Search Documents

By Diankun Lu, Ganfeng Tu, Edouard Asselin, Feng Xie

A novel separation process for detoxifying cadmium-containing residues arising from zinc hydrometallurgical processes has been developed. An initial investigation indicated that a high concentration of zinc in the sulfate solution can be effectively separated from cadmium by solvent extraction with P204 (di(2-ethylhexly)phosphoric acid, D2EHPA). The mixture of sulfuric acid and ammonium citrate ((NH4)3C6H5O7) is thus used to extract metals from the residue at room temperature. Copper in the leachate is recovered by solvent extraction (SX) with LIX 973. Cobalt in the raffinate from the copper SX process is recovered by precipitation with a-nitroso-ß-naphthol. The results show that more than 50% of the copper and virtually all the zinc, cadmium and cobalt in the residue can be leached under the experimental conditions used here. Virtually all dissolved copper and cobalt can be recovered in the subsequent solvent extraction and precipitation processes. The presence of (NH4)3C6H5O7 could significantly facilitate the extraction of zinc by D2EHPA in the subsequent separation of zinc and cadmium. More than 97% of the dissolved zinc can be recovered through a two-stage counter current solvent extraction process. After separating copper, cobalt and zinc, cadmium can easily be recovered from the solution either by cementation with zinc powder or by electrowinning, while the purified solution can be recycled back to the leaching process.

Jan 1, 2014

By M. Kumral, E. Dilhuydy, B. Ozdemir

"In-pit crushing and conveyor (IPCC) systems have become increasingly popular in the mining industry as an alternative to truck-and-shovel systems. Deciding whether to haul waste rock by truck or IPCC represents an important gap to be investigated in semi-mobile IPCC systems. A cost analysis is presented to evaluate the feasibility of crushing and conveying waste material in IPCC systems, along with sensitivity and risk assessments through Monte Carlo simulation. Although the capital expenditure is higher, results showed waste crushing will be feasible in deep pits and over long mine life and haul distances.RÉSUMÉ La popularité des systèmes de concassage et de transport dans la fosse minière (IPCC, de l’anglais In-pit crushing and conveyor) n’a cessé de croître dans l’industrie minière ; ils constituent en effet une option intéressante de remplacement des systèmes par camions et pelles mécaniques. Le choix entre le transport des stériles par camions ou par IPCC est encore difficile à faire et devra faire l’objet d’une étude approfondie au niveau des systèmes d’IPCC semi-mobiles. Une analyse des coûts est présentée pour évaluer la faisabilité du concassage et du transport des stériles par les systèmes d’IPCC, de même que des évaluations de la sensibilité et des risques par le biais de la simulation de Monte Carlo. Si les dépenses en immobilisations s’avèrent être plus élevées, les résultats ont cependant montré que le concassage des stériles sera envisageable dans des fosses profondes ainsi que sur une longue durée de vie et de longues distances de transport. INTRODUCTIONThe mining industry is currently facing many challenges such as low commodity prices, increasing environmental concerns and regulations, lower grades, deeper mines, and greater waste-rock quantities. As a result, the profitability of mining operations has decreased, with many mines stopping or suspending operations, and many new projects being postponed. Mining companies have therefore focused on improvements and innovations to increase the cost effectiveness of operations, for example, increasing production capacity to take advantage of the economies of scale (Crowson, 2003) and decreasing the unit operation cost. Changes in production capacity force mining companies to evaluate alternative material handling systems.During the past few decades and within material handling systems, significant improvements have been made to truck performance and capacity. Consequently, operating expenditures (OPEX) associated with fuel and maintenance have risen swiftly. In a mining operation, truck hauling systems now represent 40–50% of the capital cost and approximately 45% of the OPEX (Tutton & Streck, 2009). Additionally, material transportation costs are expected to increase due to longer haul distances arising from deeper and larger mines (Fleet et al., 2015). Finally, large fluctuations in fuel prices result in high risks associated with truck OPEX. According to the United States Energy Information Administration (2015), the cost of crude oil—the largest component of the retail price of diesel fuel—increased from US$24.31/barrel in 1986 to US$46.92/barrel in 2016, peaking at US$151.72/barrel in 2008 (Macrotrends, 2016)."

