Search Documents

R. F. WOOD,* Sandusky, Ohio.-I made a few tests of gun-metal specimens, after I noticed the results on quenching -reported by the Bureau of Standards. The data of one such test are given herewith. The bars were heat treated and quenched before they were machined, and in all cases they were brought up to 700° or 800°. They became extremely brittle,, showed almost no elongation, except such as was caused by the failure of the pieces to fit together after they were pulled, and the tensile stength was reduced from around 35,000 to about 13,000 lb. per sq. in. In addition, the weakening effect of the quenching seemed to be almost as marked when the bar was allowed to slowly air-cool from red to black, and then quenched, as it was by quenching directly from the red heat. Test Bars.-Rough size, 9/16 in. diam. over test section, grips 13/16 in. diam. Cast two in a flask, one on each side of a block 8 by 4 by 1 in. and fin-gated thereto from the grips but not from the test section. Poured with flask in inclined position, with gate to lower end of block and riser from upper end of each test bar. Bars were machined to ½ in. over the test section, after heat treatment. Casting the Bars.-Charge of 1500 lb. consisting of 400 lb. of new metals and 1100 lb. of G turnings and scrap was melted in open-flame oil furnaces and then poured into a 1-ton ladle. From the ladle 150 lb. was poured into a preheated No. 50 crucible, land from this the flasks of test bars were poured. The six flasks are indicated below by the numbers 1 to 6 and the bars in each flask by the letters a and b, thus 4a and 4h, for instance, were the two bars in flask No. 4.

Jan 12, 1919

By G. Derge, Ling Yang, G. M. Pound

The specific conductance and its temperature dependence were measured over the entire composition range of the molten Cu2S-CuCI system. At a typical temperature of 1200°C, 10 rnol pet of the ionically conducting CuCl reduced the specific conductance from about 77 ohm-lcm-l for pure Cu2S to about 32 ohm -1cm -1, and 50 mol pet CuCl reduced the conductance to that for pure CuCI—about 5 ohm 1cm1. The nature of electrical conduction in molten Cu2S, FeS, CuCI, and mixtures was studied by measuring the current efficiency of electrolysis at about 1100°C. The Cu2S, FeS, and mattes were found to conduct exclusively by electrons, but addition of 1 5 wt pet CUS to Cu2S produces a small amount of electrolysis. Addition of CuCl to Cu2S suppresses electronic conduction, and ionic conduction reaches almost 100 pet at a CuCl concentration of about 50 mol pet. These facts are interpreted in terms of electron energy level diagrams by analogy to the situation in solids. RESULTS of electrical conductivity studies on molten Cu-FeS mattes as a function of composition and temperature have been reported.' The specific conductances ranged from about 100 ohm-' cm-' for pure Cu2S to 1500 ohm-' cm-1 for pure FeS. This is in sharp contrast with the low specific conductance of molten ionic salts for which the transfer of electricity is by migration of ions in the field. In general, these ionically conducting molten salts, such as NaC1, KC1, CuC1, etc., have a specific conductance of the order of magnitude of 5 ohm-' cm-'. It was concluded on the basis of this evidence that molten FeS and Cu,S exhibit electronic conduction. Pure molten FeS has a small negative temperature coefficient of specific conductance, resembling metallic conduction, while pure molten Cu2S has a small positive temperature coefficient, resembling semi-conduction. The molten Cu2S-FeS mattes follow a roughly additive rule of mixtures, both with respect to specific conductance and temperature coefficient. Savelsberg2 has studied the electrolysis of molten Cu2S and Cu2S + FeS. He concluded that while molten Cu2S is an electronic conductor, there is some ionic conduction in molten Cu2S + FeS3 owing to the formation of the molecular compound 2Cu2S.FeS and its dissociation into Cu1 and FeS2-1 ions. The present work does not verify his results. Chipman, Inouye, and Tomlinson" have studied the specific conductance of molten FeO and report a high specific conductance, about 200 ohm-1 cm-1 of the same order of magnitude as that found for molten mattes, and a positive temperature coefficient. They interpret these results in terms of p-type semiconduction in the ionic liquid by analogy to the situation in solid FeO.1 imnad and Derne' detected appreciable ionization in molten FeO by means of electrolytic cell efficiency measurements. In order to verify the conclusion that electrical conduction in molten Cu2S and mattes is electronic, and to gain further insight into the structure of molten sulfides, the following investigations were carried out in the present work: 1) The specific conductance, s of the molten system Cu2S-CuC1 was measured as a function of temperature over the entire composition range. As discussed later, molten CuCl is an ionic substance. It was thought that if molten Cu2S were simply ionic in nature, addition of small amounts of CuCl might not have a catastrophic effect in lowering the high conductance of the Cu2S. On the other hand, if much electronic conduction occurs, addition of the ionic CuCl should have a large effect in destroying the electronic conduction. 2) The electrolytic cell efficiency of the following molten systems was measured at about 1100°C in specially designed cells: Cu3; Cu2S + FeS, 50:50 by wt; FeS; Cu2S + CuS, 15 wt pet; Cu2S + CuC1, 5.9 to 46.4 mol pet; and CuC1. This gives a direct measure of the fraction of current carried by ions in these melts. Further, the cell efficiency, extrapolated to zero ionic current, is given by cell efficiency = (s leasile + s elexstronic). [1] s lucile for molten CulS would be expected to be no greater than that for molten CuC1, whose s lonle is about 5 ohm-' cm-1, as will be seen in the following. u,.,,.,.,.......for molten Cu,S is of the order of 100 ohm-' cm-'.' Thus, a large increase in cell efficiency from 0 to values of 10 to 100 pet upon addition of CuCl to Cu2S would indicate destruction of the electronic conductance. Conductance Measurements Experimental Procedure—The apparatus and experimental method were the same as those described in detail in connection with the study of electrical conduction in molten Cu,S-FeS mattes.' A four terminal conductivity cell and an ac poten-

