Search Documents

By Bhattacharyya A. K

The current methods for predicting pillar strengths are reviewed. A two-dimensional model, based on the Mohr-Coulomb failure criterion, is proposed for determining the compressive strength across the width of a long pillar. The model can be used to determine pillar strength and the depth of the crushed (ie yielding) zone from the pillar edges. The values of the parameters in the model, namely the cohesion and internal friction angle of the coal seam, friction angles at the contact of the coal seam with the roof and floor are determined by matching the strengths predicted by this model with the Bieniawski pillar strength formula for pillar width to height ratios up to 5. It is found that the derived values of these parameters are quite close to the results from laboratory tests. Based on the model, a preliminary analysis of pillar stability is made.

Jan 1, 1995

By Napier-Munn TJ

The Whiten model of crushers is currently being refined and extended at the JKMRC, with particular reference to cone crushers. This paper describes the model as a predictor of crusher power draw, discusses the application of the model, and considers the relationship between power draw and crusher performance.

Jan 1, 1988

Within the Mt Whaleback open cut mine the integrity of the final pit wall is achieved through careful rock slope design, use of rock reinforecement technology where marginal stability exists and use of controlled blasting techniques and excavation practices. By reducing the effective density of ANFO explosive within blastholes to around 0.2 glcm', and developing standard blast pattern designs for various rock types, blast damage to pit walls has been minimised. Accurate geological prediction is necessary for optimum blast design. Controlled blasting is undertaken where blasting occurs within 90 m of the designed final batter crest and hole by hole assessment of final limit blast patterns is undertaken before pattern charging. Shovels and trucks remove the bulk of blasted and dozed rock material, but due to the mine's variable pit wall slope configuration, bulldozer excavation of some critical design batters has been successfully Implemented.

Jan 1, 1986

By Shklyar FR, Bokovikov BA, Gordon YM, Scherbatskii VB, Yaroshenko YG, Shvydkii VS

The paper presents, for the first time, a complete mathematical model of the flow of gases in packed beds which describes the processes of gas-mechanics in iron blast furnaces and other shaft type smelting units. Good correlation between calculated and experimental results was obtained confirming the adequacy of the model. It is shown that the uniformity of gas distribution is related to the tuyere size and the extent of its protrusion into the furnace and that these variables may be used to regulate gas distribution across the furnace diameter. It is also concluded that furnace height has no significant influence on gas distribution. The necessity for a mathematical description of raceway phenomena has been experimentally proved. Conclusions from theory are shown to have profound implication to furnace design and operation.

Jan 1, 1975

By E Vargas, A Egana, M Alarcon, X Emery, A Barberan, A Lopez, N Morales, C Friedrich

"As the cost in time and money of data from sensors and small-scale tests has reduced, additional challenges have arisen. Although many mine data sets are not big relative to those in other disciplines, they are complex in other ways, and becoming too large to manage efficiently on personal computers. In order to take advantage of the opportunity offered by increased data, a diverse team from Universidad de Chile and CSIRO Mineral Resources has developed a virtual geometallurgical laboratory to support the computational requirements linking data acquisition with data-driven business decisions. A particular focus to date has been the development of user-guided workflow ensembles to enable comparison between plausible geometallurgical hypotheses.A case study has been undertaken using publicly available data from the Rocklea Dome iron deposit in Western Australia. A hypothetical mining schedule was produced from geochemical and hyperspectral drill core/chips data via the following steps: data preprocessing, exploratory data analysis, geochemical interpolation, block modelling, ultimate open pit design and scheduling. The key outcome of this study was the integration of workflow stages through new plug-in methods or modification of existing software. Outcomes from this study will be described in the paper in terms of geological and metallurgical data quality, analytical software support and ongoing computing infrastructure requirements.CITATION:Lopez, A, Barberan, A, Alarcon, M, Vargas, E, Ortiz, J, Morales, N, Emery, X, Egana, A, McFarlane, A and Friedrich, C, 2016. Progress towards Data-driven Mine Planning via a Virtual Geometallurgical Laboratory, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 287–294 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By G Partington

A regional scale prospectivity model was developed for Papua New Guinea (PNG) to identify areas of porphyry Cu-Au mineralisation. Weights of evidence modeling techniques were used to determine spatial correlations between porphyry Cu-Au mines and predictive maps created from available spatial data. These predictive maps were then combined into a final prospectivity map. Despite limited regional scale data the model has successfully identified areas of known porphyry mineralisation as prospective and has also identified areas where new mineralised systems may be discovered with further exploration. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By King MN, Travis IC

PISCES - the Planning and Information System for Coal Export Services has been developed by Port Waratah Coal Services (PWCS) to ensure the efficient and economic operation of the Hunter Valley Coal Chain. PISCES is a computer based integrated information and management system to coordinate operations commencing at minesites through the coal chain to shiploading at the Port. The PISCES system comprises a central database around which a number of planning modules interact. These include interactive programs for train planning and timetabling, stockpile management, berthing analysis and a coal shippers enquiry system. PWCS has previously developed - number of computer based systems for planning, controlling and monitoring complex coal handling operations and the extension of the PISCES system to the Hunter Valley Coal Chain is another initiative to assist the Hunter Valley Coal Export Industry in looking confidently towards the Future.

