Search Documents

By Koppe J. C

This study presents the procedure of mine modelling and reserve evaluation by means of statistics, computer interpolation methods and aerophotography interpretation. All data are from Carbonifera Treviso, Laura Muller City, Santa Catarina State, southernmost Brazil. From 22 bore holes and nine trenches opened in the coal seam outcrops, a data base including level references and thickness of all rock formations was created.Using this information, basic statistic analysis was carried out, showing that there are three different populations (three modal distribution). These populations defined three geological blocks with different characteristics of overburden removal and mining methodology. This mathematical approach for analysing geological data is very important for correct mine planning and complementary prospection.

Jan 1, 1993

By Leach B. G

A geostatistical study was made of diamond drill hole intersections within 18CC stope block at the C.S.A. Mine, Cobar, N.S.W. The stope block is located in 18CC orebody which is a massive sulphide - multiple vein, Copper-Zinc type, lacking clear definition on gangue mineralogy, base-metal assays and total sulphide considerations. Of the variograms constructed for inter- section width and copper, lead and zinc grades and accumulations, only zinc displayed behaviour amenable to model fitting and kriging procedures. Zinc grades were calcu- lated for sub-blocks comprising the total stope block and comparison with equivalent grades determined by traditional methods showed them to be generally less extreme in the highest and lowest grade sub-blocks. The total-block grades derived by the two methods were almost the same. It is suggested that the failure of copper to show variogram continuity might reflect the difficulty in defining the actual 18CC orebody, a proposition which is supported by the poor continuity in the variogram of horizontal width. In the case of lead the poor continuity may be due to the frequent manner of occurrence of galena as coarse grained patches of limited extent. The results of the study, did not provide a convincing reason to depart from the traditi- onal methods of grade estimation at the C.S.A. Mine.

Jan 1, 1979

By D J. Brake

The importance of mine ventilation to health and safety in both coal and metalliferous mines has been long recognised. The primary and secondary ventilation systems in most metalliferous mines incur 50 per cent or more of the total mine electrical power consumption and frequently about 10 per cent of total underground mine operating costs. The requirements for ventilation-related horizontal and vertical development, fans and cooling have a significant impact on mine capital costs and also on mine schedules and start-up times and hence cash flows. There are increasing pressures on regulators and miners to reduce airborne contaminants such as diesel particulatematter, nitrogen dioxide and heat (wet bulb temperatures), and significant pressures to reducegreenhouse gases such as fugitive methane emissions from coalmines and the carbon dioxide footprint of both coal and metalliferous mines. Many previously Australian miners are now globaloperators and have extensive overseas mining operations where local ventilation standards and expertise may not be consistent with Australian practices. The role of the site ventilation officer is also changing with strict new requirements for the statutory position being introduced into Queensland metalliferous mines and the potential for this to become more widespread. Recent regulator and parliamentary review committees have identified systematic shortcomings in mine ventilation compliance, and statutory certificates in both Queensland and NSW now require continuing professional development to maintain currency. Public and investor support for mining are also increasingly contingent on safe, healthy and environmentally responsible practices and the standards for these are frequently tightening. Good ventilation design and operating practices that are consistently well executed therefore contribute significantly not only to a safe and healthy mine but also to a productive and cost-effective operation and the ongoing social licence to operate. There are a variety of ways of providing technical design and oversight into a mine’s ventilation systems; this paper explores some current trends in ventilation standards and statutory requirements, as well as ways to support and develop mine ventilation staff for both domestic and international operations and also the emerging senior technical roles of Group/Principal/Corporate mine ventilation engineer.