Jan 1, 1957

By George F. Becker

A Nere record of Emmons's professional career would very inadequately represent the man. That he was eminent mc know, and our successors will realize in due time; but they must depend upon us for knowledge of a singularly ~vholesome, modest, unselfish personality, and of a character that did honor to a profession in which trustworthiness is indispensable. Those members of the Institute who met Emmons are his friends, and I never knew .one of these who was not the better for that friendship. Emmons was born in Boston, Mar. 29, 1841, the son of Xathaniel H. and Elizabeth (Wales) Emmons, and was named Samuel Frankliri after an ancestor who was of the sarne family as Benjamin Franklin. He took the degrcc of Bachelor of Arts at Harvard in 1861, and soon afterwards went abroad to complete his education. From 1862 to 1864 he attended the courses at the fieole Impkriale des Mines at Paris, Elie de Beaumont arid Daubrke being among his professors. The year 1864-1865 he spent at Freiberg under Cotta and other famous teachers; after which he spent another year in traveling through Europe. Like many other renowned geologists, he approached his ultimate profession from its economic side, and was thus from the first imbued with a sense of high responsibility in the promulgation of scientific opinions or conclusions. With hypotheses which were interesting merely because they were ingenious or even plausible, he would have nothing to do. In 1867 he joined the Geological Exploration of the Fortieth Parallel at its organization under Clarence King, serving at first as a volunteer, but soon receiving a regular appointment. This expedition was the first one of purely geological character sent out by the United States government. As Emmons has shown in his admirable presidential address on " The Geology of Government Explorations," its work was founded on a com-

Jan 1, 1912

By Leon Nelson

SEVERAL factors which affect the segregation and solidification of killed hot-topped steel ingots are: (1) pouring temperature, (2) volume in the hot top, (3) taper in the ingot, (4) pouring rate by varying the nozzle size, (5) segregation of several elements, (6) moving ingots before completely solidified. In most of this discussion, segregation will be measured in terms of carbon variation only. All the data given are results on S.A.E. 1040 analysis of fully killed steel direct-poured in hot-topped molds giving 20-in. square ingots. Thus the variables of analysis and ingot size and contour are eliminated. Segregation results are all on the rolled-bloom size, not on the ingot itself. They are results from plant-control work and not results of special research on ingot segregation.

