Search Documents

The only functional underground Coal Mine in Nigeria is located in Enugu in Anambra State. For some years now the mine has been beset with a perenial problem of flooding. This has hampered produc- tion and some time ago the mine was abandoned. Recently money and equipment were made available to reactivate the mine. Attempts are now made to increase production as it is very much below demand. However, there are problems as the mine is below the water table under some major rivers and any advance exposes men and equipment to water surge. The paper traces the different attempts made to dewater the mine and the problems encountered in producing coal in this mine.

Jan 1, 1988

By Z Gao, D Liao, W Sun, S G. Pooley, J Wang, Z Shi, G Jing, S Ren, Q Chen

Yuanjing processing plant is a scheelite and wolframite plant in southern China. Water shortages and recent environmental regulations mean that the plant must reuse the wastewater that comes from the mining operation. This paper describes the efforts to reuse the mining and ore washing wastewater (MOW) in the processing plant. Initial attempts to reuse the MOW in the strong magnetic separation were unsuccessful because the magnetic media pack was seriously fouled by the micro-fine precipitate generated. The focus changed to reuse the MOW in the scheelite flotation circuit, which includes one roughing, one cleaning and three scavenging steps. Laboratory batch tests showed this would likely be successful because using MOW reliably improved the flotation performance in the laboratory tests. Then a 20 day industrial trial was run in the plant. The trial was very successful with the enrichment ratio of WO3 increasing from 17.4 to 23.6, while the recovery remained around 79.2 per cent. The industrial trial was so successful the company immediately adopted the new scheme, which has remained in use ever since. This technical solution not only alleviated serious water shortages, and satisfied environmental regulations but also improved the plant performance.

Aug 24, 2022

Samples weighing O·25 g are fused with 1 g potassium hydrogen sulphate, leached with 5 ml. of hydrochloric acid, and then diluted with another 5 ml. of acid. After settling, an aliquot of the clear solution is reduced with stannous chloride, and then a zinc dithiol solution is added to form a coloured tungsten complex which is extracted with petroleum spirit for comparison with standards.Concentrations down to 4 p.p.m. may be analysed at a rate of 100 determinations per man-day of 8 hr.

Jan 1, 1970

By B Walsh, M Cattani, S Verpaele

With the increasing sophistication of real-time sampling devices for occupational hygiene exposure assessment, research to objectively assess their performance is a priority. Using real-time monitoring equipment has several advantages over established gravimetric sampling methods, particularly their immediate results, lower overall long-term costs and no laboratory analysis costs, which are appealing to the mining industry due to the ongoing occupational hygiene monitoring programs required by the various regulatory agencies.

Apr 16, 2024

By I Gipps

The mining industry has come through a period of major change in community expectations regarding safety and environmental impact and these changes can be expected to continue in the future. These changes are ultimately reflected in Government regulations and industry safety standards and form the basis of the ælicense to operateÆ. Equally, advances in technology have made possible new equipment and processes either available now, or close to completion, that will allow mines to meet these more stringent expectations if properly introduced. Changes in technology provide opportunities for mine management to introduce new systems that will remove people from hazardous areas and lead to improvements in the ætriple bottom lineÆ. In a longer time frame of five to ten years, novel and advanced technologies that are currently being developed will deliver new mining methods and conversion of presently uneconomic resources to ore. This is consistent with the time frame required to develop a new mine from discovery. Strategic decisions can be taken now by mine designers to enable the introduction of these major technology changes. Examples of both practical and strategic opportunities are drawn from the integration of rock cutting/blasting, automation, electronic communications and new mining methods. This paper discusses emerging industry trends, changes to legislative framework and some practical choices for existing and imminent technology.

Jan 1, 2003

By C Samuelsson, Q Shu, A Lennartsson, F Gyakwaa, A Andersson, J Isaksson

The physico-chemical property, viscosity, is essential for pyrometallurgical processes and influences the settling rate of valuable metal droplets in slag, affecting the metal recovery. The copper slag from smelting furnaces typically contains between 1 and 2 wt per cent Cu, which equals to or is higher than in most sulfidic copper ores mined today, meaning the slag is a valuable resource for copper extraction. A low viscosity is desirable for slag-cleaning through a settling furnace where entrained droplets settle under gravity. One approach to control the viscosity is through the slag composition. The literature has limited data on the correlation between viscosity, slag structure, and optical basicity of iron silicate slag with FeO/SiO2, CaO, and Al2O3 as factors. Therefore, the present study evaluated the influence of these factors on viscosity and correlations with slag structure and optical basicity. The FeO/SiO2 ratio (at%/at%) and the CaO and Al2O3 content were altered in two levels, resulting in a two-level full factorial design with three factors. The study was done by synthesising FeO–SiO2–Al2O3–CaO–MgO–Cr2O3 melts, followed by water granulation. The melt structure of the samples was analysed with the help of Raman Spectroscopy. The viscosity was then estimated with a high-temperature rheometer using a Mo spindle and crucible. The results showed a correlation between the optical basicity, FeO/SiO2 ratio, and viscosity, where a high optical basicity and FeO/SiO2 ratio were beneficial for achieving a low melt viscosity.