Jan 1, 1987

By Eaton R. A

The design of most underground mining machines shows little evidence of regard for ergonomic principles and operator comfort. Likewise, efficiency and ease of operation often appear to have been given little consideration in machines where ruggedness and simplicity have tended to dictate the configuration. Improvements in productivity are amongst the benefits to be gained by a different approach to machine design. The paper describes the philosophy and features of a test bed Load-Haul-Dump Vehicle undergoing trials at Mount Isa Mines. This machine is the outcome of a Research and Development Programme conducted by the Department of Mechanical Engineering at the University of Queensland and Mount Isa Mines Limited. The diesel powered test bed features an enclosed, air conditioned cabin, with a suspended operator's control station and electrically operated controls. An electronically controlled hydrostatic transmission incorporating wheel slip control, is another innovation. The performance and operator acceptance of the machine has led to adoption of most of the concepts in a new machine now being put into production.

Jan 1, 1987

By Weir D. R, Doyle B. N

The Sherritt Zinc Pressure Leaching Process is based upon the direct pressure leaching of zinc sulphide or lead-zinc bulk sulphide concentrates to produce zinc sulphate in solution and elemental sulphur in the leach residues. The zinc sulphate solution is compatible with conventional purification and electrowinning technology. The pressure leach residues can be treated for the recovery of elemental sulphur, lead and silver. With the conversion of sulphur to the elemental form, zinc pressure leaching allows zinc winning to be independent of sulphuric acid production. Direct pressure leaching of zinc sulphide concentrates was started commercially in October 1980. Continuing research and development studies have defined various pressure leaching configurations for integration with existing roast-leach operations, for grass roots plants, or for plants which are to have the roast-leach section completely replaced. These studies have included the treatment of zinc concentrates from various Australian producers and the development of process flowsheets for potential applications in Australia.

Jan 1, 1989

By Tonegato S, Wood M

The lack of objective data on roof bolting machines, bits, rods and overall system has created the need for an objective assessment of roof bolting. This work outlines a test rig for such objective assessment of component parts of the roof bolting system.

Jan 1, 1986

By Guvenir HA

This paper summarises a cost optimisation procedure by minimising the total drill metres and the overbreak that occurs in tunnel excavation in medium strength rock (uniaxial compressive strength

Jan 1, 1995

Cable bolts have been used extensively in the development of the footwall of the Mt Whaleback Mine as a part of the ground improvement program since 1986. High tensile seven wire stress relieved steel strand similar to that used in pre-stressed concrete and grouted in place with sulphate resistant cement have been employed for rock-mass reinforcement.Most of the footwall is developed in Mt McRae Shale which contains a 20 m thick pyritic shale layer 14 m below the ore/waste contact. Due to extensive folding of the footwall rocks, the pyritic shale layer regularly occurs on, or close to the pit slope. Rain water run-off seeping through pyritic shale becomes acidic to the extent where its pH value can be as low as 1.5.

Jan 1, 1992

By Buizen M, Eagleton A. C

The results of calibration trials conducted on parachute stoppings both overseas and in Australia under a recently completed NERD&DC grant, are presented. Applications of parachute stoppings, for rapid regulation and control of ventilation networks are described including use in blasting areas and rescue work. Several parachute-type stoppings are described and their applications Investigated

Jan 1, 1988

By Aziz NI, Bridgwood EW, Singh RN

One of the major impacts of using modern mechanised systems of mining is the production of large amounts of extraneous dirt intermixed with the Run of Mine output. The paper out- lines a proposed system of utilizing liquid tailings from coal mines to replace imported cementitious materials used in ground control and various other safety measures. A geotech- nical and cost assessment of the proposed system are also included. The paper concludes that it is possible to utilize processed tailings to cost effectively replace imported packing material for ground control.

Jan 1, 1986

By M Pratt

For up to 75 years large scale coal mining has been carried out within the Latrobe Valley region of Victoria. Withdrawal of groundwater from Tertiary aged sediments within the Latrobe Valley is essential to allow coal mining to proceed to depth. Water within the overburden layers, coal seams and interseams must be drained to avoid flooding during the mining process. The pressure in deeper aquifers must also be lowered to avoid floor heave, batter instability, and to maintain safe operating conditions as the mines develop in size and depth. The cost-effective management of the groundwater systems at and adjacent to the mining operations in the Latrobe Valley is essential to enable the efficient utilisation of the coal resource whilst minimising the environmental impact of this major industry in rural Victoria. Large-scale depressurisation and dewatering programs within the Latrobe Valley mines are managed through the use of detailed groundwater management plans. These incorporate:an extensive monitoring network which extends up to 60 kilometres from the mines; detailed mine scale and regional groundwater and hydrogeological models; and established operational procedures aimed at minimising capital and operational costs associated with the mine groundwater systems. Groundwater extraction system optimisation programs have been introduced into two of the mines with the aim of reducing extraction rates, improved risk management, and reducing operational costs by approximately whilst not compromising mine safety. This paper reviews the aquifer depressurisation and mine dewatering operations of the Latrobe Valley mines and illustrates the techniques utilised to ensure that high artesian pressures do not adversely impact on the mining operations.

