Search Documents

By G K. N Subasinghe

Metallurgists operating Knelson Concentrators (KC) often rely on manufacturerÆs recommendations for selecting operating parameters, such as fluidising water flow rate and cycle time. Recent studies have shown that these parameters are not only dependent on the machine parameters but also on the feed characteristics, such as size distribution of the gold and gangue particles and the composition of its constituent minerals. It is known that a particle entering a KC initially traverses a circular path within the bowl. For a particle to maintain a given orbit, the required centripetal force must be supplied by external means. It has been argued that this centripetal force, which is dependent on the mass of the particle, its radial position and the rotational speed of the bowl, is provided by the fluid drag force created by inwardly moving fluidising water and the BagnoldÆs force created by the particle/particle collisions. Depending on the fluidising water flow rate, one of two situations can occur where the porosity of the bed increases or decreases, which influences the amount of material retained within the bowl. The amount of material of a given size and density retained in the bowl is thus dependent on the extent of the centripetal force provided. Based on the above concept, a criterion that can be used to predict the amount of material recovered in the bowl has been derived and validated by experimental data. It may also be construed that this criterion demarcates the transition of the bed from a packed-bed state to a fluidised state. By identifying the transition values for the different constituent mineral particles in the feed, it is possible to estimate the optimal fluidising water flow rate that would maximise gold recovery while minimising gangue recovery. In addition, the kinetics of gangue displacement by incoming heavy mineral particles were also studied using synthetic mineral mixtures. The experimental data suggests that this process follows first order kinetics and that the build-up of heavy mineral reaches a maximum. A model has been proposed to predict the optimal batch cycle time for a KC in terms of the feed characteristics and machine operating parameters.

Jan 1, 2006

By B M. H Sharp, R P. Hide, S P. Devine

Uncertainty and debate currently pervade the mining industry in New Zealand. The operational uncertainties, whether external (eg gold prices, the exchange rate), or internal (eg coal expansion difficulties), are large. In addition, many wider factors which influence mining are in a state of flux. State Coal Mines, the operating branch of the Mines Division of the Ministry of Energy I may be made a state corporation, with the remaining Mines Division functions being revamped. The agencies administering environmental legislation are to be restructured. Mining legislation amendments have been proposed and then dropped, and the area is now to be reviewed (The Press, 31 July 1985). Some mining licences have been withdrawn, and become the subject of heated debate in the community (The Press, 19 July 1985, and subsequent letters to the editor).

Jan 1, 1985

By T Roberts, S Talu

Steel wire weld mesh is a common industry standard surface support used in underground mining, traditionally installed with mining drills during the bolting cycle. As underground mining depth and stress increase, mining methods and their sequences at these depths place challenges on conventional surface support options. These challenges have provided a need for high capacity surface support options that improve development efficiency, reduce the need for secondary ground support installation and is easily installed with current mining equipment. A 5m2 mesh testing machine was built, suspending a 9500kg concrete slab, designed with multiple hold down points to test varying bolting patterns. Mesh load and displacement is accurately measured using a data acquisition system which pushes against the restrained mesh module with an available 200kN load and 1200mm displacement capacity. A testing program comparing conventional surface support, straps and combinations of both were tested for baseline results. New module designs incorporating existing mesh types and new design concepts were manufactured to allow for single pass installation during a bolting cycle. Nine mesh types, mesh/strap combinations and new mesh module designs were compared using the same test method. Based on these results, two high capacity mesh module types are produced. This paper will detail the test program, load and displacement results and underground mesh module performance, describing the two high capacity mesh modules function within the development cycle and manual handling. CITATION:Roberts, T, Talu, S and Wang, Y, 2018. Design and testing of high capacity surface support, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 303–322 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

