Search Documents

By J. A. Fellows, Earnshaw Cook, H. S. Avery

TEe increased use of heat-resistant alloys (26 per cent Cr, 12 per cent Ni; 16 per cent Cr, 35 per cent Ni; 12 per cent Cr, 60 per cent Ni; etc.) in recent years has been accompanied by continued demands by the consumer for improvement in properties. The manufacturers of these materials, of necessity, have resorted to more critical studies of the basic causes of variations in fundamental properties. To keep pace with the need for augmented information, previous techniques of investigation have been refined and new test methods and instruments created. It is the purpose of this paper to describe the apparatus, experimental technique and precision of measurement that were employed in the exploration of properties of heat-resistant alloys presented in a companion paper. The detailed precautions in experimental procedure essential for attainment of accurate and comparable data at elevated temperatures cannot be too highly emphasized. The Creep Test Since the fundamental concepts of creep testing have been recognized for the past 20 years, present interest is restricted to refinements in equipment and experimental procedure. The creep-test iaboratory constructed for the American Brake Shoe and Foundry Co. is designed to permit I000-hr. tests in the temperature range of I200° to 2 200°F. with a choice of applied stress extending from jo to 50,000 lb. per sq. in. in increments of 50 lb. per sq. in. To simplify the calculation of weight combinations, the loading beams (Fig. I) are provided with counterweights to eliminate the tare. The precision of the knife-edges (10:I ratio) is such that a 10-gram weight placed on the upper specimen grip will be exactly balanced by a I-gram weight attached to the loading shackle. Check of the loading weights proved the maximum error to be 0.06 per cent. Axial alignment is provided by crossed knife-edges in the grip seats. The furnaces are similar in design to those of Crane and Company, Battelle Memorial Institute, and the U.S. Steel Corporation. An 80 per cent Pt, zo per cent Rh No. 19 B. and S. gauge wire is used as the heating element. The details of -construction are shown in the radiograph reproduced in Fig. 2. The windings are held in place on an alundum tube with aludum cement; the distribution of turns is adjusted to give a maximum temperature gradient of , I°F. over a 4-in. gauge length (Fig. 3). To avoid sharp temperature differentials at the ends of the test section, the length of the furnace is four times the gauge length. Sixteen-inch coupons are used „ to reduce the temperature of the threaded joints and thus to facilitate removal from the grips. Thermal losses are minimized by refractory insulators cut to shape and surrounded by diatomaceous ear,th. The taps

Jan 1, 1942

By B. W. Dyer

In 1924, the Crescent Eagle Oil Co., while drilling the salt section of the Paradox formation in Grand County, Utah, encountered a salt that did not appear to be sodium chloride. This salt was analyzed and showed the presence of potash minerals, both sylvite (KCl) and carnallite (KMgC12.6H2O). Because of the high potash content of the sample, there was considerable speculation: (I) as to whether the hole had been salted, and (2), if not, the extent, richness, and the depth at which the deposit occurred. The discovery caused a large amount of activity in the area. During the next few years, 68 potash prospecting permits were issued by the Government, 24 under the Act of 1917 and 44 under the Act of Feb. 7, 1927, each including about four sections of land. Several holes, all shallow, were drilled for potash. A number of holes were drilled for oil into the salt horizon and the cuttings collected at the oil wells were examined petrographically and chemically. The shallow test holes were not sufficiently deep to reach the potash horizon and revealed nothing of value, but several of the oil test holes gave some indication of where potash might be found. Location and Geology of Deposits The potassium and magnesium salts have been found in various places from the Denver and Rio Grande Western Railroad tracks about seven miles west of Thompsons, in eastern Utah, to Cane Creek, a tributary of the Colorado River— a distance north and south of about 35 miles. In this locality, there appear to be five separate deposits: the Crescent Eagle area, which is in T. 22 S., R. 19 E.; the Salt Valley area, in the vicinity of the north-south line of T. 23 S., between R. 20 E. and R. 21 E.; the Seven Mile area, in the eastern part of T. 25 S., R. 20 E.; the Cane Creek area, on the Colorado River, in T. 26 S. and T. 27 S., R. 20 E. and R. 21 E.; and the Salt Wash area, in T. 22 S. and T. 23 S., R. 16 E. and R. 17 E. (Fig. I.) The Crescent Eagle and Salt Valley areas are in the Salt Valley anticline, some of the wells being in the fault graben and others outside. Structurally, the Salt Valley anticline is very complex, and can be described in general terms as a northwesterly plunging collapsed anticline about 15 miles long. In the Crescent Eagle area, the valley graben is about 1 1/2 mile wide and the salt probably forms a plug, the apex of which is in the vicinity of the Crescent Eagle well. Owing to the complex structure, there has been every opportunity for flowage in the salt to cause local thinning or thickening of beds. The regular succession of formations in the general area* is: Cretaceous Mancos Dakota Jurassic Morrison Summerville Entrada Carmel