Jan 1, 1937

By D. Kuhlmann-Wilsdorf

A new theory of work hardening is developed which rests on only a few simple principles and is applicable to a wide variety of materials and dislocation structures. It explains, qualitatively, the general characteristics of the three-stage shear stress-shear strain curve of fcc metals, as well as the most important features connected with easy glide. The value of, the work-hardening coefficient in stage 11, is derived quantitatively, from first principles, and is shown to be insensitive to many changes in detailed dislocation behavior. The low rate at which energy is stored during mechanical working in stage 11, the dependence of slip line length on stress, and the so-called Cottrell-Stokes law are explained. Although the theory is primarily developed for fcc metals and alloys, it is largely applicable also to some other materiuls, and in particular apparently to poly crystalline simple steels in theh linear range of hardening. FOR pure fcc metals and alloys, after many different pretreatments and under a great variety of testing conditions, the well-known three-stage work-hardening curve is commonly observed. Moreover, the work-hardening coefficient in stage 11, 011, bears an almost constant relationship to G, the modulus of rigidity, such that K = G/Brr" = 300, within a factor of about 2 either way. The very fact that the three-stage curve and the value of K are so very persistent, can hardly be understood except on the assumption that some quite simple phenomena are responsible. In this light all available theories of work hardening must be judged unsatisfactory: Each of them is based on some quite specific dislocation model, while it is known that metals with similar values of K may have widely different dislocation structures, for example, dislocation tangles in the case of pure fcc metals, and piled-up groups of dislocations in a-brasstype alloys. Thus, while a particular theory might conceivably represent a special case with a reasonable degree of accuracy, it cannot possibly have illuminated the underlying principle. Another severe criticism applying to the presently most widely discussed theories is that they employ empirical or even quite unexplained parameters in order to arrive at a numerical value of K. This indicates that some vital aspect of the work-hardening process has remained unexplained. In the present paper, a new theory of work-hardening is developed which does not suffer from the above shortcomings. It is derived from first principles, and is founded on the realization that the underlying causes for the three-stage work-harden- ing curve and for the persistence of the numerical value of O,, must be few and simple. As a first step it is shown herein that the experimental oklservations on "easy glide" can be explained on the assumption that in this stage dislocations multiply, beginning in a number of restricted area:;, and from there penetrate into crystal regions still substantially free of glide dislocations until a quasi-uniform dislocation distribution has been established. During "easy glide", the resistance to the movement of the foremost dislocations, advancing into still largely a dislocation-free regions, is believed to control the flow stress. This resistance is determined by various factors, among them the reaction of the dislocations against bowing-out into loops, which is due to their line tension. Without such bowing-out no dislocation multiplication would occur, but the corresponding contribution to the flow stress stays practically constant all through stage I. According to the present theory, stage TI begins as soon as there are no more areas left into which newly formed dislocations have not yet penetrated, i.e., as soon :is a quasi-uniform dislocation density has been attaned. Regardless of how, in detail, the dislocations should happen to be arranged at the end of "easy glide", whether in pileups or tangles, on one glide system or on several, the stress necessary to overcome the line tension of the segments must now increase, because the dislocation density increiises while the average free dislocation length decreases. It is argued that all other contributions to the flow stress stay at about the same level as in stage I, and that the said increase in the stress necessary to bow out dislocation segments into loops is responsible for the major part of work hardening in stage 11. Stage TII of the stress-strain curve is explained by largely follouing the ideas of Seeger and his co-workers; however, it is pointed out that the start of stage m may on occasion indicate the onset of "conservative climb" instead of cross slip. Indirect evidence indicates that linear work hardening persists even under the profuse action of cross slip, but at a lower rate. Only when, in addition to cross slip, climb operates extensively, does the work-hardening rat,. drop sharply, ultimately down to zero. BRIEF SURVEY OF EXPERIMENTAL EVIDENCE The stress-strain curve of crystals of many different substances are qualitatively similar. No significant permanent plastic deformation takes place below the so-called "critical resolved shear stress". As the applied stress is raised beyond this level. yielding occurs with little or no work hardening and