Jun 19, 2024

By R Grogan

Nautilus Minerals (Nautilus) is a sea floor resource exploration and development company focused on developing the Solwara 1 Project, a copper-gold sea floor massive sulfide deposit in the territorial waters of Papua New Guinea, for which it holds a mining lease and associated environment permit.During the environmental impact assessment and project development phase, Nautilus completed a number of hydrodynamic modelling exercises in order to predict the nature, volume and extent of the plumes likely to be generated by the sea floor mining tools and return water discharge at the sea floor.The modelling was conducted using the suspended sediment fate model (SSFATE), developed by the United States Army Corps of Engineers and RPS APASA engineering consultants. The SSFATE model was originally developed in order to predict and manage dredging plumes, and has since been adapted for deep ocean sea floor mining. The model uses a Lagrangian approach to remove the limitations of grid resolution, and simulates far-field effects of sedimentation plumes by assuming that the average transport and turbulence associated with currents are dominant over the initial turbulence at the release point. The random walk procedure utilised in the model tracks particle size classes as they disperse and settle, and also takes into consideration any re-suspension that may occur following settlement (RPS APASA, 2014).CITATION:Grogan, R, 2016. Predicting, assessing and managing sediment plumes generated by sea floor mining, in Proceedings Life-of-Mine 2016 Conference, pp 124–127 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By I Canbulat, G Si, Y Duan, X Luo

The presence of unfavourable geological structures such as faults and dykes often can contribute to coal burst risk. Seismic events associated with rock fractures tend to cluster around these structures and it is important to understand the characteristics of seismicity for coal burst risk management. In an Australian underground longwall coalmine, two clusters of seismic activities close to the longwall face and within a section of the maingate roadway which was intersected by a major dyke were respectively identified. The induced seismicity in the dyke-roadway area was closely related to the longwall mining. These seismic events were located and the distribution of seismic events shows that more fractures were distributed on the inbye side of the dyke. The spatial-temporal changes of the seismic event locations delineate the fracture propagation as the longwall mined through the dyke. The frequency-magnitude relationship of seismicity was analysed and it was found that it changed significantly when the longwall was mining towards, through and past the dyke. The monitoring results demonstrate that because of the stiff dyke, the seismicity was intensified in the roadway section. It proves that the dyke promoted stress re-distribution and seismicity in its vicinity. More fractures were induced in the hanging wall of the dyke, whereas less strain energy was accumulated and released in the footwall of the dyke.

Nov 29, 2022

By G T. Hefter, P Singh

The effect of using SO2 as an anodic depolariser in the electrowinning of copper from aqueous acid sulphate solutions has been studied using cells without/with a ceramic diaphragm. In all cases SO2-saturation of the electrolyte/anolyte decreased the anode potential by 68 to 75 per cent largely due to a change in the anode reaction from the oxidation of water to the oxidation of SO2 . However, poor quality deposits and low current efficiencies are encountered if SO2 is allowed free-access to the copper being deposited at the cathode. This situation is easily avoided by using a diaphragm to restrict SO2 to the anode compartment and for these conditions the resultant copper deposits are of a similar (high) quality to those obtained in the absence of SO2.

Jan 1, 1999

By N Power, R Hassell, E Jones

Wiluna Mining Corporation are progressively re-entering the old Wiluna underground mining complex. The existing underground was abandoned in 2013 by previous owners and left to flood with water levels reaching above the East Pit portal and Happy Jack Pit portal and up to 300 m below surface in the Bulletin underground. Re-entering the mine commenced in 2017 with dewatering of the Bulletin decline. The underground development had been previously supported with friction bolts, with weld mesh in places. Until mid-2021 rehabilitation requirements were based on an external visual inspection of the installed ground support scheme. However, several incidents involving falls of ground due to corroded bolts have occurred during this time, showing that this approach was inadequate. The challenge the operation faced was should the entire decline be rehabilitated, the implication being not only a large rehabilitation cost but also the impact of severe delays to the mining schedule. The question was asked can the operation better understand the level of corrosion damage and potentially optimise rehabilitation requirements. A proposal to use a systematic approach to assess corrosion by environmental condition mapping, visual external corrosion assessment, and internal corrosion assessment via borehole camera inspections was provided and accepted by Wiluna Mining Corporation. The objective of this work was to produce a three-dimensional map showing the degree of corrosion on the reinforcement systems in the capital infrastructure, this would then be used to risk assess and prioritise rehabilitation requirements. This paper summarises the approach, methodology and results that provided the Wiluna mine planning team with information to enable planning of resources and budget to justify priorities of rehabilitation.