Oct 12, 2022

By S J. Schafrik, E S. Gilliland, E C. Jong, J Waynert, C W. Weiss

Two commercially available through-the-Earth (TTE) communications systems were evaluated at an active underground longwall mine in West Virginia. One system utilises magnetic field (H-field) antennae while the other system utilises electric field (E-field) antennae to achieve communication. A large portion of this mine is overlain by an inactive gas-oil field composed of densely spaced wells. This feature provided a unique opportunity to determine the impact of cased wells on both TTE technologies. The following communication modes were investigated: surface to underground, underground to surface, underground to underground and real-time two-way communications. Standard deployments of the TTE systems using the manufacturer’s recommended procedures were able to achieve clear communications between underground and surface locations under certain circumstances. As a result, the design and deployment that will optimise TTE transmissions are unique to each system and to the specific area of the mine. This field study was conducted as a part of a larger multisite evaluation of available TTE systems in an effort to determine their operational sensitivity. The performance of these two TTE systems suggested that one may be preferable over the other depending on the conditions present during deployment.CITATION:Jong, E C, Schafrik, S J, Gilliland, E S, Weiss, C W and Waynert, J, 2015. Pairing magnetic and e-field through-the-Earth communication systems based on mine site conditions, in Proceedings Third International Future Mining Conference, pp 245–252 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

In this year marking the centennial of the Geological survey of Western Australia, it is appropriate that we should review the value of the contribution of the Survey, and Australian Geological Surveys in general, to the exploration industry. Most geological surveys in Europe and North America had their origins in the first half of the 19th Century when the burgeoning Industrial Revolution was demanding the identification of new sources of coal and iron ore. Australia, as a young nation, essentially dependent on an agricultural and pastoral industry, and with already discovered vast coal resources in Eastern Australia, had, no great need to explore for new mineral resources. However, with the discovery of gold in 1851, the mineral potential of the country became apparent to the whole world and the first Geological Survey in Australia was set up in 1852 in Victoria under A.R.C. Selwyn. After a number of false starts all Australian States had an established Geological Survey by 1900. It is hard to assess the contemporary value of the early work of the Geological Surveys with respect to exploration, almost all major mineral discoveries were made by prospectors and most mining companies had little time for geologists - although the Chamber of Mines in Western Australia in 1910, did recommend that the Geological survey be granted an additional ten thousand pounds over two years to map all existing goldfields and the country between them, and produce a reconnaissance map of the area east of a line between Wiluna and Edjudina as far as the South Australian border!

Jan 1, 1988

By Walker E. R

IN the early age of steel it was made hy what is known as the cementation proeess, in which wrought iron was embedded in charcoal and heated in a mufflc furnace to a tcmperature of approximately 1100° C. for varying lengths of time, the length of time depending upon the amount of carbon (or better known in thosedays as the degree of hardness) required in the finished product.By this process the resultant product obtained was not of uniform quality, and because of this uncertainty of quality Huntsman was induced, in the year 1740, to introduee what is known as the crucible process.This process consisted of cutting into small pieces the product of the cementation process, placing these pieces in a crucible, and melting them down with the aid of a eoke-fired furnace, after which the molten metal was cast into suitahly shaped ingots, from which could be hammered any desired shape.A section of crucible furnace is shown in Fig. 1. By this means a product, very uniform in character, was produced.The process is still in use, but, owing to its high operating cost, it is mostly eonfined to the production of very high-grade carhon and alloy steels. Its position to-day as a producer of these high-grade steels is, however, being very seriously challenged by the electric process.It was owing to the excessive cost of crucible steels and the need of producing a steel in commercial quantities and at a reasonable cost, that led Sir Henry Bessemer to introduce what is known as the Bessemer process.

Jan 1, 1930

Coal is a very versatile resource, having variable characteristics and having potential for a wide variety of mar- kets. Australia has extensive deposits of black coal, although they are concentrated mainly in Eastern Australia. Assessments of the currently known reserves are related to the qualities of these reserves. Markets available to black coal fall into the broad groupings of metallurgical, fuel, conversion and miscellaneous markets and the requirements of these markets are related to coal characteristics. Market trends in Australia and on the export market are discussed and projected forward. By the end of this century Australian consumption of black coal could well be 100 million tonnes per annum, and, in the absence of any export restriction, a similar amount is likely to be exported. Currently defined black coal resources in Australia will last at least 600 years at these projected rates of consumption. Although the position appears satisfactory in considering the projected life of the black coal resources, there is a serious lack of detailed information on reserves, mining and preparation yields, quality and possible environmental restrictions. Action is required on three parallel courses: (1) a consistent, systematic and extensive survey of current coal resources in Australia, (2) accelerated exploration activity to define poorly prospected and potential areas, and (3) regular updating and extension of the knowledge of Australia's coal resources. This information would be of tremendous assistance for the formulation of a national energy policy on coal.