Jan 1, 1948

By B. W. Dyer

In 1924, the Crescent Eagle Oil Co., while drilling the salt section of the Paradox formation in Grand County, Utah, encountered a salt that did not appear to be sodium chloride. This salt was analyzed and showed the presence of potash minerals, both sylvite (KCl) and carnallite (KMgC12.6H2O). Because of the high potash content of the sample, there was considerable speculation: (I) as to whether the hole had been salted, and (2), if not, the extent, richness, and the depth at which the deposit occurred. The discovery caused a large amount of activity in the area. During the next few years, 68 potash prospecting permits were issued by the Government, 24 under the Act of 1917 and 44 under the Act of Feb. 7, 1927, each including about four sections of land. Several holes, all shallow, were drilled for potash. A number of holes were drilled for oil into the salt horizon and the cuttings collected at the oil wells were examined petrographically and chemically. The shallow test holes were not sufficiently deep to reach the potash horizon and revealed nothing of value, but several of the oil test holes gave some indication of where potash might be found. Location and Geology of Deposits The potassium and magnesium salts have been found in various places from the Denver and Rio Grande Western Railroad tracks about seven miles west of Thompsons, in eastern Utah, to Cane Creek, a tributary of the Colorado River— a distance north and south of about 35 miles. In this locality, there appear to be five separate deposits: the Crescent Eagle area, which is in T. 22 S., R. 19 E.; the Salt Valley area, in the vicinity of the north-south line of T. 23 S., between R. 20 E. and R. 21 E.; the Seven Mile area, in the eastern part of T. 25 S., R. 20 E.; the Cane Creek area, on the Colorado River, in T. 26 S. and T. 27 S., R. 20 E. and R. 21 E.; and the Salt Wash area, in T. 22 S. and T. 23 S., R. 16 E. and R. 17 E. (Fig. I.) The Crescent Eagle and Salt Valley areas are in the Salt Valley anticline, some of the wells being in the fault graben and others outside. Structurally, the Salt Valley anticline is very complex, and can be described in general terms as a northwesterly plunging collapsed anticline about 15 miles long. In the Crescent Eagle area, the valley graben is about 1 1/2 mile wide and the salt probably forms a plug, the apex of which is in the vicinity of the Crescent Eagle well. Owing to the complex structure, there has been every opportunity for flowage in the salt to cause local thinning or thickening of beds. The regular succession of formations in the general area* is: Cretaceous Mancos Dakota Jurassic Morrison Summerville Entrada Carmel

Jan 1, 1948

By J. A. Fellows, Earnshaw Cook, H. S. Avery

THE increased use of heat-resistant alloys (26 per cent Cr, 12 per cent Ni; 16 per cent Cr, 35 per cent Ni; 12 per cent Cr, 60 per cent Ni; etc.) in recent years has been accompanied by continued demands by the consumer for improvement in properties. The manufacturers of these materials, of necessity, have resorted to more critical studies of the basic causes of variations in fundamental properties. To keep pace with the need for augmented information, previous techniques of investigation have been refined and new test methods and instruments created. It is the purpose of this paper to describe the apparatus, experimental technique and precision of measurement that were employed in the exploration of properties of heat-resistant alloy presented in a companion paper.? The detailed precautions in experimental procedure essential for attainment of accurate and comparable data at elevated temperatures cannot be too highly emphasized. THE CREEP TEST Since the fundamental concepts of creep testing have been recognized for the past 20 years, present interest is restricted to refinements in equipment and experimental procedure. The creep-test laboratory constructed for the American Brake Shoe and Foundry Co. is designed to permit 1000-hr. tests in the temperature range of 1200° to 2200°F. with a choice of applied stress extending from 50 to 50,000 lb. per sq. in. in increments of 50 lb. per sq. in. To simplify the calculation of weight combinations, the loading beams (Fig. I) are provided with counterweights to eliminate the tare. The precision of the knife-edges (10.1 ratio) is such that a 10-gram weight placed on the upper specimen grip will be exactly balanced by a 1-gram weight attached to the loading shackle. Check of the loading weights proved the maximum error to be 0.06 per cent. Axial alignment is provided by crossed knife-edges in the grip seats. The furnaces are similar in design to those of Crane and Company, Battelle Memorial Institute, and the U.S. Steel Corporation. An 80 per cent Pt, 20 per cent Rh No. 19 B. and S. gauge wire is used as the heating element. The details of construction are shown in the radiograph reproduced in Fig. 2. The windings are held in place on an alundum tube with alundum cement; the distribution of turns is adjusted to give a maximum temperature gradient of ± 1°F. over a 4-in. gauge length (Fig. 3). To avoid sharp temperature differentials at the ends of the test section, the length of the furnace is four times the gauge length. Sixteen-inch coupons are used to reduce the temperature of the threaded

