Search Documents

By John Griffen

This paper records over twenty years' experience with the use of the Rheolaveur system in the United States, showing its ability to meet changing conditions caused by the dirtier mine output of present-day mechanical mining methods. Data are given on size ranges handled, number and capacity of units installed, maintenance experience, and operating results on two-product and three-product separations. IT is not the purpose of this paper to discuss the principles employed in the Rheolaveur system of fine-coal cleaning as these have been fully covered in the technical literature of the Institute."2 Rather, our purpose will be to record the highlights of over 20 years' experience in the United States with Rheolaveur fine-coal launders, which will indicate their capabilities and costs of cleaning and their adaptability to meet the changing conditions caused by present-day mechanical mining methods. Rheolaveur fine-coal launders are used in the United States to treat a wide variety of size ranges of fine coal, the coarsest being 1/2 in. to 0 and the finest about 1/8 in. to 0. In Europe feeds as coarse as 5/8 in. and as small as 1/2 mm (28-mesh) to 0 are being cleaned. The size ranges usually handled in this country are 3/8 to 1/4-in. round to 0. Thirty five units with a combined hourly feed capacity of 3200 tph have been installed in the United States. Individual units are cleaning as little as 25 tph, while others are cleaning as much as 200 tph. Rheolaveur fine-coal launders offer cleaning units of high capacity and are outstanding in requiring a minimum of building space per ton of input. Experience has shown that maintenance costs are low. Several installations were made in the Pittsburgh district from 1928 to 1930, and since that time operation has been largely two shifts per day. Minor repairs to liner plates and Rheo boxes have been required during the intervening years, but no major replacement of launders was required until 1947 and 1948. At one of these plants, launders operated for 17 years before they were replaced and during that period over 26,000,000 tons of —5/16-in. coal were cleaned. The effect of the much dirtier raw coal produced by mechanical loading of the Pittsburgh seam is shown by the following tests. The data in table I summarize the performance of a Rheo fine-coal unit when cleaning hand-loaded raw coal. The —4-in. raw coal fed to the cleaning plant analyzed only 8.16 pct ash and 1.31 pct sulphur and contained 4.6 pct sink, 1.55 sp gr. Two years later, in 1945, mechanically-loaded coal from the same mine was cleaned in the same plant. The feed, —4 in., then analyzed 20.10 pct ash and 1.53 pct sulphur and contained 20.2 pct sink, 1.55 sp gr. The performance of the Rheo fine-coal unit when cleaning this coal is given in table 11. It will be noted that the +48-mesh coal is cleaned almost as thoroughly as in table I. The large amount of high-ash slimes produced from the dirtier feed are responsible for the higher ash of —--48-mesh washed coal in table 11. In this plant the Rheo fine-coal unit did not get the full load of refuse resulting from mechanical

Jan 1, 1951

By John Griffen

This paper records over twenty years' experience with the use of the Rheolaveur system in the United States, showing its ability to meet changing conditions caused by the dirtier mine output of present-day mechanical mining methods. Data are given on size ranges handled, number and capacity of units installed, maintenance experience, and operating results on two-product and three-product separations. IT is not the purpose of this paper to discuss the principles employed in the Rheolaveur system of fine-coal cleaning as these have been fully covered in the technical literature of the Institute."2 Rather, our purpose will be to record the highlights of over 20 years' experience in the United States with Rheolaveur fine-coal launders, which will indicate their capabilities and costs of cleaning and their adaptability to meet the changing conditions caused by present-day mechanical mining methods. Rheolaveur fine-coal launders are used in the United States to treat a wide variety of size ranges of fine coal, the coarsest being 1/2 in. to 0 and the finest about 1/8 in. to 0. In Europe feeds as coarse as 5/8 in. and as small as 1/2 mm (28-mesh) to 0 are being cleaned. The size ranges usually handled in this country are 3/8 to 1/4-in. round to 0. Thirty five units with a combined hourly feed capacity of 3200 tph have been installed in the United States. Individual units are cleaning as little as 25 tph, while others are cleaning as much as 200 tph. Rheolaveur fine-coal launders offer cleaning units of high capacity and are outstanding in requiring a minimum of building space per ton of input. Experience has shown that maintenance costs are low. Several installations were made in the Pittsburgh district from 1928 to 1930, and since that time operation has been largely two shifts per day. Minor repairs to liner plates and Rheo boxes have been required during the intervening years, but no major replacement of launders was required until 1947 and 1948. At one of these plants, launders operated for 17 years before they were replaced and during that period over 26,000,000 tons of —5/16-in. coal were cleaned. The effect of the much dirtier raw coal produced by mechanical loading of the Pittsburgh seam is shown by the following tests. The data in table I summarize the performance of a Rheo fine-coal unit when cleaning hand-loaded raw coal. The —4-in. raw coal fed to the cleaning plant analyzed only 8.16 pct ash and 1.31 pct sulphur and contained 4.6 pct sink, 1.55 sp gr. Two years later, in 1945, mechanically-loaded coal from the same mine was cleaned in the same plant. The feed, —4 in., then analyzed 20.10 pct ash and 1.53 pct sulphur and contained 20.2 pct sink, 1.55 sp gr. The performance of the Rheo fine-coal unit when cleaning this coal is given in table 11. It will be noted that the +48-mesh coal is cleaned almost as thoroughly as in table I. The large amount of high-ash slimes produced from the dirtier feed are responsible for the higher ash of —--48-mesh washed coal in table 11. In this plant the Rheo fine-coal unit did not get the full load of refuse resulting from mechanical

