Search Documents

By George A. Packard

THE experiments here described were made under my supervision while temporarily acting as head of the Department of Metallurgy at the Missouri School of Mines, at Rolla. The work was done by Messrs. W. E. Brown, W. C. Richards, and F. L. L. Wilson, and the description of the results forms a portion of a thesis presented for the degree of Bachelor of Science. These results are submitted because I have seen no description of the application of pot roasting to the treatment of a copper-concentrate. This work followed that already described in the discussion of the ' Lime-Roasting of a Galena-Concentrate,"' and was similarly occasioned by the lack of a furnace of the reverberatory type in which the copper-concentrates could be smelted. The material for the tests was a mixture of three lots available. The first consisted of 8-mm. jig-concentrates and the second of 0.5 mm. table-concentrates, from the San Juan district, Colo. Both contained pyrite, chalcopyrite and galena. The third was a lot of copper-ore, found in the laboratory, which had been crushed through 8-mm. screen, and had at some previous time, before the laboratory roasting-furnace was torn down, received a partial roasting. The analyses of these ores are given in Table I. In order to determine the applicability of pot-roasting as to each lot of ore, and the effect of varying proportions of lime, six preliminary tests were made in a " size N " Battersea crucible, 9 in. high by 6 in. in diameter at top, with a 5/8 in. hole bored through the bottom. The crucible was set in the upturned elbow of a 2-in. pipe, the joint being luted with clay; and air was obtained from a receiver supplied by a compressor. The

Jan 1, 1908

By Gordon S. Duncan

(New York Meeting, February, 1912 THE U. S. Geological Survey, I believe, has almost completed a study of the Harney Peak quadrangle, preliminary to the publication of a report on that, district. As I was engaged for some months on an investigation of the mode of occurrence of the ore-bearing formation in this area, it has seemed to me timely to make public the results of my study, as a contribution to the consideration of this subject. It seems scarcely necessary to describe the locality and general geology of the Black hills of South Dakota, for since 1846 many have contributed information concerning this region, some of the reports bearing such well-known names as those of Walter P. Jenney, Henry Newton, S. F. Emmons, and C. R. Van Hise, while we have only to glance at Bulletin No. 4 of the South Dakota School of Mines, in which Prof. C. C. O'Harra, of that institution, has given us a bibliography of contributions to the geography and geology of the section, to find that other well-known men have studied the district, and have given us the benefit of their researches. The U. S. Geological Survey has made geological maps of nearly the whole of the Black hills, the only quadrangle yet to be completed being, as stated, the Harney Peak district. During the late summer and autnmn of 1910, it was my lot to examine and report. on a considerable area in this neighborhood, which once had been prospected, and in some cases exploited, for tin. This paper gives an account of certain geological phenomena, noted at that time, which greatly influenced my conclnsions. The predominating formation of the district is pre-Cambrian, represented by a highly-cleaved mica-schist, usually very garnetiferous, and sometimes hornblendic. Rising like an island from the surrounding schist is a large mass of granite, known as

Jul 1, 1912

By Robert W. Hunt

The memorable features of American history have been making fast during the last century, and notably so since 1860; and they are by no means confined to political or to any one branch of scientific development. Of all the industrial arts, none show a greater change or 'a mightier progress than the Bessemer manufacture. And this year, while we are celebrating the first centennial of our national life, we can also celebrate the first decennial of American Bessemer practice. While not forgetting or undervaluing what has been done in other countries, I have thought that a brief history of the introduction and development of the Pneumatic or Bessemer process in America would be of interest. In 1863 the Kelly Pneumatic Process Company was formed and an arrangement entered into with William Kelly, who had taken out letters-patent of the United States, Nos. 16,444; 17,628, reissued as 505; 18,910, dated January loth, 1857; June 23d, 1857; November 36, 1857; and December 22d, 1867, respectively. This association mas composed of the Cambria Iron Company, E. B. Ward, Park Brothers & Co., Lyon, Shorb & Co., Z. S. Durfee, and, later, Chouteau, Harrison & Valle joined the combination. Not satisfied with possessing the control of the Kelly patent, they sent Mr. 2. S. Durfee to England, to secure for this country Mushet's patent on recarburization, No. 17,389, dated May 26th, 1857, the same having been taken out in England on September 22d, 1856. In this Mr. Durfee was successful. Previous to the application of William Kelly for a patent, Henry Bessemer, of England, had taken out patents dated February 12th, 1856, and August 25th, 1856, in this country. Kelly claimed priority in the discovery of the principles of the process, and the Patent-office allowed his claim by granting him his patents. In the autumn of 1862 Mr. Alexander L. Holley, while in England, was impressed with the importance of Mr. Bessemer's invention, and so fully foresaw its future, that, upon his return to the United States, he induced Messrs. John A. Griswold and John F. Winslow, of Troy, New York, to join him in endeavoring to possess Bessemer's American patents. Mr. Holley returned to England in

