Search Documents

In reviewing recent developments in the process mineralogy of gold it is convenient to distinguish between visible (>0.1 pm) and invisible gold (1 - 2 pm in size in polished section; these can scan the surface of a polished section, identifying the gold minerals, recording co-ordinates of the grains for subsequent examination, and making measurements of areas and sizes of the grains. However, problems of sample reliresentivity in polished section mean that such data may not give good quantification of gold mineral proportions and liberation/locking characteristics and other methods are required for this (amalgamation, cyanidation, ultra-fine milling and cyanidation). Characterisation of invisible gold in bulk material (eg a sulphide concentrate) can be done by mineral separation, ultra-fine milling and cyanidation or by quantitative point analyses of a large number of mineral grains. Analytical methods include electron microprobe analysis (detection limit normally -200 ppm but -10 ppm by using special techniques), ion microprobe analysis (secondary ion mass spectrometry - SIMS; detection limit -0.2 ppm) or proton microprobe analysis (PIXE; detection limit

Jan 1, 1992

During the past 18 months a rock mechanics project has been in operation at Renison Limited. The project was established to identify and investigate key problem areas that would affect future production at the Renison mine. An in-house approach was adopted, using shall compact equignent, to investigate ground behaviour. Information on the rock stress field was considered to be particularly important for an understanding of ground behaviour. A high horizontal stress component exists, which enables large flat dipping spans of hanging wall to be opened up, with support being provided by post pillars. The amount of support provided by these post pillars has been found to be low.

Jan 1, 1982

By M Stewart, J Vann, A Bu, D Frederickson

The Golden Gift is a recently discovered deep deposit below the main operating areas of the Stawell Gold Mine. At an early stage of the project, diamond drilling was used to define the mineralisation on sections approximately 100 - 150 m apart. The project economics were sensitive to both grade and tonnage. There were consequently two significant risks on resource quantification: risk on tonnage (ægeological riskÆ); and risk on grade (ægrade riskÆ). The degrees of freedom inherent in the geological model were considered to be potentially high because of wide drill spacing and likely structural complexity. To quantify geological risk three geologists familiar with Stawell mineralisation independently interpreted the deposit. This generated three plausible, different geological volume models. Conditional simulation was then used to quantify grade risk. Conditional simulation requires the user to define input statistics (histogram and variogram model) and a geological envelope. Based on global mean grade of an ordered set of simulations, æpessimisticÆ, æmedianÆ and æoptimisticÆ simulation cases were defined. The result was a 3 x 3 risk matrix with geological risk (the three interpretations) on one axis and grade risk (also three cases) on the other axis. An interesting result was that geological and grade risks were of a similar order of magnitude. Therefore a risk analysis of grade by geostatistical methods within a fixed geological model is of limited value, especially if the drill spacing is wide. After completion of this study, with additional drilling, the geological degrees of freedom at Golden Gift reduced substantially. A second Golden Gift risk study used a refined geological model to build a set of simulations to be used in preliminary mine design. A third simulation study in the deeper parts of the Magdala ore deposit, a well-drilled part of the mine with production history, demonstrates that the geostatistical simulation method used at Golden Gift is a robust and useful tool to quantify grade risk.

Jan 1, 2003

By J Tsiklieris, O Turner

Suppliers of products and services have a pivotal role in sustainable development in the mining and minerals industry. Reputable suppliers know their products and services, and the industry, and have unique knowledge of these in relation to their customerÆs needs. Petroleum hydrocarbon suppliers, in particular, impact upon a mineÆs sustainability because of the extensive reach of petroleum hydrocarbons into the mining and minerals life-cycle. The petroleum hydrocarbon life-cycle is a useful framework to enable engagement between supplier and customer on the issue of sustainability. The life-cycle starts with supply of fuels, lubricants and services at the mine, through to plant operation and maintenance, transport of mined products, ship loading, and finally through to mineral processing and other downstream value-adding. There are barriers to leveraging supplierÆs capabilities which have to be overcome before the industry will gain the potential benefits from such supplier engagement.

