Search Documents

By S Wasi, J Tobiczyk, J Roszkowski

Methane and fire hazards have a vital effect on work safety and continuity of mining plant operation. In the 1990s, the SMP hazards monitoring and ventilation control systems, based on continuous measurement of air parameters, were put into operation at nearly 30 Polish mines. These systems provide continuous measurement of methane concentration within the range of zero to 100 per cent with automatic switching off of electrical energy immediately after detection of potentially explosive conditions. Early detection of coal spontaneous combustion and open fires is made by continuous measurements of CO, CO2, smoke and O2 content in mine air as well as temperature changes in air and rock mass. The essence of the system is intrinsic safety of all underground instrumentation and uninterrupted central power supply from the surface. All abnormal and critical states are signalled to the mine control room. These trigger alarm and emergency procedures. The computer based ventilation monitoring and control system also performs the function of an expert system for fire detection and underground fire fighting. The mine control operator (dispatcher) makes use of stored data in computer escape route schemes and procedures for the safe withdrawal of miners from hazardous areas. The operator can put in motion intrinsically safe alarm signalling units and banners with programmed messages indicating escape routes.

Jan 1, 2005

By R M. Anderson, S P. Pigdon

The production of stabilised backfill at mine sites commonly uses Portland cement as the binder. Calcined gypsum has cementing properties and is cheaper to produce than cement. This paper discusses the strength of fills stabilised with calcined gypsum. Laboratory tests were carried out on specimens prepared from tailings obtained from four different sites to allow for the wide variety of tailings found in practice. The results show that the gypsum-based fills can achieve a strength of 1 MPa using around two and a half to four times the corresponding amount of cement.

Jan 1, 1998

By Edwards A. B

Yampi Sound is a small channel in the Buccaneer Archapelago (latitude 16° 10' S.; longitude 123° 40' E.), on the northern coast of Western Australia (Fig. 1), about 90 miles north of Derby, and 200 miles north-east of Broome.The iron ore deposits of Yampi Sound occur on an approximately S.E.-N.W. trending belt of islands which form the northern boundary of the Sound (Fig. 2). From east to west they are Koolan Island, Tarrant Island, Usborne Island, Cockatoo Island, Irvine Island, Kathleen Island, Flora Island, and Bathurst Island. To the south of the Sound lie Margaret Island, which is separated from the mainland by a channel only 60 ft. wide, Dorothy Island, and Gibbings Island. Some of the channels between the...

Jan 1, 1938

By D Chalmers

Drill and blast mining techniques are used to mine coal outburst prone and high gas content coals in Australia. As the risk of an outburst is increased in high gas content coal, it is considered that drill and blast is the safest way to mine coals that refuse to yield gas even after considerable gas drainage efforts. The availability of suitable explosives for drill and blast in Australia is dependent on the æBuxtonÆ tests. With the diminished coal operations in England, the type and supply of such explosives is tenuous, causing significant disruption to the production of coal in some mines. In an attempt to free up the availability of explosives a review of the methods used for the testing of coal mine explosives was undertaken to ascertain the scientific basis for these tests. It was hoped that this comparison would allow regulators to have the confidence in explosives that had been tested elsewhere. Although this was not achieved, it has spawned a major research project that aims to better understand the mechanisms involved so that either confirmation of the current testing regime can be achieved or more suitable and scientifically based tests can be adopted. This paper looks at the ongoing research program investigating the parameters that are involved with methane ignitions from explosives. By utilising high-speed data capture and processing the research project is trying to view an ignition as it happens to identify the mechanisms involved so that better explosives can be designed for the coal mining industry.

