Search Documents

By Jaracz K

At the operation of mine winders in deep shafts considerable oscillations of winding ropes may occur due to elasticity of both wind-ing and balance ropes. The amplitudes of longitudinal oscillations may reach + lm at relatively low frequencies, ranging from 0.5 to 2 c/s. These oscillations may be dangereus for the rope and produce several hazards to the winding installation as a whole. They may cause conside-rable instant accelerations on the pulley and dangerous tensions in ro-pe wires. The excessive acceleration may cause the uncontrolled rope slip on the pulley. Several methods of limitation of these accelera-tions were developed, some of them have been already in control system: of electric drive of the winder. The most simple ones are: a/ limita-tion of the rate of change of acceleration and retardation of the win-der /so called "jerk"/ and b/ the proper selection of regulators of the winder control system to get the optimal control. The trouble in solv-ing the problem of rope oscillations is that the dynamic system of the winder is a nonstationaryone owing to changing distance of conveyance from the pulley. Besides, the system is described by the equations with distributed parameters. The brief discussion of the theory and its practical aspects are enclosed as well.

Jan 1, 1985

By Fukui M

An increase in pig iron output by 50 per cent was aimed at after re-lining No.2 blast furnace of NAKAYAMA STEEL WORKS. This had to be achieved by increasing both the furnace volume (from 673 to 757 m3) and its productivity, Without equipment for high top pressure operation, high productivity was mainly attained by the following three measures; (1) improving the gas flow characteristics by maintaining a high ratio of agglomerated ores, increasing the strength of sinter and coke, and optimizing the charge distribution, (2) decreasing the fuel ratio by low Si operation and the use of hot blast, and (3) oxygen enrichment. In addition, the tapping controls for pig iron and slag were intensified. As a result of the above measures an excellent hot metal output of 2.7 tonne/m3/day was attained in April 1979 (monthly average).

Jan 1, 1980

By I Govender, T L. Moodley

Tumbling mills are grossly inefficient, using only 5 per cent of the total energy supplied for actual breakage. A significant proportion of this inefficiency is unavoidable owing to geometric limitations; rotating drum systems are prone to exhibiting certain regions (energy barriers) that resist particle entry thereby restricting the transfer of energy. Though such systems are inherently inefficient, improved modelling schemes may lead to slightly enhanced efficiency through better microscale predictions of key breakage drivers (stress, force). Central to achieving such incremental advances is the development of a universally accepted rheology for dense granular flows. Armed with a better understanding of these macro-scale ingredients, classical process modelling offers an efficient, spreadsheet friendly framework for recovering the spatial distributions of the comminution drivers. At this real-time level of process control, it should be possible to tune comminution operations towards more energy efficient configurations – the ultimate goal of this research. The present work employs validated DEM data to recover the full continuum field which will ultimately serve as a basis for calibrating process model outputs based on different rheological hypotheses. Such a continuumbased approach captures tensor properties like the shear stress and strain rate – both of which are necessary to developing a dense granular rheology. Moreover, DEM captures this data at the momentum transfer timescale of 10-6 s – no other measurement technique is capable of this level of spatial and temporal resolution. Importantly, the confidence in this DEM data is strengthened because it has been validated at the continuum scale using Positron Emission Particle Tracking (PEPT) kinematic measurements. Validated DEM data is derived from batch experiments conducted within a 300 mm ID laboratory drum using three and five millimetre glass beads at 60 and 75 percent critical speed; such mill speeds are typically encountered in the tumbling mill industry. Dimensional analysis is conducted using critical rheological parameters (shear rate, shear stress, granular temperature etc), which are key to not only developing a granular rheology but ultimately will be used to tune our mechanistic models.

Aug 24, 2022

Krupp Polysius AG, FRG, in close cooperation with Prof. Dr. K. Schoenert, FRG have developed the principle of the high pressure grind- ing roll POLYCOM. The POLYCOM mill basically consists of two counter-rotating rolls of large diameter and relatively small width, one of which is fixed and the other moving in slide blocks. The pressure required for comminu- tion is applied via the sliding roll by a powerful hydraulic system. The comminution takes place between the rolls under high pressure in the bed of material by nipping and compacting. The top feed size-depending on the rolls diameter -may be as coarse as conventional secondary crusher feed and the product is a compacted cake containing a high amount of fines created by micro-cracking. The amount of fines depends on the pres- sure (grinding force) applied. Operating results show that even in wet griding circuits capacity increases at downstream connected grinding mills of up to 100010 can be accomplished with an interconnected POLYCOM machine and energy savings of up to 25070 may be achieved depending on application. POLYCOM can be used in existing grinding plants for low-cost upgrad- ing of capacities but also as an advanced alternative to conventional crush- ing and grinding equipment in open or closed circuit configuration. A single industrial size 2.8m roll diameter POLYCOM machine may be fed with top feed size of up to 200mm and produce a finish product as fine- grained as known from rod and ball mills but with less energy consumption. Meanwhile, the POLYCOM high pressure grinding roll has established itself world-wide in the cement industry and is now entering the mining industry. POLYCOM machines are currently designed in industrial standard sizes of 1.0m to 2.0m rolls diameter and drive units of up to 2400 kW. This paper includes: principles of high pressure grinding, main fea tures of the POLYCOM machine, results of tests on various materials including Australian gold and copper ores carried out at the POLYSIUS research centre in Germany. Some examples of industrial applications of high pressure grinding will also be presented.