By Maurice L. Pinel, Thomas T. Read, Thomas A. Wright

THE erroneous, but until recently widely prevalent, belief that iron castings were first made in Europe in the fourteenth century has been adequately refuted in a number of earlier papers;1,11,12 but except for an unpublished metallographic study by the late William Campbell, and a phosphorus analysis by T. A. Wright of the metal of the Han dynasty cast-iron stove described by Laufer,2 nothing was known of either the chemical composition or the metallographic structure of the metal of any ancient iron casting, although data on castings of recent manufacture are abundantly available. The metal of the stove, which had been buried in a grave for at least 15 centuries, was so corroded that it seemed inadvisable to publish the results on it until more and better specimens from other ancient castings could be obtained. During a journey through China, extending from Peking in the north to Canton in the south and Cheng-tu, Ssu-chuan, in the west, in the late summer and autumn of 1936, one of us (T. T. Read) was fortunate enough to obtain, and bring home for study, nine castings, all more than 1000 years old, of which the date of manufacture is precisely known because of inscriptions cast in them, another that lacks a dated inscription, but of which the date, as explained below, can be otherwise established, and a specimen from the largest iron casting ever made," which is also dated. The period covered by this suite of specimens extends from 502 to 1093 A.D. In addition, a sample was obtained from a casting of date unknown, but which was certainly cast before 1000 A.D. and possibly as early as the third century A.D. A detailed description of these specimens is as follows: 1. 502 A.D. A pair (right and left) of recumbent lions (Fig. 1). Base 7 ¼ by 14 3/8 in., height over-all 5 ½ in., weight 26 lb. each. The translation of the inscription on the base is: "Made on the twenty-fourth day of the seventh month of the third year of Ching Ming of Great Wei" (Sept. 11, 502 A.D.).

Jan 1, 1938

By Walter McKee

WHEN mixed with common cast steel in quantities ranging from 11 to 13 ½ per cent. and properly treated, manganese increases the ductility of the metal and adds greatly to its toughness and resistance to abrasive action, which properties comprise the distinctive characteristics that make manganese steel so valuable for many purposes at the present time. Manganese steel has been manufactured for about 26 years. .It was first made in a small way in England and subsequently produced in the United States in 1892. At present the manganese-steel foundries of this country have an annual capacity of about 60,000 tons and most of the growth has occurred within the past 10 years. In the early days of the industry it was impracticable to make manganese castings weighing over a few thousand pounds, but at present crusher heads, rolling-mill pinions, and similar castings weighing up to 30,000 lb. each are produced, and it does not appear that the limit of weight has been reached by a considerable margin. Manganese steel is similar in analysis to ordinary first-class converter metal except that it is high in carbon and contains from 11 to 13 ½ per cent. of manganese. From one standpoint manganese steel is similar to malleable iron in that the casting as it comes out of the sand is hard and brittle and must be made ductile by a heat-treating process. The heat treatment is an essential part of the process of making manganese-steel castings and must be properly carried out to secure satisfactory results. The necessity for heat treatment limits the thickness of sections which may be made of manganese steel. Originally the annealing depth was comparatively small, but researches carried on during the past few years have resulted in an increase in the thickness of section up to 5 ½ in., which it is possible to treat successfully. Large castings are cored out to a minimum thickness of 5 ½ in., thus not only eliminating some of the internal stresses which are invariably set up in a very thick casting, but also reducing the weight and inertia of the piece, an

Jan 12, 1915

By C. S. Anderson

Georgia, since 1829, has produced nearly $18,000,000 from her gold mines, but in late years the output has dwindled to insignificance. In view of present universal efforts to increase gold production, it seems pertinent to record some recent observations in that field, briefly review its past and weigh probabilities of reviving gold mining there. Little in this paper can be claimed as new or original, and it does not present results of a detailed or profound investigation of the whole region. The Allatoona gold mine was reopened in January, 1932, and explored at greater depth during the period from January to June of that year. A number of other abandoned mines were visited, but since the workings, in common with most such mines in Georgia, were flooded or caved, underground conditions could not be examined. For a wider knowledge of the subject, a search was made through available pertinent literature and statistics, a bibliography of which is appended hereto. To all the sources obligations are gratefully acknowledged. Production The discovery of gold in Georgia, in 1829, led to an influx of 6000 to 7000 miners and a production of over $200,000 in the following year. A branch of the United States Mint, established at Dahlonega in 1838, accounted for $6,115,569 up to the time of the Civil War. The output fluctuated greatly from year to year, with an all-time peak of $582,782 in 1843. In only one other year, 1845, was the half million mark exceeded. After the war mining began again, but 1883 is the last year for which an output of $200,000 is reported. Placers, always the main source of production, were yielding less and less, and in spite of increased quartz-mining activities the downward trend continued. The last year in which there was a production of $100,000 was 1902. In 1914, $16,270 came from 26 placers and 11 deep mines, with the latter reporting 1750 tons of $3 average value. In 1925, one placer and four lode mines that mined 8100 tons assaying $1.19 per ton produced $9500. One placer and one quartz mine, operating in 1930, reported a total output of $4194. Table 1 pictures the waning output.