Jan 1, 1962

By J. W. Pugh, J. D. Nisbet

THIS study of the ternary has been made as one phase of a metallurgical investigation which began nearly four years ago in the General Electric Company's Research Laboratory in Schenectady, N. Y. The objective of this program is the discovery of new metallurgical information which will lead to the development of better high-temperature materials. Combinations of the four pure base elements—iron, chromium, nickel, and cobalt—are being studied at the present time. It is essential in an investigation such as this to know as much as possible about the constitutional diagrams involved. The study of the iron-chromium-nickel system has been made to this end. Preliminary Explanation of Experimental Procedure: In all, fifty-five alloys at steps of 10 at. pct were made for the investigation of this ternary. Several ternary alloys in the chromium rich corner had to be omitted because their extreme brittleness made testing impractical. All alloys were vacuum melted with hydrogen reduction and centrifugally cast. The apparatus and technique of this process has been described in detail by Nisbet.1,2 The purity of the alloys prepared in this way is considered to be quite good. Impurities are listed as follows: Pct Carbon.............................0.02 Oxygen................................0.02 Nitrogen.........................0.005 Magnesium..................0.03-0.05 Sulphur...........................trace Hydrogen....................trace Phosphorous..................trace Silicon........................ trace After casting, all samples were given a homo-genization treatment which consisted of holding them for 15 hr at 1150°C (2100°F) and water quenching. Testing was begun with the samples in this condition. The tests employed in the study of this system were (1) dilatometer, (2) hardness versus aging temperature, (3) tensile strength and elongation versus temperature, (4) microstructure analysis, and (5) electrical resistance versus temperature. Dilatometer tests were made at the rather rapid heating rate of 1093°C (2000°F) in one hour on a Bristol-Rockwell type instrument. Hardness data were taken on specimens cooled from 204", 427", 649°, 760°, 871°, 982°, and 1093°C under conditions which are thought sufficient to bring the specimens to equilibrium in all but the cases of the very sluggish transformations. Electrical resistance data for several specimens were taken for both heating and cooling conditions in a vacuum furnace especially designed for this work by D. W. Bainbridge, formerly of this laboratory. Provisions were made for heating and cooling standard specimens at a constant rate, while autographic records of resistance and temperature were made simultaneously. Micrographs of all the alloys were made in the quenched condition. Some question may exist as to how such physical values as hardness, tensile strength, and elongation were interpreted to indicate a change in phase. Original data were recorded on physical property versus temperature graphs, each of which was made from the data of a single alloy (fig. la). From these, another series of graphs were plotted with the physical property as a function of composition for constant temperatures (fig. 1b). Sharp deviations in the slope of these composition versus hardness curves often indicate a change in phase. The example of fig. 1 will serve to describe this experimental technique. The plotting of a single point from graph "a" to graph "b," and finally to the phase diagram "c," is illustrated. The location of the point on graph "b" is indicated as point (1). If all the alloys of the A-B binary system were solid solutions at temperature X, the hardness in this curve would be expected to rise at a fairly even rate as A is diluted with B to a maximum at some intermediate value between A and B, as

Jan 1, 1951

By N. H. Emmons

An interesting development of copper blast-furnace construction has been brought about in adapting the blast-furnace to be a "burner" for sulphuric acid making. When the Tennessee Copper Co. first decided to construct an acid-plant, the standard type of brick-top furnace, supported by structural steel, was the only one in use at its plant. All the tests for temperature and strength of gas had been made on these furnaces, and had been satisfactory. When, however, the acid-plant was put on the flue, and the flue had to have a damper put in it to force the gas into that plant, troubles began. The furnaces were fairly tight, and for a few months the work was quite satisfactory. Fig. 1 shows the old type of furnace-top used at the start. It was soon found that this top would not stand the temperatures, particularly when dampered back, as was necessary to force the gas into the Glover towers. The structural steel, of which the furnace skeleton was constructed, warped and twisted so badly that it was not safe to use the furnaccs. This effect is shown by Fig. 2, which is a photograph of old No. 4 furnace, after the brick-work had been removed. It became apparent that a new type of top mas necessary and the engineering force was started on the design of a new furnace-top, with the result that a low top, with brick-lined flues at each end below the feed-floor, leading to the main concrete dust-chamber, was constructed. This furnace, No. 7, is shown in Fig. 3. The charging-doors are made of cast-iron sections, three sections to a door, and three doors to a side. A door to the furnace was made of east copper, but the heat was great that the copper bent readily, due to the jarring of its