Jan 1, 2007

There is considerable economic incentive to increase the angle of open pit walls so as to reduce the total volume of waste to be moved to gain access to an orebody. However, a number of slope failures has increased the awareness of mine operators to the potential and consequences of slope failure. Sophisticated methods for the analysis of slope stability have been developed but they rely on an understanding of the appropriate parameters to describe the structural properties of the slope materials. Unfortunately, these properties change with time.The excavation of an open pit mine removes the constraint and weight of the overlying material and allows the newly formed slope to release previously locked in stress. The release of this stress allows the opening of joints and leads to a significant reduction in bulk modulus. The rock mass is also further affected by damage from nearby blasts. Such damage is cumulative and further reduces the modulus of the near surface material and weakens the bonds between structural elements in the slope.

Jan 1, 1992

By Minchinton A

CPeX is a non-ideal explosive performance prediction model. The model takes into account the rate of energy release, the extent of chemical reac- tion and the effect of confinement on energy release. The model resolves the explosive energy into `shock' and `heave' com- ponents as a function of explosive type, hole diameter and rock type. The predictions of the model are compared for a bulk emulsion, and a prill-doped bulk emulsion in soft rock. The predictions, based on calibra- tion of the model with simple unconfined detonation velocity measure- ments, show the significant effect of non-ideality on explosive Performance.

Jan 1, 1988

The Bellambi Coal Company Limited com menced longwall mining at South Bulli Colliery in 1965. At present it operates three long- wall units in two seams. Although results to date have been less successful than planned, it is apparent that this type of mining has tremendous potential in the particular conditions at South Bulli. Massive sandstone strata above the Bulli seam is the controlling influence on face conditions. The earliest equipment proved to be inadequate and the Company has progress- ively replaced and upgraded the roof supports and ancillary equipment so that the present units are capable of producing high and consistent outputs.

Jan 1, 1976

The Drake-Rivertree area lies in the far north east of the New England district of New South Wales. Drake is some 500 miles north of Sydney by road and 36 miles west of Lismore. Rivertree is situated 24 miles north of Drake.The Drake deposits were first worked in 1878 for gold which occurred in a very fine state in ferruginous gossan but at depth copper ore became more significant. The lodes at Rivertree, discovered in 1887, were worked for silver but mixed sulphides became more prominent in deeper levels.Several mines operated at each centre and each locality smelted its own ore.The mines at both centres were operated sporadically for many years though production was not particularly substantial.A number of the larger mining companies have shown a recent interest in this mining field with special emphasis on the Drake locality.GENERAL GEOLOGYThe two mining centres are situated to the north and south respectively of a belt of Permian marine sediments and volcanics similar to, and probably representing an easterly extension of, the rocks of the Emmaville district further west.E. C. Andrews (1907) recognized two stratigraphic units within what he called the Drake Series. The Lower Division consists of rhyolite flows, tuft's, breccias and agglomerates, followed by trachytic and andesitic tuft's containing cladochonns, thanmopora willcinsoni and other Permian forms.

Jan 1, 1962

By Hikosaka A, Chiba A

In a fundamental study of the physical chemistry of steelmaking slag, equilibra bet- ween hydrogen-water vapour gas mixtures and liquid slags contained in solid iron crucibles have been measured for four binary slags, FetO-CaO, FetO-Si02, FetO-TiO2 and FetO-Al203 at 14000C. From the data, the activity of iron oxide and the ratio of ferrous and ferric ions (A = Fe3+/Fe2+) were calculated for the slag composition. The best ionic model is found to be that based on regular solution of cations. The oxygen distribution between slag and metal is quantitatively expressed by this model over a wide range of slag composition.