Jan 1, 2017

By D. Wolfe, R. Cleminson

"The Aurora North mine has been operating for more than ten years, and is the source of over half of Syncrude’s bitumen production. The hydrotransport systems at Aurora experience high rates of wear, and mission lengths on current slurry pumps are nominally 1,500-2,000 hours. Recent work has enabled a better understanding of the significant adverse effect of large particle impingement damage to impeller vane leading edges - which is the known life determining issue for Aurora hydrotransport pumps. A new pump design has been developed and installed at Aurora, incorporating significantly increased impeller diameter and pumping vane lengths. The new pumps are expected to triple Aurora’s previous mission length for hydrotransport pumps. Part II of this paper will share actual hydraulic and wear performance observed in the first several months of operation, and draw comparisons relative to what was expected for these pumps in design / development.INTRODUCTION Slurry Pumps are Critical Equipment at Syncrude Slurry pumps are a key component in Syncrude’s operations. In a typical Aurora application, each 5000 HP pump stage helps move over 8,000 dry tonnes per hour of oil sand, plus an equal volume of process water that has been added to create the slurry. The average impeller life in oil sand hydrotransport service at Aurora has been nominally 1,500 to 2,000 hours, or 12 to 16 million tonnes of oil sand pumped. Generally, the slurry pump application at Aurora has proven very difficult to improve due to the unique combination of high sand abrasivity, 125 mm (5”) large particle top size (lumps), and high flow rate relative to basic pump size; a factor that results in unduly high impeller vane leading edge speeds for the service conditions."

Jan 1, 2014

By Grant Arnold

Le Camp Minier de Matagami est situé dans la ceinture volcano-sédimentaire Harricana- Turgeon appartenant à la Province du Supérieur, sous-province de l?Abitibi, au Québec. Les gisements de métaux de base polymétalliques sont retrouvés exclusivement dans les deux domaines lithotectoniques comprenant l?association basalte-rhyolite (Matagami-Brouillan et Joutel-Raymond). Tous ces dépôts, à l?exception de ceux de Selbaie, sont de type exhalatif et représentent des dépôts volcanogènes à Zn-Cu, typiques de l?Archéen. Le complexe volcanique de Matagami est constitué principalement de deux phases de volcanisme tholéïtique. Les dacites et les rhyolites du Groupe de Watson, représentent la phase la plus précoce et celles-cis sont recouvertes par la seconde phase qui est constituée majoritairement de roches intermédiares à mafiques intercalées d?horizons felsiques, formant le Groupe de Wabassee. Un sédiment chimique sulfuré, la Tuffite Clef, marque le contact et l?hiatus entre ces deux groupes. Cette tuffite est reconnue à la grandeur du flanc sud du camp minier et représente l?horizon favorable à explorer puisque sa déposition a correwspond à une période d?intense activité hydrothermale. Le complexe volcanique de Matagami est limité au nord et au sud par des bandes sédimentaires orientées est-ouest, connues respectivement sous les noms de Groupe de Matagami et Groupe de Taïbi. Le Complexe intrusif de la Rivière Bell, qui occupe la base du Groupe de Watson, est un complexe lité consistant en une séquence stratifiée gabbroïque avec localement des niveaux stratiformes à concentrations d?oxydes magmatiques, la bordure de ce complexe est marquée par la présence d?un horizon granophyrique. Cette intrusion synvolcanique prétectonique, représente probablement la source de chaleur étant à l?origine de l?activité hydrothermale observée dans les roches volcaniques sus-jacentes. Suite à un levé aéroporté, le camp minier de Matagami a vu le jour en 1956 lors de la découverte du dépôt de Mattagami Lake, un gisement volcanogène de 25.6 millions de tonnes. Depuis ce temps, un total de neuf gisements ont été exploités et un dixième, Bell Allard, est présentement en production. En date du 31 décembre 1999, la production historique du camp s?élevait à plus de 41 millions de tonnes. Cette présentation mettra l?accent sur la géologie des récentes découvertes dans le prolifique camp minier de Matagami. Les ressources publiées pour le dépôt Persévérance sont de 947,000 tonnes titrant 19.12% Zn, 1.37% Cu, 32 g/t Ag et 0.40 g/t Au. Deux autres découvertes, Équinoxe et Persévérance Ouest contibueront à la ressource globale. Les trois dépôts sont situés au niveau de la Tuffite Clef même si les roches sus-jacentes ne sont pas celles typiquement observées dans les autres dépôts du flanc sud. Ces découvertes sont le résultat d?un programme d?exploration ciblé et soutenu, démontrant ainsi la possibilité de découvrir de nouvelles ressources même dans les camps miniers comme Matagami qui ont été explorés intensivement depuis plus d?un demi-siècle.