Jan 1, 1911

By E. Orowan

LONG before the role of dislocations in the plastic deformation of crystals was recognized, the stress-strain field around dislocations received considerable attention in the theory of elasticity. It seems that Weingarten1 was the first to consider dislocations as simple and typical sources of internal stress in elastic solids, and Volterra2 and Timpe3 investigated their elastic field. Fig 3-1 shows the two basic types of dislocations considered by Volterra. The first arises by making a straight-edged .plane cut in a solid, displacing the two surfaces of the cut in their own plane relatively to one another by a constant amount in a direction perpendicular to the edge, and welding them together; this is shown in Fig 3-la, where the outer cylindrical surface represents the boundary of the solid, and the thin spiral cylinder around the edge of the cut has been removed in order to avoid infinities of stress and strain. The second type of dislocation is shown in Fig 3-lb; here the surfaces of the cut have been displaced relatively to one another by a constant amount parallel to the edge, and then welded together. After J. M. Burgers,4 these two types are called edge and screw dislocations, respectively. They represent simple limiting cases; in the general case, the surfaces of the cut are displaced by a constant vector that lies in the plane of the surface but has components both parallel and perpendicular to the edge of the cut. This vector is the Burgers or slip vector. The name “dislocation” was given by A. E. H. Love;5 it was bor-

Jan 1, 1954

By T. L. Joseph

The extent to which hot metal from the blast furnace affects open-hearth practice and the quality of steel produced has been discussed widely. Open-hearth operators have attributed difficulties experienced in making satisfactory steel to characteristics of the pig iron not disclosed by ordinary analysis. The commonest criticism of the iron has been that it is "physically cold" or "dirty." Often when the blast furnaces are working irregularly the quality of the iron is questioned. A cold hearth, slipping and hanging, the use in the past of unsintered flue dust, and the use of ores difficult to smelt have been associated with the production of iron of poor quality. The difficulty of the situation is that we have no proven yardstick for quality aside from ordinary analysis. Uniformity in analysis is recognized as being important, but the difficulty of changing the open-hearth practice when the iron analysis varies widely may not always be fully appreciated. Although the problem of correlating the characteristics of steel with those of pig iron is admittedly obscure, the effort of producers of quality steel to investigate all factors that may have a bearing on the final product is justified. This report contains data on the oxides in several hundred casts of basic iron produced in a furnace during the course of normal operation on Lake ores. Incidental to the study of the oxides in the iron, it was desirable to follow closely the temperature of the iron. The effect of temperature of the iron upon the silicon and sulphur present is discussed. A general relation between the basicity of the slag and the sulphur in the metal was developed. The amount and composition of oxides in the hot metal and in the steel bath during various intervals between melt-down and tap are discussed. Heats of rimmed steel, killed steel, and semikilled steel were investigated. The hot metal on individual heats was either all taken from a mixer or consisted partly of direct metal and partly of metal from the mixer. Samples of the iron for oxide determinations were

Jan 1, 1937

By Neville J. Price

In order that the reader may not be misled, I feel it necessary to comment upon the title of this paper. "Laws of Rock Behavior," one may take as being part of the all-embracing "Law of Nature" and this, according to the Oxford Dictionary, relates to the principles of conduct recognized as being pleasing to God. I feel it would be presumptuous to erect a code of rock behavior on this basis, so turn to a secondary definition, namely that a "Law" is that which is intrinsically reasonable. It is extremely unlikely that any group of geologists, or workers in rock mechanics would be in complete agreement about what could be taken to be "intrinsically reasonable." Therefore, this paper does not present any deified utterances, but rather deals with a few aspects of rock behavior which I consider to be intrinsically reasonable and with which I hope the reader will concur. The mode of behavior of rocks in the Earth's crust covers the range from wholly brittle to completely ductile ; with a deformation time scale which may be measured in milliseconds, for some events such as meteoritic impact, or in millions of years for the tectonic deformation involved in mountain building. A complete survey is, of course, outside the scope of an introductory paper, so I must be both brief and selective in my treatment. Any attempt to establish the mode of rock behavior in the Earth's crust should take into account data and relationships established in laboratory experiments and correlate these with field evidence. Consequently, the first section of this paper presents a brief discussion of the experimental aspects of rock mechanics which are pertinent to the subsequent discussion.