Jan 1, 1942

By Michael Tenenbaum

Selected characteristics of nonmetallic phases were determined in low-carbon sheet steels which had been produced by various refining; deoxidizing, and casting procedures. The results showed little influence of the refining process on the quantity, distribution, size, and character of the nonmetallic phases. The quantity of inclusions was governed by the deoxidation procedures. While the mode of casting influenced the internal structure and the pattern of inclusion distribution, it had little effect on the quantity of nonmetallics. The vast majority of inclusions were under 30 µ in diam, and there was little change in size distribution during hot and cold rolling. The composition and structure of the inclusions were expained an the basis of known equilibrium phase diagrams for the appropriate systems. Additional work is needed to explain some of the observations of this paper. HENRY Marion Howe's contributions to the metallurgical profession include his many writings, the wisdom that he imparted to his students, and the inspiration that he gave to the many scholars, teachers, and industrialists who knew him personally. It was Professor Howe's intimate colleague, Albert Sauveur,1 who, in the first Howe Memorial Lecture, could have been speaking for the metallurgist of our generation as well as his own when he wrote, "...how many of us on the point of going astray were called back to the right path by Howe's guiding torch?" More than a quarter of a century later, Francis Foley,2 one of the last in the Howe Lecture series who worked directly with the great man, delivered the ultimate tribute, "...truth, in its time is so hard to identify." While Professor Howe strove to be right, "he was content if he provoked the reader to take the next step along the path to greater knowledge." Like so many of my predecessors, I sought guidance for this lecture by referring to Professor Howe's two classic texts, Metallurgy of steel,3 and Metallography of Steel and Cast Iron: the former book interpreting the facts as he saw them near the start of his career, and the latter—published 26 years later—pointing to many fertile fields for metallurgical investigation. Those of us who harvest the fruits of Henry Marion Howe's contributions to the metallurgical profession now look with wonder at the tremendous legacy he has provided. It is rewarding to study his writings and to recognize the anticipation of such aspects of modern ferrous metallurgy as: 1) Direct reduction 2) Steelmaking reactions 3) The approaches and benefits of degassing 4) Solidification mechanisms 5) Habits and behavior of nonmetallic inclusions 6) Recrystallization phenomena 7) Slip and slip propagation 8) Dislocations 9) Discontinuous deformation 10) Microscopic and macroscopic segregation

Jan 1, 1970

By W. F. Flanagan, K. R. Evans

The strong temperature dependence of the flow stress of bcc metals has prompted considerable interest and controversy concerning the rate-controlling influence of the Peierls' mechanism upon deformation in metals.18"21 Dorn and Rajnak" recently offered a criterion for Peierls' deformation utilizing a line-energy model of a dislocation to estimate the saddle-point activation energy, for the nucleation of a pair of kinks as a function of applied stress and the height and shape of the peierls9- barrier. It was found that Un/2Uk, where 2Uk is the excess energy of a kink pair, was a unique function of where is the effective stress and 7p is the Peierls' stress as defined in Fig. 20. The relationship found by Dorn and Rajnak between is given by the solid line of Fig. 21. may be expressed in terms of the temperature of test, T, and the athermal temperature, T,, defined in Fig. 20. Considering the strain-rate, 9, of deformation for a thermally activated process to be given by where fo is nearly a constant, it is seen that and the theoretical relationship of Fig. 21 may be examined with readily obtainable experimental parameters. Dorn and Coworkers analyzed a large amount of experimental data in this manner for materials sus-