Jan 1, 2004

By Corbett GJ, Leach TM

A continued exploration programme has further defined the geology of the Tolukuma vein system, verified the resource indicated by Newmont, and identified potential for additional mineralisation. The resource at Tolukuma Hill, designated as zone C, is a mine recoverable 432,000 t at 18.1 g/t Au & 46 g/t Ag. Mining will be by a combination of open pit and underground at a rate of 100,000 t per annum. Processing will be by SAG mill, gravity circuit and CIL plant. A diatreme breccia, localised at an intersection of structures and a relationship of gold to base metal sulphides, are indicative of a strong porphyry association. Typical epithermal features such as crustiform banded quartz and quartz pseudomorphing platy calcite are also present and locally contain lesser gold mineralisation. Pre-existing dilatant structures have acted as a host to the ore fluids, resulting in the formation of the semi-continuous Tolukuma-Gulbadi veins over a 1100 in strike. A fluid flow model suggests that mineralizing fluids were sourced from a diatreme margin and migrated laterally along dilatant structures. Bonanza gold grades are interpreted to be derived through fluid quenching in the flexure between a hanging wall split, which hosts much of the Tolukuma Hill resource, and the feeder graben structure. Thus, the relationship between the pre-mineral structural geometry and fluid upflow at the margins of a diatreme breccia, controls the ore setting.

Jan 1, 1995

By de Lassar de Pressigny Y

IRSID has in its laboratories two experi mental counter-current reduction furnaces allo- wing the simulation of the physico-chemical conditions of reduction in any gas-solid coun- ter-current process, including the blast furnace and direct-reduction shaft-furnaces. The counter current is realized by an electric furnace mo- ving along a laboratory tube filled with the material to be tested. The reducing gas stream in the tube travels in the same direction as the furnace After reduction, twenty samples, with dif- ferent degrees of reduction and which can be related to different levels of an industrial furnace, are taken from the tube and subjected to various quality tests. Experiments were realized to determine the behaviour of various types of industrial pellets when reduced under either blast furnace or shaft furnace conditions. The results show the large influence of the reducing conditions on any pa- rameter characteristic of the quality of the pellets : reduction efficiency, swelling, cru- shing strength and disintegration.

Jan 1, 1974

In sizing of wet coal by the horizontal vibrating screen, screen openings to be used is much restricted, because coal is sticky and its bulk density is little. The electrically heated screen and other various types of screen had been tried to screen raw coal and coal as raw materials at a few mm. However, they failed to realize satisfactory results. On the other hand, fine sizing of coal is requested by many fields. For example, raw coal is desired to be screened at the fine rate, before being fed to the coal preparation control system in order to transport undersizes as unprepared coal particles and to reduce load in coal preparation waste water treatment system.1) Coals fed to the fluidized bed boiler also should be sized at a few mm. Regardless of many requests on fine sizing of coal, it seems that there are many cases to omit the basic screening process, because the screening is very difficult on a industrial scale. Size control as pretreatment of coal as raw materials is presented as one of the basic screening processes. In 1979, Kinki Industrial Co., Ltd. and Nippon Steel Corporation jointly succeeded in developing the vertical centrifugal screen. Closed -circuit crushing system by the use of this screen has operated actually at N.S.C, Hirbhata .Works, and realized the anticipated result. Consequently, this system has established the position as the most basic technology in the coal preparation. 2), 3), 4) This system has been also introduced to Nakayama Steel Works, Ltd. in 1982. This system termed the CPC (Coal Preparation Control) Process has been operated smoothly in both N.S.C. and Nakayama. Reported herein is the practical application of the vertical centrifugal screen termed V3-Separator. (V3 means vertical, versatile and vibration.)

Jan 1, 1984

By Gilbert DJ, Lemon NM

A case history of a two year study of low grade ores in the Middleback Range area with the objective of defining possible areas of interest from a combination of geological- petrological-metallurgical criteria. Covering the general geology of the area and ore types; the results of metallurgical testwork and the pattern of evolution of these tests; the petrological explanation of the results of the testwork; the culmination of the work in the selection of areas of best potential for more intensive work. Jaspilites consisting of magnetite, hematite and limonite with quartz and silicate-carbonate-sulphide minerals are hosts to high grade iron mineralisation but also constitute a large low grade iron Reserve.

Jan 1, 1975

From the viewpoint of mechanical efficiency, charges should be fully coupled and, upon detonation, should just fail to break the rock in compression. But because mining thrives on its cost-effectiveness rather than its mechan- ical efficiency, the explosive which generates maximum energy per $ should generally be used, even though the mechanical efficiency of this explosive's detonation products may be sub- optimum. Wherever possible, each charge should have a length:diameter ratio of about 20 or more and should shoot to a concavely biplanar free face that is both parallel and reasonably close to the blasthole. Success in obtaining parallel effective faces often demands the drilling of angled blastholes and, hence, will require intensified research and development efforts by drilling manufacturers, especially where hard strong rocks are encountered. Blastholes should be drilled on equilateral triangular grids and fired in a Vl or shallower V-type sequence using inter-row delays which ensure that good pro- gressive relief of burden is achieved. The conventional method of calculating Se/Be values (on the basis of planar effective faces) is often invalid.

