Search Documents

By Anne Lemnitzer

Full-Scale cyclic field testing was performed on a 3x3 pile group consisting of nine cast-in-drilled-hole (CIDH) reinforced concrete shafts and a comparable single-shaft in order to investigate group interaction effects. Both specimens were constructed with pile diameters of d = 0.61m (2 ft), fixed head boundary conditions, and placed in stiff clayey soil at a test site near the LAX Airport in Southern California. Internal instrumentation was installed in the single pile as well as in three piles within the pile group to obtain pile curvatures. External instrumentation controlled the lateral displacement of the specimens. A combination of experimentally and analytically obtained p-y curves for the single pile was used to simulate results for piles located in the group when field data were not available. All test specimens were tested to structural failure and excavated after test completion to investigate pile damage and plastic hinge formations. Calculated group interaction factors ranged between 1.0 at very small displacement levels of <2.5 mm (0.1 in), 0.8 at the initiation of the pile-soil-pile interaction, i.e. between 4 mm - 15 mm (0.16-0.6 in), and increased towards 0.9 near structural failure (displacement >25 mm or 1 in). A literature set of p-multipliers was found to reproduce an accurate fit to the available load displacement test data from the group.

Jan 1, 2010

Jan 1, 2001

Jan 1, 2002

By Walter E. Vanderpool

Three drilled foundations for an elevated water-tank were instrumented, tested and monitored during construction and the first two years in service. One shaft was load tested by the Osterberg method. A void was detected in one shaft by cross-hole sonic logging, pulse-echo logging and concrete coring. The void was instrumented, hydrostatically tested and pressure grouted. The shaft was ?abandoned? and replaced by two smaller shafts with a straddle beam cap. One of the replacement shafts and the cap were instrumented. The strain that appeared in the abandoned shaft, the replacement shaft and the cap were monitored during the remainder of the construction, through the commissioning test and the first two years of service. The results demonstrate the precision and sensitivity of the vibrating wire strain gage.

Jan 1, 2004

By W. G. K. Fleming

The general history of piling is traced up to the present time with regard to the evolution of methods and materials. The processes have been strongly influenced by developments in basic equipment and industrial change. It is noticeable that in the twentieth century more progress has taken place than in the many previous centuries. It has been strongly influenced by the general development of Soil Mechanics. Test loading is probably the most effective way to assess the success of designs and many empirical relationships have been challenged through it. As we approach a new century it appears that it will be an age of rapid equipment development, with much enhancement of understanding of what has been done. Processes of automatic construction and testing will becoming commonplace. These changes will narrow the limits of conventional scatter that have come to be accepted and to a large extent will be driven by political efforts to curtail energy consumption, to raise standards of quality and reliability, and to conserve the environment. 1. Ancient history. Piling is an ancient art. Its first mention in history is from Herodotus, the first person to commit an account of his times to the written word in the years 557 to 479 BC. He evidently had a strong interest in engineering matters because he wrote of building, brick making, reinforced brickwork, river training, canal building, bridge construction, tunnelling and its acoustic detection and piling. The piling reference comes from Book 5 at paragraph 16.

Jan 1, 1999

Jan 1, 2005

By Robert Thurner

The underground car park "Admonterhof in the historical centre of Graz is an example for the technical and economical success of a complicated structural design using a concept on the basis of the observational method. The intention to built a 20 m deep excavation beneath a protected monument was accompanied by some essential issues: the preservation of the existing state avoiding extensive displacements by means of a girder grid of reinforced concrete, its support on large bored piles and small steel-tube piles with possible active compensation of differential settlements, the excavation support in none built-up areas with secant bored piles, the underpinning of existing buildings with different structures by means of jet grouting. Furthermore the hydraulic gradient and the permeability of a rock formation in a part of the excavation had to be explored with the purpose to control the inflow of groundwater with a level difference of more than 10 m.

Jan 1, 2006

Jan 1, 1984

By David L. Borusiewicz, M. Suri Surendra

"Abstract Helical piles have been used as anchors and for supporting lightly loaded structures as a method of underpinning, etc in the past. Recently, helical piles are being used to support new structures because of their simple installation process using relatively light and mobile equipment. This paper presents the results of evaluation and design performed for the temporary support of existing piers during a bridge rehabilitation project.INTRODUCTIONThe helical screw foundation was invented and patented by Alexander Mitchell in England in 1833. He installed screw piles to support lighthouses in the tidal basins of England. Many applications in the earlier years in the USA were in North Carolina and in Florida to support lighthouses (in coastal plain deposits). A lighthouse of similar foundation design is still in use at Key Biscayne, Florida.In the USA, the helical piles were reintroduced as foundation elements for electrical transmission towers. Helical piles were also used for anchoring guys of self supported towers and as tie-backs for excavation support systems. Typically, helical piles are being used for supporting lightly loaded buildings and for underpinning buildings undergoing distress as a means of remediation. The helical piles are not commonly used in the transportation industry.HELICAL PILESHelical pile is a segmented deep foundation system with helical bearing plates welded to a central steel shaft. Load is transferred from the shaft to the soil through these bearing plates. Central steel shafts are available in either a square shaft (Type SS) or a round shaft (Type RS). The Type SS series are available in 38 mm to 57 mm square sizes. The Type RS series are available in 73 mm to 114 mm diameter sizes. Type SS-RS combinations are also available for compression applications in soil conditions where dense/hard soils must be penetrated with softer/loose soils above the bearing strata.The leading segment consists of a shaft with one or more helical plates that are welded to the shaft. The plates vary in diameter from 203 mm to 355.5 mm and have a thickness of 9.5 mm or 13.7 mm. Typically the plate diameter increases from the bottom of the shaft upward. A helical bearing plate or helix is one pitch of a screw thread. All helices, regardless of their diameter, have a standard 76 mm pitch. Being a true helical shape, the helices do not auger into the soil but rather screw into it with minimal soil disturbance. Helical plates are generally spaced a distance of two to three times the diameter of the plate directly below in order for them to function independently as individual bearing elements. A typical detail of helical pile is shown on Figure 1."

