Search Documents

By S Mitchell

Jetcrete Australia Pty Ltd, shotcrete contractor took the initiative in 2008 to discontinue the use of ‘road registerable’ concrete trucks for all underground works in Australia and internationally.The rationale for this decision was basic, safety. Historically these vehicles have been and still are involved in far too many accidents; this obvious trend needs to be addressed by engineering out the root cause of the problem which in this case is suitability for purpose.Road registerable concrete trucks have been widely used for the delivery of concrete in Australian mines for many years prior to and after the inception of wet shotcrete as ‘in cycle’ ground support in underground excavations around 1992. With this inception came a wide interest in the shotcrete process and an influx of new shotcrete contractors, all using road registerable concrete trucks to deliver the large volumes of Shotcrete required for these services and in turn largely increasing the use of these vehicles underground. The road registerable concrete trucks were difficult to control and each trip underground required the operators to maintain good management of the inherent risks. We virtually had no reasonable alternative for the industry and could only encourage the operators to drive with soft controls such as, reducing overall speed to a maximum of 15 km per hour when declining, regardless of the road conditions, coming to a complete halt prior to turning into any sharp corners, remaining in the same gear both inclining and declining.

Mar 21, 2011

The Melanesian Outer Arc, extending from. Papua New Guinea to Fiji, developed as a result of interaction between the Australian and Pacific plates throughout the Tertiary, and the following stages are recognized. ,a, Formation of island arc tholeites above a west facing subduction zone in the Lower Tertiary. fit Emplacement of mainly calcalkaline volcanics above an east facing subduction zone in the Upper Miocene and Pliocene. ontinued east facing subduction coupled with fragmentation of the arc from the Pliocene onward. Alkaline and Mg-rich volcanism occurred in addition to continued calcalkaline activity. Tre Upper Miocene and younger volcanism is into five arc segments on the basis of geographic position and nature of the magmatism. The calcalkaline Bismarck arc extending along northern New Britain and including small islands to the west. The alkaline Tabar to Feni arc, north of New Ireland. The Solomons arc, including Bougainville and the western part of the Solomon slands. Volcanism is largely _.alcalkaline, but Mg-rich varieties occur the Solomon Islands. roe New Hebrides arc, extending from the -astern Outer Islands of the Solomons through Vanuatu. Both calcalkaline and :alkaline volcanics are representeo. alkaline and calcalkaline Fiji arc.

Jan 1, 1987

By H Asche

The proposed Rockwater Power Project is a hydropower development on the Waitaki River in the South Island of New Zealand. The proposed development will have an installed capacity of 250 MW with a peak flow capacity of 260 m3/s. The project commences at Lake Waitaki and extends some 35 km downstream on the north bank to a surface power station at Stonewall. Flow is returned to the Waitaki River via an outfall channel.The tunnelling for the project is through Greywacke, which comprises Permian and Triassic age marine sediments that are well indurated and weakly metamorphosed. The rock mass is jointed and sheared and there are frequent faults, which range up to hundreds of metres in width. Three 12 m diameter tunnel boring machines (TBMs) are proposed to excavate the 35 km long tunnel.The paper describes the development of the tunnel alignment, rock mass classification, design of the support, rock and hydraulic loads, support installation options and construction sequencing.The alternatives of rock bolts and shotcrete and segmental lining were both investigated and are discussed. Support using rock bolts and shotcrete offers the potential of rapid construction with minimum support cost when the ground conditions are good, but delays due to support installation increases with deteriorating ground conditions. In contrast, segmentally lined tunnels offer greater certainty in cycle time with reduced program risk. Both options are described and discussed.The horizontal alignment is affected by the presence of major fault zones, which are either avoided, or pretreated by driving conventional tunnels through in advance of the TBM delivery, topographical constraints with the rugged topography and operational hydraulic constraints. Construction requirements, future power station operation and the minimisation of leakage from the tunnel have all impacted on the vertical alignment.The number and sequencing of TBMs to be used is discussed in terms of program time and risk minimisation.