May 1, 2001

During the hydrometallurgical processing of the major base metals Cu, Zn, Ni and Co, the presence of iron is normally a serious complication, and iron separation from the pay metals usually constitutes one of the main challenges for the metallurgist. There are many instances, however, where the presence of iron is beneficial, or is even required. Two cases are presented where iron is required during the processing of base metals. The first example deals with the use of ferric sulphate to oxidize sulphides, more particularly copper and zinc sulphides, under atmospheric conditions. The results presented confirm that ferric ion leaching is efficient, particularly when the oxidant is regenerated during the process. The second case is the use of iron to solubilise refractory cobalt oxide minerals; examples, including pilot plant results, are presented for various ores from Africa and Central America. In both cases, this paper reviews the basic concepts involved and provides details of their application.

Jan 1, 2006

By Paul Krivokuca

Outline Quinsam Coal Mine ?? Location ?? Mine History ?? Safety ?? Production ?? Hiring 4S Mine ?? Depillaring design ?? Structural mapping, Risk assessment ?? Rock Bolt Design Selection ?? Training

May 1, 2008

By Richard Maurice

RÉSUMÉ La restauration du site minier Poirier, à Joutel s?est déroulée entre 1998 et 2001. Le principal élément des travaux a été la restauration du parc à résidus et des zones d?épanchement qui totalisaient 4,5 millions tonnes de résidus répartis sur une superficie de 74 hectares. Les résidus sont fortement générateurs de drainage minier acide. La première partie de la présentation consiste en un bref rappel du concept de restauration suivi d?une description des principaux éléments de travaux avec l?emphase sur les leçons apprises de l?exécution des travaux. La deuxième partie de la présentation est axée sur les résultats du programme de suivi en cours depuis la fin des travaux en 2001. Les éléments de suivi se rapportent à la baisse du niveau de la nappe phréatique à l?intérieur de la cellule, au tassement des résidus dans la cellule, aux mesures de température et d?oxygène à l?intérieur de la cellule et finalement à l?amélioration dans la qualité de l?eau de surface. ABSTRACT The reclamation of Poirier Mine, in Joutel, was carried out between 1998 and 2001. The main component of the works has been the reclamation of the tailings basin and tailings spill area which contained a total of 4,5 million tonnes of tailings and occupied some 74 hectares of ground surface. The mine tailings are highly acid-generating. The first part of the presentation will deal with a brief review of the reclamation plan followed by a short description of the main work components laying emphasis on experience gained during construction. The second part of the presentation will deal with the results obtained from the environmental monitoring program still in progress since the end of reclamation work in 2001. The aspects discussed include the drawdown of pore water inside the covered tailing pile, the settlement of mine waste material, the monitoring of moisture, temperature and oxygen underneath the liner and finally, the reduction of loadings in surface water.

Nov 1, 2002

By David Stephenson, Hugo Granados, Steven Klohn

"HudBay’s Constancia project is a copper molybdenum concentrator located in southern Peru. In 2010 Ausenco was contracted to perform a feasibility study optimization review which resulted in an improved design with significantly increased throughput capacity at a minimal increase in capital cost. Construction began in 2012 with commercial operation commencing in May 2015. This paper outlines the process plant design as well as describing the plant’s major equipment selections, start-up and early operations experiences.IntroductionHudBay Mineral’s Constancia project is located at 4200 meters above sea level (masl) in southern Peru, approximately 630 km south-east of Lima, Peru. The property can be accessed by road from Cusco, Peru, (approximately 110 km to the north), or from Arequipa, Peru (approximately 215 km to the south). Matarani, accessed via Arequipa, is the closest port.Constancia is located within the Yauri-Andahuaylas metallogenic belt. The region contains several large copper-gold-molybdenum porphyry deposits such as Antapaccay (by Glencore) and Los Chancas (by Grupo Mexico), and copper skarn deposits such as Tintaya (by Glencore) and Las Bambas (by MMG). Constancia’s ore reserves contain copper and molybdenum with trace amounts of gold and silver.Ore is mined by an open-pit operation. The process plant recovers copper and molybdenum concentrates, storing tailings in a conventional tailings management facility. Infrastructure at the site includes a grid power supply (via a 70 km overhead transmission line from Tintaya), water supply, workshops and an accommodation camp. Mine life is 22 years.Site construction works began in 2012 with first copper concentrate produced in late 2014. The project was executed for approximately 1.75B$USD.Ausenco’s design approach focussed on developing a capital efficient copper molybdenum concentrator. This paper outlines key features incorporated in the concentrator design, plant layout and equipment selection, as well as start-up experiences and early operational results."