Jan 1, 2014

By Kenneth Pidgeon

The Boston Marine Industrial Park (BMIP) Boat Section, which is part of contract C04A2 of the Central Artery/Tunnel (CA/T) project, is currently under construction in South Boston, Massachusetts (Fig. 1). The Boat Section is approximately 900 feet long and varies in width from about 135 to 185 feet (Fig. 2). The depth to the top of the Boat Section base slab varies from about 28 to 31 feet below final ground surface and about 23 to 26 feet below normal ground water levels. The Boat Section is supported on 578 anchors drilled into the underlying bedrock each designed for a working load of 630 kips. Design and Construction Team The owner of the project is the Massachusetts Highway Department (MHD). The owner&apos;s representative is the Management Consultant, Bechtel/Parsons Brinckerhoff. The section design consultant (SDC) consisted of HDR Engineering, Inc. with GEI Consultants, Inc. as the geotechnical subconsultant. The general contractor was the joint venture of Kiewit, Perini, Atkinson, and Cashman. The boat anchors were installed by the subcontractor Delta Geotechnical Services, Inc.

Jan 1, 1994

By Samuel J. Kosa

The Monotube is a uniformly tapered high-strength steel shell pile manufactured for friction pile applications. The Monotube pile was developed in the early 1920&apos;s in Canton, Ohio. Its first commercial installation was an Ohio railroad trestle in 1926. The Monotube has been manufactured in the same Canton plant since its inception. The Monotube is produced in four diameters, 12, 14, 16 and 18 inches, with U. S. Standard Gage wall thicknesses of 9, 7, 5 and 3. The uniformly tapered Monotube section can be manufactured in one of three rates of taper.

Jan 1, 1993

By Nuno Cruz

"The concrete overbreak estimation for bored piles provides the quantification of the shaft’s expansion beyond its theoretical volume. There are stability analysis methods that can be employed before and after concrete pour but as for the moment of decision, during pile cast, the most common method still consists in measuring the rising of the concrete level in order to compare its poured volume with the theoretical pile section volume. This is a determinant parameter to monitor, not only because it assesses the bored shaft stability but also because it represents a direct cost. When analyzing the estimation methods commonly applied on-site it becomes evident that these are often affected by human errors that lead to misleading results. The objective of this paper is to identify those errors and discuss a subject which is usually overlooked. As a general conclusion, it was ascertained that most errors derive from inaccurate volumetric data, working procedures and gauging equipment. By acknowledging these widespread practices deep foundations contractors will be in a better position to make informed decisions on how to correct and improve bored pile stability.GENERALBackgroundWhen executing bored piles, the estimation of its concrete overbreak allows a swift appraisal of the excavation stability during the drilling process. This is simply obtained from the proportion of the poured volume of concrete over the drilled shaft theoretical volume, as shown in equation [1].Where CO = concrete overbreak percentage, Vc = volume of poured concrete, Vr = pile’s theoretical volume. This calculation not only provides a general idea of the shaft’s expansion from its theoretical volume, but also the outline of the excavated column’s geometry. For the latter, the outline will be as accurate as the number of measurements taken for each partial known volume of poured concrete. This means that for each load placed inside the excavation there is a corresponding rising of the concrete level. The profile of the definite pile is then plotted (see Fig. 1) and allows inferring about how stable remained the shaft walls up to the moment of casting.The technological developments in this area have provided other methods for determining pile stability before and after pile cast, such as ultrasonic echo sensing, cross-hole sonic logging or thermal integrity profiling systems. Notwithstanding, concrete overbreak assessment remains as common practice and confers the advantage of providing stability information during the process of pile casting."