Jan 1, 1967

By J. E. Burke, C. W. Mason

IN attempting to study precipitation from a tetragonal lattice using solid solutions of bismuth in tin, it was found that although a Widnmanstatten pattern is observed 1 only a qualitative analysis of the orientation relationships is possible, because of the unusual structural changes that accompany the precipitation process MICROSCOPICAL STUDIES Alloys were made from Chempur tin (Standard samples 42b and 42c, National Bureau of Standards), and bismuth (Kahlbaum C P ) by melting neighed quantities together under palm oil, stirring well, and casting in a heated graphite mold The polishing and etching techniques employed largely govern the visibility of the structural changes The preliminary surfacing operations were similar to those recommended by Villela and Bergekoff,5 through BehrManning 3/o abrasive papers, lubricated by a solution of paraffin in kerosene A rough metallographic polish was next given, using a thin cotton cloth charged with relevigated alumina (maximum particle size of about 4µ) and soap solution, repeated etching and polishing served to remove disturbed metal For high-power examination better preparation was necessary It was found that on such soft metals the threads of the fabric, rather than the abrasive, cause most of the scratching Cotton outing flannel, which had been brushed so that the nap lay down, was fairly satisfactory, but a Heavy grade of silk velvet (not the noncrushable kind) was found to be better, especially after some use A better procedure was as follows The metal lap was warmed slightly, and a 4-in circle of woolen broadcloth was cemented to its center by a thin film of melted paraffin The broadcloth was then moistened with water, and a 30 to 40 per cent solution of sodium hydroxide heated to about 50°C was poured over it, allowed to stand for 1 to 2 min and then washed off It was neither necessary nor desirable to remove all the sodium hydroxide from the cloth, since its etching action aided in the removal of the flowed layer from the sample The cloth was then charged with a paste of the relevigated alumina in water Since this lap did not remove deep scratches, it was necessary previously to polish the specimen on some material such as the silk velvet The sodium hydroxide softens and partly gelatinizes the woolen lap covering, permitting a scratch-free polish, but its action continues, and the cloth deteriorates after about 24 hr This is not serious, because a new lap can be prepared in about 5 min, and only small pieces of cloth are used Etching with a strongly acid solution of ferric chloride was found satisfactory for removing the flowed layer For the final etching, the most satisfactory reagent was that of Taffs,7 the formula for which is FeC13 6H20, 2 grams, HC1, 5 c c , H2O, 30 c c , C2H5OH (95 per cent), 60 c c This etchant reveals differences in com-

Jan 1, 1941

||Abad, Leopoldo F, Min Engr, Div of Mines, Bureau of Science Manila, P I '23 Abadilla, Quirico A, Geol , Logo Pet Corp Box 172, Maracaibo, Venezuela '20 ||Abarquez, Ramon F, Met, Bureau of Science Manila, P I '24 ||Abbey, Robert Graham, Student, Case School of Applied Science Cleveland, Ohio '21 Abbott, A N , Mines Supt, Mazapil Copper Co, Ltd Concepcion del Oro, Zac , Mexico '23 Abbott, Clarence E , Mgr, Mines & Quarries, Tenn Coal, Iron & R R Co. 1242 Brown Marx Bldg, Birmingham, Ala '04 Abbott, Louis Benjamin, Chief Engr, Consolidation Coal Co, Elkhorn Div Jenkins, Ky '15 Abbott, Robert R , Met Engr, Peerless Motor Car Co Cleveland, Ohio '12 ||Abbott, Wells Osborn, Ray Consolidated Copper Co Hayden, Ariz '23 Abeel, George H., Jr, Cons Min Engr 4612 W 17th St, Los Angeles, Cal '18 Abel, Albert E , Asst to Pres , Valley Mould & Iron Corp Sharpsville, Pa '19 Abernathy, George Elmer, Prof of Geol & Min , Kansas State Teachers College, Pittsburg, Kan '20 Abey, Hiroshi, Min & Met Engr, Chief Engr, Takata Min Co, 2 Yeirakucho, Nichome, Kojlmachiku, Tokyo, Japan '17 ||d'Ablamg, Philip R , Millman, Old Dominion Silver-Lead Co Ellensburg, Wash '25 Aborn, R H, X-Ray Metallographic Research, Mass Inst of Tech Cambridge, Mass '19 Abouchar, Sylvain Sley, Min Engr & Geol, care of S H Sekaly, 13 Rue El Nimr.