Jan 1, 1934

By David B. Reger

Exploration for new pools of gas in the Oriskany sand and continued exploitation of areas already known to be productive in that sand were the main features of petroleum activity in West Virginia during 1938. To a considerable extent the exploration program resulted in failure, but the extension of former areas was eminently successful. Throughout the state, in general, less drilling was done than in 1937. According to the West Virginia Department of Mines, only 631 permits to drill were issued, as compared to 1034 in 1937. The account of operations, as reported by trade journals and other sources, shows that 766 wells were drilled, resulting in 131 oil wells with 1609 bbl. of daily production; 484 gas wells with 1,232,216,000 cu. ft. of daily open flow; and 151 dry holes. Several discoveries indicate new pools of oil and gas; and several extensions of old gas pools have been made. In spite of a decreased number of total wells, the figures for new gas and oil are both larger than in 1937. The new oil average is 12.3 bbl. per well per day; the gas average is 2,545,900 cu. ft. per well per day, the ratio of dry holes to completions is 19.71 per cent. No general attempt was made to discover new pools of oil. A continued low price, coupled with reduced takings, combined to make drilling unattractive. The principal oil wells completed, by counties are: Boone, 6; Calhoun, 10; Clay, 7; Gilmer, 5; Kanawha, 5; Lincoln, 7; Pleasants, 13; Ritchie, 32; Roane, 6; Tyler, 7; and Wirt, 14. Production for the year, according to the Oil and Gas Journal, was 3,724,750 barrels. The leading counties in gas, with the number of successful wells in each, are: Boone, 16; Braxton, 13; Cabell, 47; Calhoun, 29; Doddridge, 10; Gilmer, 55; Kanawha, 127; Lincoln, 18; Ritchie, 29; Wayne, 19; and Wetzel, 26. Production for the year is estimated as 150,000,000,000 cubic feet. Pipe-line construction, which was extensive in 1937, was insignificant in 1938. Exploration was not as active as in 1937. Field prices of both oil and gas have severely declined.

Jan 1, 1939

By David B. Reger

Exploration for new pools of gas in the Oriskany sand and continued exploitation of areas already known to be productive in that sand were the main features of petroleum activity in West Virginia during 1938. To a considerable extent the exploration program resulted in failure, but the extension of former areas was eminently successful. Throughout the state, in general, less drilling was done than in 1937. According to the West Virginia Department of Mines, only 631 permits to drill were issued, as compared to 1034 in 1937. The account of operations, as reported by trade journals and other sources, shows that 766 wells were drilled, resulting in 131 oil wells with 1609 bbl. of daily production; 484 gas wells with 1,232,216,000 cu. ft. of daily open flow; and 151 dry holes. Several discoveries indicate new pools of oil and gas; and several extensions of old gas pools have been made. In spite of a decreased number of total wells, the figures for new gas and oil are both larger than in 1937. The new oil average is 12.3 bbl. per well per day; the gas average is 2,545,900 cu. ft. per well per day, the ratio of dry holes to completions is 19.71 per cent. No general attempt was made to discover new pools of oil. A continued low price, coupled with reduced takings, combined to make drilling unattractive. The principal oil wells completed, by counties are: Boone, 6; Calhoun, 10; Clay, 7; Gilmer, 5; Kanawha, 5; Lincoln, 7; Pleasants, 13; Ritchie, 32; Roane, 6; Tyler, 7; and Wirt, 14. Production for the year, according to the Oil and Gas Journal, was 3,724,750 barrels. The leading counties in gas, with the number of successful wells in each, are: Boone, 16; Braxton, 13; Cabell, 47; Calhoun, 29; Doddridge, 10; Gilmer, 55; Kanawha, 127; Lincoln, 18; Ritchie, 29; Wayne, 19; and Wetzel, 26. Production for the year is estimated as 150,000,000,000 cubic feet. Pipe-line construction, which was extensive in 1937, was insignificant in 1938. Exploration was not as active as in 1937. Field prices of both oil and gas have severely declined.