Mar 8, 2011

By D J. D'Astoli, M D. Goodz

In 1993 a detailed review of drill sample yuuluy was rouxluard through twin and triplet drill holes using open hole, crossover suhreverse circulation (RC) and diamond drill methods. Advances in face-sampling RC methods demanded a further review of the validity and reproducibility of drill sample data. A program was undertaken to drill three RC holes using the latest technology (new face- sampling bits, dust suppressers, cyclones and compressors). Volumetric and mass studies were undertaken to review sample recoveries. Modal analyses on indicator minerals were logged to interpret the relative degree of mineralisation. Ambiguities in the results were immediately apparent and the consensus was for follow-up twin diamond holes using HQ3 coring tubes. The most mineralised RC hole was selected for the first twin diamond hole. This RC hole (MS 313) encountered one intersection of >0.47 g/t; in contrast the diamond hole (MS 342) had nine intersections at > I g/t. Results at hand show definitively that face-sampling RC drilling is not acceptable as a method of exploration for gold deposits of the Woods Point type. Furthermore it is demonstrated that RC drilling should not be used for any type of exploration of high-grade gold vein deposits related to highly fractured or porous hostrock, or areas of previous mining activity. Methods are proposed for reviewing of rates of sample recovery, distribution and cross-contamination. Comparisons also show that in limited metreage reconnaissance drill programs, diamond drilling is more similar to percussion in per metre costs, than it is credited with, and always provides more bang for the Buck.

Jan 1, 1997

By P Christen, D R. Ashley, G R. Power

The Ernest Henry Mine is currently a copper-gold open pit operation situated in north-west Queensland, Australia. It is owned and operated by Xstrata Copper with a current throughput of 11 million tonnes per annum; however, open pit operations are scheduled to cease in late 2011. The deposit dips at approximately 45¦ and extends for at least another 400 vertical metres below the final 530 m deep pit design. Resource drilling from 2002 until mid 2008 has enabled an Indicated Mineral Resource to be established to 1000 m below surface. Scoping and prefeasibility studies (PFS) have been completed toward determining if this resource is suitable for underground mining and a feasibility study is currently progressing with a sublevel caving (SLC) concept. This paper briefly describes the process by which the SLC method was selected, conclusions regarding the non-selected methods, and then discusses the optimisation process used to derive the mining plan. The key optimisation parameters include the production drive spacing, level spacing, draw strategy, cut-off grade and production rate. Key risks will then be assessed and economic sensitivities studied. Final sensitivities will use Monte Carlo simulations to improve the transparency of the projectÆs risk profile. The feasibility study (FS) began in March 2008 and this paper describes the main optimisation steps at the time of writing and outlines the plan for study completion through to March 2009.

Jan 1, 2009

By P Knights

This paper examines the process and specialised skills required to extract insight from data routinely collected by mine operations, maintenance, engineering and environmental departments. Typical insights include: enhanced understanding of root causes; recommendations for next best actions; and simulation of likely scenarios. The skills required for advanced analytics are not currently the domain of mining engineers. The professions required by tomorrow’s mines are likely to be diverse and multi-disciplinary, and will include control engineers, software engineers, mathematicians and statisticians. A case study is presented that correlates mobile equipment production delays with rainfall events across three mines on the east coast of Australia. One mine is shown to have significantly more rain related downtime than the other mines, providing compelling evidence to improve productive performance.

Nov 22, 2011

By S Mundell, A Atkins, S van de Water

Geoscientific information management enables the capture, management and delivery of the original geoscientific observations and measurements of the earth’s natural resources. However, original observations and measurements are worth nothing if the quality and integrity of the data can’t be guaranteed. Geoscientific information is one of the fundamental assets enabling miners to make confident and accurate business decisions, whether that is defining a resource model, performing reconciliation, delivering ore reserve reports or meeting environmental compliance requirements. Without access to reliable, validated or verified data it increases the risk of miners using incorrect information for reporting and compliance. Industry codes, such as JORC, or government regulations, such as environmental compliance requirements, must be adhered to and companies should be able to confidently report to these standards. Without having a robust information management framework in place, it becomes a challenge to make trustworthy decisions, report confidently and reduce the risk of non-compliance. As a key initiative, good data governance should form one part of a miner’s information management strategy. Within the mining industry it is common for companies to only consider technology tools as the key focus for compliance whereas a mature information management focus will additionally consider people and process. All three pillars are critical for a miner to have confidence in their data driven decisions. This paper discusses an industry framework for best-practice geoscientific information management based on the observations gathered from analysing data management practices within the mining industry. It focuses on how the three pillars of people, process and technology are crucial elements to improve operational decisions and ensure companies are compliant.