Reduction of Iron Content from Silica by Gravitational Processes In this research work, it was attempted to reduce the iron contents (Fe2O3) in silica sample which was provided from Shenin silica mine using gravitational processes including jig machine, multi gravity separator (MGS), shaking table and spiral. The silica sample contains 93.75 per cent SiO2, 0.44 per cent Fe2O3, 2.78 per cent Al2O3, and 0.08 per cent TiO2 and the Fe2O3 has to be reduced to about 0.1 per cent or less than 0.02 per cent. Mineralogical studies and XRD analysis indicated the presence of haematite, pyrite and goethite as the major iron impurity phases. Mineralogical studies of polished and thin sections yielded that the degree of freedom of silica is more than 80 per cent in the range of -300 +212 mm. After elimination of fine particles, at first nine tests were carried out on crusher product (in two size fractions), wet rod mil product and scrubber product by means of Jig Machine. The best results were obtained with about 0.15 per cent Fe2O3 on rod mill and scrubber product which was not desirable. Thereafter 7 tests were carried out using shaking table; the best results were obtained with about 0.14 per cent Fe2O3 on rod mill and scrubber product which was not desirable. MGS showed the worst result in order to iron removal from silica which was not desirable. Finally 9 testes were carried out using spiral whish is the best gravitational separator for elimination of iron impurities from silica. The best result of spiral tests were achieved on scrubber product. In this test concentrate weight percent and its Fe2O3 grade were 82.32 per cent and 0.085 per cent respectively. Finally a test was carried out using 2 stages of spiral in order to develop flow sheet. In this test concentrate weight percent and its Fe2O3 grade were 78.8 per cent and 0.1 per cent respectively. This product can be used to produce float (clear flat) glass.

Sep 13, 2010

By L I. Rozman

"There have always been development projects that fall short of expectations. In the last decade, we have seen more than the usual number of mining and oil/gas development projects taking significantly longer to develop and costing materially more than expected. The recent resource-equity market slump proves that investors are now far more cautious about investing new capital in the mineral and petroleum resources sector.What have we learned since 2005? Why have projects missed their targets? Why do investors often feel misled?Valuation of a project and the estimation of value is a more complex process than the evaluation of the merits of project development. The merit of project development can be clear from a prefeasibility evaluation, but this is no reason to skip the rigour of a feasibility study. The valuation of any project that is developed with any added risk should be discounted for this added risk.The development of a project impacts on other stakeholders, and the indirect cost of these impacts can have material implications for the cost structure, time and ultimate valuation of the project for its financial backers. The development of new projects (and thereby supply) can also have an impact on commodity prices, and therefore an impact on returns for financial backers.This paper will provide commentary on the author’s experiences and observations as a project developer and operator for 25 years, before becoming a project financier a decade ago.CITATION:Rozman, L I, 2016. Project evaluation and valuation – an investor’s golden rule, in Proceedings Project Evaluation 2016, pp 31–36 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

By Y Cui, G Cao, H Zong, J Zheng, J Wang, S Yue, J Zhao, B Li

The iron (Fe) concentration in nickel slag is high, making its recovery and utilisation a hot and challenging topic. In the nickel smelting process, using CaO instead of SiO2 to adjust slag’s composition, and then directly reducing Fe from the output of molten slag is a more feasible method in practice for Fe recovery in nickel slag. The adjustment of slag’s composition in the nickel smelting process will have an impact on the distribution of impurity elements such as Pb, Zn, and As. In this paper, the slag adjustment of nickel smelting process was carried out with the oxygen-enriched topblowing system. The distribution of impurity elements in the smelting products with each composition slag was conducted by using thermodynamic software. Experimental verification was performed with rich oxygen top-blowing, and the distribution characteristics of impurity elements in the smelting products were characterised to explore the differences in mineral phases of impurity elements with each smelting conditions, elucidating the distribution patterns of Pb, Zn, and As in each phase. The results indicate that after slag adjustment, impurity elements are more easily to volatilisation and removal into the gas, reducing their total concentration in slag and matte. In the slag, the existence form of Pb, Zn is changed from silicate to ferrate, and As is changed from arsenate to low-valent arsenic oxide. It is easier to decompose the impurity-containing mineral phase and remove the impurity elements in the subsequent iron extraction process.