Jan 1, 2016

By F. Habashi

The pioneer work on pressure hydrometallurgy was conducted in Russia at the end of the nineteenth, and the beginning of the twentieth centuries, by Karl Josef Bayer (1847-1904) and Vladimir Nikolyevitch Ipatieff (1867-1952), both working independently in Saint Petersburg. Bayer was studying pressure leaching while Ipatieff was studying the precipitation of metals and their compounds by hydrogen under pressure. Gradually, industrial applications took place first in the aluminium and later in the nickel industry. Today, the technology is well established in a large number of industries, such as uranium, gold, zinc, titanium, tungsten, and more recently copper.

Jan 1, 2004

By B. Haugrud, E. McConaghy, M. Collins, G. Smith

"Laterite ore processed by the Ambatovy joint venture in Madagascar is primarily limonitic in nature, containing approximately 40–45 wt.% Fe and 1.1 wt.% Ni. The process selected for treatment of this ore considered the behaviour and deportment of iron in each step of the commercial flowsheet. Such considerations included nickel and cobalt recoveries, reagent consumptions, liquid-solid separation characteristics, and intermediate and final product purities. In this paper, the results for the first three years of commercial operation at Ambatovy are compared with the design parameters, with emphasis on the behaviour of iron.RÉSUMÉ Le minerai latéritique traité par l’entreprise commune Ambatovy au Madagascar contient principalement de la limonite, composée de 40–45 % en poids (wt%) de fer (Fe) et de 1,1 wt% de nickel (Ni). Le procédé choisi pour le traitement de ce minerai tenait compte du comportement et du maintien du fer à chaque étape du schéma de traitement commercial. Parmi les facteurs pris en compte figuraient les récupérations de nickel et de cobalt, les consommations d’agents réactifs, les caractéristiques de séparation des liquides-solides ainsi que la pureté des produits semi-fini et final. Cet article compare les résultats des trois premières années d’exploitation commerciale à Ambatovy aux paramètres d’étude, en insistant notamment sur le comportement du fer.INTRODUCTIONThe main component of nickeliferous laterite ore is iron, and the Ambatovy deposit in Madagascar is no exception. Ambatovy ore is primarily limonitic in nature, containing approximately 40–45 wt.% Fe and 1.1 wt.% Ni. The nickel content of the ore is approximately 1/40th that of the iron content by weight; therefore, successful recovery of nickel depends on close control of the behaviour of iron in the selected process.The Ambatovy area is located 80 km east of Antananarivo, the capital of Madagascar. Exploration dates back to 1960, when the Malagasy Service Géologique carried out a limited pitting and auger-drilling program. Phelps Dodge Corporation (now Freeport-McMoRan Copper & Gold, Inc.) was granted the mining rights to the property in 1995 and carried out significant resource definition, environmental assessment, and engineering studies between 1995 and 2001 (Chou, Rooke, Williams, & Hanks, 2000). In 2003, Dynatec Corporation, which was formed in 1997 by the merger of Dynatec International Ltd. and Sherritt International Consultants Inc., signed a joint venture agreement with subsidiaries of Phelps Dodge to evaluate the Ambatovy nickel project. Dynatec became extensively involved in the development of the project, including process selection and pilot plant testing in Fort Saskatchewan, Alberta (Collins et al., 2004, 2005; Collins & Vardill, 2005; Collins, Buban, Holloway, Masters, & Raudsepp, 2009). Dynatec acquired 100% of the project in 2005 and a joint venture between Dynatec, Sumitomo Corporation, Korea Resources Corporation (KORES), and SNC-Lavalin Inc. (SLI) was formed shortly thereafter to provide funding for further development. SLI was responsible for engineering, procurement, and construction management of the commercial facilities. Sherritt International Corporation reacquired Dynatec Corporation, including 40% ownership in the Ambatovy nickel project, in 2007. The current Ambatovy joint venture consists of an integrated nickel and cobalt mining, processing, refining, and marketing enterprise between subsidiaries of Sherritt (40% owner and mine and plant operator), Sumitomo Corporation (32.5% owner), and KORES (27.5% owner)."