Jan 1, 1939

By Robert E. Sorenson

EXPLORATION for deep-seated orebodies in the Silver Belt area of the Coeur d'Alene mining district is complicated by meager surface expressions of diagnostic criteria, lack of knowledge of the significance of specific alteration phenomena, and the great expense involved in the exploration for ore shoots, the tops of which often occur near sea level elevation or below and as much as 4000 ft or more below the surface. Except for the early studies of Ransome and Calkins in 1903 and 1904,' little geological work was done in the Coeur d'Alene district for many years, and it is only during the last 15 to 20 years that complete and careful geological mapping has been applied to most of the mines in the area. Much early information, which now would prove invaluable, is lost in hundreds of miles of caved and inaccessible mine openings not mapped by mining geologists. In more recent years mining geology has become a tool of greater use in the district, and some measurable progress is being made in the accumulation of observations that are adding gradually to the knowledge of ore deposits in the district. The recognition of alteration phenomena and related features by Hoyt S. Gale3 in 1935, followed by the work of Shenon and McConnel in 1936-37,4 changed many of the concepts formerly held and opened the way for more critical study and mapping of alteration effects. Mapping of these effects has been in progress for several years but no well-organized, careful, and complete laboratory study of the alteration has been made by mining companies or by government agencies. Recently, Thomas Mitcham of Columbia University has been occupied in the collection and study of specimens carefully selected from several producing mines in the Silver Belt as well as from several prospects exhibiting alteration effects. Mr. Mitcham and the writer have discussed some of the preliminary results of his investigations, which indicate that definite and interesting material is forthcoming from his studies. Work of this kind, aided by careful observation by district geologists, should advance the knowledge of the environment of Silver Belt ore shoots and establish additional criteria for recognizing meager shallow expressions of deep-lying orebodies. Structural details in the Silver Belt area are extremely difficult to decipher on the surface because the area is almost completely covered by a deep mantle of surface debris and soil. A dense growth of small trees and buck brush adds to a geologist's difficulties. Often large areas reveal only scattered small outcrops with great intervening areas where the underlying formations must be deduced from small altered rock fragments. Some considerable success in obtaining surface information has come from bulldozer roads and cuts in selected areas. As this type of work receives more attention, knowledge of the surface expressions of formations, alterations, faulting, and veining is expanding and giving more reliable information to guide deeper development. Lack of diagnostic marker beds in the district contributes to a geologist's difficulties in determining fault displacements. In the Silver Belt, known commercally important sulphide orebodies commonly are associated with siderite and quartz gangue. Some of the veins at shallow horizons above productive ore shoots are composed of quartz with light-colored carbonate minerals such as calcite, ferrocalcite, ferrodolomite, ankerite, and carbonates with variable amounts of manganese. The relation of these carbonates to commercial orebodies is a problem offering possibilities for research. Shallow exposures of veins composed of quartz and the light-colored carbonates, often with some associated barite, grade into quartz and siderite veins at deeper horizons. The vertical range of these carbonates has been partially established for some veins, but no reliable method has been devised for predicting where the change in a vein may take place. Careful observation and analysis of carbonates may make it possible to predict more closely where the change to siderite may be expected. In 1926 Shannon5 pointed out some of the characteristics of the carbonate veins of the district and included a few chemical analyses. Some of the Silver Belt ore shoots have small commercial outcrops, and very shallow development of some properties has led to the opening of small ore shoots." Several small ore shoots developed at shallow depths have not been explored at deep horizons, and some important ore shoots with no commercially significant exposures at shallow horizons have been developed. The greatest problem of the mining geologist working in the Silver Belt area is to find the all-important link between the very meager shallow expressions of mineralization and the rich ore shoots that may be found below. To develop criteria for use in the recognition of the weak upper expression of ore shoots, the experience of past development programs must be relied upon heavily. The investment of more than a million dollars in the exploration for such ore shoots requires some reliable criteria if these ore shoots are to be found. Management needs some assurance that the risk involved is justified by well-developed and acceptable geological inference. The richness of some of the ore shoots found thus far has contributed greatly to the justification for a bold approach, but many negative results of blind exploration programs would lead eventually to extreme caution on the part of management. Fortunately, recent experiences of development programs have been quite successful. It is hoped that added knowledge. of the environment of Silver Belt ore shoots will contribute greatly to the sureness of approach toward their development. The Coeur d'Alene mining district is located in the panhandle of Idaho in Shoshone County. The population of the county is either employed in the

Jan 1, 1952

By Frederic Benard

Recovery of selenium and tellurium at Copper Cliff by the Ontario Refining Co. has been previously described by the writer.l During 1935 a new building was erected to house this operation and description of the new plant and process form the subject of this paper. The building, of modern steel and tile construction, covers an area of 5900 sq. ft. with a volume of approximately 166,000 cu. ft. The large monitored center bay is flanked by two smaller outside bays, one of which is devoted to the tellurium section. All equipment, ceilings and upper walls, are treated with aluminum paint, giving good illumination and facilitating good housekeeping, essential from a health standpoint in handling material of this nature. Equipment Layout and type of equipment conforms to the requirements of the process as described below. In the selenium section, storage tanks, neutralizing tanks and precipitators are of steel construction, lead-lined and arranged for gravity flow (Fig. 1). The neutralizing tanks are equipped with water-cooled lead coils for controlling solution temperature, agitation being accomplished with compressed air. The precipitators are provided with mechanical agitators, and sulphur dioxide is introduced into the solution through 1/2-in. lead pipes leading from a manifold attached to the cover of the precipitator. Each precipitator has internal cooling coils and an air-jet exhauster to carry off fumes. Neutralized solutions are filtered in a 29-plate wooden filter press using heavy cotton duck as a filter medium, forced feed being maintained by a Welmet centrifugal pump. Dilute solutions are concentrated by evaporation in a vacuum evaporator, constructed of cast hard lead. Heat is supplied by an outside steam chest operating under 15 Ib. steam pressure. The solution is circulated through the steam chest by a pump of antimonial lead at a rate approximating 400 cu. ft. per min. The evaporator is evacuated by a water-jet condenser that creates a vacuum of 26 in. of mercury under normal operating conditions. The capacity of the vessel is 60 cu. ft. and the rate of evaporation 25 cu. ft. per hour.