Jan 1, 1986

By Grano S. R, Kilgariff B

The Renisun Tin concentrator treats an ore containing I's per cent till as cassiterite and 22 per cent sulphur in a range of sulphide minerals. predominantly pyrrhotite. The sulphide minerals are removed by flotation using copper sulphate (CuS

Jan 1, 1997

By Van Barnefield J G

This paper is based on an evaluation project engaged upon jointly by Mount Isa Mines Limited nnd" IBM Austra]ia Limited. Mount Isa Mines Limited produces most of its copper from large underground open stopes within massive orebodies. Variations in the position and shapes of these stopes can result in improved metal recovery. An interactive graphics system has been developed to assist the mine design engineer optimise his design. The system can assist the engineer throughout the orebody visualis- ation, initial design and optimisation phases of his design. At any stage the engineer may call upon the display of gridded mesh data, digitized ore outlines or existing stopes or development (drives, cross-cuts). This information may be viewed in plan or any vertical section or in three dimensions with rotation. Tonnage and grade calculations may be quickly performed for initial stope outlines or for modifications to them during the optimisation phase. The system design is highly modular. An array of functions for the manipulation of coordinate and line information may be linked with the development or stope design functions in whichever way the designer desires.

Jan 1, 1977

Detailed cash flow forecasts have always been almost essential as a basis for judging the viability of proposed new mining projects. In recent years attempts have been made explicitly to take account, in such forecasts, of the uncertainties surrounding the assumptions upon which they are based. With the risk analysis approach, Monte Carlo simulation of the cash flows indicates in probability terms the combined effect of these uncertain basic assumptions. While the use of risk analysis has been widely discussed, few specific applications to real projects have been reported. The application of such an analysis in the feasibility study of the large new Deelkraal gold mine presently being established on the Far West Witwatersrand gold fields by the Gold Fields Group in South Africa is described in the paper. The paper also indicates how one of the major sources of uncertainty, namely the gold content of the ore, can be`quantified in objective probability terms. This feature distinguishes the application fran other published accounts in which only subjective probability assessments have been utilised.

Jan 1, 1977

Black coals occur in most of the major sedimentary basins in Australia. In addition to the better known Permian coal occurrences of the Sydney, Bowen, Oaklands and Galilee Basins, coals of Permian age occur in the Arckaringa Basin in South Australia, the Bonaparte Basin in Northern Territory and the Collie, Perth and Canning Basins in Western Australia and the Tasmania Basin in Tasmania. Coals of Triassic age occur in the Ipswich Callide and Tarong Basins in Queensland, the Tasmania Basin in Tasmania and the Leigh Creek area in South Aus- tralia. Coal bearing rocks of Jurassic age occur in the Mulgildie Basin and Maryborough Basins in Queensland and in both the Queensland and New South Wales portions of the Clarence Moreton Basin and Surat Basins. They also occur in the Perth Basin in Western Australia. Rocks of Cretaceous age known to contain coal occur in the Styx, Maryborough and Laura Basins in Queensland, the Gippsland Basin in Victoria and both the Queensland and New South Wales portions of the Surat Basin. The coal measures have been deposited in a variety of sedimentary environments and the coals vary widely with regard to thickness, extent, banding characteristics, maceral and ash content. However, they are generally of low rank and most are suitable only for steaming.

Jan 1, 1975

The paper poses certain questions relating to mine design aspects of deep shaft pillars. It then explores these questions in relation to Western Deep Levels (South) where a sub-shaft system is to be sunk to 4 000 metres below surface to exploit two narrow tabular reefs in the down dip extension of the mine workings. After brief discussion of some broad considerations, the findings of a major rock mechanics investigation are reviewed. Some overall conclusions as well as the outcomes of separate studies of the anticipated behaviour of shaft pillars on each of the two reef horizons are outlined. The effect of this behaviour on the barrels of the shafts in the system and on the associated shaft excavations and in-pillar development is Cnnctdarcrl

Jan 1, 1986

The mineral pulp as it passes through grinding-classification, flotation and solid-liquid separation is examined in the context of it being a particulate fluid. By focussing on the complex viscosity and yield stress of the fluid, new control strategies are discussed. The mineral-particulate fluid is dominatred by non-Newtonian rheology (ie shear thinning, shear thickening, shear yield stress and compressive yield strength). The control of this Theology is seen to be dependent on the fundamental practice-particle interaction forces and with adequate information, it is possible to use the complex shear properties to advantage. The advantages, in terms of final waste and concentrate management, to high weight per cent solids in the mineral particulate fluid, are explored and control strategies outlined.