Nov 29, 2022

By M K. Singh

Mining is nothing but an art - besides being a science - of extracting valuable minerals from the womb of the mother earth. In this gigantic task, a large number of machinery and equipment are employed judiciously. Wire ropes play a vital role in lifting or hoisting men and materials under hostile/adverse working conditions and constitute a major item of investment on machinery/equipment. The economy of using a wire rope is a concern for engineers, users and the planners. The economic use of wire ropes for mining purposes largely depends on the following factors;Mechanical design considerations - which include tensile strength of wires, elasticity, resistance to abrasion and crushing, fatigue values, static and dynamic loads on wire ropes, factor of safety, fleet angle, etc. Metallurgical consideration - Composition and heat treatment of wire materials, defects like inclusions and voids, surface quality factor, lubrications, micro structural parameters. Operational consideration - Seizing and cutting of rope, storage, care and maintenance, cutting back, etc. Environmental consideration - Temperature and humidity, pit condition, dust, corrosive atmosphere, etc. In the present paper, an attempt will be made to suggest steps for achieving optimum economy while using the wire ropes for extraction of precious minerals and coal keeping in view the points noted earlier. Once technical viability is established, economy is the ultimate consideration for an industry for safe hoisting of men and material.

Jan 1, 2000

The ores described in this paper are from the two principal orebodies at Wiseman's Creek, a small village about 22 miles south-east of Bathurst in central-western New South Wales.The first official reference to mining at Wiseman's Creek is in "Mineral Statistics of New South Wales" of 1875, which reported that the Wiseman's Creek Copper Mining Company had proved a lode-later known as "North Wiseman's"-to a depth of 120 ft., where it was found to be 20 ft. wide. By 1876 the erection of a mill and smelting works had commenced, and the sulphide ore found to contain copper lead, zinc, silver and gold. Some oxidised ore was also being worked. Operations were, however, generally unsuccessful, and sporadic work up until 1907 produced only about 5,000 tons of ore. The other more important orebody of the locality-the Phoenix-was not opened until about 1895. By 1908, as reported by J. E. Carne, the shaft had been sunk 340 ft., with the extraction of both oxidised and primary ore. At the time of the slump in copper, pric'es in 1907 approximately 3,000 tons of, ore had been produced.Several smaller orebodies were discovered and worked during the same period as the North Wiseman's and Phoenix, but their output was more or less insignficant. THE OREBODIES AND THEIR GEOLOGICAL SETTINGIt is now impossible to examine the orebodies underground, but they appear to have formed a series of flat lenses, whose major axes were parallel to ,the foliation of the enclosing quartz-chlorite-muscovite schists. The largest ,of these lenses was worked as the North Wiseman's orebody, which was reported by Carne to vary in width from 1 ft. to 20 ft., and which probably extended discontinuously over a strike length of about 1,000 ft. The Phoenix orebody is stated to have varied from 1 ft. 6 in. to 3 ft. in width...

Jan 1, 1955

By R Urie

Dilution and loss of ore during the mining process invariably occur in all underground mining operations. This dilution and ore loss can have a significant effect on the performance and value generated from a mining operation. Further, excessive dilution or greater than anticipated ore loss during mining is often one of the key reasons for the underperformance of a mining project when compared to a feasibility study or annual budget. Mining professionals often go to great lengths preparing detailed mine plans, schedules and economic models only to then apply high-level estimates or rule of thumb values for dilution and mining recovery that can ultimately lead to inaccurate forecasts for the performance of a mine with the resultant loss of value due to the mining of uneconomic material or the loss of potentially valuable ore. This paper discusses processes and practices that can be practically used to manage dilution and mining recovery in an underground mining operation with a focus on understanding and then maximising value. The processes cover items such as the definition and measurement of dilution and mining recovery, techniques for the estimation of dilution and mining recovery, consideration of the economic implications, management of dilution and mining recovery through the stages of the planning cycle, and practices to reduce dilution and improve mining recovery. Common misconceptions and omissions are also discussed.