Jan 1, 1988

The gossan developed from the Whim Creek Cu-Zn-Pb-Ag sulphide deposit, in the Pilbara region of Western Australia, occurs near the top of a ridge in a dissected plateau 01 moderate relief. The gossan is characterized by the abundance of secondary ore minerals which indicates that it is relatively immature, due to climatic conditions and erosional stripping.The abundant presence of secondary carbonates indicates that the low pH generally resulting from sulphide oxidation has been neutralized, probably by the buffering effect of carbonatcs and silicates. Fe, Cu, Pb, 'Ag and Sn have been enriched in the gossan relative to the primary ore, and Mn, Ti, Co and Ni have been strongly depleted; other elements have remained substantially unchanged. The gossan has a strong gcochemical signature characterized by high Cu, Zn, Pb, As, Sb, Sn, Ag and Mo coutents. Boxwork textures are poorly developed, bu't the gossan has other diagnostic mineralogical features including sulphide inclusions in quartz and the presence of residual cassiterite.

Jan 1, 1982

The facilities used and techniques employed in the manufacture of steel and iron rolls at the Steel Foundry, B.H.P., Iron & Steel Works, Newcastle are described.

Jan 1, 1972

By Edwards A. B

This paper presents the results of an examination of four samples representative of the low-lead matte, high-lead matte, lead speiss and antimony speiss, respectively, produced during smelting operations at Port Pirie Smelters. The investigation was undertaken at the request of the Broken Hill Associated Smelters Pty. Ltd., as part of the research programme of the Mineragraphic Section of the Council for Scientific and Industrial Research.Analyses of the specimens are as follows:-

Jan 1, 1949

By Burnett C. C H

GEMNet, (Grade Estimation using Mapping Networks), is a grade/reserve estimation software system that uses the artificial intelligence technique known as neural networks to perform reserve estimates from both two- and three-dimensional data samples from a mineral deposit. The system is the result of research carried out over the past three years into the feasibility of using neural networks for reserve estimation at the AIMS Research Unit in the Department of Mineral Resources Engineering at the University of Nottingham. This paper describes the architecture of the GEMNet system including details of the neural network components of the system. The performance of the GEMNet system is then compared to several other widely used reserve estimation techniques on two reserve estimation examples. The results produced by the GEMNet system compare favourably with more conventional estimation techniques, but require fewer assumptions to be made about the form of the data used, and do not require the use of complex mathematical modelling.

Jan 1, 1995

By M E. Rakidjan

The DOZ underground mine at PT Freeport Indonesia is a copper and gold mine in Indonesia with current ore production of 42 000 tpd. Because of the mine expansion into the West DOZ more ventilation raises are needed to create a safe and healthy work place. All ventilation raises that connect the extraction levels to the underlying gallery exhaust drifts at DOZ are now developed using drop raise techniques. This paper describes the improvements undertaken to increase blasting efficiency, to decrease cost and reduce safety risks. This was achieved by using deck loading and presplitting, changing of stemming materials and prevention of excessive raise collar cratering (blow up).

Jan 1, 2005

By Paterson M. R, Spencer P. A

Vitrokele technology is a resin process that can be applied in gold plants to reduce both capital and operating costs. The Vitrokele resin can be used for both precious metal recovery and for recovering free and combined cyanide from effluent streams. Vitrokele resin has been extensively tested at pilot plant level and is now applied successfully at a commercial heap leach facility in Zimbabwe where it is used in place of activated carbon for recovery of gold from pregnant leach solution. Significant capital cost savings were achieved by installation of a resin plant instead of a conventional carbon adsorption plant. Operation to-date has not seen any significant physical or chemical degradation of the resin either in terms of adsorption capacity/kinetics or physical appearance/size. This gold recovery process is equally applicable to slurry streams where it would be implemented in stirred tanks with interstage screens in a similar manner to a conventional carbon adsorption plant.

Jan 1, 1996

Low-grade, porphyry copper type mineralization at the Moonmera prospect is related to the intrusion of a granodiorite porphyry mass into the Upper Permian "Gracemere granodiorite". Significant copper mineraliza- tion appears to be associated with the alteration assemblage quartz-sericite- kaolinite. The ore shell is surrounded by a zone where montmorillonite and kaolinite are in greater abundance and this assemblage is over- lapped, mainly at depth, by potassium feldspar alteration. Secondary biotite is abundant throughout the mineralized zone. Preliminary sulphur isotope results on the sulphide mineralization are compatible with a magmatic origin for the sulphur.