Jan 1, 2017

By Mark Rebagliati, John Payne, Jim Oliver

Abstract-The Campo Morado precious-metal-bearing, volcanogenic massive sulfide deposits occur in a lower Cretaceous, bimodal, calc-alkaline volcanic sequence in a major northerly trending belt in the Guerrero Terrane in northeastern Guerrero, Mexico. During upper Cretaceous to Early Tertiary greenschist-facies regional metamorphism, the rocks were deformed strongly into a northeast-verging fold-and-thrust belt. Three later stages of weak deformation were dominated, respectively, by kink folds, broad warps, and extensional faults. Most deposits occur in the upper part of a sequence of felsic flows and heterolithic volcanoclastic rocks or at its contact with overlying chert and argillite-sandstone. The Reforma and El Rey massive sulfide deposits are on the overturned limb of a major, thrusted anticline, and the Naranjo and El Largo massive sulfide deposits are to the south on the upright limb of the same major fold. The La Lucha and San Rafael massive sulfide occurrences are in an upper plate to the southwest which was thrusted over the plate containing the Naranjo and El Largo deposits. In several of the deposits, Au, Ag, Zn, and Pb are concentrated near the stratigraphic top, and Cu is concentrated near the stratigraphic base. Major minerals are pyrite, quartz, ankerite, sphalerite, chalcopyrite, and galena. Minor minerals are tennantite-freibergite, arsenopyrite, and pyrrhotite. Gold and Ag occur in argentian gold, and Ag also occurs in tennantite-freibergite. The cumulative inferred resource of massive sulfide for the Reforma, Naranjo, El Rey, and El Largo deposits exceeds 30 Mt, with the latter two deposits incompletely delineated. Underlying pyrite-quartz stockwork zones contain chalcopyrite, chlorite, and sphalerite. Hydrothermal alteration minerals in the stratigraphic footwall are pyrite, quartz, chlorite, ferroan dolomite, and ankerite. In the stratigraphic hangingwall, hydrothermal alteration minerals are sericite, calcite-dolomite, and lesser clay minerals and quartz. The deposits belong to a low-sulfidation, volcanogenic massive sulfide system formed in a subaqueous environment, and are of the bimodal, siliciclastic type.

Jan 1, 1997

By Mark Rebagliati, John Payne, Jim Oliver

The Campo Morado precious-metal-bearing, volcanogenic massive sul?de deposits occurin a lower Cretaceous, bimodal, calc-alkaline volcanic sequence in a major northerly trending belt inthe Guerrero Terrane in northeastern Guerrero, Mexico. During upper Cretaceous to Early Tertiary greenschist-facies regional metamorphism, the rocks were deformed strongly into a northeast-verging fold-and-thrust belt. Three later stages of weak deformation were dominated, respectively, by kink folds, broad warps, and extensional faults. Most deposits occur in the upper part of a sequence of felsic ?ows and heterolithic volcanoclastic rocks or at its contact with overlying chert and argillite-sand-stone. The Reforma and El Rey massive sul?de deposits are on the overturned limb of a major, thrusted anticline, and the Naranjo and El Largo massive sul?de deposits are to the south on the upright limb of the same major fold. The La Lucha and San Rafael massive sul?de occurrences are in an upper plate to the southwest which was thrusted over the plate containing the Naranjo and El Largo deposits. In several of the deposits, Au, Ag, Zn, and Pb are concentrated near the stratigraphic top, andCu is concentrated near the stratigraphic base. Major minerals are pyrite, quartz, ankerite, sphalerite,chalcopyrite, and galena. Minor minerals are tennantite-freibergite, arsenopyrite, and pyrrhotite. Goldand Ag occur in argentian gold, and Ag also occurs in tennantite-freibergite. The cumulative inferred resource of massive sul?de for the Reforma, Naranjo, El Rey, and El Largo deposits exceeds 30 Mt, with the latter two deposits incompletely delineated. Underlying pyrite-quartz stockwork zones contain chalcopyrite, chlorite, and sphalerite. Hydrothermal alteration minerals in the stratigraphic foot-wall are pyrite, quartz, chlorite, ferroan dolomite, and ankerite. In the stratigraphic hangingwall, hydrothermal alteration minerals are sericite, calcite-dolomite, and lesser clay minerals and quartz. The deposits belong to a low-sul?dation, volcanogenic massive sul?de system formed in a subaqueous environment, and are of the bimodal, siliciclastic type.

