructed as the foundation for the pump house. The tunnel passes to the south near the current water intake before bearing east toward the new offshore intake shafts, which are 12 ft (3.6 m) diameter by 108 ft (33 m) long steel liner assemblies. These were grouted in place from approximately 3 ft (1 m) above the crown of the intake tunnel and then to 20 ft (6 m) below the lake bottom.Site GeologyOffshore. The plant site is north of the Racine-Milwaukee county line in an area affected by glacial activity. The soil conditions encountered at each shaft location were consistent, with noticeable variations occurring in the top of rock elevations that sloped downward from the innermost to the outermost shaft."

Jan 1, 2008

By Graeme Smart, Thomas Fiala

"Yorkville Plaza II, a 40-storey signature condominium residence, is scheduled to open on Avenue Road in Toronto’s prestigious Bloor-Yorkville neighbourhood in spring 2017. In close proximity to Toronto’s subway system, the new tower requires six levels of underground parking, founded in wet, silty sand.Isherwood Geostructural Engineers (Isherwood) was retained in April 2012 by developer Camrost-Felcorp to provide a shoring and excavation solution to address the challenging site conditions. A 31-storey upscale residential building under renovation with three levels of parking, owned by Camrost-Felcorp, flanks the site on the north. Situated on the eastern border is a 7-storey building with three levels of parking. Avenue Road, a four-lane arterial road that brings heavy commuter traffic into downtown Toronto, runs along the western border, and on the southern border of the site is a busy City road that brings traffic into the popular Yorkville area. The tunnel for the Toronto Transit Commission’s (TTC) overburdened east-west subway is located 14.5 m to the south, running below an existing 26-storey neighbouring building. Electrical and communication utilities (Bell) are closely located along the southern side. Non-documented existing excavation shoring, installed in the early 1970s, on the southern and western sides compounded the difficulties presented by the TTC tunnel.This paper presents the unique, non-conventional hybrid shoring solutions Isherwood developed to address the challenges presented by the site, as well as other complications that surfaced during the project: non-encroachment requirements (no tiebacks) beneath uncooperative neighbours, tight geometry to install shoring, and Toronto’s two coldest winters in decades.THE PROJECTBecause of circumstances associated with this site, for this project Isherwood designed two unique shoring walls which drew on their experience and expertise they had gained over the last 40 years. The following is the story of this site:Yorkville is an affluent neighbourhood in the heart of Toronto with a vibrant mix of high-rise towers, residential homes, tony restaurants and flagship shops. The development requires six levels of underground parking (a 20m deep excavation), with three levels undermining the high-rise buildings to the north and east and extending into wet, silty sand.Isherwood was retained in the spring of 2012 to design the excavation shoring. Isherwood’s scope also included field support, design, verification and monitoring. Finite Element Analysis was employed to confirm Isherwood’s design and anticipated movement of the south shoring wall and the TTC subway tunnel.The existing site was severed in two, with the proposed condominium tower slated for the southern portion. On the north half of the site stands a 31-storey building (Yorkville Plaza I at 21 Avenue Road), with three levels of underground parking, sitting on belled caissons which were one foot from the back of the proposed shoring wall so this would have to be considered in relation to the design and drilling methods. Constructed in the early 1970s, Yorkville Plaza I is currently being converted from the Four Seasons hotel to luxury condominiums by Camrost-Felcorp. To the east, directly adjacent to the proposed shoring, stands a 7-storey building (164 Cumberland Road) with three levels of parking, supported on spread footings founded on stiff clayey silt. The tunnel for the TTC’s busy east-west subway, a double box structure built by cut-and-cover in the 1960s, is located 14.5 m to the south, 9 m below grade, and running below an existing 26-storey building. Bell fibre optic communication cables and electrical lines, along with storm and sanitary sewers, are situated on the south and west sides of the site, leaving limited room to install shoring. Due to the heavy volume of commuter traffic on the four-lane arterial road (Avenue Road) to the west, site access and lane closure were not permitted here."