Jan 1, 1980

By Smith CB, Boxer GL

The Argyle diamond deposits in the East Kimberley were found as a result of a long term exploration programme, begun in 1972 by the Kalumburu Joint Venture (KJV), to search for diamonds on the Kimberley craton. When CRA Exploration Pty. Limited joined the KJV in 1976, it was re-named the Ashton Joint Venture (AJV). The Kimberley craton was considered prospective by analogy with structural settings of diamondiferous kimberlites in Africa. Diamonds were found during regional drainage sampling in Smoke Creek in late 1979, which led directly to the discovery of the rich Argyle lamproite diatreme (AK1) and associated alluvial deposits of Smoke and Limestone Creeks. The diatreme intruded into quartzites, sandstones and shales of Adelaidean age, and consists predominantly of lapilli ash tuff, with minor coarse and fine ash tuffs, 'non-sandy tuff' and olivine lamproite dykes. Erosion of the diatreme has produced the alluvial deposits of Smoke Creek and Limestone Creek to the north and east. Argyle diamonds are of predominately industrial quality, and the typical diamond is a brown, irregularly shaped, frosted, heavily resorbed form with abundant graphite inclusions, well developed etch channels and prominent hexagonal surface depressions. The pre-feasibility evaluation of AK1 comprised diamond drilling, surface and underground sampling, metallurgical sampling, marketing studies and ore reserve estimation. The proven AK1 ore reserve is 61Mtonne at 6.8ct/tonne. Evaluation of the alluvial deposits gave results of Upper Smoke Creek, 580 000 tonne at 4.6ct/tonne and Limestone Creek, 1.7Mtonne at 3.5ct/tonne. Commercial production from the two alluvial deposits began in 1983 with production for the year reaching 6.2 Mct. Mining of the alluvial deposits at three to five Mct/year is proposed to continue until the start of mining of the AK1 deposit in late 1985 or early 1986 at which time a new processing plant and associated infra- structure will have been constructed adjacent to the AKl deposit in the Limestone Creek area. Production is planned at three Mtonne/year, producing 25Mct/year, which will make Western Australia the largest producer of natural diamond (by weight) in the world.

Jan 1, 1984

By C J. Adams, H J. Campbell, T Popham, A Goodall

Pounamu is a MSori collective term for semi-precious stone scientifically referred to as nephrite, semi-nephrite, jade or bowenite (tangiwai) that is composed predominantly of metamorphic tremolite in a felted, fibrous texture. It is Aotearoa/New ZealandÆs icon mineral material. Ownership and management of this important taonga (treasure) has been vested in Te Rnnanga o NgSi Tahu as part of a Treaty of Waitangi settlement process. Increasing demand from the tourist, jewellery, fashion and sculpture industries, as well as cultural renaissance, has placed pressure on the pounamu resource. This had led to nephrite importation, allegations that foreign material is being marketed falsely as New Zealand pounamu, and wider concerns over the potential for exploitation/over-use and theft of genuine pounamu.   Research is underway to characterise different pounamu source regions by defining their ægenetic fingerprintÆ. The geological age and radiogenic isotopic composition of Aotearoa/New Zealand pounamu is distinguished from other nephrite jade occurrences overseas, due to relatively young cooling ages. Strontium isotope ratios distinguish pounamu from different source areas within Aotearoa/New Zealand (whakapapa), with signatures reflecting the host terrane rocks (their family) and their position in a sequence of metamorphic events (their generation). The research will provide a tool for archaeological research, trademark and resource protection.   Mineral resource assessments normally aim to define the total volume/tonnage present, which is generally assumed to be finite, applying drilling and geostatistical modelling. Pounamu resource assessment requires a different approach, as its intrinsic value is insufficient to warrant modern exploration methods (eg drilling, geophysics). Pounamu is only known to occur at a restricted few in-situ (hard-rock) localities. It is primarily found in transported (alluvial) detrital river and glacial outwash deposits, where collectable material has short term variability due to erosion and transport processes. A new methodology is being developed aiming to define: +        the total resource present, +        the relative rate of change in the availability of that resource through erosion and other geological processes, +        active areas where new material is likely to be exposed (eg by erosion), and +        appropriate extraction rates for sustainable use. The methodology will provide a holistic overview of the resource in different regions of Aotearoa/New Zealand, and may be applicable to other transient or restricted natural resources that occur within geologically active environments (eg supplies of driftwood on beaches).