Jan 1, 1997

By A. R. Guest, R. Clayton, J. Jakubec

"The potential for mudrushes is a potential hazard that should be evaluated during cave mining studies. Mudrushes are a phenomenon that can have very different origins, but produce the same results: injury, loss of life, damage to property, excess dilution, production delays, or mine closure. Although mudrushes are more common in cave mines than other mines, any mining activity that enables the accumulation of fine particles and water is susceptible to mudflow. This paper describes the process developed by the authors during the past decade to evaluate the risk of mudrushes, specifically in caving and sublevel caving mines.RÉSUMÉ Un danger potentiel qui devrait être évalué durant les études d’exploitation par blocs foudroyés est la possibilité d’afflux de boue. Le phénomène des afflux de boue peut avoir des origines très diverses; les résultats sont cependant les mêmes : des blessures, des pertes de vie, des dommages à la propriété, une dilution excessive, des délais de production ou des fermetures de mines. Bien que les afflux de boue soient plus fréquents dans les mines exploitées par blocs foudroyés, toute activité minière qui permet l’accumulation de particules fines et d’eau est sujette à des coulées de boue. Le présent article décrit le processus développé par les auteurs au cours de la dernière décennie pour évaluer le risque d’afflux de boue, surtout dans les mines exploitées par blocs foudroyés et par sousniveaux foudroyés."

Jan 1, 2016

By Luis Castelli, Aldo Bonomelli, Giselle Schifferli, Claudio Zamora

"This paper introduces the operational concept and the description of a multi-site Remote Support Center for knowledge management and long-term process performance improvement.This centralized Support Center provides real-time monitoring of open-platform process automation systems, and on-line access to process data and control applications information for multiple sites.Considering that process automation is a key enabler to business performance improvement, sustaining effective performance benefits over time becomes essential. Unfortunately, changes in manufacturing process dynamics, technology obsolescence and in plant operational practices cause the control strategies to lose their effectiveness over time unless their performance is periodically evaluated, and if required, tuned to the new process conditions.A new concept in process automation is proposed through the addition of a new control loop based on performance analysis methodology which is intended to feedback process and automation operation information to system and process specialists, allowing for continuous manufacturing process improvement and sustainable production benefits through effectual control strategies.A remote support center can play a key role in the delivery of such services, by providing the base platform from which a comprehensive process overview and a centralized knowledge database can be executed and additionally, as an enabler for plant operational practices change.INTRODUCTIONA Benchmark on Automation Level in Copper Concentrators conducted by AMIRA in 2004, reported that the Codelco divisions scored below their peers in several categories.Codelco had thereafter been looking for a new automation concept, and had focused on process automation as a key enabler for process manufacturing and business performance improvement. The final decision was to create a strategic alliance with a world-class automation technology provider.The traditional approach based on isolated automation solutions/projects, showed that the control strategies benefits were decreasing progressively over time, because of the on-going need to adapt the control models to the ever-changing process conditions and different plant operational practices. Another consequence of this traditional approach was the wide variety of technologies and automation systems deployed in the different plant sites, with no common automation standards, and with low opportunities to transfer knowledge or practices."