Jan 1, 2015

By Chris Harnan, Christophe Justino

The European Federation of Foundation Contractors (EFFC) and the Deep Foundations Institute (DFI) jointly published Edition 1 of the ‘EFFC/DFI Guide to Support Fluids for Deep Foundations’ in April 2019. This Guide was prepared by a Task Group comprising experts on deep foundations from contractors, materials suppliers, consultants and academics. The Guide builds on work carried out by the Tremie Concrete Guide Task Group and presented in Edition 2 of the Tremie Guide. The Paper discusses and describes the content of the Support Fluids Guide which presents the state of the art on support fluid management, as well as the R&D work currently being carried out and funded by EFFC and DFI sponsors through an ongoing Field Research Study (FRS) as well as a review of academic research linked to the EFFC/DFI joint effort aimed at improving knowledge and guidance on support fluids. The FRS and academic research will help to improve the understanding of relevant support fluid properties including stability of excavations, interface layer formation, effect of filter cake and the development of new sampling and testing methodology. The Paper also presents the initial findings from the FRS program as well as a discussion on the challenging aspects of support fluid management with emphasis on design, performance, testing, and the environment.

May 1, 2022

By Saieb Haddad, Henry Pate

"Building retaining walls in an urban area is becoming more diffi cult due to right-of-way restraints. Using standard concrete cantilever walls requires a construction easement behind the walls for installation, which for the most part is unavailable. To install these types of walls in a limited right-of-way requires extensive temporary walls to minimize the construction easement. Top-down construction walls utilizing tie-back anchors for support require either the purchase of the right-of-way or underground easements in the area of the anchors.These problems faced the Department on Interstate 75 widening in Knoxville, TN in an area of a large cut. A multi-story Insurance Building and a large commercial Retail Center were located at the top of the cut. To prevent any impact on the buildings, the walls had to be placed within a limited area. The option of buying the properties was prohibitively expensive. Due to the height of the two walls and the variability of the underling rock line, contiguous caisson pile cantilever walls were contemplated as the only wall type that would be appropriate. The cost of the two walls was estimated to be very close or even higher than the cost of purchasing the two buildings. The Department believed that there must be a better way to deal with the problem. A vertically tied-down pile frame wall constructed from the top-down with a concrete facing was developed. This allowed the construction of the walls to be restricted to the available limited area and provided substantial savings for the State. INTRODUCTIONThe widening of I-40/75 has been a major transportation project in the Knoxville area which is being constructed by the Tennessee Department of Transportation. The project includes 18 Retaining Walls and 13 Bridges. Two of the 18 Retaining Walls, refer to Figure 1, are to support two valuable properties, one being an insurance company housed in a multi-story offi ce building and the other a suburban shopping center which were appraised at $13.0 million and $5.0 million respectively. Due to the 31 ft. (9.5m) maximum height of each of the two Retaining Walls and the limited Right-of- Way of 15.0 feet (4.6m), a contiguous caisson pile cantilever wall was proposed for each of the two retaining wall sites with an estimated cost of $12.0 million each. The contiguous pile cantilever Wall is comprised of a line of caisson piles socketed into underlying competent bedrock. The design required that 4 ft. (1219mm) dia. piles be installed at 6 ft. (1.83m) centers, socketed into rock in order to provide lateral stability and restrict lateral wall movement to acceptable limits. The line of caissons would be fronted with a cast-in-place concrete face wall."