Jan 1, 1970

By Paul M. Tyler

THE farmer pays the phosphate miner! Phosphorus is used in fireworks; goes to battle in military smoke screens, incendiary shells, and tracer bullets; and, in vermin destroying pastes, does its part in the war against insects. A lemon phosphate can be had for a nickel at most soda fountains, and tens of thousands of tons of phosphate rock are mined annually for use in the food industries, chiefly for making monocaleium phosphate baking powder. Sodium phosphate cleaning, washing, and scouring compounds consume substantial quantities: the iron and steel industries buy a few thousand tons yearly to make ferrophosphorus and to balance foundry-iron furnace charges; and even nonferrous metallurgists use a little for phosphor bronze and other alloys. Phosphoric acid, its salts, and diverse other derivatives of this versatile element have countless applications, and industrial outlets are increasing rapidly, especially in the United States. Nevertheless, in this country nearly 90 per cent and in the whole world fully 95 per cent of the phosphate rock consumed is absorbed ultimately in agriculture.

Jan 1, 1938

By T. B. Counselman

"C" VERYONE who has to calculate cyanide circuits, -¦-' using either thickeners, filters or both, realizes the headaches involved in solving a set of simultaneous equations. When you calculate a large number of these, based on experimental data, trying to arrive at the best flowsheet, you can spend days at the task. T. B. COUNSELMAN, Member AIME, is Manager, FluoSolids Division, The Dorr CO., Stamford, Conn. AIME New York Meeting, Feb. 1950. TP 2783 B. Discussion (2 copies) may be sent to Transactions AIME before March 31, 1950. Manuscript received Aug. 23, 1949. Herewith is presented a short method, equally accurate with the standard simultaneous equation method, and much quicker. Here for instance is the standard simultaneous equation method, for 100 tons per day of $10 ore, with the conditions assumed as below (fig. 1). Conditions Assumed a. 100 tons of ore per day crushed in cyanide solution. b. Discharge from all thickeners with 50 pct moisture. c. $10 value dissolved per ton of ore. d. 50 pct in mill and 50 pct in agitators. e. 400 tons of solution from thickener V precipitated to $0.02. f. Agitation with a dilution of 2 of solution to 1 of solids. g. Let V, W, X, Y and Z represent value in dollars per ton of solution discharged from the resvective thickeners. Equating Out of and Into Each Thickener 1. lOOVplus 400V = 500W plus (0.50 X $10 X 100) 2. 1OOWplus 600W= 500X plus lOOW plus (0.50 X $10 X 100) plus lOOV 3. lOOXplus 500X = 1OOWplus 500Y 4. 1OOY plus 500Y = 1002 plus 1OOX plus (400 X 0.02) 5. 100 Zplus l00Z = l00Y plus 100 tons of water (value $0.00) Simplifying: 1. v = W plus 1.00 2. W = X plus 1.20 3. X = Y plus 0.24 4. Y = 0.2Zvlus 0.064 5. 2Z= Y