Jan 1, 1974

Supergene enrichment of ilmenite occurs through a complex series of reactions with initial oxidation and hydration followed by leaching and dehydration. Lateritization appears to be associated with the early phase of the supergene process and if ilmenite grains are encased in iron oxides no further alteration proceeds.

Jan 1, 1986

The Granites Gold Mine has far exceeded the design capacity of 300,000 tonne per annum during its first sixteen months of operation. The presence of considerable free coarse gold has made it imperative that the gravity section operate at maximum efficiency. The inadequacy of acid digest- ing facilities and trying climatic conditions prompted management to initi- ate investigations into the use of Intensive Cyanidation as an alternative method for upgrading gravity concentrates prior to smelting.

Jan 1, 1988

THE power requirements of the Mount Lyell Mining and Railway Company at Queenstown, Tasmania, have, since the inception of smelting operations in June, 1,,896, been derived continuously from the extensive forests in the watershed of the Queen River, adjacent to -the works, the firewood being of good quality, mainly composed of myrtle or beech (Fagus Ounninghami), eucalypts, and manuka (Leptospermum ericoides).The country is very rugged and mountainous, indented by numerous ravines and gullies, and intersected by many creeks, which are subject to periodical floods, under the influence of a heavy and persistent rainfall. The areas so far exploited aggregate a total of about 42 sq. 'miles, and this denuded country gives promise of ultimately becoming very valuable pastoral ground for cattle-raising. The tonnage of wood yielded per acre varies from 40 to 100 tons on stack measurement of 80 cub. ft. per ton, 60 tons per acre being considered a good average yield. The gross amount of firewood handled during the past 13 years approximates 1,200,000 tons, the greater portion of which has been obtained by ordinary tramming methods. The company's main line of railway, 3-ft. 6-in. gauge, has served as a trunk line for all supplies derived from the Queen River valley, south of the reduction works, while the northern and western areas have been exploited by means of...

Jan 1, 1911

By Adranyl W. W

Sub-level caving with bottom ore drawing has gained wide acceptance in rich, soft, low magnetic iron ores because it provides moderate ore dilution and ore losses. The main problem here is the high rock pressure exerted on sub-level drives situated in the sub-level sill pillars. To reduce this effect, the ore block is divided into panels. This paper illustraes the method of determining the maximum panel width providing low maintenance cost of sub-level drives.

Jan 1, 1995

By Crawford J

The paper asks the question 'Why Limit the HYDROTRANSPORT of material to the confines of your washplant'.A brief historical review of widely accepted slurry transport operation establishes that we are not talking about new technology - simply applying proven experience to an innovative continuous system.The paper reviews a simple potential application and compares capital and operating costs with conventional trucking.No attempt has been made to develop a complete mine plan and the comparison has been limited to material transport costs.

Jan 1, 1992

By Houchin MR, Jenkins DH

This paper examines the importance of processing to the properties and performance of high purity zirconia ceramics. Many of the principles discussed, however, apply to ceramic processing in general. For fabricated ceramic articles to display their wide range of high performance properties, they must be made fully dense. The precursor powder and postpowder processing requirements necessary to achieve full density in the fabricated body are discussed. Brittleness, the anathema of ceramics, can be overcome in zirconia by incorporation of toughening mechanisms. Transformation toughening and microcrack toughening and their origins in partially stabilized zirconia are reviewed.

Jan 1, 1989

By Davis A, Song J

A review of the literature indicated that several studies have been reported on the dissolution of gold using iodide/iodine, bromide/bromine leaching systems. Although the reagent costs are much cheaper for chloride/chlorine (or hypochlorite) this system has not been fully evaluated. This study was conducted to evaluate the fundamental chemistry of the chloride/hypochlorite leaching system. The CHEMIX program was used to model the stability of various gold species existing in the solution. The gold dissolution rate at different conditions was determined using gold strips immersed in various mixtures of chloride/hypochlorite. Leaching experiments were conducted to test the extraction of gold from various ores (oxidised and copper-gold ores), showing a promising prospect for this technique in various applications.

Jan 1, 1992

By McMahon DW

The major components of a mineral reserve estimate for project development purposes are described with respect to sampling, geology, estimation methods, mining factors, metallurgical factors, environmental factors, financial and other factors. Each of these components impact to varying degrees on the recoverable metal or product of a new mining project. The evaluation of a project is a complex process involving the best the profession can provide in terms of geological understanding, engineering ingenuity, metallurgical skills and financial evaluation.

Jan 1, 1983

The techniques used by the State Electricity Commis- sion of Victoria to handle and store brown coal in the both the raw coal and boiler bunkers are outlined. These tech- niques were adopted in agreement with the science of modern bulk solids handling. By successful balance between practical requirements and bulk solid handling system design require- ments the Commission expects to confidently attain reliable coal flow even for the most adverse of coal flow properties. Attainment of this goal demanded full attention to channel detail selection. An outcome of this attention has been the development of a novel bunker and discharge arrangement for handling extremely difficult to handle coals. Due to the novel features of this slot bunker outlet arrangement it's ad- vantages and disadvantages are discussed.

Jan 1, 1987