Jun 19, 2024

By C Vejrazka

Northparkes is located 27 km north of the township of Parkes in central New South Wales, Australia. The operations consist of underground block cave mines and an ore processing plant that produces high-grade copper and gold concentrate. Production is currently sourced from the E48 Lift 1 block cave mine and open cut stockpiles. Mining commenced at Northparkes in 1994 as an open cut operation. Underground block cave mining began in 1997. Northparkes was the first mine in Australia to use the highly efficient block cave mining method, which relies on gravity and natural rock stresses to fragment the ore.The occurrence of air blasts is one of the principal mining hazards in block caving operations between the time of first undercutting and breakthrough of the cave to surface. As such, it needs to be managed continuously, and risk assessments need to be reviewed on a regular basis for applicability to changing conditions. Unfortunately, there is little literature on how to practically approach air blast risk assessments in a way that can be incorporated in the day-to-day operation of a mine. Previous methods of assessing air blast risk were tedious and results were often unrepeatable.With the extension of the E48 Lift 1 extraction level, it was necessary to assess the air blast risk for the extension drives and develop operational guidelines for production from the extension. A review of the methodology for assessing air blast risks revealed substantial improvement opportunities.This paper outlines the principles used for air blast risk assessments at Northparkes Mines and the methodology employed to achieve efficient, repeatable and auditable results.CITATION:Vejrazka, C, 2016. Northparkes Mines’ current air blast risk assessment practices for block caving operations, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 257–264 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By J deVries, A Broodryk, P Kyselica, K McLean

Gwalia gold mine is located close to the town of Leonora in the Goldfields region of Western Australia, some 830 km from Perth. The mine is wholly owned by St Barbara Ltd, an Australian Securities Exchange listed gold producer and explorer. The Gwalia mine is a deep, all-trucking mine and is serviced by a 10 km long decline from surface. Mining is currently 1540 m below surface. Reserves extend to 1820 m below surface and are open at depth. The mine produces in excess of 200 koz of gold per annum.The Leonora area is hot and arid, with a mean annual rainfall of 230 mm and a 95 per cent mean daily maximum temperature of 20.3°C wet-bulb and 35.6°C dry-bulb.The primary ventilation system comprises a 490 kg/s surface exhaust fan, which draws air down a parallel intake system consisting of the decline, and a dedicated fresh-air intake system extending to the bottom of the production zone. Cooling is provided via a surface bulk air cooler serviced by an ammonia refrigeration plant that delivers 150 kg/s of chilled water to the bulk air cooler.The refrigeration plant and bulk air cooler were installed in 2008. The design allows cooling to be increased over time by installing an additional refrigeration plant in a lead lag configuration with the current refrigeration plant when required.Since 2008, expansion and increased depth reached a point where the underground heat load exceeded the installed capacity of the existing 4.0 megawatt rated (MWR) refrigeration plant. In order to maintain the mine design conditions underground, upgrading of the existing refrigeration system was required to bring the cooling capacity to 7.5 MWR.Two expansion options were considered: the addition of an ammonia vapour-compression refrigeration machine similar to the existing one or a lithium bromide absorption refrigeration system using waste heat from the site power station. The original design and layout of equipment on-site meant that either could be used, allowing an assessment of the merits of both when additional cooling was required.The decision was made to install a lithium bromide absorption system on the lead side of the existing ammonia refrigeration plant. This arrangement provides considerable economic benefits, including reductions in site-generated electrical power, generator fuel consumption and carbon dioxide emissions.This paper details the planning, design, installation and commissioning of the absorption chillers.CITATION:Broodryk, A, deVries, J, Kyselica, P and McLean, K, 2015. The design, installation and commissioning of an absorption refrigeration system at Gwalia gold mine in Western Australia, in Proceedings The Australian Mine Ventilation Conference, pp 193–200 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By D Kay, M Lovitt

Mass Blasts are generally required at the completion of longhole stoping cycles to maximise the recovery of ore from a specific orebody. During the course of mining, the practice is to leave pillars of ore to support the opening left by extracted ore and to mitigate stresses from working areas of the stope. These pillars usually contain ore that has been included in the resource evaluation and is highly valuable to the mining operation. Due to their stressed nature, the removal of pillars by conventional blasting techniques, through small blasts, can result in pillars being reduced beyond their critical size and ultimately failing, rendering the ore unrecoverable. The AurionGold Kanowna Belle Gold Mine operates a Mine to Mill philosophy. This philosopy requires the fine tuning of blasting to provide the best possibe ore feed at the highest grade for mill productivity. This means that ore to the mill must be well fragmented from blasting that provides high extraction rates from draw points, with minimal dilution from overbreak or fall off, and sized to maximise SAG mill throughput. The AT04 Mass Blast contained significant ore reserves which were required to meet gold production targets. KBGB needed the AT04 Mass Blast to perform as well as if not better than conventional stope blasts to maintain mill production. This paper describes the circumstances, planning philosophy, techniques, including the use of Electronic Initiation Systems and Bulk Emulsion Explosives, and results that provided a highly successful outcome.