Jan 1, 1993

By J J. Campbell, G J. Wilkie

The ores of the Golden Mile exhibit considerable complexity. As a consequence, the operating company, Kalgoorlie Consolidated Gold Mines (KCGM), considered it important to develop a coherent database of information describing the nature of the many ore lodes in terms of (1) rock properties and mineralogical content, including relative proportions, grain size, associations and deportment of key elements between minerals, (2) the relative behaviour of consituent minerals in various stages of processing and (3) the nature of the final products and key intermediate streams. The paper describes a sequence of metallurgical tests covering comminution, flotation, gravity concentration, leaching and calcining, carried out on three lodes of the Golden Mile. Key samples generated by the testing were subjected to comprehensive size-by-elemental assaying and QEM*SEM mineralogical determinations of sulphide and precious metal associations. Significant differences between lodes were identified, and the impact of these differences on processing is discussed.

Jan 1, 1998

By Sarracino R. S

A number of ideal detonation codes are used internationally for estimating the strength of explosives compositions. Important and far reaching decisions by explosives users are ofen based on the predictions of these codes, but since different codes can deliver very different answers for the same composition, there is a strong possibility of decision makers being misled. In order to both provide a sensible basis for comparing the theoretical energy from explosives from different manufacturers and to prevent the entire rating system from slipping into disrepute, it is in the interests of all to reach agreement on fundamental criteria used by detonation codes for detemtining strength. The problem is illustrated by a case history and basic conventions are proposed, specifically the adoption of energy of reaction as a fundamental and code independent indicator of explosive energy, and agreement on disclosure by suppliers of key non-proprietary information. These measures would assist explosives customers in assessing the true strengths of explosives from the strengths calculated by the different ideal Codes.

Jan 1, 1990

By D Macfarlane, T McMorran

  This paper describes the design and construction of the upper section of the Pike River Mine Access Road. The road extends 11 km from Logburn Road alongside Big River on the West Coast of the South Island of New Zealand up Pike Stream to the new mine portal on White Knight Stream (Figure 1). This new road starts on alluvial terraces, then partially follows an old logging road before entering virgin bush and traversing the true left bank of a steep sided gorge on Pike Stream some 50 - 100 m above the stream before dropping down to the mine entrance. Its development has been an extended process from route selection, consenting through to design and construction.   The paper focuses on the 1 km section of road between the Amenities Area (Figure 1) and the portal. This section of road is a steep section through the gorge, principally on Conservation estate, and has presented the most challenges and required the greatest effort to obtain the regulatory approvals, prepare the design and to construct. This paper outlines the history of the challenges faced and how the road was successfully developed.

Jan 1, 2007

By Costello MC

An alternative process for desorbing and recovering metals from activated carbon has been developed, and is the subject of several patent applications by Micron Research (W.A.) The system uses the principle of conditioning the carbon in a strong alkaline cyanide solution followed by distillation desorption in a fractionating column, using the carbon as the column packing and methanol as the desorbing agent. The system offers the following advantages : (a) The processes of desorption, methanol recovery and reactivation are all carried out in a single column with the carbon itself acting as the column packing. No other desorption plant items or fractional distillation equipment are required. (b) The metal values are concentrated into the water content of the carbon and no other water is used except as condenser coolant. This produces very high grade gold silver solutions which give high current efficiencies in the electrowinning step. These high gold concentrations allow almost complete separation of gold and silver from copper in the electrolytic cell. (c) The process is completed to a tailing assay of less than 200g Au/tonne carbon in 15 - 20 hours allowing turn around of carbon batches on a daily Basis.

Jan 1, 1982

Computers represent substantial capital investment. A better return on that invest- ment comes from more effective use of the computer's facilities. By using Telecom's data communications facilities, more people in more locations can have ready access to those facilities.

Jan 1, 1983