Jan 1, 1923

Allan Gibb, Mount Perry, Queensland, Australia (communication to the Secretary):—In drawing conclusions from his observations, Mr. Van Liew has apparently overlooked the reduction in weight that takes place in the content of the converter. The percentage-compositions of the matte, etc., are not directly comparable for determining the rate of elimination of the impurities; and, in the absence of exact weights (which in such an operation could not be obtained), it is necessary to determine the relation between the impurities and the copper with which they are combined at various stages, in order to get data that are comparable. Owing to a portion of the copper being removed in the slag, etc., the weight of copper in the converter is not a fixed quantity, but.it is sufficiently approximate to permit very reasonable comparison. The analytical data given by Mr. Van Liew, reduced to this basis (a ratio between the impurities and the copper with which they are combined), are shown in the table on page 958. From this table it will be evident that Mr. Van Liea's conclusions as to the source of heat at digerent stages are not quite correct. During the first 10 minutes, no iron is scorified, the heat being derived from the oxidation of the sulphur, of which 7 per cent. of the total is removed in this time. Prom

Jan 1, 1904

[A Aall, Christian H., M49 B VP, Dir of Smelt & Refin, Am. Metal Climax Inc., 1270 Ave. of the Americas, N.Y. Aaroe, Stanley L., A54 B VP, The W. S. Tyler Co. of Can. Ltd., St. Catharines, Ontario, Canada Abalos, Toodulo Q., J57 A Prod Foreman, Lepanto Cons. Mng. Co., Mt. Province, Philippines Abbass, G., M55 P. O. Box 680, Hong Kong, China Abbitt, James M., A54 770 Sole Blvd., Bartow, Fla. Abbott, Raymond C., J59 3442 Greenwich Ave., Columbus 24, Ohio Abdullah, N. Y., J53 Dept. of Mines, Res. Div., P. O. Box 1016, Tiger Lane, Ipoh Perak, Malaya Abel, John F., Jr., J53- 100 Maple, Littleton, Colo. Abell, Leo M., M31 B Conc Supt, Phelps Dodge Corp., Morenci, Ariz. Abendroth, Harry E., A57 A Geol, Union Carbide India, 183 Brabourne Rd.. Calcutta. India]

Jan 1, 1961

By Henry Howe

1. Introduction.-This paper is based in large part on the examination of two rings, shown in section in Fig. 4 to 15, cut from an eroded 14-in. (35.56-cm.) gun, liner, and containing, according to Booth, Garrett, & Blair: Carbon, 0.380 per cent.; manganese, 0.655 per cent.; nickel, 2.810 per cent.; vanadium, 0; chromium, a few hundredths of 1 per cent.; tungsten, 0; molybdenum, 0. These rings were received from Admiral Joseph Strauss, then Chief of Ordnance, U. S. Navy, through the kindness of Mr. Hudson Maxim, Chairman of the Committee on Ordnance and Explosives,, of the U. S. Naval Consulting Board.

Jan 2, 1918

By J. P. Smith

DURING the winter of 1946 to 1947 potash operations in Germany, France and Spain were visited by the author. The U. S. Department of Commerce, through its Field Intelligence Agency Technical, sponsored the inspection of German properties by representatives of the American Potash Industry. Vast deposits of potash salts occur in the above-mentioned countries, and the production and marketing of these salts are important in their respective economies. Germany An area of some ten thousand square miles of north central Germany is underlain by lenses of potash salts interbedded with greater thicknesses of sodium chloride or common salt. These salt measures are relict deposits from the evaporation of an arm of the Zechstein (Permian) Sea which formerly covered northern Europe. During the peak year of 1940, Germany produced salts containing 1,860,000 tons of K,O and, next to coal, potash is its most important mineral raw material. The German deposits are found in the synclinal areas flanking the Flechtingen, Hartz Mountain and Thuringian uplifts, and, to the north they lie beneath the plains of Hannover. The regional dip of the salt measures is to the north, hence, lenses of potash found at depths of 500 to 1000 m* in the Two general depositional provinces of potash concentrations are recognized: (1) the main basin, and (2) the subsidiary basin. The main basin embraces the producing districts of Stassfurt, Sud Hartz, Halle, and Hannover-Braunschweig. From J. P. SMITH, Member AIME, is Clzief Geologist, U. S. Potash Co., Carlsbad, New Mexico. New York Meeting, February 1948. TP 2621 H. Discussion of this paper (2 copies) may be sent to Transactions AIME before Feb. 28, 1950. Manuscript received May 26, 1948. 40 to 45 pct of the German production comes from this basin. The Werra-Fulda district, producer of 50 pct or more of the German potash, lies in the subsidiary basin. Salt Stratigraphy: Five commercial potash zones or beds are recognized. The three beds present in the main basin are: The Stassfurt bed that occurs near the top of the older salt, and the Ronnenberg and Riedel beds in the younger salt occurring 200 to 300 m, respectively, above the Stassfurt bed. The Stassfurt bed is found over the entire main basin, while the Ronnenberg and Riedel are restricted to the Hannover area. Two potash beds occur in the Werra basin. These are the Thuringian, or lower bed and the Hessen or upper potash bed that occurs 60 m above. These beds lie 210 and 150 m, respectively, below the position of the Stassfurt bed, and are restricted to the Werra basin. The upper bed is 2.5 to 11.5 m in thickness, and the principal ores are hartsalz with varying thicknesses of carnallite. The lower bed averages 3 m in thickness, and contains hartsalz. The upper bed is presently being mined, and the