Jan 1, 2003

By Gordon N

The in situ behaviour of claystone floors associated with the Wallarah, Great Northern and Fassifem Seams has been studied using a comprehensive suite of stress and displacement monitors. The instrumentation was supplemented by in situ and laboratory testing of the claystone materials. The instrumentation demonstrated that the presence of claystone floors is associated with floor heave, extra rib spall, and settlement of the pillar into the floor. Horizontal floor extensometers showed that the depth of extrusion of clay was limited to 1-2 in. A pore pressure transducer installed in a claystone floor demonstrated the possible existence of short-term undrained behaviour of the claystone. Long term swelling of destressed claystone was also documented. Settlement of pillars into claystone floors can be analysed using simple elastic theory. The assumption of plane strain is valid for most claystone thickness/pillar width aspect ratios. Floor heave can be analysed using bearing capacity concepts. However, it is considered that heave is the result of local bearing capacity failure in the rib spall zone. The advantage of this model is that the bearing capacity equation can be applied without resort to unrealistically high factors of safety.

Jan 1, 1992

Since I first enrolled to study Mining Engineering, the idea of working with big machinery and explosives has always appealed to me. After a few courses at uni, combined with vacation work and a number of presentations at the New LeadersÆ Conferences I had attended, I began to realise that the explosives side seemed to have more appeal than the others. As I look back on the past two and a half years that I have spent with Orica Australia Pty Ltd as part of their graduate program, I would have never imagined the dynamics of explosives in mining. This I put down to the ever changing and rapid development in technology converting blasting techniques into a defined predictable science. The opportunities I have been given have delivered all the appeals from when I first started my study. As a result of my entry into a profession that uses explosives to deliver broken rock in a range of mining and construction projects, through the use of advanced blasting technology and products, my experiences have been wide and varied. These experiences have included the use of OricaÆs i-konÖ detonator technology and blast design software to allow for blasting operations to occur in a range of environmentally sensitive quarrying and construction projects throughout New Zealand, to the implementation of various Orica blast based services aimed at improving dragline dig performance and reducing coal loss thus improve overall mine sustainability in the coal mines of Central Queensland, to the advanced utilisation of Orica explosive products and technology in a number of the worlds largest copper mines in Chile. I have witnessed first hand the blasting technology available within Orica Mining Services to both deliver fundamental changes in mining results and in turn kick off my career with a bang.

Jan 1, 2009

By OÆGrady P

Finite element analysis is becoming a routine component of design of longwall extractions, now superseding more traditional somewhat intuitive approaches. Finite element modelling is relatively inexpensive and provides an adequate degree of similitude to give satisfactory analysis. The physical modelling of two decades ago is now largely replaced by numerical methods of which finite element is the best known. Important data for finite element work are physical properties, including creep aspects, introducing the non-linearity of stress response.Various computer packages are available and some were used to model two specific UK examples, using both linear and non-linear approaches. It appears that non-linear approaches will yield most benefit. The use of materially non-linear analysis is merited by the greater similitude it provides between model output and real mine situations.

Jan 1, 1991

By Pollard D. M

Chalcopyrite samples from two different localities were leached in oxygenated mixed chloride-sulphate lixivants at elevated temperatures and atmospheric pressure. The oxidation of chalcopyrite was found to follow predominantly linear kinetics. The slope of the major region was dependent on stirring rate, oxygen flowrate and chloride concentration while only slightly dependent on the surface area of the sample leached. This region was found to predominate only at low temperatures. The oxidised chalcopyrite releases cuprous and ferric ions into solutions. Chloride ions complex these dissolved ions to effectively move the equilibrium of the leaching reaction to the right. When the level of chloride in solution was below 6 g/l, the unstable cuprous ions were found to reprecipitate with sulphur as covellite. When no chloride was present and the lixivant was a solution of sulphuric acid then ferric sulphates precipitated. The overall leaching reaction occurring in the leaching system is: CuFeS2 + 5H+ + 1.25 02 = Cu 2+ + Fe 3+ + 2S¦ + 2.5H20

Jan 1, 1987

By J Manuel, R Muddle

The demand for iron ore has increased significantly in recent years, with new iron ore sources being mined to meet this demand. As the composition of sinter blends changes with the availability and cost of iron ore, so too does interest in the impact of new ore types on granulation and ultimately productivity. This paper describes a study into granulating characteristics of seven iron ore types, including various hematite and goethite ores. The effect of ore type on feed moisture requirements, green bed permeability, green bed strength and granule size distribution was examined for single ore blends containing coke, flux and returns. The ore size distribution was varied in these blends and its effect on granulating characteristics examined. It was found that the optimum moisture requirement of the ore was more dependent on ore type than ore size distribution, but ore size distribution (and specifically intermediate particle loading) had a greater effect on green bed permeability. The saturation moisture value for an ore was found useful in predicting both optimum granulation moisture and green bed permeability.

Jan 1, 2005