Jan 1, 1951

By T. B. Counselman

"C" VERYONE who has to calculate cyanide circuits, -¦-' using either thickeners, filters or both, realizes the headaches involved in solving a set of simultaneous equations. When you calculate a large number of these, based on experimental data, trying to arrive at the best flowsheet, you can spend days at the task. T. B. COUNSELMAN, Member AIME, is Manager, FluoSolids Division, The Dorr CO., Stamford, Conn. AIME New York Meeting, Feb. 1950. TP 2783 B. Discussion (2 copies) may be sent to Transactions AIME before March 31, 1950. Manuscript received Aug. 23, 1949. Herewith is presented a short method, equally accurate with the standard simultaneous equation method, and much quicker. Here for instance is the standard simultaneous equation method, for 100 tons per day of $10 ore, with the conditions assumed as below (fig. 1). Conditions Assumed a. 100 tons of ore per day crushed in cyanide solution. b. Discharge from all thickeners with 50 pct moisture. c. $10 value dissolved per ton of ore. d. 50 pct in mill and 50 pct in agitators. e. 400 tons of solution from thickener V precipitated to $0.02. f. Agitation with a dilution of 2 of solution to 1 of solids. g. Let V, W, X, Y and Z represent value in dollars per ton of solution discharged from the resvective thickeners. Equating Out of and Into Each Thickener 1. lOOVplus 400V = 500W plus (0.50 X $10 X 100) 2. 1OOWplus 600W= 500X plus lOOW plus (0.50 X $10 X 100) plus lOOV 3. lOOXplus 500X = 1OOWplus 500Y 4. 1OOY plus 500Y = 1002 plus 1OOX plus (400 X 0.02) 5. 100 Zplus l00Z = l00Y plus 100 tons of water (value $0.00) Simplifying: 1. v = W plus 1.00 2. W = X plus 1.20 3. X = Y plus 0.24 4. Y = 0.2Zvlus 0.064 5. 2Z= Y

Jan 1, 1951

By S. Frederick Ravitz

JUDGING from the inquiries that are constantly being received by the Utah Engineering Experiment Station as to the "Why," so to speak, of the flotation process of concentrating minerals, it occurred to me that perhaps a brief statement of the more important theories might interest those who have not followed the technical literature. Like many other industrial processes, flotation has hitherto been developed on an almost purely empirical basis, with relatively little practical contribution from the fundamental chemistry and physics on which the phenomena are based. In fact, its development by the trial - and - error method has been perfected to such a high state that it is becoming generally thought that further important advances can be brought about only by a thorough understanding of the actual mechanism of the process. Natur¬ally, such a complicated process has brought forth numerous theories, most of which have failed to withstand the test of time. It is significant that no theory has yet been advanced which is universally accepted.

Jan 1, 1933

By W. S. Tower

STEEL is the basic metal, the main metallic prop of the modern industrial world, a good gage for measuring the state of our complex economy. Any who had doubts on that score should have had them dispelled by the many evidences of public concern over the affairs of the steel industry in recent months. I do not need to relate the various criticisms of the industry, nor the questions about its policies and performance which have come in a rising flood, especially from unthinking and irresponsible sources. But judged from the standpoint of production, or from plans to improve and expand facilities, or from technical progress, the facts about the steel industry are proof of

Jan 1, 1948

By Edward Jeffrey

THE use of coke in metallurgy, to any important degree, dates from the middle of the 18th century. Its utilization came most opportunely for European civilization. The forests of Europe, except in the most remote and inaccessible regions, had been largely fed, in the form of charcoal, into the smelting furnaces. For a hundred years-the middle of the 17th to the middle of the 18th century-there was a stationary condition of population corresponding to the exhaustion of European forests. This situation, which was particularly evident in Great Britain, was due to the fact that the forests had been depleted and the practical utilization of coke had not begun. The coking industry is essential for our metallurgical industries, which in turn are basal to healthy economic progress. But coke is of great importance, not only on its own account, but for its byproducts, which enter fundamentally into all the arts of peace and war. The dyestuff industry and the manufacture of explosives are intimately connected with one another, as was shown by the recent war. The subject of coking coal, therefore, is well worthy the serious attention both of practical industry and the scientific investigator. The most valuable coking coals, from the metallurgical standpoint, are derived from the coals of highest ranks. Coals, for example, that have a carbon ratio of from 70 to 80 per cent. yield the most valuable coke for the blast furnace. The difficulty of investigating these coals, however, is great, for they are rather friable and delicate and possess a high carbon content, which makes them difficult to manipulate. They present, on account of their high carbon content, a considerable degree of opacity when examined, in thin sections, under the microscope. The tenderness of structure and blackness of such high-grade coking coals as those of Connellsville and the Pocahontas region make them extremely difficult to investigate.