Jan 1, 1943

By Frederic Benard

Recovery of selenium and tellurium at Copper Cliff by the Ontario Refining Co. has been previously described by the writer.l During 1935 a new building was erected to house this operation and description of the new plant and process form the subject of this paper. The building, of modern steel and tile construction, covers an area of 5900 sq. ft. with a volume of approximately 166,000 cu. ft. The large monitored center bay is flanked by two smaller outside bays, one of which is devoted to the tellurium section. All equipment, ceilings and upper walls, are treated with aluminum paint, giving good illumination and facilitating good housekeeping, essential from a health standpoint in handling material of this nature. Equipment Layout and type of equipment conforms to the requirements of the process as described below. In the selenium section, storage tanks, neutralizing tanks and precipitators are of steel construction, lead-lined and arranged for gravity flow (Fig. 1). The neutralizing tanks are equipped with water-cooled lead coils for controlling solution temperature, agitation being accomplished with compressed air. The precipitators are provided with mechanical agitators, and sulphur dioxide is introduced into the solution through 1/2-in. lead pipes leading from a manifold attached to the cover of the precipitator. Each precipitator has internal cooling coils and an air-jet exhauster to carry off fumes. Neutralized solutions are filtered in a 29-plate wooden filter press using heavy cotton duck as a filter medium, forced feed being maintained by a Welmet centrifugal pump. Dilute solutions are concentrated by evaporation in a vacuum evaporator, constructed of cast hard lead. Heat is supplied by an outside steam chest operating under 15 Ib. steam pressure. The solution is circulated through the steam chest by a pump of antimonial lead at a rate approximating 400 cu. ft. per min. The evaporator is evacuated by a water-jet condenser that creates a vacuum of 26 in. of mercury under normal operating conditions. The capacity of the vessel is 60 cu. ft. and the rate of evaporation 25 cu. ft. per hour.

Jan 1, 1943

By Virgil R. D. Kirkham

RECONNAISSANCE of a part of southeastern Idaho and small strip of western Wyoming lying between longitudes 111° and 111° and 45' W., and latitudes 43° and 43° and 30' N., comprising an area of approximately 1330 sq. mi., was undertaken during the summer of 1923 for the collection of data regarding the oil possibilities of the region. TOPOGRAPHY, SETTLEMENT, AND ACCESSIBILITY The entire area lies within the upper Snake River drainage basin. Snake River flows through the northeastern and eastern part of the area in a northwesterly direction. The entire drainage system has been controlled by the structure of the sedimentary beds in the area, which exhibit numerous alternations of hard and soft strata with consequent unequal erosion. The headwaters of the most important streams, as well as many others, flow in a northwesterly or southeasterly direction along

Jan 1, 1925

By R. H. Oliver

The purposes, types, preparation, and testing of flocculants are discussed. A flocculation compendium is included, indicating choice of flocculant for a given set of conditions. An economic evaluation of the process is presented. Solid-liquid separation is a major expense in most mineral processing flowsheets today. Proper use of flocculation can often lower the overall cost of a solid-liquid separation by reducing the size of sedimentation or filtration equipment. PURPOSE OF FLOCCULATION When is use of a flocculant justified in terms of overall process economy? 1) when it results in process improvement, such as producing a clear liquor for electrolysis, precipitation, ion exchange, or solvent extraction; 2) when it results in satisfying requirements of pollution abatement ordinances; 3) when it results in increased recovery of values that would otherwise be lost; or 4) when it results in considerable savings in capital expenditure due to use of smaller equipment. When can the use of a flocculant adversely effect overall process economy? 1) when it results in increased filter cake moisture, 2) when it results in decreased filtration rates, 3) when it results in considerable bulking of sedimentation underflow, 4) when it contaminates either the supernatant or sludge, or 5) when the cost of using the flocculant is greater than the savings due to its use. First step in consideration of flocculants for a given application is establishment of desired goals in terms of increased clarity of effluent, increased recovery of solids, or decreased size of equipment. The most economical solution to a solid-liquid separation problem is that combination of equipment and flocculant costs which meets the established goals at the lowest total annual expenditure. This economic decision can be made only after technical data has been obtained as outlined in next four sections. TYPES OF FLOCCULATION Flocculation is a process wherein individual particles are united into more or less tightly bound agglomerates or flocs, thereby increasing effective particle size of solids suspended in a liquid. Degree of flocculation of a suspension of finely divided solids in a liquid is controlled by a combination of probability of collision between particles and probability of adhesion after the collision has occurred.' Probability of collision can be increased commercially through use of a paddle-type flocculator, combination flocculator, and clarifier or flocculating-type feedwell. Probability of adhesion usually can be increased by addition of a reagent known as a flocculant. Reagents act as flocculants through one or a combination of three possible mechanisms. The first is electrolytic neutralization of inter molecular repulsive force due to Zeta potential. This neutralization enables Van der Waal's cohesive force to hold the particles together after they collide.' The second is the precipitation, within a definite pH range, of voluminous metallic hydroxide flocs which entrap fine particles. This process is known as coagulation.14 Third is the bridging of two or more particles by either natural or synthetic long-chain, high-molecular-weight organic polymers. This bridging is accomplished by adsorption of two particles at different sites on the same molecule or by bonding of two molecules, each adsorbed to a different particle. Considerable effort has been expended in explaining the action of these polyelec-trolytes and detailed accounts are available in the literature. CHOICE OF FLOCCULANTS It is impossible, at the present time, to specify the optimum type or amount of flocculant for a given application from a knowledge of the material to be treated. The standard procedure is to choose reagents or combination of reagents most likely to be effective on the slurry; then test them.' The accompanying Flocculation Compendium (Table I) contains details of all currently available reagents sold as flocculants and it should be used when selecting the group of reagents for tests. This selection can be based on information listed in columns 4 and 5. Column 4 presents industries in which each floc-