Jan 1, 2005

By P Dowd, A Adeli, C Xu, X Emery

Geometallurgical modelling is increasingly being incorporated into mineral resource modelling and estimation as a means of increasing efficiency, decreasing operating costs and reducing risk in mining operations. Traditional geostatistical workflows for geometallurgical modelling face several difficulties, in particular, related to the non-additivity of process response variables, to highly heterotopic data sets and/or to preferential sampling designs, all of which may explain why most attempts to estimate geometallurgical response variables from assay data and mineralogy are still based on statistics and machine learning. The aim of the work presented here is to demonstrate the applicability of geostatistics to estimate copper recovery from copper sulfide ores at the Prominent Hill Iron Oxide Copper-Gold (IOCG) deposit in Australia. As recovery is non-additive, the preferred workflow is the joint estimation of the masses of metal in the feed and in the concentrate, both of which are additive variables. While the mass of metal in the feed can be estimated from abundant online assay analyses, the mass of metal in the concentrate can only be estimated from a very limited number of laboratory-scale batch flotation tests. Traditional approaches to estimating the masses of metal in the feed and in the concentrate, such as simple and ordinary co-kriging, are described and discussed. A modified version of co-kriging is introduced, which incorporates linear relationships between the mean values of the input variables, in addition to a spatial correlation model. Co-kriging with related means is shown to outperform traditional simple and ordinary co-kriging in terms of precision, accuracy and consistency of the estimates, and offers a practical and efficient tool to deal with highly heterotopic and preferential sampling designs.

May 24, 2023

By Wright J

Large scale cut and fill mining in narrow silver-lead-zinc orebodies began at Mount Isa in 1964. Initially each orebody was one stope and access was via raises from the level above. Upholing was the principal mining method, although flatbacking was employed where ground conditions were more difficult. Developments since have included access via footwall inclines and connection of all stopes with major crosscuts. Flatbacking is the principal method. The most recent cut and fill operation is now fully mechanised using drilling jumbos, rockbolting jumbos and load-haul-dump units. Improved ground support and drilling and blasting practices have enhanced safety, recovery and productivity in all cut and fill operations.

Jan 1, 1988

The stratigraphic sequence west of Mount Isa contains the Judenan Beds, Eastern Creek Volcanics, and May Downs gneiss. It is an incomplete sequence as major north-south faults divide the area into four separatezones containing portions of these different units. The first three zones, which occur directly to the west of the Mount Isa Fault, consist of quartzites and quartz-mica schists which are uncorrelatable between zones but have been grouped together as the Judenan Beds. The most western zone contains an incomplete section of Eastern Creek Volcanics which rests conformably on a unit believed to be equivalent to the Mount Guide Quartzite; this is again underlain by the May Downs gneiss. A detailed description of the rock types is presented, but only a broad stratigraphic correlation is possible with the very much thicker sequence to the east of Mount Isa.The age of sedimentation is believed to be Lower Proterozoic and it may not occur in the type of geosynclinal basin envisaged by previous authors.This sequence is intruded by many small basic intrusions and also the Sybella Granite with its associated microgranite and pegmatites. The Sybella Granite consists of both a massive and a foliated phase; the latteris generally restricted to the margin of the main granite mass.Four regional metamorphic zones have been identified on the basis of their pelitic mineral assemblages; these are a chlorite, biotite, biotite-cordierite, and a sillimanite zone; separating each are prominent north-south faults.This metamorphism is a regional metamorphism which accompanies the first generation folding of the area and is not associated with the emplacement of the Sybella Granite. A very localized retrogressive metamorphism is also found in some areas of second generation folding.