Jan 1, 2010

By J. F. Jackson, R. W. Mau

"The first commercial installation in the mineral industry of the ""Verti-Press"" pressure filter was made by Falconbridge Limited at the Strathcona Concentrator to filter copper concentrate. The filtercake produced contains 6 - 7% H2O, an improvement from the 12 - 13% H2O produced by an internal drum filter, at rates of up to 20 t/hr. A novel slurry feed system incorporates a hose pump and a pressurized slurry accumulator.INTRODUCTIONIncreased copper production from Falconbridge Limited operational mines in the Sudbury Area has exceeded the current refinery capacity. A copper concentrate has been produced to overcome this constraint and has been shipped to custom smelters either as a slurry or as a 12 - 13% moisture filtercake utilizing an internal drum filter.With the treatment of the new Deep Copper Zone from the Strathcona Mine, copper concentrate production was forecast in excess of the installed dewatering capacity. The filtercake was too wet to transport by truck and the custom smelter refused to handle this product at the truck unloading site. The filtercake had to be trucked to a rail spur and transloaded into gondola cars. This system was expensive, incurred unaccountable losses and the concentrate was assessed a moisture penalty.To reduce the concentrate moisture content to permit direct shipment by truck, two basic systems were available; vacuum filter followed by a thermal dryer or a pressure filter. Past experience with the high capital and operating costs of dryers led Falconbridge to closely examine the pressure filter alternative.COPPER CONCENTRATE PRODUCTIONThere are two separate circuits at the Strathcona Mill; one treating nickel ore and the other treating copper ore.The rougher concentrates produced by both circuits are conditioned with lime and cyanide before the copper-nickel separation in a flotation columns. The concentrate consisting of cha lcopyrite with mi nor cubanite is very clean as shown in Table I. Currently 50% of the copper in the plant feed reports as copper concentrate, in the past, this has been as high as 70%."

Jan 1, 1990

By Lebeau M., P. Duguay

"The cost of occupational injuries and diseases in the mining industry in Quebec was estimated for the period of 2010 to 2012. The method used takes into account the financial and human costs assumed by employers, workers, and the community. To better direct research and prevention toward issues with the most significant consequences, the results are presented in various ranking tables, which stakeholders might find useful.RÉSUMÉ Le coût des accidents du travail et des maladies professionnelles dans l’industrie minière au Québec a été estimé pour la période 2010-2012. La méthode utilisée prend en compte les coûts financiers et humains endossés par les employeurs, les travailleurs et la communauté. Afin de mieux orienter les recherches et la prévention vers les problèmes ayant les plus graves conséquences, les résultats sont présentés dans divers tableaux de classement, qui seront d’une grande utilité aux parties prenantes. INTRODUCTIONThe mining industry is much safer today than it was 30 or 40 years ago, mainly due to a more qualified workforce, the use of automated equipment, and a corporate culture more focused on occupational health and safety (OHS); however, the number and the severity of occupational injuries and diseases continue to make this industry one of the most hazardous. In the province of Quebec, the mining industry accounts for approximately 0.4% of paid workers but is the source of 4% of fatal work accidents. It is, therefore, important to continue the prevention efforts already underway in the mining industry.The difficult global economy, which has affected the mining industry in the last few years, is an opportunity to reaffirm that sound management of OHS can have a positive impact on companies’ productivity and profitability. Occupational injuries and diseases are costly for the companies concerned and for society as a whole. Reducing their occurrence makes it possible to reduce not only the size of workers’ compensation board contributions but also several other financial and human costs."

Jan 1, 2018

By Norman O. Lotter

Drill core is preferred as the sample material for metallurgical and mineralogical characterisation and flowsheeting of an orebody. The question arises as to how to do this at the economic optimum, since geologists have several other strategic uses for their drill core. The limiting factors are the cost of extra drilling for the metallurgical testwork and the need to preserve the drill core record. In this study, the representative sampling of drill core at an economic optimum for metallurgical testing is addressed. This phase of the drill core work is preceded by earlier drill core characterisation - for which other appropriate sampling protocols are used - that has provisionally categorised the orebody into geometallurgical units. In stratified sampling of drill core, use is made of a version of the stratified approach to compound distributions proposed by Cochran in 1946. Use is made of Gy’s 50-piece minimum sample mass model to estimate minimum requisite sample mass. In the case where sampling and testwork are required on a Lifeof- Mine blend of a given ore deposit, whereby defined ore types or geometallurgical units are present, the sample mass requirement is significantly reduced by working from drill-core at the geometallurgical unit level. A case study using Raglan drill core is discussed. Using nickel as an indicator paymetal, and sampling at a fundamental variance level of 8%, the minimum sample masses for disseminated sulphides, net-textured sulphides, and massive sulphides are 3.80, 7.37 and 4.39 kg respectively. When the same drill-core is sampled as a Life-of-Mine mixture without knowledge of the geometallurgical units, the minimum sample mass increases to 84.28 kg. It is thus possible to assemble a representative Life-of-Mine sample of drill-core more economically, at the same time validating its representativity. Equivalent calculations for copper, platinum and palladium are discussed, with outcomes consistent with this finding. When all four paymetals are considered, one selects the largest minimum mass out of all four cases. This results in minimum sample masses of 11.67, 74.90 and 175.16 kg for disseminated sulphides, net-textured sulphides and massive sulphides respectively. The simulated Life-of- Mine blend would require a minimum sample mass of 377.33 kg to cover all four paymetals.