Jan 1, 1961

By Frederic Benard

RECOVERY of selenium and tellurium at Copper Cliff by the Ontario Refining Co. has been previously described by the writer.1 During 1935 a new building was erected to house this operation and description of the new plant and process form the subject of this paper. The building, of modern steel and tile construction, covers an area of 5900 sq. ft. with a volume of approximately 165,000 cu. ft. The large monitored center bay is flanked by two smaller outside bays, one of which is devoted to the tellurium section. All equipment, ceilings and upper walls, are treated with aluminum paint, giving good illumination and facilitating good housekeeping, essential from a health standpoint in handling material of this nature. EQUIPMENT Layout and type of equipment conforms to the requirements of the process as described below. In the selenium section, storage tanks, neutralizing tanks and precipitators are of steel construction, lead-lined and. arranged for gravity flow (Fig. 1). The neutralizing tanks are equipped with water-cooled lead coils for controlling solution temperature, agitation being accomplished with compressed air. The precipitators are provided with mechanical agitators, and sulphur dioxide is introduced into the solution through 3-in. lead pipes leading from a manifold attached to the cover of the precipitator. Each precipitator has internal cooling coils and an air-jet exhauster to carry off fumes. Neutralized solutions are filtered in a 29-plate wooden filter press using heavy cotton duck as a filter medium, forced feed being maintained by a Welmet centrifugal pump. Dilute solutions are concentrated by evaporation in a vacuum evaporator, constructed of cast hard lead. Heat is supplied by an outside steam chest operating under 15 lb. steam pressure. The solution is circulated through the steam chest by a pump of antimonial lead at a rate approximating 400 cu. ft. per min. The evaporator is evacuated by a water-jet condenser that creates a vacuum of 26 in. of mercury under normal operating conditions. The capacity of the vessel is 60 cu. ft. and the rate of evaporation 25 cu. ft. per hour.

Jan 1, 1938

THE Executive Board of The American Engineering Council met in Pittsburgh, May 26 and 27. Its actions on the licensing of engineers and on the Employment Bureau are printed at length elsewhere in this issue. The board announced plans purposing the solution of the national problems of water power and forestry, upon which "the industrial development of the nation and the standard of living of future generations largely depends. The whole Federal water-power situation is in so critical a condition that immediate constructive action by the Government to conserve the public interests, involving vast consequences of economic and Federal policy, is necessary. After a long discussion during which the water-power problem as it affects Government reorganization was reviewed and Henry Ford's Muscle Shoal's plan was discussed, the board decided to lay the entire question before President Harding. A national movement to conserve the nation's forests, in which engineers, the U. S. Forestry Service, the forestry services of the states, universities and technical schools, and other groups such as the farmers, the railroads, and lumbermen, shall pool their efforts, was set in motion by the engineers. The work will be in charge of a Reforestation Committee of the Council, headed by Charles H. MacDowell of Chicago. Mov-ing picture interests will be asked to aid. The board pledged its support to President Harding in his plan for Government reorganization. In adopting the report of its Committee on Public Affairs, headed by J. Parke Channing of New York, the Executive Board of the council determined, in the event of the failure of the President's efforts to bring about greater economy and ffieciency in national affairs by regrouping of Federal functions, to press independ-ently a nation-wide movement for the establishment of a Department of Public Works. Progress in a national survey of the two-shift day in American industries was reported by the Council's Committee on Work Periods in Continuous Industries. This survey, called the most extensive of its kind ever made, has been in progress for more than a year; and purposes an exposition of industrial conditions which shall form a basis for establishing the relative merits of three shifts of eight hours each and two shifts of twelve hours each.