Jan 1, 2007

By Saieb Haddad, Henry Pate

"Building retaining walls in an urban area is becoming more difficult due to right-of-way restraints. Using standard concrete cantilever walls requires a construction easement behind the walls for installation, which for the most part is unavailable. To install these types of walls in a limited right-of-way requires extensive temporary walls to minimize the construction easement. Top-down construction walls utilizingtie-back anchors for support require either the purchase of the right-of-way or underground easements in the area of the anchors.These problems faced the Department on Interstate 75 widening in Knoxville, TN in an area of a large cut. A multi-story Insurance Building and a large commercial Retail Center were located at the top of the cut. To prevent any impact on the buildings, the walls had to be placed within a limited area. The option of buying the properties was prohibitively expensive. Due to the height of the two walls and the variability of the underling rock line, contiguous caisson pile cantilever walls were contemplated as the only wall type that would be appropriate. The cost of the two walls was estimated to be very close or even higher than the cost of purchasing the two buildings. The Department believed that there must be a better way to deal with the problem. A vertically tied-down pile frame wall constructed from the top-down with a concrete facing was developed. This allowed the construction of the walls to be restricted to the available limited area and provided substantial savings for the State.INTRODUCTIONThe widening of I-40/75 has been a major transportation project in the Knoxville area which is being constructed by the Tennessee Department of Transportation. The project includes 18 Retaining Walls and 13 Bridges.Two of the 18 Retaining Walls, refer to Figure 1, are to support two valuable properties, one being an insurance company housed in a multi-story office building and the other a suburban shopping center which were appraised at $13.0 million and $5.0 million respectively. Due to the 31 ft. (9.5m) maximum height of each of the two Retaining Walls and the limited Right-of- Way of 15.0 feet (4.6m), a contiguous caisson pile cantilever wall was proposed for each of the two retaining wall sites with an estimated cost of $12.0 million each. The contiguous pile cantilever Wall is comprised of a line of caisson piles socketed into underlying competent bedrock. The design required that 4 ft. (1219mm) dia. piles be installed at 6 ft. (1.83m) centers, socketed into rock in order to provide lateral stability and restrict lateral wall movement to acceptable limits. The line of caissons would be fronted with a cast-in-place concrete face wall"

Jan 1, 2007

This manual provides basic practical instruction on the inspection of driven piles. It covers the essential components of pile driving, such as the pile driving hammer, hammer accessories, the pile and soil, and frequently encountered test methods in an uncomplicated, yet knowledgeable, and practical manner. Insight is given into the methods of installing the foundation, dealing with the cranes which do the lifting, the hammers which do the driving, the leads that guide the hammer and pile, the compressors which provide the external power when required, and finally prevalent analysis tools and testing instrumentation and procedures which enable you, the Inspector, to do your job. This DFI Inspector's Manual for Pile Foundations will help the Pile Inspector who has limited knowledge of pile foundations. Perhaps this Inspector has been pressed into service at a moments notice; a few helpful hints and suggestions to him are desperately needed and he can look here for the basics. It is also useful for the experienced Pile Inspector as a reference guide. However, this manual is not a detailed check list of every possible scenario and detail which could ever be encountered. There are other sources available which give more detailed descriptions (and should be consulted by the Inspector when appropriate; a list of this additional reference material is provided and suggestions made in appropriate chapters of this text). The current manual is more a brief "textbook overview" with some of the more important aspects given at least some emphasis so that the Inspector has some direction and hopefully helps to produce a safe, yet economical, foundation.

Jan 1, 1997

By Yoshio Mitarai, Takeshi Nagatome, Yosuke Tanaka

"This paper describes an application of lightweight soil in a deep water area to stabilize an existing quay wall at the Port of Tokyo. Super Geo Material, abbreviated SGM, is a type of lightweight soil, which consists of dredged cohesive soil, cement and air foam, and is applied in coastal development work, such as port and airport construction. This paper reports a SGM construction project at the Port of Tokyo by using a SGM special plant vessel, which was deployed for the Tokyo International Airport (TIA) Expansion Project in order to achieve large-scale and rapid construction. The key issue in SGM construction is quality control. One key quality issue is control of the mix proportion of SGM in consideration of volumetric changes due to air foam-breaking during pumping and air foam shrinkage due to water pressure when SGM is placed in deep water. A smart technique for placing SGM is also necessary to prevent quality deterioration when SGM is placed in deep water, for example, increased bulk density and decreased shear strength due to water absorption. This paper introduces an actual case of SGM construction with a particular focus on quality control of SGM during construction.INTRODUCTIONSuper Geo Material, abbreviated SGM, is a lightweight stabilized soil which is used in coastal development work in Japan (CDIT 2008). SGM is applied as a backfilling material behind existing quaywalls or above underground structures in order to reduce earth pressure on the existing structure and improve seismic resistance. SGM has been applied in many coastal development projects. In particular, SGM was used at the Tokyo International Airport (TIA) Expansion Project (Haneda Airport) as the backfilling material at a quay wall at the joint between the reclaimed area and pier part in a new runway (Nagatome et al. 2010a & 2010b, Yamatoya et al. 2010, Mitarai et al. 2011). In this project, large-scale and rapid SGM construction was implemented by the special SGM plant vessels within 6 months under the condition of limited construction period.This paper introduces a new SGM construction project at the Port of Tokyo in 2011. This project employed the special SGM plant vessel, “Ryujin Mark II”, to achieve large-scale and rapid construction within a limited period. SGM was also placed in a deep water zone at the maximum water depth of approximately 15 m. Thus, quality control of SGM was a key issue for meeting project requirements. This paper describes the actual SGM construction in the Tokyo Bay area and quality control techniques for SGM, considering volume changes due to pumping and placement below water."