Jan 1, 2002

By Lee H. G, Li H, Hayes P

Slag from the smelting of lead can contain up to 20 per cent zinc as an oxide. An understanding of the lead smelting process and of the subsequent fuming process for the recovery of zinc is enhanced by a knowledge of the activity coefficient behaviour of zinc oxide in smelting slags. The literature presents a wide range of contradictory values. This paper critically reviews the published data and outlines new measurements being made by the authors. A consistent set of zinc oxide activity coefficient data is presented for liquid slags within the ZnO-'FeO'-CaO-A1203-SiO2 system, through a combination of present and previous measurements.

Jan 1, 1993

By G Brooks

The control of phosphorus in steelmaking is one of the famous challenges of pyrometallurgy. It is well established that highly basic slags, the presence of FeO in the slag and lower temperatures (less than 1650°C) are favourable for phosphorous removal. The thermodynamics of this reaction have been extensively studied under laboratory conditions and the general trends confirmed through industrial trials. However, in general, phosphorus slag/metal distributions measured in industry are far from equilibrium and quite specific to the oxygen steelmaking technology being used. This variability was quantified by Urban, Weinberg and Cappel (2015), who found that the phosphorus partition ratio measured in plants varied with blowing practice, stirring intensity and even converter life. Some recent kinetic studies by Gu, Dogan and Coley (2017) have shown how the kinetics of these reactions vary with FeO content and dissolved sulfur at the droplet scale. A global kinetic model by Rout et al (2018) provides meaningful predictions of where dephosphorisation occurs in an industrial basic oxygen furnace (BOF) and some recent heat transfer modelling by Madhavan et al (2021, 2022) implies that temperature difference between droplets and slag has a role to play in explaining why equilibrium is not achieved. This paper will review the current state of knowledge and provide suggestions on predicting phosphorous removal for industrial operations and how greater removal could be achieved.

Jun 19, 2024

By N Akizawa, A Tamura, S Arai

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Reaction products between high-temperature hydrothermal solution/uppermost mantle peridotite or lowermost crustal gabbro have been reported along Wadi Fizh of the northern Oman ophiolite; they are named as ‘mantle diopsidite’ and ‘crustal diopsidite’ respectively (Figure 1).The mantle diopsidite contains Cr-rich minerals like chromite, Cr-rich diopside (<2.5 wt per cent Cr2O3) and Cr-bearing grossular (<7.0 wt per cent Cr2O3). The chromites are varied in shape in the mantle diopsidite, euhedral to anhedral chromite grains contain globular inclusions of grossular and chlorite, and film-like chromite veinlets branch off from partially dissolved coarse chromite grains. In the crustal diopsidite, fine chromite grains are included in oscillatory-zoned skeletal uvarovite, especially in its high-Cr zones. The uvarovites are rich in rare earth elements (REEs). Direct laser ablation – inductively coupled plasma – mass spectrometer (LA-ICP-MS) analysis of the primary fluid inclusions detected Na, but not K.Our detailed studies of Wadi Fizh diopsidites clarify that the high-temperature hydrothermal solution dissolves chromite grains at the uppermost mantle section and precipitates hydrothermal chromite at the lowermost crust section. In addition, REEs were mobilised in the hydrothermal solution together with Cr. The hydrothermal solution involved in the diopsidite formation is assumed to have been rich in NaCl, and could mobilise appreciable amounts of Cr and REE.CITATION:Akizawa, N, Arai, S and Tamura, A, 2015. Chromium and rare earth elements mobility by sodium-bearing high-temperature hydrothermal solution – an example from mantle diopsidite and crustal diopsidite, in Proceedings PACRIM 2015 Congress, pp 291–296 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