Nov 8, 2021

By A Gerson, S Miller, R Smart, J Thomas

Environmental Geochemistry International (EGi) and the Ian Wark Research Institute (IWRI) collaborated in a three-year Australian Minerals Industry Research Association (AMIRA) research project (Project Number P387A) focussed on the prediction and kinetic control of acid mine drainage. As part of this project, single addition, and sequential net acid generation (NAG) testing was carried out on sulfide mineral samples. The test samples comprised a range of synthetic waste materials prepared using a quartz bulk and controlled quantities of the commonly occurring sulfide minerals; pyrite (FeS2), pyrrhotite (Fe7S8), arsenopyrite (AsFeS), chalcopyrite (CuFeS2), chalcocite (Cu2S), covellite (CuS), bornite (Cu5FeS4), galena (PbS) and sphalerite (ZnS). NAG test results clearly show that there are significant differences between the acid forming potential of sulfide minerals. The NAG test results for each mineral were compared with theoretical acidity values (NAPP*). The NAPP* calculation was based on stoichiometric oxidation reactions assumed for each of the sulfide minerals. Sequential NAG values for pyrite corresponds closely to predicted NAPP* values, confirming the assumption that pyrite oxidation occurs according to the stoichiometry assumed. For the pyrite sample with 5 wt per cent S, two NAG stages were sufficient for all of the sulfur to be released to solution. Since sulfides in waste materials will generally be dominated by pyrite, results also confirm the validity of including NAG testing for ARD evaluation of most waste rock. NAG testing confirms that of the sulfide minerals examined, only pyrite, pyrrhotite, arsenopyrite and chalcopyrite are acid producing, ie able to produce leachate with a pH less than 4.5. In the case of sphalerite, galena, bornite, chalcocite and covellite the pH of the final NAG solution was greater than 4.5. The significant differences between the acid forming potential of different sulfide minerals could lead to overestimation of acid producing potentials based on NAPP values calculated from total per cent S alone, ie assuming all S is present as pyrite. The oxidation of galena during the NAG test resulted in the consumption of acid. The examination of the galena surface by X-ray photoelectron spectroscopy (XPS) after oxidation in peroxide solution indicated the presence of polysulfide. The reaction of sulfide to polysulfide is acid consuming, thus explaining the net acid consuming behaviour of galena in the NAG test. This reaction pathway may provide a possible explanation for the lower than expected acid production observed for some of the other sulfide minerals examined.

Jan 1, 2003

The Late Permian intermediate to silicic talc-alkaline Drake Volcanics of New England, N.S.W., consist largely of shallow marine, redeposited volcaniclastic rocks which host epithermal Ag-Au deposits. Pervasive hydro- thermal alteration is widespread. The 200-300 m Cataract River Member includes several sedimen- tation cycles composed of massive pumice brec- cias, overlain by laminated sandstones and siltstones, interbedded with marine, fossil- iferous mudstones. Two distinct groups of cla- sts exist within the volcaniclastic beds: 1. Lithics of predominantly intermediate compos- ition lavas that have undergone subaerial epi- clastic erosion and transportation; 2.Pumice, quartz and plagioclase crystals which have not been reworked by epiclastic processes. The lithic clasts were derived locally in a sub- aerial environment within the Drake Volcanics, and pumice and crystal fragments from contem- poraneous centres of silicic volcanism else- where in New England, N.S.W. The latter group of clasts was transported to Drake by Plinian airfall or rafting, and fell and was washed on- to emergent portions of the Drake Volcanics, where reworked locally derived fragments occ- urred. Cold state subaqueous mass-flows, prod- uced by slumping, resedimented the mixed vol- caniclastic detritus into the marine basin in a series of cyclic units with massive lower parts, and laminated upper zones. Modern ana- logs of the palaeogeographic setting in New England, N.S.W., in the Late Permian are pro- vided by the Taupo Zone, New Zealand, and sou- thern Kyushu, Japan.

Jan 1, 1987

By Dobos SK

The Black Ridge Gold Deposit is located in the northern part of the Clermont Goldfield, which is situated at the boundary of the Bowen Basin and Anakie Inlier, Queensland. The goldfield comprises a series of NNW-trending semi-isolated basins, which are tectonically aligned with the Denison Trough, the west-most division of the Bowen Basin (Fig. 1-1).The main stratigraphic units in the deposits in younging sequence are the Anakie Metamorphics, the early Permian Blair Athol Coal Measures, the late Permian(?) White Section, and the Tertiary basalts which are regionally widespread, and intruded by abundant mafic and felsic plugs.