Jan 1, 2017

Jan 1, 1997

By Mary C. Nodine, Michael P. Walker, Paul Eggers, Donald E. Aubrecht

The CANALSIDE commercial development in Buffalo, New York serves to revitalize the former site of the Buffalo Memorial Auditorium, adjacent to Lake Erie. The Auditorium was constructed in 1940 and founded on steel H-piles driven to limestone bedrock. After decades of professional sport and entertainment events, the “Aud,” as it was locally known, was closed in 1996. It sat vacant until it was demolished in 2009, at which time plans were made to revitalize the area with shops, restaurants, and a historic replica canal. The only portion of the Aud that was left intact was a subbasement boiler room. The subbasement was renovated in 2014 and has since been used to house water and ice making equipment for the historic replica canals, which boast recreational ice skating in the winter. The subbasement floor was about 10 feet below groundwater and the Lake Erie water level. The floor consisted of an approximately 4-foot-thick layered inverted waffle slab system, with reinforced concrete grade beams and concrete infill between the grade beams. A waterproofing membrane was located near the base of the slab. There were no major seepage issues in the subbasement, so the existing waterproofing membrane was assumed to be intact and performing adequately. A four-story building housing a children’s museum was proposed to be constructed directly above the subbasement. The loads imparted by the new building would exceed the capacity of the existing piles, so it was determined that drilling micropiles through the subbasement floor would be the most practical means of supporting the new building. Drilling through the existing slab and waterproofing system was a concern due to the challenges of controlling water during construction and the importance of maintaining the integrity of the permanent waterproofing system.

Jan 1, 2018

Jan 1, 2001

Jan 1, 1998

By Jesús E. Gómez

This work is a continuation of a paper presented in the 32nd DFI Annual Conference, Colorado 2007, titled ?Hollow Core Bar Micropiles - Design parameters interpreted from 260 load tests.? The first paper presented the results of the verification and proof tests performed for the retrofit of two bridges with hollow core bars that used 260 micropiles. It included an interpretation of the unit bond values in the different soils where micropiles were installed. Recently two additional bridges within the same geological environment were also retrofitted using 144 hollow core micropiles. This paper includes the interpretation of the additional data from the proof tests performed and refines recommended values for design of hollow core bar micropiles in soils similar to those encountered in these two projects. The authors believe that the data collected will significantly add to the relatively small existing database on micropile tests and may also be useful during implementation of the LRFD design methodology.

Jan 1, 2008

By Alan J. Lutenegger

Some years ago, a method was developed to incorporate a grout column around square-shaft helical screw-piles and anchors to increase shaft buckling resistance under compression loading. An additional benefit of this grouted shaft is to increase the load capacity in both compression and tension, depending on the geometry of the lead helical section and the soil conditions. Because of the unique construction procedure, the contribution of the shaft to the total capacity has largely been unknown. The behavior of grouted shaft helical anchors in clay was investigated by performing full-scale axial uplift (tension) load tests on a series of anchors installed at the University of Massachusetts Geotechnical Test Site. In order to isolate the contribution of the grouted shaft to the total load capacity, anchors were installed with a wooden dowel connection between the lead helical section and extension sections on three of the four anchors so that only the shaft resistance would be measured during the load tests. The grouted shafts ranged in length from 10 to 30 ft (3 to 9 m). Initial tests were performed approximately 5½ months after installation. Nearly four years after the initial tests were performed, the tests were repeated to evaluate any significant change in capacity with time and/or repeat testing (preshearing). The soil conditions at the site are presented along with the load-displacement curves for both the initial and repeat teats and a discussion of the analysis of the results. Repeat load tests showed an increase in capacity from the initial testing, however the percent increase was not the same for all depths. The results demonstrate that considerable shaft resistance can be developed in clays from the grouted shafts as might be expected. Depending on the L/D ratio of the shaft and the contribution of the lead helical section, at working loads the shaft capacity can dominate the behavior.

Jan 1, 2011

By Jorge Beim

Helical Piles are increasingly being used to support and rehabilitate structures subjected to compressive axial loads. Traditionally, empirical correlations between installation torque and load capacity of helical screw piles are used as the field quality control. Load tests, however, are always recommended to validate the installation process and design methodology. This paper describes a test program performed on helical piles installed at the National Geotechnical Experimentation Site of the University of Massachusetts - Amherst campus (UMass-Amherst), well known for its deep varved clay deposit. Seven of these piles were submitted to Dynamic Load Tests using the Pile Driving Analyzer® (PDA), and also to Static Load Tests. Good agreements were obtained between the results of the dynamic and static load tests, encouraging the use of the former testing method as a viable alternative to the latter for determining the compressive load capacity of helical piles installed in cohesive soils. The results of the load tests were also compared to the predictions based on torque correlations, resulting in correlation coefficients which were higher than the ones traditionally used.

Jan 1, 2012

By James A. Schneider

The evolution of the American Petroleum Institute (API) design method for axial capacity of driven piles in siliceous sands is explored, and complemented with an overview of how changes in offshore site investigation practice have increased the level of knowledge with respect to vertical variability of soil characteristics. Increased use of the cone penetration test (CPT) provides near continuous profiles of soil type and strength which can be used in calculation methods that address variation in local shaft friction rather than the API method which seems to have initially been based on observations of average shaft friction in relatively uniform sand deposits. Development of a formulation for CPT correlations to axial pile capacity in sand is discussed, along with implications to existing factors of safety used in routine design.

Jan 1, 2006