The man in the street (and no doubt most members of the Institute) thinks of wire, if he gives it any thought at all, as a most commonplace commodity. It is an accepted necessity, and like most necessities is taken for granted, unless a shortage in one or other of its multitudinous forms or products causes inconvenience.For many years Australia has ·been a large consumer of wire, particularly for fencing. With the rapid development of secondary industry the demand has increased in both size and character until at the present time much of the wire produced in this country is used as raw material for subsequent manufacturing processes. The call has been of so varied a nature that the Newcastle Wire Mills now turn out a greater variety of wire types than any other single plant in the world.In this paper, the aim is to provide a picture of the manufacturing, properties, and uses of wire. No attempt is made to cover the subject in any detail, as the field is much too broad for anything other than general treatment. Many phases, particularly in regard to manufacturing processes, are, therefore, dealt with cursorily, but it is hoped that the paper will, without delving too deeply into the technical aspects of Wire production, give a general appreciation of:- (a) How steel wire is made. (b) The remarkable physical characteristics obtained by judicious combination of chemical composition, heat treatment, and subsequent cold work. (c) The uses of steel wire.HISTORY.Best known of the early references to wire is that appearing in Exodus, where mention is made of gold wire being used for the sacerdotal robes of Aaron. However, the period in question, about B.O. 1491, is comparatively modern history as far as wire is concerned, for specimens believed to have been made about B.O. 4600 have been found. It is fairly certain that the Egyptians produced iron wire in B.O. 4000. Of particular interest is the

Jan 1, 1947

Through the use of structural analysis programs such as Unwedge and considering the shear strength of applied fibrecrete it can be shown that fibrecrete can provide a higher factor of safety in a ætypicalÆ underground development excavation than standard rock bolts. This paper describes the progression of ground support from an æas requiredÆ component of mining to the use of bolts and surface support as a mandatory requirement. With the mandatory requirement for surface support, fibrecrete has been considered and applied as a secondary feature but simple analysis and practical observations indicate that it may be considered as primary support. The key elements to its implementation are: When is it safe to work under fresh fibrecrete and how do we practically determine this? How much ground support does fibrecrete provide? How can we reduce the cost of fibrecrete? An examination of these questions indicates fibrecrete can be much safer,less expensive and quicker to install than normal ground support elements. This paper explores practical examples from sites where significant benefits have been achieved by mine operators.

Jan 1, 2005

Operating metallurgists spend a significant part of their time running plant trials to compare two or more conditions in order to improve the process, such as a new reagent, flow sheet or piece of equipment. The best way to conduct such a trial is as a paired experiment when testing two conditions (eg 'old' and 'new') or a randomised block design when testing more than two conditions. These experimental designs should always be preferred over alternatives if their requirements can be met, because they block the effect of uncontrolled variables ('covariates') and are the most statistically efficient, ie they will lead to the required level of confidence in the outcome faster than other methods. Sometimes, however, it is not possible to switch condition easily, which is a prime requirement of these methods. In such cases the only option may be to switch condition once only, and compare the process performance before and after the switch. Examples are testing grinding media, large equipment, or long residence time processes such as leach trains or CCD thickeners. This paper considers some data analysis methods to deal with this situation. Modelling with intervention analysis (IA) uses regression models with a dummy variable to indicate the presence or absence of the test condition. IA with a time series model ensures that the residuals are uncorrelated. IA with a process model helps to deal with the problem of covariates. The reference distribution is a method free of any statistical assumptions but is less powerful than the other methods. Cusum charts are a helpful visual aid to interpreting time trends. A combination of these methods can help improve the confidence in the final decision. None are as good as a formal experimental design such as a paired trial.