Jan 1, 1975

By Brown D. N, Troth D. A

Large blast furnaces demand high standards of preparation of feed materials which must meet tight specifications of chemical and physical quality. Measurement of these factors must be expeditious but the nature of the coke, sinter, ores and fluxes and the large tonnages involved requires substantial mechanical sampling plant. The equipment, its operations, and its problems, associated with the 5000 t.p.d. No.5 blast furnace at Australian Iron and Steel Pty. Ltd., Port Kembla, are described and the efficacy of chemical blending achieved in the ore blending yards and sintering operation, is reported.

Jan 1, 1976

The need to schedule ore production to make maximum use of the strength gained by cem- ented fill during curing is discussed, to show how cement content and hence fill cost can be kept down for any particular operation. Results from laboratory testwork on Isa Mine fill conducted by the author while employed by Mount Isa Mines Limited form the basis of the Discussion

Jan 1, 1973

By S Williams, N McBride

The aim of these analyses was to utilise the latest available production information for the Wandoo operation to determine the optimal blasting parameters, costing information and predicted results (fragmentation, muckpile shape and vibration). Much of the data used as input was made available from the information gathered during the excavation of the test pits during 1995. As with any æplanning stageÆ analyses, many assumptions were required to fill gaps in the available data. The calibration of computer blasting models was conducted using data from the last of the test pit blasts (this blast was carried out in material that closely resembled rock expected to constitute the bulk of the base case design pit). This calibration was refined using observation and experience based judgements to extend the accuracy of the predictions as far as possible. All the simulations were performed assuming that the blastholes will be wet (as instructed by BGM). This has consequently determined that the appropriate explosive for the simulations and the actual blasting will be a pumped emulsion/ANFO blend. The following blast design parameters were derived by determining a likely range of powder factor (from other similar scale gold mines) with a median value of 0.62 kg/m 3 being the powder factor arrived at through the field optimisation process conducted during the test pit excavation. The total swell/displacement percentage (volume after blast/volume before blast) largely determines the diggability of a well fragmented muckpile. Consequently where fragmentation is good any reduction of total swell will probably reduce diggabilty. Any reduction of diggability can and should be traded off against increased gold recovery. In most gold mines, diggabilty will be substantially compromised at the balance which produces the most profit. When these considerations are combined with the cost to drill and blast material, processing costs and the achievement of æacceptableÆ diggibility, the analysis becomes extremely complex and qualitative. Many trends are evident including:the relationship between powder factor (for each blast design) and maximum forward displacement (throw), see Figure 1; and the relationship between powder factor (for each blast design) and drill and blast cost per BCM, see Figure 2. The following blast designs are matched to each of three ore-tonnage alternatives (as supplied by BGM) (Table 1). They are all based on powder factor of 0.62 kg/BCM and are considered optimum from a mining æpoint of viewÆ. The costing of each design includes drilling, explosives and labour cost to load, stem and tie-in holes. Using the available rock data and relying heavily on the wall exposures in the test pit(s), it is the opinion of the author that between 20 per cent to 40 per cent of the final walls excavated in the Wandoo pit would be likely to have the angle between the dominant foliation and the wall plane that is well suited to presplitting and be cost-effectively served by presplit technique. The drilling cost for 125 mm blasthole is about $11.40 per drilled metre and the cost of 40 mm presplit explosive is about $140 per 25 kg (17 metre) case. This implies that the cost to drill and blast presplit on the above parameters would be about $10.90 per square metre of presplit face. The remaining wall area would be most cost-effectively delineated using modified production blasting techniques. This requires the use of modified parameters such as smaller hole diameters, smaller spacing/ burden, higher powder factor, free face firing, less rows per blast and longer delays. These altered blast parameters would usually be applied uniformly across the entire blast fired adjacent to the wall and this ætrimÆ blast would relieve burden away from the wall, into the pit. In simplest terms, this method relies upon maximised burden relief to minimise blast energy applied to the wall. It is only applicable where the material to be blasted is waste since the throw achieved is inconsistent with ore dilution control. The largest charge weight per hole for these analyses is 360 kg and the nearest domestic structure to the proposed Wandoo pit is about 6100 metres distant. From these parameters and assuming a worst case example of rock controlled site factor, the predicted ground vibration is 0.5 mm/sec that is about five per cent of the lower limit set down in AS 2187 part two (1993). This suggests that for the current location of neighbours, ground vibration will not be an issue for the Wandoo operation.