Jan 1, 2015

By Dr Karsten Galipp, Kai-Julian I. Hendler, Prof. Manuel G. Pinheiro, Dr Peter J. Bourne-Webb

With a share of approximately 11% of global greenhouse gas emissions, the construction industry contributes significantly towards climate change. This is why construction projects should not only be assessed on costs and technical solutions, but also on their carbon emissions. Life Cycle Assessment (LCA) is a tool which can quantify the environmental impacts of a construction project over its entire lifetime. The objective of this study was to determine the carbon footprint of three types of quay wall structures, namely sheet pile combi-walls, open piled decks and caissons using an LCA approach. Each of these quay walls were studied under the same boundary conditions, such as design life, ground conditions, dimensions, location and so on. The analysis showed that the sheet pile wall has the lowest carbon footprint whereas the open piled structure has the highest. Furthermore, it could be shown that the largest share of greenhouse gases (approximately 80%) is emitted during the production of construction materials. The transportation of materials and construction activities each contributed under 12% to total emissions. The sensitivity analysis showed that with innovative approaches, such as adapting the concrete mix design, the carbon footprint could be reduced by 26% to 40%.

May 1, 2022

By A. R. Dover

The Richmond San Rafael Bridge (Figure 1) is a 4.3 mile long major toll bridge span across northern San Francisco Bay. Tutor-Saliba/Koch/Tidewater (TSKT) conducted a comprehensive seismic retrofit, which was at the time Caltrans? largest-ever construction contract at $484 million. The robust foundation retrofit design of 11 bridge piers included the installation of 26 new, large diameter (126 to 162 inch OD, wall thickness 1.5 to 2.25 inches) CIDH and CISS piles, with steel pipe piles installed to tip elevations of Elev. ?140 to -220 ft, in water depths up to 70 feet. The open-ended steel pipe piles had initial sections ranging from 71 to 172 feet long, with full lengths that extended to the bay bottom and then through 100 to 130 feet of marine sediments to top of bedrock. The marine soils of most interest consisted mainly of soft to firm Young Bay Mud (YBM), a silty, moderately-sensitive clay common to SF Bay. A key constructability issue was the prediction of pipe piles ?running? under self weight (198 to 625 kips in air) and pile driving hammer weight (IHC S-500 with total assembly weight of 322 kips). The term "pile running" is used to describe the penetration of the pile into the soil due to the self-weight of the pile only. This issue was critical because 1) there was limited head room under the bridge deck, and 2) if piles run too deep, the pile splicing on several piles would be problematic (the lowest desirable pile top elevation after running was +10 ft). While running measurements are sometimes made during marine/nearshore construction, there is little published data on predicted vs. actual running. This paper discusses the running prediction under self weight for 26 piles, and the methodology used in developing the predictions, which ranged from 15 to 94 ft of penetration below mudline. Pile running was recorded and compared with predicted values. The prediction methodology was quite good, and no significant constructability problems were encountered. The authors ?tweaked? the model to provide a slightly improved prediction method. The paper presents the model, predictions, observations, and discusses important lessons learned.

Jan 1, 2006

By Terence Ma, Seok hyeon Chai, Jeff Lam, Thamer Yacoub, Brigid Cami, Sina Javankhoshdel

The Limit Equilibrium (LE) analysis of pile-supported geotechnical structures normally assumes a constant shear force for the pile instead of considering the non-linear capacity of the pile which is related to the pile displacement. In this study, a 3D Limit Equilibrium analysis is carried out for a landslide model supported with piles by considering the constant and non-linear capacity of the pile which is computed using a separate Finite Element (FE) algorithm. The depth of the pile, soil layering, and the pile properties are used with an assumed maximum displacement to compute the geotechnical non-linear capacity of the pile. In this study, the results of the initial unreinforced 3D LE model was first compared to the 3D FE analysis results. Then, the pile pattern was applied to the failure region in the 3D LE model, and then the factor of safety was recomputed. The results of the constant shear piles were compared to the model with the non-linear piles.