Jan 1, 2008

By N J. Goodman

The HIsmelt technology was developed and proven in Western Australia (WA) after more than 30 years and several billion dollars of research and development. The HIsmelt technology was transferred to China and is now successfully operating at the Molong plant in Shandong Province, China using WA iron ore fines as the major feedstock. Several more plants are under construction in China, and the technology has been approved by the Chinese Government as an environmentally acceptable alternative to the blast furnace. The unique flexibility of the HIsmelt process offers multiple pathways to decarbonise the production of steel in the near future. These pathways include:  Use of sustainably grown biomass converted to Biochar to replace coal as the reductant.  Pre-reduction of iron ore fines using hydrogen or biomass to direct reduced iron (DRI) powder.  Capture of carbon dioxide from the HIsmelt off gas and geo-sequestration underground. These pathways are highly suitable for the Australian iron ore industry as they utilise:  The large areas of land and long growing season available in Australia for the production of large tonnages of sustainably grown biomass.  Coarse iron ore fines directly without the need for fine grinding and pelletising.  Existing oil, gas and other underground gas reservoirs to store carbon dioxide. The HIsmelt technology will allow Australia to transition from ‘Asia’s quarry’ to Asia’s supplier of low cost, low carbon and high quality metallics that are required to produce ‘green’ steel with net zero carbon dioxide emissions. In addition, HIsmelt pig iron can be converted locally into steel via electricarc or basic-oxygen steelmaking furnaces to supply all of Australia’s demand for green steel.

Nov 8, 2021

By C M. MacRae

The characterisation of high-P iron ores by field emission gun electron probe microanalyser (FEGEPMA) was carried out to determine elemental associations in iron oxides sensus lato and, using this knowledge, to speculate on possible P incorporation mechanisms in goethite. Quantitative data was collected from two goethite-rich bulk ores and results showed that in both samples goethite was the main repository for phosphorus. The P-rich goethite also contained elevated levels of both aluminium and silicon.To understand the mechanism of P incorporation in goethite, high-P grains were located by coarse mapping of polished blocks with the FEG-EPMA. Analysis of element distribution maps collected on the P-rich grains showed that low-P regions within grains were typically associated with low-Al and high-Si, whereas high-P regions were associated with high-Al and low-Si. Based on follow-up quantitative analyses, a coupled substitution mechanism for phosphorus incorporation within goethite was proposed: 2Si4+ = 1P5+ + 1Al3+. Additional quantitative analyses on further examples indicated the mechanism was only valid for Si contents in goethite of <1 wt per cent.Preliminary transmission electron microscope (TEM) studies confirmed the presence of P, Al and Si in goethite.

Jul 11, 2011

By X Dahe

SLon vertical ring and pulsating high gradient magnetic separators possess excellent mineral processing ability and have been widely applied to process oxidised iron ores. SLon centrifugal separators are applied to clean the SLon magnetic concentrate and remove quartz and other gangue minerals associated with a small portion of magnetite.This paper introduces the application of this technology in Hai Nan, Da Hong Shan and An Shan for processing oxidised iron ores.

Jul 11, 2011

By J M. Galvin

History attests to the catastrophic consequences that fire, explosion and contaminated, noxious andirrespirable atmospheres can have for workplace health and safety in underground coal mining. It also confirms that fires and explosions present the greatest risk of partial or total loss of underground mines and equipment and that this risk continues to materialise. The design, implementation, operation and maintenance of the mine ventilation system are core controls for managing the hazards associated with these risks, both for preventing them from materialising and for mitigating their consequences if they do materialise. These are most effective when embedded in a risk management approach.

Oct 12, 2022

By A C. Robertson

World urban expansion puts constraints on the available land surface area of our major cities both for accommodating people as well as providing infrastructure and services whilst at the same time attempting to preserve the remaining natural environment. Whilst consideration is often given to underground planning for private and public transport infrastructure, the author is of the opinion that the current lack of underground planning of our cities that are suitable for underground development will have major long implications when finally the need for underground space planning is critical and ultimately recognised. This paper identifies the need for our city planners to integrate surface planning and underground planning as a ‘total planning solution’ where the city plan incorporates the elements of underground space planning as identified in this paper. Investigations by the author reveal that there are very few cities in the world that actually incorporate underground space planning in their city plans. The author uses the City of Brisbane as a case study for the potential introduction of underground space planning as part of the city plan. Despite efforts by the author to include the planning concept of underground commercial development in the latest Brisbane City Plan 2014 as well as four underground space workshops in Brisbane over the past 20 year through the Australasian Tunnelling Society (ATS), underground space planning for the City of Brisbane, apart from infrastructure projects, is not considered of significance to the City of Brisbane.CITATION:Robertson, A C, 2014. Commercial underground space – planned development for the future, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 513–518 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014