Mar 29, 2023

By X Yu, Y Shen

The iron ore products should be assessed in terms of in-furnace behaviour and overall furnace performance, their operation should also be optimised under industry-scale blast furnace (BF) conditions, in order to be sustainable and competitive, especially in the context of decarbonisation efforts in ironmaking. While lab and pilot-scale experiments can provide useful kinetics, they are expensive and risky and cannot replicate industry-scale blast furnace conditions for proper assessment and optimisation. In this paper, we review our recent progress at Shen Lab of UNSW in using state-of-the-art Computational Fluid Dynamics (CFD) models to assess iron ore products and examine the effects of their operations on BF behaviour in basic terms, including in-furnace phenomena (flow field, temperature field, species distribution fields etc) and overall BF performance (coke rate, reduction efficiency and top gas temperature etc). We have developed state-of-the-edge CFD models for different purposes, ranging from the static-state BF model featuring unique layered burden structures for offline assessment and optimisation knowledge building-up for iron ore products, to the transient-state BF model for online assessment and optimisation of iron ore productions by describing the transient behaviours of iron ore productions under industry-scale conditions. First, we have studied several iron ore products including the iron ore products used in the present BFs and emerging iron ore products like carbon composite briquette and iron-coke. Second, several iron ore operations are studied including optimisation of conventional burden operations like oxygen enrichment, batch weight tuning and new operations like coke central charging and hydrogen injection in BFs. Third, some time-sensitive operations are also investigated including the use of wet burden materials and the drop in blast temperature on BF performance. These CFD models offer cost-effective research tools for understanding the effect of iron ore products on BF performance and serve as a reliable marketing tool for existing and emerging iron ore products under a wide range of BF conditions.

Sep 18, 2023

By G R. Dickens, N H. S Oliver

The genesis of giant hematite ore deposits in northwest Australia remains a contentious topic in part because key evidence supporting a unifying genetic model has not been found at all deposits. In particular, several papers have proposed that carbonate replacement of silica layers in banded iron formation (BIF) by basinal brines is a requisite first step toward ore formation. This initial hypogene stage is inferred primarily from the presence of silica-poor, carbonate-rich rocks found below ore and along normal faults at the Mount Tom Price and Giles Mini deposits. However, until recently such rocks have not been identified at the largest martite-microplaty hematite deposit, Mount Whaleback. In this study, samples of the upper Mount McRae Shale are examined for their chemistry, mineralogy and petrography. These samples were collected from several key locations, including within drill core that penetrates an area immediately beneath ore along the Mount Whaleback fault at Mount Whaleback. Compared to unaltered black shale from Wittenoom Gorge in the north and altered black and red shale at Mount Whaleback, reddish-green shale below the Mount Whaleback deposit is significantly enriched in MgO and CaO and depleted in SiO2. Samples of this shale consist predominantly of fine- to medium-grained dolomite and ankerite cut by chlorite and carbonate veins, contrasting with unaltered equivalents that contain mostly stilpnomelane, K-feldspar and relatively minor carbonates. This alteration is distinct from assemblages developed during regional metamorphism, and possibly represents hydrothermal alteration after metamorphism. Although several questions remain unanswered, these results support models that invoke an early hypogene stage during the formation of the martite-microplaty hematite deposits in the Hamersley Province.

Jan 1, 2005

By J C. Furness, F S. Cannon

Metal casting operations are a significant source of hazardous air pollutants. In particular, high production iron foundries emit significant quantities of volatile organic compounds (VOCs) during pouring, cooling and shakeout of iron castings made in green sand molds. End-of-the-pipeline capture and destruction methods to reduce VOC emissions add crippling costs to foundries. Alternately, the incorporation of advanced oxidants (AO) into metal casting green sand systems has been shown to reduce emissions from high production iron foundries in the US, and at the same time reduce operating costs. Cost savings are driven by the benefits of AO in clay recovery systems. Emissions reductions are the direct result of cascading AO-based reactions taking place in green sand molds. This sustainable greening of the metal casting process is a prototype for the development of other AO and non-AO process-based solutions for sustainable high temperature processing of materials. Fundamentals of AO technologies will be discussed along with the performance characteristics of AO processing systems in the metal casting industry and the breadth of other processing and remediation applications for which AO technologies have the potential to be successfully employed.