Jan 1, 1972

Over the past seven years, a combination of New Zealand-, Australian- and German-led research voyages using the research vessels Tangaroa, Southern Surveyor, and Sonne respectively, have revolutionised our understanding of the Kermadec-Tonga arc-backarc systems. This convergent margin is the most seismically-active subduction zone system on Earth with convergence rates steadily increasing northwards from the Hikurangi Trench to ~250 mm/year at northern Tonga. In combination with the intra-oceanic setting, factors potentially producing magmatic, tectonic, and hydrothermal variability in this system include an increase in potentially subductable sediment northwards along-strike, intersection of the Louisville Ridge (hot-spot chain) and Osbourn Trough (paleo-spreading centre) with the arc at ~25¦S, and the possibility of Samoan (hot-spot) plume ingression in the northern Lau Basin. The bulk of the magmatism is submarine; whereas only a few emergent (some transient) volcanic islands exist, about 80 submarine volcanic centres of significant size (>1000 m above surrounding sea floor) are present between White Island in the south to north of Tafahi in Tonga. About 35 per cent of these centres are hydrothermally active. Important petrogenetic features of the volcanic rocks along this arc system are the abundance of rhyolite (some quartz-amphibole-bearing), and the outcrop of primitive olivine-clinopyroxene-phyric basalts in satellite cones of the major edifices. Many of the edifices consist of complex caldera systems. Eruptions from and degradation of these edifices were probably tsunamigenic. Many of the hydrothermal systems developed within the edifices are likely destroyed during the sector collapses which are the characteristic edifice degradation mode. There are three backarc spreading systems along this margin: the Havre Trough, Valu Fa-Eastern Lau Spreading Centre, and the nascent Fonualei Rifts. The latter are particularly notable in having captured the entire suprasubduction zone magmatic flux for a distance of about 150 km, shutting down the adjacent volcanic front arc volcanoes.

Jan 1, 2005

The emergence of a new range of database communication standards and software has provided the impetus for the development of a new approach to exploration and mining data management. The acQuire software produced by acQuire Software Pty

Jan 1, 1998

By Hainsworth D, Winstanley G, Gurgenci H, Corke P

Past experience has shown that the automation of the dragline swing motion requires real time monitoring of the bucket position. A current project at the Centre for Mining Technology and Equipment (CMTE) is aiming to achieve this using machine vision. The hardware platform is a Datacube MaxVideo 200 system. The images are obtained by a fixed camera installed on the dragline boom. The field of view is large enough to include the bucket in all possible configurations. Standard chain coding and run-length coding algorithms are used to process the video image. The three-dimensional bucket position is calculated by combining the output of the machine vision system with the rope length data obtained from transducers installed on drag and hoist drums. This information is then fed into a control computer which takes corrective action to suppress bucket oscillations before they reach dangerous levels.

Jan 1, 1995

Grade control plays an essential role in the good running of a mine. The factors at play are many, starting from a good analysis of the geology and a correct sampling procedure. Once this is achieved (and it is an essential prerequisite), the problem is to adequately define what is ore and what is waste. This paper tries to show, through a small example, how simple geostatistical techniques (variography, and moving average or kriging), can help in accurately defining these limits in a geologically homogeneous zone, thus allowing optimal use of the available information.

Jan 1, 1987

The Mount Morgan massive sulphide body occurs in a volcanic sequence of Lower or Middle. Devonian age, which is subdivided in the mine into "Upper mine porphyries", "Banded mine sequence", and "Lower mine porphyries". This sequence is intruded by latite, Mount Morgan Tonalite (360 million years), and late Permian dykes. Distribution of macroscopic ore textures and minerals in the orebody are discussed and evidence is presented indicating the pre-Tonalite, Devonian age of the orebody.

Jan 1, 1974

The Western New South Wales Electric Power Proprietary Limited is the central generating authority for distribution of power to the majority of the Broken Hill mining companies and the Broken Hill Water Board. This station supplies the whole of the power to North Broken Hill Ltd and Broken Hill South Ltd. It also supplies, power to the Southern Power Corporation for distribution to the Zinc Corporation Ltd. The Southern Power Corporation has a generating station which is tied in with the central generating authority.

Jan 1, 1957