Jan 1, 1951

By J. P. Smith

DURING the winter of 1946 to 1947 potash operations in Germany, France and Spain were visited by the author. The U. S. Department of Commerce, through its Field Intelligence Agency Technical, sponsored the inspection of German properties by representatives of the American Potash Industry. Vast deposits of potash salts occur in the above-mentioned countries, and the production and marketing of these salts are important in their respective economies. Germany An area of some ten thousand square miles of north central Germany is underlain by lenses of potash salts interbedded with greater thicknesses of sodium chloride or common salt. These salt measures are relict deposits from the evaporation of an arm of the Zechstein (Permian) Sea which formerly covered northern Europe. During the peak year of 1940, Germany produced salts containing 1,860,000 tons of K,O and, next to coal, potash is its most important mineral raw material. The German deposits are found in the synclinal areas flanking the Flechtingen, Hartz Mountain and Thuringian uplifts, and, to the north they lie beneath the plains of Hannover. The regional dip of the salt measures is to the north, hence, lenses of potash found at depths of 500 to 1000 m* in the Two general depositional provinces of potash concentrations are recognized: (1) the main basin, and (2) the subsidiary basin. The main basin embraces the producing districts of Stassfurt, Sud Hartz, Halle, and Hannover-Braunschweig. From J. P. SMITH, Member AIME, is Clzief Geologist, U. S. Potash Co., Carlsbad, New Mexico. New York Meeting, February 1948. TP 2621 H. Discussion of this paper (2 copies) may be sent to Transactions AIME before Feb. 28, 1950. Manuscript received May 26, 1948. 40 to 45 pct of the German production comes from this basin. The Werra-Fulda district, producer of 50 pct or more of the German potash, lies in the subsidiary basin. Salt Stratigraphy: Five commercial potash zones or beds are recognized. The three beds present in the main basin are: The Stassfurt bed that occurs near the top of the older salt, and the Ronnenberg and Riedel beds in the younger salt occurring 200 to 300 m, respectively, above the Stassfurt bed. The Stassfurt bed is found over the entire main basin, while the Ronnenberg and Riedel are restricted to the Hannover area. Two potash beds occur in the Werra basin. These are the Thuringian, or lower bed and the Hessen or upper potash bed that occurs 60 m above. These beds lie 210 and 150 m, respectively, below the position of the Stassfurt bed, and are restricted to the Werra basin. The upper bed is 2.5 to 11.5 m in thickness, and the principal ores are hartsalz with varying thicknesses of carnallite. The lower bed averages 3 m in thickness, and contains hartsalz. The upper bed is presently being mined, and the

Jan 1, 1951

By George A. Miller

ALTHOUGH the Andean mountain belt, which contains almost all the metal deposits of the other South American nations, does not enter Brazil, this country is rich in mineral resources, for in area it accounts for half the continent and geologically it contains almost all of the Brazilian Shield. This great mass of ancient rocks has been relatively stable for a long time and forms a great area of plateaus and highlands interrupted only by the syncline which carries the Amazon River across it to the sea. Lowland Brazil - the great flood plains of the Amazon. Tocantins, Paraguay, and Parana Rivers-is of no interest to the miner, and in fact supports but a small proportion of the country's population. The highland area is divided into unequal parts by the Amazon River; the north half is underlain by the north lobe of the Brazilian Shield which extends into Venezuela as far as the Orinoco, and into the Guianas, and is known as the Guiana Highlands. Mineralization appears to have been weak in the Brazilian portion of these hills. In fact most of the ore deposits are to be found in the States of Minas Gerais and Bahia, although the neighboring states of Sao Paulo, Pernambuco, and Piauhy can also boast of some deposits. Goias and Matto Grosso are as yet incompletely prospected but are considered to contain reserves for the future.