Sep 8, 2021

By Jim Slatter, Ben Collingwood

"It is well known that the adoption of an appropriate construction methodology is critical to quality outcomes for bored piles (drilled shafts). Many case studies have been published documenting quality issues that have arisen due to a range of causes involving ground conditions, ground support, drilling and cleaning techniques, groundwater, concrete properties and concreting methods, amongst other things. Despite the body of published information, pile defects remain common in practice. The authors share over 40 years’ experience in the Australian piling industry and have participated in many hundreds of projects involving bored piles in design, construction and testing roles. It is the authors’ experience that many defects are caused by conditions or practices that are known to be problematic, but that are often not recognised or addressed at the time of the works. This paper provides an overview of industry practices and key factors relevant to quality outcomes. The authors draw upon their own construction experience, published case studies and guidelines, and observations from independent pile testing activities they have been involved in across the Australian piling industry. The intent of the paper is to provide a consolidated review of typical industry practices and to highlight key areas in which construction quality can be enhanced.INTRODUCTIONThere are many published studies of cases where bored piles have been constructed and found to have concrete defects. The authors have had personal involvement in many cases where the outcomes and learnings are not publically available. The nature and cause of defects is always dependent on site and project specific factors, and therefore methodologies and materials that produce satisfactory outcomes in certain circumstances may be problematic elsewhere. The process of bored pile construction encompasses the following key areas:??excavation and ground support;??pile preparation and cleaning;??pile reinforcement and fitments.??concrete supply and mix performance;??concrete placement methodology;Each of these elements is equally important and can influence construction quality in completed piles. In the authors’ experience, it is often a combination of seemingly minor issues that leads to significant defects in piles. Conversely, attention to detail in all aspects of bored pile construction is required to produce outcomes of a consistently high standard."

Jan 1, 1900

By Monique Nykamp

"INTRODUCTIONTerminal 46 is located just south of downtown Seattle, and is one of the Port of Seattle’s busiest container terminals. The Terminal 46 Redevelopment Project was undertaken to replace the existing 15-m-wide (50 ft) cranes along the apron with 30-m-wide (100 ft) cranes, which can unload larger, post- Panamax ships. The project included upgrading the existing waterside crane rail with new piles and constructing a new land-side rail behind the sheetpile bulkhead. The new piles had to be installed adjacent to the existing apron without causing damage, which was a signifi cant geotechnical challenge due to the soft soil conditions at the site. An instrumentation program performed during the test pile program evaluated this challenge and allowed for the development of specifi c production pile installation procedures that had the least possible effect on construction costs and schedule. SITE HISTORYThe site lies along the west side of Elliott Bay, north of the mouth of the Duwamish Waterway. Prior to development, this area was part of the tide fl ats where the Duwamish River drained into Elliott Bay. Prior to 1970, there were several existing timber piers and structures in the area. In the 1970s, the Port of Seattle constructed a 900-m-long (3,000 ft), 30- m-wide (100 ft) apron to support fi ve, 15-m-wide (50 ft) container cranes. The contained backland area was then fi lled with dredged spoils (sand and silt with organics) and the upper 5 to 20 m (16 to 65 ft) backfi lled with sand and gravel.The existing apron was constructed using 0.4 m (16 in) octagonal prestressed concrete piles to support the precast concrete deck and crane rails. The pile-supported bents were spaced at 6.1 m (20 ft), center-to-center, along the longitudinal direction. Pile lengths typically varied from about 20 to 40 m (65 to 130 ft) with 15 to 26 m penetration below mudline (50 to 85 ft penetration). The slope below the apron was constructed at about 1.75 horizontal to 1 vertical to allow for suffi cient water depth for cargo ships. In most areas, a riprap buttress was placed at the toe of the slope. A typical cross section of the apron is shown on Figure 2.Several stability, settlement and pile driving issues arose during the original construction of T-46 (Pita, 1983). Reportedly, movement of the submarine slope occurred during pile driving, resulting in settlement behind the bulkhead. Pile driving reportedly caused settlement of adjacent piles. In addition, some piles were “running” (dropping quickly under one hammer blow) during installation."

Jan 1, 2007