Jan 7, 1922

By A. L. Holley

The first session was held in the rooms of the American Philosophical Society, on Tuesday evening, February 26th. The President, Dr. T. Sterry Hunt, called the meeting to order, and after a few introductory remarks concerning the importance of theoretical and speculative science, which often involves principles of the highest economic value, and, more than all that, serves to enlarge our conceptions of the universe, and ennoble us, by the cultivation which it affords to our most exalted faculties, proceeded to discuss some points in the chemistry of the atmosphere. It is known that there is in the crust of the earth a great amount of oxidized carbon, not only in the shape of coal, but also in the graphite or plunlbago of the crystalline rocks, in the various bituminous shales or pyroschists, which are found in all succeeding rock-formations, and also in the forms of bitumen and petroleum. All the analogies of nature lead us to conclude that these various carbonaceous substances have had an organic origin, and have been generated by the deoxidation of carbonic acid, a process effected by the growing plant, and attended with the liberation of oxygen. He showed that the carbon of a layer of coal covering the whole earth's surface to the thickness of one meter, would, in its production from carbonic dioxide, liberate an amount of oxygen equal to that now present in our atmosphere. But bituminous coal contains also a large amount of hydrogen, derived from the deoxidation of water, which implies the liberation of a farther portion of oxygen. The amount from this latter source would equal, for the various coals and asphalts, from one-eighth to one-fourth, and, for the petroleums, onehalf of that set free in the deoxidation of the carbon which these hydrocarbonaceous bodies contain. From what we know of the composition of the stratified rocks, it is probable that they include an amount of deoxidized carbon and hydrogen many times greater than that contained in a layer of coal one meter in thickness, and, consequently, that the disengaged oxygen in past ages must have far exceeded that now present in our atmosphere. To this must be added

Jan 1, 1879

By John W. Cahn, John E. Hilliard

Single crystals of copper and silicon-iron were cold rolled in orientations chosen to produce individually the major components of the poly crystalline deformation texture. The orientation dependence of the recrystallization kinetics was studied relative to the primary recrystallization textures of these specimens. It is not possible to rationalize the poly crystalline re crystallized textures on this basis. The results suggest an important role of the interaction of adjacent crystals during the deformation of aggregates. BRICK and Williamson1 first noted evidence that the recrystallization temperature was different for straight-rolled and cross-rolled copper given comparable reductions. Michalak and Hibbard2 investigated quantitatively the effect of rolling procedure on the kinetics of recrystallization of cold-rolled copper and found that material cold-rolled the same amount by straight-pass, cross-pass, and compression-pass techniques developed different deformation and recrystallization textures, different 1-hr recrystallization temperatures, and different recrystallization kinetics. However, the temperature dependence of the rate of recrystallization was essentially the same for all techniques. Similar results were obtained on iron. Dunn and Koh3 in studying the recrystallization textures of cold-rolled silicon-iron single crystals reported large differences in the annealing temperatures and times required to recrystallize specimens of different orientations cold-rolled the same amount. Liu4 and Liu and Hibbard5 utilized the concept of different recrystallization temperatures for different orientations of cold-rolled crystals to rationalize the difference in recrystallization textures found in various face-centered-cubic metals. Their explanation predicted a significant difference in the recrystallization kinetics of deformed (110) [112] crystals as compared to (358) [352] crystals, and, in fact, Liu4 reported evidence that this difference existed at least qualitatively. Verbraak6 who rolled and recrystallized a series of copper single crystals found that the double (112) [111] rolled orientation is related to recrystallized cube texture formation. The effect of rolling intensity on the relative amount of cube component suggests an important role of recrystallization kinetics. Walter and Hibbard7 while trying to relate the behavior of rolled and recrystallized single crystals of silicon-iron to the behavior of polycrystal-line silicon-iron again noted that differences in recrystallization kinetics were necessary to rationalize their results. The purpose of the present investigation was to obtain quantitative kinetic data on the recrystallization of single crystals of both copper and silicon-iron rolled to initial isolated individual orientations corresponding to those found in the polycrystalline deformation textures. These data might indicate the importance of the deformation orientation, i.e. the range of available nuclei, the deformed matrix orientation into which these nuclei grow, and the orientation dependence of their growth rate during primary recrystallization on this texture. I. COPPER Experimental Procedure—A single crystal of 99.98 pet purity copper, grown by the Bridgman technique, was purchased in the form of a bar 1 1/2