Jan 1, 1945

By George A. Miller

AMERICANS like engines, but more than anything they like powerful engines, and next to that they want them quiet, silent, smooth; perhaps a slight purr might be permitted, but they must not knock. To provide a gasoline to fit all these requirements, American petroleum technologists have experimented for years, and mounting octane numbers of the gasolines the refiners have produced both before and during the war bear witness to their success. The question on everyone's mind now is what may we expect in the way of engine fuel in the postwar period? The gasoline drouth during the war rationing, the inconvenience of doing without a car were major annoyances to all motorists, but they put up with them pretty cheerfully for the most part. However, now that the war is over, and the jalopies are all out and the better cars have been taken off the jacks and brought out on the road, the call is for "Some of that good gas-fill her up, if you please."

Jan 1, 1945

By L. F. Bishop

The ore bodies of the Butte district1 are found in many different vein systems having many different structural characteristics; some are narrow with self-supporting ore but with weak walls; some are wide with weak or strong ore and weak walls; some of the veins dip steeply and others do not; some have well defined walls, and others, in the "horsetail" area, are mined to sample limits. Consequently, many types of stoping methods are used in mining these ores. The stoping methods used in the Anaconda Copper Mining Company's properties are the square-set and cut-and-fill. The square-set method is the principal stoping method used because, generally speaking, the ore and walls are weak, the ore is high grade, and good extraction is required. These square-set stopes may be classified as conventional, vertical slice, slot, timber rill, and Mitchell slice types. The conventional type square sets are those of various shapes and sizes, mined by horizontal slicing to the boundaries of the stopes. The rock is slid to the chute and the filling is moved by gravity. The ore and waste may be handled with a scraper when local conditions require it. The vertical-slice square-set system is the type used in narrow veins that are mined in vertical panels. The slot stopes are stopes in wide veins that employ a slot across the vein instead of a con- ventional chute to handle the ore. The timber rill is a type of square set in which the ore is mined as in inclined cut and fill but the square-set timber is used. The Mitchell slice is the type used for some broken or heavy ore blocks, or for pillar extraction between two converging slot stopes. The cut-and-fill method is used where the ore will stand without much support although the walls may be weak. The principal type of this method is the horizontal cut-and-fill, with mechanical scraping. The inclined cut-and-fill, or rill, stopes are used in some veins too narrow for scraping. The production from the various methods in use for the second six months of 1944 are shown in Table I. This paper deals mainly with the vertical slice and slot types of square-set stoping, because of their effect on production locally and their potential possibilities here and in other districts, with sufficient reference to conventional square-setting for comparison.

Jan 1, 1946

Aamot, Olav Crone, (M'29) Chem. Engr., Elektro¬kemisk, Raadhusgt, 23; Oslo, Norway. Abadilla. Quirico A., (M'33) Min. Engr., Dir., Bureau of Mines, Manila, P. I. Abbott, Agatin T., ( J'40) Asst. Geol., Trench Mine, Patagonia, Ariz. Abbott, Clarence E., (M'04) Civil Engr., V.P., Tennessee Coal Iron & R. R. Co.. 159'3 Brown Marx Bldg.. Birmingham, Ala. Abel, Raymond L., (M'28) Chem. Engr., Chief of Inspection Div., Pittsburgh Chem. Warfare Pro¬curement Dist., American Batik Bldg., Pitts¬burgh. Pa. Abel, Walter D., (M'32) Min. Engr.. Div. of Cor¬porations, State of Calif.. 403 California State Bldg., Los Angeles, Calif. Abele. Louis T., (M'31) 4800 Patterson Ave.. Richmond, Va. Abell, Leo M., (M'311 Research Met., Mount Mor¬gan Ltd., Mount Morgan, Queensland, Australia. Abenius, Hakan V., (M'37) c/o Falu Gruva, Falun, Sweden. Abernathy. G. E., (M '33S) Geol., Kansas State Geol. Survey. Pittsburg, Kan. Abernathy, Jack. H.. (M'40) Chief Engr., Sunray Oil Co.. Philtower B1dg., Tulsa. Okla. Ahorn, Robert H., (M'19) Asst. Met., Research Lab., U. S. Steel Corp., Lincoln Highway, Kearny, N. J. Abraham, A. W., (M'30) Petr. Engr., Richfield Oil Corp., 555 S. Flower St., Los Angeles. Calif. Abramowitz, William L., (J'40) Chem., National Oil Products Co., Harrison, N. J. Abrams, Charles Jackson, (M'36) Gen'l Supt., Climax Molybdenum Co.; Climax, Colo. Abstein, Henry T., (M'27) Yellow Pine, Idaho. Ackerman, D. E., (M'35) McKinsey & Co., 2 Wall St., New York, N. Y. Ackerman. E. Dumont, (A'3S) Petr. Geol.. Dist. Geol., Quiriquire' Dist., Standard Oil Co. of Venezuela, Caripito, Venezuela.