Jan 1, 1990

By Denby B

The ever increasing demand on land use has led to large areas of land being considered for development, which because of past mining activities are covered by substantial depths of fill materials. This paper examines the problem faced with the development of land infilled with open cast mining backfill, in predicting the behaviour of the fill upon development. To be able to design foundations suitable to withstand the movements that occur within open cast backfills or design a backfilling operation that produces land suitable for a proposed after development, a means of predicting backfill settlement is required. Factors critical to this prediction are the timing of backfilling operations, the compactive state of the backfill and the inundation of the backfill. The analysis of a considerable quantity of data collected from the monitoring of backfilling operations and backfill movement at a range of open cast coal sites located within the UK has given the authors a better understanding of how open cast backfills behave in terms of long-term creep settlement, collapse settlement and how these are effected by backfill scheduling. This knowledge has been encoded into a program running under Microsoft Windows that enables a user to make settlement predictions for a point, a given section or area or for the whole site. Differential settlements, critical to any development design, can also be determined between any two points taking into consideration the heterogeneous nature of open cast backfills. The program was tested with data from an open cast coal site in the UK. Compaction monitoring during the placement of the backfill material enabled a model of the backfill to be constructed taking into account backfill properties and scheduling. This model, taken as input into the program, enabled future backfill settlement predictions to be made. A comparison is given between these results and actual settlements obtained from a short-term settlement monitoring scheme.

Jan 1, 1995

By Guerney P. J

A suspension of finely powdered ferrosilicon in water is the dense medium used in the gravity upgrading of iron ore, diamonds and other minerals. Ferrosilicon can he lost in the plant through corrosion. The greatest corrosion losses occur when

Jan 1, 1997

Coal geology plays an essential role in the investigation of in situ coal seam quality. Coal geology can also play an important part in laboratory studies such as coal washing and coking, and in operating plant problems.

Jan 1, 1976

By Jackson GS

Since 1983 Cobar Mines Pty Ltd has madea concerted effort to improve the performance of its long hole open stopes, especially in the areas of dilution and fragmentation.This has resulted in modifications to stope design, drilling and blasting practice.

Jan 1, 1985

By C Vejrazka, A Wyllie

A common problem faced by underground mining operations around the world is airborne dust sourced from production and auxiliary processes. In most underground mining methods, air is generally directed through a limited number of drives and is thus more effective at carrying dust away from operational areas quickly. In a block caving operation, there are a number of ways to set up ventilation systems. In its simplest form the air is entering the extraction level through access drives and then split over the number of extraction drives—based on the pressure differences—without being regulated. This is the case at Northparkes Mines. Larger operations and panel caves most often utilise designated ventilation levels and ventilation raises with some form of regulation to ensure adequate airflow to all work areas.Northparkes Mines utilise electric loaders as a productive means to transport ore to the run-of-mine (ROM) bin, which have the added advantage of allowing the mine to require less airflow through the extraction drives as dilution of exhaust gases is no longer required. Dust was controlled during the operational period of the previous two block caves by using water spray bars in each of the drawpoints, which were seen as the main source of dust. These drawpoint spray bars only wet the surface of muck piles and require a lot of water to achieve an effect on the overall air quality. The drawpoint sprays can be remotely operated from mine control, whenever a loader is sent to bog a particular drawpoint. A significant amount of airborne dust is also generated during loading as rilling of material occurs, with further dust being generated during tramming and dumping activities as only limited mixing of the water and ore occurs. The water sprays are ineffective at precipitating dust that has already become airborne.When built, the currently operational E48 cave was fitted with drawpoint water sprays. As the cave is in a different orebody with higher silica content, the water sprays were not able to keep airborne dust and thus silica quantities under control efficiently. It was therefore necessary to find more sustainable solutions. The problem was further intensified by the concurrent load-haul-dump (LHD) processes across multiple extraction drives and tipping points, as well as secondary breaking, using non-explosive blasting and development activities occurring nearby.This paper describes the practical approach taken at Northparkes Mines to reduce personal dust exposure on the E48 extraction level. As the extraction level is one of the main contributors to airborne dust at the mine, it is believed that much can be learnt by focusing improvement efforts initially on this part of the mining process and later applying the effective solutions in other parts of the mine.CITATION:Vejrazka, C and Wyllie, A, 2014. Reduction of airborne dust on the E48 extraction level at Northparkes mines, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 227–232 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By T Peglas, A de Aboitiz