Jan 1, 1999

By M Norbert, P Mok

The mainline running tunnels for Legacy Way comprise of two-lane tunnel boring machines (TBM) driven tunnels. The length of the TBM tunnel section is approximately 4.2 km. The TBMs employed are double shield TBMs. Typical support to the segment ring while advancing a double shield TBM comprises of filling the excavated annulus between the ground and the segmental lining by injecting pea gravel, followed with primary grouting to fill between the pea gravel some distance behind the excavated face. The methodology adopted for the Legacy Way project, however, did not follow this typical approach, instead, two component grouting of the annulus was carried out.Where the annulus is typically filled with pea gravel, support is provided to the segment ring very close to the end of the tail shield, whereas in the case of two component grout this is not practical as the risk of grouting in the tail shield is high. The staging of the two component grout injection, the grout early age strength properties become key issues in ensuring that the segment ring leaving the TBM tail shield is stable and can support the necessary external loads.Two-component grout is a grout with two components, cementitious grout (component A) and accelerator (component B), commonly adopted for earth pressure balance (EPB) TBM. The grout reaches its thixotropic state in a matter of seconds providing initial support for the segment rings. Manual injection of two component grout to fill the bore annulus was carried out in stages leaving a portion of the segment rings unsupported. Ring stability during TBM advance was provided by a combination of ram thrust and the segment circumferential joint shear connectors.This paper outlines the design considerations such as rock load derivation by probabilistic analysis carried out utilising the software JBlock, 3D finite element analyses using the software Strand7 for ring stability and the testing and back analysis of the shear connector load bearing behaviour. In particular, the actual available capacity of the shear connectors against their published capacity by supplier was discussed.CITATION:Mok, P and Norbert, M, 2014. Tunnel boring machine excavation stability – double shield tunnel boring machine advance with partially grouted annulus, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 51–62 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By F Sahlström, E M. Jolis, V R Troll, E Jonsson, K Högdahl, C Harris

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Bastnäs-type magnetite-skarn-hosted rare earth element (REE) mineralisations are located in the Palaeoproterozoic Bergslagen ore province, central Sweden, and occur along a ca 100 km long belt of 1.90–1.87 Ga metavolcanosedimentary rocks. Ten different Bastnäs-type deposits have been sampled in order to assess the origin of ore-forming fluids in these systems. Magnetite and quartz have d18O values ranging from -2.3 to +1.1‰ and +7.2 to +8.3‰ respectively. Mineralised carbonates have d18O values between +5.8 and +7.2‰ and d13C values between -5.4 and -3.3‰. Temperature calculations based on the O-isotope composition of mineral pairs, combined with available fluid inclusion data, suggest primary mineralisation at ca 650–400°C. For these temperatures, calculated equilibrium fluids have d18O values that range from those typical of magmatic fluids (+6 to +8‰) to lower values (down to +3‰). Variation in carbonate O and C isotope data are consistent with interaction between local Palaeoproterozoic carbonate rocks (d18O = +12.5 to +19.6‰ and d13C = -1.8 to +1.7‰) and fluids of a magmatic origin. It is suggested that the Bastnäs-type REE-magnetite mineralisations formed as a result of reactions between local carbonate units and high-temperature, magmatic-dominated hydrothermal fluids during 1.90–1.87 Ga (Svecofennian) syn-volcanic activity.CITATION:Sahlström, F, Jonsson, E, Högdahl, K, Harris, C, Troll, V R and Jolis, E M, 2015. O and C isotope study of Bastnäs-type rare earth element mineralisation, Bergslagen, Sweden, in Proceedings PACRIM 2015 Congress, pp 439–444 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Black LP, Law SR, Oversby BS, Mackenzie DE, Wyborn D