Jan 1, 1941

By G. Cartaud, F. Osmond

WE have already devoted two previous memoirs to this question. In the first we collated and discussed the existing literature on the subject; in the second, we described the crystalline forms obtained by the reduction, at different temperatures, of ferrous chloride by hydrogen or by zinc-vapor. The conclusion from these researches was that the three allotropic states of iron-a, stable below A2; 19, stable between A2 and A3; and 7, stable above A3-all crystallize in the cubic system. The differences observed were such as are customarily encountered in the crystallographic records of many minerals of which allotropic varieties or isomerides are not known, but did not conform to the ordinary definition of polymorphism. It is, however, improbable that allotropic transformations, which are placed beyond doubt by a series of positive facts, do not involve some changes in the intimate structure. As a matter of fact, the crystals we did obtain were too small to allow of a precise examination, and this might introduce an element of uncertainty in the firm establishment of our conclusions. Professor H. Le Chatelier was even led to think from some of our results that iron could very well be a rhombohedron simulating a cube, and not a true cube, and it will be remembered that the crystalline form of bismuth was for a long time incorrectly regarded as cubic. Allotropy does not, however, necessarily involve such a deduction. Without departing from the cubic system at all, a whole

Nov 1, 1906

By Tenney, J. B.

DEVELOPMENT of complex ores in the south- western part of the Rocky Mountain region has been retarded by the prohibitive distance to the nearest suitable zinc treatment plants. In the north- western and central Rocky Mountains the building, cluring tlie past decade, of electrolytic zinc plants at Anaconda, Great Falls, Trail, and Burke has tremendously stimulated the mining and exploiting of such .ores, greatly increasing the production of lead, zinc, copper, gold, and silver. Selective flotation permits the making of high-grade led, copper, and zinc concentrates. If the zinc concentrates could be made free from lead, copper, gold, and silver, they could be shipped economically to Mid- Western retort plants designed for such concentrates. Unfortunately a considerable proportion of the precious metal content accompanies the zinc blende in the ores of this region. Although some of it is saved in 'retort residues, the treatment cost is thereby increased so materially and the proportion saved so small, that .concentrates of ordinary grade cannot stand treatment charges and freight.

Sep 1, 1928

By C. S. Barrett, D. F. Clifton

THE transformation that occurs in lithium and its solid solutions containing magnesium1,2 is similar in many respects to other diffusionless transformations of the martensitic type. This general similarity makes it desirable to investigate the transformation curves in detail. The current interest in the phenomenon of stabilization in martensitic transformations has created a need for a careful appraisal of possible stabilization effects in both cooling and heating transformations in lithium alloys. The effect of prior heat treatment on the temperature at which transformation begins and the effect of various temperature cycles in partially transformed alloys also merit attention. Limited data on some of these features were presented previously,' but the present studies have been made with improved apparatus, in which erratic fluctuations were smaller than in the earlier work, and include many independent determinations of certain critical observations. Material and Methods Geiger counter X-ray spectrometers were used: a Norelco instrument, original model, and a General Electric XRD-3. The low-temperature specimen holder has been described elsewhere." Specimens 10 mm in diam and 1.5 mm thick were held in firm contact with a copper block which was attached to the lower end of a stainless steel tube that extended up to a reservoir of liquid nitrogen. A heating coil on the tube permitted a controlled temperature gradient along the tube, so that desired temperatures and rates of heating and cooling could be obtained by controlling the heating current. The specimen was surrounded by an atmosphere of evaporated nitrogen in an insulated chamber having double cellophane windows. The temperature of the specimen was read by a thermocouple imbedded in it close to the irradiated area; the specimen could be held at constant temperature within 1°C for long periods. The body-centered cubic 200 reflection near 8 = 26" was used as the index of the amount of b.c.c. material present; occasional checks were made using the most suitable line of the low-temperature phase, the close-packed hexagonal 110 line near 8 = 29". Copper radiation was used throughout. A continuous record was made of the reflected intensities on a strip chart recorder, both when the peak intensity of a line was being followed and when the lines were being scanned at constant temperature. On the continuous recordings of peak intensity, periodic checks were made on the background intensity between the lines, and on the setting of the spectrometer for maximum intensity. The lithium-base solid solution containing 12.4 atomic pct Mg (33.3 wt pct) that had been used previously' was chosen, as it had a transformation range at relatively high temperatures, so as to permit wide temperature cycling within the range. Just prior to use a pellet was cut from the ingot,

Jan 1, 1951