The Queensland Government, via the special purpose company vehicle û City North Infrastructure Pty Ltd û is currently developing BrisbaneÆs Airport Link underground toll road and Northern Busway (Windsor to Kedron).Airport Link is a predominantly underground toll road planned between BrisbaneÆs northern suburbs, the airport and the Brisbane Central Business District (CBD) frame. The Northern Busway forms part of BrisbaneÆs expanding busway network, sections of which will be jointly delivered with Airport Link. Airport Link will connect the North-South Bypass Tunnel, Inner City Bypass and local road network at Bowen Hills to the northern arterials of Gympie Road and Stafford Road at Kedron and Sandgate Road and the East-West Arterial in the cityÆs north-east. The Northern Busway is a two-lane, two-way bus-only roadway proposed to connect the existing Inner Northern Busway at Herston with Windsor, Lutwyche, Kedron, Chermside, Aspley and Bracken Ridge. Airport Link and Northern Busway (Windsor to Kedron) is one of the largest infrastructure projects planned in the first phase of the State GovernmentÆs South East Queensland Infrastructure Plan and Program. The paper will provide an overview of the projects, including a discussion on the technical and environmental aspects as well as the procurement of the Airport Link as a public private partnership.

Jan 1, 2008

By Whitham M

Prior to exploitation, the feasibility of mining and recovering ore can usually be determined to a satisfactory level of uncertainty by the consideration of conceptual scenarios, using a range of reasonable parameter values. Such values are selected on experience, knowledge of other mining operations, and the characteristics of the particular deposit being considered. Having established such feasibility, it is usually considerably more demanding to determine what the optimum set of parameters might be. Yet many decisions taken at the feasibility stage represent commitments extending at least into the medium term.

Jan 1, 1991

Developed and built in 1982 for simultaneous bathy-metric and reflectivity mapping of the deep ocean by the Hawaii Institute of Geophysics, SeaMARC II was a breakthrough in sea-floor mapping technology. The design was developed cooperatively by industry and academia, and the system has served as a prototype for a new generation of mapping tools for operation in both shallow and deep water.Research programs using the SeaMARC II system have focussed on basic research into the geophysical evo-lution of the Pacific, ranging from intra-atoll mapping to surveys of the deep-sea trenches. During the past few years most work has been concentrated on detailed investigations of the morphology of mid-ocean spread-ing centers, seamounts, and the subduction zones which surround the Pacific. The detail provided by the high resolution, 10-km wide side-scan sonar images of fault and fold structures, combined with the swath of bathy-metric information obtained simultaneously, allow previ-ously unattainable analysis of seafloor morphology and are leading to development of detailed models for ocean crust genesis and deformation.

Jan 1, 1990

By T Connor

Alkali emissions are one of the environmental challenges facing alumina refineries. Queensland Alumina Limited (QAL) is undertaking a number of initiatives to continuously improve its environmental performance. One of these is a program aimed at the reduction of alkali emissions. Alkali emissions originate from a number of sources (eg elevated open tanks), and its level depends on a number of process parameters/ mechanisms (ie splash filling, thermal currents in tanks, streams discharged from a pipe, tank temperatures, atomisation) and climatic conditions (eg wind speed and direction, rain, etc). Under normal operating conditions, there is a continuous low level of alkali emissions from the plant. Certain vessels within the plant have been identified as major contributors to this level of emission, while certain activities within the plant contribute to a temporary elevation (æspikeÆ) of alkali emissions. QAL developed a method using phenolphthalein-treated pads to measure emissions within and outside QAL boundaries. These provide no information about mass emission rates but are important for detecting if alkali material is present. Since mass emission rates are important for determining if improvements in emissions are made, QAL identified the need to design an improved sampling method. Following the development and implementation of a sampling and analysis method to monitor alkali emission concentrations, QAL is conducting a number of feasibility studies evaluating a range of alkali emission reduction options. The alkali measurement method will be used to track and demonstrate progress in this environmental initiative. This paper will discuss the measurement method and emission reduction options being evaluated.

Jan 1, 2005

Laboratory experiments have been used tostudy a wide range of convective processes which are significant for the formation of rocks and the ores that form in them. Metal-rich solutions flowing through the sea floor produce 'black smoker' chimneys; both the size and structure of a solid chimney and the height to which the plume of effluent rises above it can be predicted using model experiments. Analogues of processes in solidifying magmas can also be studied using crystallizing aqueous solutions. The release of lighter or denser residual fluid as crystallization proceeds, and the resulting compositional convection, have a vital influence on the differentiation of initially homogeneous magma and on the evolution of stratified magma chambers. Mixing during the replenishment of magma chambers, and its dependence on the rate of filling and on the fluid properties, have also been studied on the laboratory scale. Experiments carried out in different geometries have been applied here to the formation of platinum and chromite ores and komatiite lavas. Larger-scale mantle convection, in particular the motion of subducting plates and plumes rising from the core-mantle boundary, also determine the tectonic settings in which ore bodies form. These phenomena too can be usefully investigated in laboratory experiments using very viscous fluids.

Jan 1, 1990