Jan 1, 1962

By C. J. Osborn

In oral discussion at the Columbus midyear meeting, September 26, 1949, these pertinent questions were asked: Was a satisfactory separation of metal and matte obtained? The matte was quite fluid and in most cases the separation was satisfactory. Were the mattes chlorinated after aging? The mattes were stored in sealed glass mason jars, and chlorina-tion experiments made after standing for several weeks gave satisfactory results. Was ferric chloride volatilized? Most of the iron content of the matte was converted to ferric chloride. However, because of the low chlorination temperatures used (150" to 250°C) the major part of the ferric chloride remained with the residue. Undoubtedly, some ferrous chloride was also formed, because of the reducing conditions within the reaction vessel, but no effort was made to separate it from the ferric chloride. Could the reaction be stopped before making metallic iron? No attempt was ever made to stop the reaction before making metallic iron. Generally, 20 to 60 pct of the iron in the charge was obtained as metallic iron which could be readily separated from the matte. In certain cases, metallic iron was dispersed through the matte in the form of globules, which could be removed by magnetic separation. Could other sulphides, i.e., calcium sulphide or sodium sulphide be used in place of iron sulphide? No other sulphides were investigated. It was felt that titanates of calcium and sodium would be formed should these sulphides be used to replace the pyrite. What were the sulphur volatilization losses during matte smelting? In the course of this laboratory investigation, a rather wide variety of variables was introduced from highly oxidizing to reducing conditions and various ratios of pyrite, rutile, and coke. These and other factors all have a definite bearing on the sulphur losses. In general, the higher the sulphur in the charge the higher were the sulphur losses and the percentage of titanium in the matte decreased. With sulphur additions more nearly the theoretical amount, the sulphur losses averaged approximately 10 to 15 pct. With a higher percentage of sulphur on the charges, the losses were in the order of 15 to 30 pct.

Jan 1, 1951

By F. C. Greene

The oil and gas industry in Missouri in 1934 continued along the same lines that have marked the previous years. One new gas pool has been opened, others have been extended and in one oil pool a 25-bbl. well was completed. Missouri has no laws or regulations relating to drilling or the filing of well logs and the Geological Survey depends on its own scouting activities to obtain information. The data herein have been taken largely from a paper by the author recently published in the 58th Biennial Report of the State Geologist of Missouri. That report is available on application to H. A. Buehler, State Geologist, Rolla, Missouri, accompanied by ten cents in stamps, the amount of the postage. The preliminary figures, subject to revision, indicate that before the end of December, 1932, there were 2495 completions, of which 320 were oil wells, 1139 were gas wells and 1036 were dry. Over half of the oil wells were drilled in the Richards-Stotesbury area of Vernon County and were pumped for only a short period of time. During the period 1933-34 there were 201 completions, of which 10 were oil wells with an initial daily capacity of 100 bbl., 90 were gas wells, with an open flow of 26,578,256 cu. ft., and 101 were dry. The most active areas in drilling for gas in 1934 were the Marota area, sec. 17, T.49N., R.32W., Jackson County, the Grandview area in T.47N., R.33W., Jackson County, and the Plattsburg area in Clinton County. The Knoche oil pool in sec. 16, T.46N., R.33W., Cass County, was the scene of the only important oil development. In the Marota pool nine wells were completed to the Squirrel sand, with a combined open flow of about 5,000,000 cu. ft. The pool is on a small symmetrical dome with a closure of at least 30 ft. The average depth of the wells is 450 ft. The Squirrel sand (Upper Cherokee, Pennsylvanian) had a thickness of 94 ft. in a near-by dry hole, but only the upper 30 or 40 ft. is drilled in the producing wells. The largest well

Jan 1, 1935

By C. M. Young

THE safety lamp is the most common and convenient apparatus for detecting inflammable gases in mines, the presence of gas being shown by a blue flame, called the cap, if the wick has been lowered to suppress the luminous flame. The height of the cap increases with the proportion of gas and with the temperature of the lamp flame. Lamps of the Wolf type, the fuel of which is benzine, have a hotter flame than lamps in which vegetable oils are used, such as the Davy, and the Clanny, and are more sensitive than the latter and their many modifications. The Piehler alcohol lamp gives a still higher cap while the Clowes hydrogen lamp is most sensitive of all. While the effect of the temperature of the source of ignition is well known, the writer knows of no previous attempt to correlate the change of this temperature with change of the height of the cap produced. In order to determine the height of the cap at various temperatures, it was necessary to have a source of ignition the temperature of which could he accurately controlled over a considerable range. This condition was met by a coil of wire of high fusing point heated by an electric current controlled by a variable resistance. The use of a coil offered the further advantage of freedom from complications due to the flame of a burning fuel. Such a flame, being itself of variable height, would to some extent raise or lower the elevation of the base of the cap and therefore add to the difficulty of determining the height of the cap. Besides this, the presence of a small cap from the lamp fuel, commonly known as the "fuel cap, " would interfere with the observation of small gas caps. After some experiment, a coil was made of platinum wire, No. 26, diameter 0.016 in. The coil was 17/64 in. (6.746 mm.) in outside diameter and had eight full turns in a length of ½ in. (12.69 mm.). This was connected to an electric circuit through an adjustable resistance, as shown in

Jan 8, 1919