Jan 1, 2010

By W. G. Miller, J. D. Scott, D. C. Sego

ABSTRACT An overall study was conducted to evaluate the properties and processes influencing the rate and magnitude of consolidation for oil sands fine tailings produced using different extraction processes. As part of the overall study, a comprehensive description of physical and chemical characteristics of fine tailings generated by caustic and non-caustic processes was carried out. Ultimately, the influence of these fundamental properties on the compressibility, hydraulic conductivity and shear strength properties of the fine tailings was assessed. The characteristics of the fine tailings are presented in terms of index properties, mineralogy, specific surface area, water chemistry, liquid limits, particle size distribution and structure. A difference in water chemistry was concluded to be the cause of substantial differences in particle size distributions and degree of dispersion of the comparable caustic and non-caustic fine tailings. The degree of dispersion was consistent with predictions for dispersed clays established by the sodium adsorption ratio (SAR) values for these materials. A linear variation of increasing dispersion with increasing SAR up to a SAR value of about 40 has been suggested, above which fine tailings are completely dispersed. The observed dispersed or flocculated structures (viewed using a scanning electron microscope) supported the predictions based on SAR values.

Jan 1, 2010

"The measurement of error in assays collected as part of a mineral exploration program or mining operation historically has been undertaken in a variety of ways. Different parameters have been used to describe the magnitude of relative error, and each of these parameters is related to the standard measure of relative error, the coefficient of variation. Calculation of the coefficient of variation can be undertaken in a variety of ways; however, only one produces unbiased estimates of measurement error: the root mean square coefficient of variation calculated from the individual coefficients of variation.Thompson and Howarth’s error analysis approach has also been used to describe measurement error. However, because this approach utilizes a regression line to describe error, it provides a substantially different measure of error than the root mean square coefficient of variation. Furthermore, because regression is used, Thompson and Howarth’s results should only be used for estimating error in individual samples, and not for describing the average error in a data set. As a result, Thompson and Howarth’s results should not be used to determine the magnitudes of component errors introduced during geochemical sampling, preparation, and analysis.Finally, the standard error on the coefficient of variation is derived, and it is shown that very poor estimates of relative error are obtained from duplicate data. As a result, geoscientists seeking to determine the average relative error in a data set should use a very large number of duplicate samples to make this estimate, particularly if the average relative error is large."

Jan 1, 2007

By M. Cossette, V. H. Tran

"How can the durability of asphalt pavement be doubled without increasing highway budgets? Asphalt containing asbestos can provide the desired performance with additional costs being made up by longer life. The addition of a low percentage of asbestos to an asphalt mix permits a higher asphalt content without any consequent loss in stability. It is mainly the higher asphalt content that provides improved performance and durability, although the fibrous reinforcement plays a key role in preventing the propagation of micro-fissures. As well, several international studies show that, thanks to the latest production techniques, no environmental hazards need be incurred.RésuméComment doubler la durée des chaussées d'asphalte sans augmenter les budgets de voirie? L’asphalte contenant de l'amiante peut offrir les performances souhaitées et l'augmentation des couts initiaux peut être rapidement compensée par une durée prolongée. L’addition d'une faible teneur en amiante courte il l'enrobe de bitume permet des teneurs en bitume plus élevées sans subir une perte de stabilité en conséquence. C'est principalement la teneur accrue en bitume qui assure un améliorations propriétés physiques et une augmentation des performances mécaniques, ainsi qu'on prolongement de la durée. Cependant, le renforcement fibreux joue un rôle clef en prévenant la propagation éventuelles micro-fissures. Les nouvelles techniques évitent tous risques environnementaux"

Jan 1, 1991