Three volcanic sequences of different ages occur close together in the Burdekin Falls area, southeast of Charters Towers in northeastern Queensland. The oldest is equated with the Cambro-Ordovician Mt Windsor Volcanics, and consists mostly of strongly deformed, regionally metamorphosed rhyolitic lava and minor feldspathic to quartzose sandstone. This unit is overlain by folded but unmetamorphosed Upper Devonian-Lower Carboniferous volcanics (DCv) of the lowermost Drummond Basin sequence. The primary volcanic facies of (DCv) principally comprises andesitic and rhyolitic lavas, and dacitic ignimbrites. Similar volcanics are widespread in the lowest formations of the Drummond Basin sequence elsewhere, and dominate that sequence east of the Anakie Inlier. The youngest volcanic sequence is Late Carboniferous and composed of lower, more deformed, compositionally diverse ignimbrites, lavas and conglomerates, overlain by generally less deformed rhyolitic ignimbrite sheets. The upper part is equated with the Bulgonunna Volcanics which extend 90km south to the Mt Coolon area. The Burdekin Falls area contains an ignimbrite stratigraphy different from that in the south. However, one of the most voluminous ignimbrites (Locharwood Rhyolite) in the southern stratigraphy is also present in the north, enabling the two to be correlated.Each of the three volcanic sequences reflects proximity to eruptive sources. Both the volcanics at the base of the Drummond Basin sequence and the Late Carboniferous volcanics are largely the products of subaerial eruptions. The former were erupted from several intermediate-composition volcanoes, and the latter from multiple-vent silicic calderas. All three sequences are considered to be prospective for precious and/or base metal mineralisation. Polymetallic massive sulphide deposits occur in the Mt Windsor Volcanics farther west, and many epithermal gold prospects and mines are hosted by the volcanics at the base of the Drummond Basin, especially east of the Anakie Inlier. The Late Carboniferous volcanic sequence is deeply eroded, and co-magmatic high-level plutons are widely exposed; this sequence may therefore be more prospective for deeper-than-epithermal mineral deposits.

Jan 1, 1990

Milling operations at Misima Mine are discussed, with specific reference to the application of energy and cost saving concepts. Design stage innovations and post-commissioning developments are covered. General operational problems are described with specific reference to problems associated with operating in a remote location.

Jan 1, 1994

By W Kendall

Ore sorting has the potential to reduce the feed to wet plants and in the case of complex orebodies that can significantly reduce the water, energy and reagent consumptions and resulting operating costs for the project. The application of ore sorters has sparked renewed interest and application in the precious and base metals mining industry in recent years as a result of the continuing development of new sensing technology and very fast information processing that is making ore sorters applicable to a much wider range of ores and larger scale operations. The application of ore sorters involves a range of trade-off decisions that have economic impact upon the benefits of ores sorting to the project under consideration. This paper will present some typical trade offs to be considered and their impact in a particular project setting. CITATION: Kendall, W, 2018. How economics drive the application of ore sorting, in Proceedings Complex Orebodies Conference 2018, pp 24–27 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By P N. Duan, Z G. Liu, M S. Chu, X X. Xue, B Liu, G J. Cheng, T Jiang, J X. Liu