Jan 1, 1925

By HUGH E. McKinstry

OPENING the sessions of the Mining Geology Committee, the program on postwar mineral controls drew a larger attendance than any other session of the entire meeting. In view of its general interest, the papers of this session, or a substantial portion of them, are printed elsewhere in this issue. Whether control of mineral resources can help to promote peace, how controls could be applied and to whom, are questions so far-reaching that naturally no pat answer was agreed upon. In fact the discussion took on something of the flavor of a debate between those who favor strict control and those who felt that attempting to ration nations in peacetime would defeat its own ends. Discussion from the floor emphasized the difficulties in administering any international control and the $64 question, that no one cared to answer, asked by a courageous young lady who was induced to mount the rostrum for the purpose, was whether the United Nations should exchange mineral controllers to police each other.

Jan 1, 1944

By AIME AIME

ON Tuesday afternoon, Feb. 17, a large and interested audience gathered in the auditorium of the Engineering Societies building to take part in the gold supply symposium that had been arranged for by the Mining Geology Committee. Waldemar Lindgren presided over the gathering and after brief introductory remarks on the international situation as regards lead, silver and gold, called on John Wellington Finch to present an oral abstract of the paper, "Sources and Trends in Gold Production," by R. J. Grant, director of the Mint, and. J. B. Knaebel. This ' paper reviewed the gold production of the world, by countries, since 1845, from the statistical viewpoint, leaving to the later speakers discussion of the statistics.

Jan 1, 1931

By Ernest Burchard

A RECONAISSANCE of the chrome and manganese'1ore deposits of Culm was made in the spring of 191s by Albert Burch representative of the U. S. Bureau of Mines and the writer representing the U. S. Geological Survey. The object of the study was to obtain authentic information for use of the: United States Government as to the location, character, size, and availability of the Cuban deposits of the ores of these important steel-alloy metals. The Cuban Government courteously detailed Sr. E. I. Montoulieu, a mining engineer connected with the Treasury Department, to act as escort and associate throughout the work on the Island. Mr. George A. Wright, of Baracoa, Cuba, a mining engineer especially familiar with the chromite deposits of Oriente Province, was a member of the party from Feb. 25 to Mar. 20. It was possible to visit most of, the chrome-ore deposits that seemed to be of promise, but there was not sufficient time to visit all that were brought to our attention, some of which may have merit. Furthermore, no attempt was made to examine the extensive chromiferous iron-ore deposits of the Mayari, Moa, and Cubitas districts, as these deposits cannot be regarded as sources of chromium except indirectly. At the close of the field work the essential data concerning the quantity and quality of ore probably available for shipment during 1918 and 1919, in the event of the continuation of the European war, and of the tonnage of ore in reserve, were furnished to such Government bureaus as were interested, including the Shipping Board and the War Industries Board, and as soon as chemical analyses of the chrome ores could .be obtained, a press bulletin on the subject was published by the Geological Survey. In the present paper the engineering data, and tonnage estimates contained in the unpublished notes of Mr. Burch have been freely used, and their helpfulness is hereby gratefully acknowledged. Many thanks are due Senor Montoulieu and Mr. Wright for their valuable work in the field; to the officials of the Spanish American Iron Co. and of the various other companies; and to individuals holding chromite claims, for courteously facilitating the work of the party. In the study of material for the present paper, chemical analyses have been made by R. C. Wells and petrographic determinations and descriptions were furnished by Miss E. F. Bliss, both of the U. S. Geological Survey.

Jan 9, 1919

The National Mine Health and Safety Academy near Beckley, W. Va., is dedicated to reducing accidents and improving health conditions in the mining industry through education and training. Though this basic mission remains unchanged, the Academy now serves a much broader mining community than it did when established in the late 1960s. From its original emphasis on training federal coal, metal, and nonmetal mine safety inspectors, the Academy has expanded its programs to reach mining industry and labor representatives, state agency employees, and university students taking mining-related courses. The Academy's resident programs, short courses, seminars, and continuing education courses cover a wide range of subjects and various experience levels, but all have been developed with one idea in mind - to reduce accidents and health hazards through education and training of the widest possible audience.

Jan 11, 1979