Jan 1, 2002

Lateritic nickel ore occurs as a supergene or residual deposit as a result of the tropical weathering of underlying ultramafic rocks. The mineralisation may be as hydrated Ni-Mg silicates, like garnierite (silicate ore); or as hydrated Ni-Fe oxide (oxide) ore. Non-sulphide ore represents only 30% of the tonnage mined, but represents 85% of the total world's nickel reserves. A typical lateritic profile consists of 4 zones above the unweathered ultramafic parent rock: Zone 1: the "upper laterite" which is dark red-brown, porous and concentrically structured. It contains 0.2 to 0.8% Ni, 48.0 to 72.0% Fe, and 0 to 9.5% MgO. It is often capped by a ferricrete crust. Zone 2: the "middle laterite", which is red-brown to light brown and more porous than the above zone. It contains 0.8 to 1.5% Ni, 42.0 to 48.0% Fe and 0.5 to 6.0% MgO. Zone 3: the "basal laterite" which is yellow-brown to yellow-orange,

Jan 1, 1974

The considerations which led to the decision to_ install discs at the Dampier Pellet Plant of Hamer ley Iron Pty. Ltd. are described. Initial testwork showed that the ore could be ground dry in open circuit to a Blaine index of 2500 cm2/g and that it pelletized readily. The various design criteria including diameter, slope, speed, motor size, depth of sidewall, feed point and water spray location were then determined. Plant performance after commissioning is described including the various problems encountered and the modifications since carried out to overcome them. The main problem was quickly identified as disc feed rate control. Various bin and bin feeder modifications were tried to overcome the effects of the fluidising characteristics of the dry ground ore. Other factors found to affect disc operation are ore size distribution, additives and operator competence.

Jan 1, 1974

Thank you for the opportunity to speak at this important conference attended by aspiring mining professionals, some of whom will become the leaders of the mineral resources industry that forms the solid foundation of AustraliaÆs past and that will fuel the exciting growth of AustraliaÆs future.I want to briefly touch on the history of our business, then look at the opportunities that exist in the contract mining industry and finally comment on what the educators need to consider in their curriculum to meet the needs of our business. Byrnecut started out as an idea in early-1987 developed by a group of four mining people. At the time the industry was on the high end of a mining boom, the era of the Bonds, Connels, Skases and so on. Riding on this wave of euphoria we borrowed $600 000 from the National Australia Bank and, without having enough knowledge to lose sleep over the potential risks, started business in mid-1987. The euphoria quickly evaporated with the 1987 October stock market crash. The bank pulled our overdraft, equipment finance rates increased to over 20 per cent per annum and my house was mortgagedseveral times over. The business learning curve was extreme for a young mining engineer who had developed his trade in the relatively sheltered environment of a large public mining house, namely WMC. We were somewhat bitter that the banks had done a runner. We were a private company, backing the business with personal assets with our shoulders to the wheel, whilst the Bonds of the world had theirnoses in the trough ripping off mum and dad shareholders. All of this had a sobering effect, namely keep your feet on the ground, stick to the knitting, work hard and worship cash flow. Since that stressful but adrenaline pumping beginning the company now employs over 600 people and is now working for major mining houses at over a dozen locations in Australia, east Africa and WesternEurope and the National bank is again our banker. On this basis I consider myself qualified for the subject of this speech.

Jan 1, 2002

By M Paakkunainen

Sampling is often the most critical part in process analysis. When the mean of a continuous lot, such as a process stream within a given time interval, is estimated by calculating the mean of several samples, the uncertainty of the estimated mean depends usually on the sampling strategy. Three different strategies can be used: systematic, stratified or random sample selection. The standard deviation of the lot mean is different for these methods so that systematic sampling usually gives the smallest and random sampling the largest standard deviation. Pierre Gy developed a method where the sampling errors of one-dimensional lots for these three strategies can be estimated from a variogram, which is calculated from a variographic experiment, ie from a set of one-dimensional time series measurements with fixed sampling interval. While variogram is an excellent tool for characterising and displaying the variability of autocorrelated processes as function of time, the sampling error estimation from it is quite laborious, however. In this work an alternative method for estimating the sampling errors was developed. The process is divided into strata of equal sizes, varying the length of strata similarly to variographic analysis. For stratified sampling the standard deviation estimates are obtained by analysis of variance and for systematic sampling by fitting a linear regression line to each stratum and calculating the residual variances. By pooling the individual variance estimates the variance estimates that are corrected for autocorrelation are obtained. The new method was tested with simulated and real data sets having periodic, random and/or drift fluctuations. For stationary processes the results agreed well with the results of the GyÆs variographic method. The method can probably be generalised to estimate the sampling variance of higher-dimensional lots.

Jan 1, 2005