High-chromium vanadium-titanium magnetite has not been exploited and made full use of on a large scale so far due to the immature utilisation technology and the reality that the utilisation efficiency of valuable metals still urgently needs to be improved. In the present paper, the isothermal reduction kinetics and mechanism of high-chromium vanadium-titanium pellets were studied at 800–1100°C. The mineral composition transformation of pellets before and after reduction was analysed by means of X-ray diffraction (XRD), and the microstructures were examined by scanning electron microscope (SEM) equipped with energy dispersive X-ray (EDX) to reveal the elemental distributions. The effect of reduction temperature on the volumetric swelling degree and cold crushing strength was also studied. It was found that reduction temperature has a large effect on the reduction rate of pellets, and the increase in reduction rate is more obvious in the range 1000–1100°C than 800–1000°C. The volumetric swelling degree of pellets increased with increasing reduction temperature, while the cold crushing strength decreased. The transformation of mineral species can be expressed as Fe2O3 ? Fe3O4 ? FeO ? Fe, Fe2O3·3TiO2 ? Fe3O4· (2FeO·TiO2 ) ? 2FeO· TiO2 ? FeO·TiO2, (Fe0.6Cr0.4)2O3 ? FeO· Cr2O3 ? Cr2O3 , and Fe2O3· VO/V2O3 ? VO. The apparent activation energy of the reduction reaction was calculated to be 44.3 kJ/mol, and the reduction rate is controlled by the combined effect of interfacial chemical reaction and gas diffusion through the porous product layer. The rate controlling steps were further studied by calculating the resistance percentages. The interfacial chemical reaction was found to be predominant in the initial reduction stage, with the percentage effect of gas diffusion through the porous product layer gradually increasing during reduction.CITATION:Cheng, G J, Xue, X X, Liu, J X, Liu, Z G, Chu, M S, Jiang, T, Liu, B and Duan, P N, 2015. Reduction kinetics and mechanism of pellets prepared from high-chromium vanadium-titanium magnetite concentrate, in Proceedings Iron Ore 2015, pp 349–358 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By G Chitombo

Mass mining methods have become the mining industry’s preferred way of extracting most of the world’s most important metal and mineral commodities. Given the rapidly increasing global demand for commodities, the requirement to increase the contribution of some of these (eg copper and gold) from underground sources also continues to grow. In the case of copper this contribution is needed by a number of major producers to supplement production from their ageing deep open pits. Satisfying this increased demand will require the design, construction and operation of more effective, higher capacity and larger scale mines which, in turn, will require enhanced mass underground mining techniques such as block caving (BC), panel caving (PC) and sublevel caving (SLC).It is now widely accepted that future discoveries of orebodies, which will be developed using these methods, are almost certainly to be much deeper than the deposits presently being mined in this way and made more challenging because of the likelihood that the associated grades may be much lower than currently mined. The design and mining of future large-scale cave mines (supercaves) will become crucial in order to extract full value from such deposits. An essential prerequisite of this will be a much improved knowledge of the deposit, ie Total Deposit Knowledge. In this context, Total Deposit Knowledge is the characterisation of the ore deposit and its surrounds at all scales and includes; rock type (lithology), the spatial orientation of a range of geological features or discontinuities, rock mass fabric knowledge, metal grade and distribution data, geometallurgical data (including alteration), geo-hydrology, permeability and porosity. This is the information that will be used, as now, to delineate geological and geotechnical domains and construct models, but with outcomes superior to those presently available. From this information better-informed feasibility study design decisions and performance predictions must be made. In summary more geological information and analysis is required and this needs to be aligned to potential mining and processing requirements much earlier in the project than commonly occurs.

Aug 22, 2011

By J P. Sykes, A Trench

"The common-held view of the future of copper mining is one of declining quality of mineral resources and increasingly limited long-term development options. This decline, in turn, is viewed as inevitably leading to increasing economic, socio-political and environmental costs. As a result, new technologies and innovations will be required to mitigate cost escalation. The future is therefore typically summarised as a battle of a ‘below-ground’ declining quality asset base pushing costs upward versus ‘above-ground’ technology and innovation driving costs downward. The role that high quality new mineral discoveries could play in mitigating industry cost pressures is typically understated, if considered at all. New high quality discoveries can be mined at lower cost than existing assets and potentially if discovered in the right locations within a more amenable contemporary environmental and socio-political setting. Such deposits, once discovered, would improve the overall quality of the industry asset base, as well as benefitting their owners substantially through higher margins. However, to target new high quality deposits explorers need some understanding of the nature of high quality copper mines in the long-term future. Conventional scientific and economic techniques for analysing the future of copper supply, generally by studying the project pipeline, ignore as yet undiscovered resources and also struggle to fully incorporate the multiple internal and external factors that could impact upon copper mining practices in the future.Scenario analysis is specifically designed to consider multiple factors interacting in the future, and is thus more creative than simply looking at the visible project pipeline. The use of scenarios is therefore potentially capable of providing insight into aspects of the future of copper mining about which little is currently known or that remains considerably uncertain. In this study, the Oxford University Scenarios methodology was employed to analyse different plausible futures for copper mining and the consequent implications for exploration targeting strategies. The scenario analysis highlights two key dimensions or axes that serve to map out potential industry futures: firstly the technical and economic optimisation of the existing industry; and secondly the generation of new prospects or ‘search space’ for the copper industry. These two axes in turn frame four different scenarios for the future of the copper mining industry. These copper mining scenarios are then compared to the 20 largest existing copper mines and projects, and their owners, to determine if any represent an appropriately robust exploration targeting proxy: none do. The paper therefore concludes that efforts by industry are required to generate mine concepts that would be viable across all scenarios, and thus act also as exploration targeting proxies. In the interim, companies will have to seek to build portfolios that create an overall robust asset base, out of individually less robust assets. Failure to do this implies that consequential, irreversible strategic decisions lie ahead for the copper mining industry, which may be a threat to both incumbents and the very industry itself. This situation makes strategic exploration targeting in the copper industry very difficult.CITATION:Sykes, J P and Trench, A, 2016. Using scenarios to investigate the long-term future of copper mining and guide exploration targeting strategies, in Proceedings International Mine Management Conference, pp 265-290 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 22, 2016

Minerals and Metals Group (MMG) Century mine (Century) is a large open-cut mine in northwest Queensland approximately 2.5 km long, 1.5 km wide and 240 m deep, with an ultimate pit depth of 320 m. In 2009, the mine experienced three failures which began as small failures, and progressively developed into significant multi-batter failures. The incidents were managed by a combination of analysis, redesign and practical management to achieve positive outcomes for the mine. On the south wall of the mine, a series of batter-scale wedge failures occurred in December 2007. Analysis of structure orientations and design changes aimed to minimise the risk of failure extending over multiple batters, while accepting a risk of further small-scale failures. Design changes were constrained by a culturally sensitive area (CSA) located south of the wall. As mining progressed, shallow wedge failures developed over multiple batters and cracks were observed 60m back from the pit crest, indicating that a large-scale wedge failure was developing. Movement increased in January 2009 as a result of significant rainfall. After considering several design options, the area was stabilised by a cut-back of the wall. Two multi-batter failures also occurred on the north wall as mining progressed through a structurally complex area. Both north wall failures began as small failures that progressively developed, and required a redesign of the wall below as well as practical management of safety aspects. The complex structural geology was difficult to predict ahead of mining, and required geotechnical input into design changes as mining progressed. All three failures potentially had significant impact for ore recovery, and were managed by a combination of analysis, redesign and operational management have resulted to achieve positive outcomes in a challenging mining environment.

May 1, 2010

THIS paper is not intended to be a detailed description of the lead, smelting plant at Cockle Creek, as this has been covered in previous papers for the Institute in 1918, Proceedings No. 31, by other members of the staff; but the idea is to give some of the practices and conditions peculiar to these works, also to give some experiments carried out and the conclusions arrived at. Unfortunately, owing to the closing down of the smelting and refinery plant at these works, sone of the experiments could not be carried to a more definite and commercial basis, but they are given in the hope that they may be of interest to members, and may perhaps suggest further thought along the lines indicated.ROASTING AND SINTERINGThe greater part of the ore treated at these works came from the Central mine, Broken Hill, but, in addition, a large quantity was purchased from other parts of New South Wales and from Tasmania. This purchased ore was seldom received in the form of a concentrate, but initially in its crude state, and therefore had to be crushed. The crushing was done in a Krupp mill, and the ore then added to the roasting mixture. This addition of crude ore was one of the main...

Jan 1, 1923