Jan 1, 1951

By Paul L. Russell

THIS is a progress report of an experiment being undertaken in cooperation with the Bethlehem Steel Corp., the Crucible Steel Co., and the Rock Bit Sales and Service Co., involving heat treatment of the shank ends of drill steel. This experiment is being conducted by the U. S. Bureau of Mines in its experimental mine, Mining Research Branch, Bluemont, Va. The purpose of the experiment is to determine the effect of an increase in the time the steel soaks in the furnace during the hardening heat. It has been thought that increasing this time produces a soft zone below the lugs resulting in a metallurgical notch that causes early failure. Each of the steel companies furnished enough 11/4 - in. straight carbon, hollow, round steel to make up 10 sets of drill steel, in each instance the steel bars were from the same heat. These sets of drill steel, consisting of 2-ft, 4-ft, 6-ft, and 8-ft lengths were fabricated by the Rock Bit Sales and Service Co. Special attention was given to the forging of the steel to produce the best rods possible. The heat treatment of all thread ends was identical and followed the best practice. The heat treatment of the shank ends of five sets of steel from each company produced a soft zone 2 to 4 in. in front of the lugs. It was decided that possibly the best way to obtain this effect was not to overlap the hardening heat but to let the steel soak for an additional 30 min before quenching. Therefore the only variable in the test steels is the length of time the shank ends were in the furnace. The remaining drill steel shanks were treated as follows: Heat treatment in pyrometer-controlled furnace at 1550°F. Quenching oil at 105°F to 125°F temperature. Areas for heat treatment were; shanks, 11 in.; threads, 9 in. Time at heat, standard practice, 20 min for 11/4-in. steel. Actual drilling tests were made in greenstone, (a metamorphosed basaltic rock), and in epidosite. Greenstone has a specific gravity of 2.96 and a compressive strength of 44,200 psi. Epidosite has a specific gravity of 3.26 and a compressive strength of 63,100 psi. All drilling tests were made using a 31/2-in. column-mounted, automatic feed drifter, with a controlled air pressure of 90 psi at the throttle. Tungsten-carbide bits of 2 in. diameter were used for all drilling. Contrary to expectations the drill steels that were allowed to soak for the additional 30 min before quenching performed better than the steels that were heat treated according to standard practice. This performance, as shown in Table I, was especially noticeable in the drilling of epidosite. The "longheat" drill steels furnished by Company "A" drilled 154 pct more minutes than the "standard-heat" steel. Expressed in feet, the "long-heat" steel drilled 114.60 ft more before failure than the "standard-heat" steel. The "long-heat" steel furnished by Company "B" drilled 37 pet more minutes or 60.39 ft more before failure than the "standard-heat" drill steel. The effect of the long heat treatment was not as evident when the steels were drilling in greenstone (Table II). In greenstone, the increase in minutes drilled by the "long-heat" steel over the "standard-heat" steel was 47 pet and 1 pet, respectively, for Companies "A" and "B."

Jan 1, 1952

By Chas Dobbel

THE Chief Consolidated properties are situated in the Tintic mining district of Utah, being included in Juab and Utah Counties, about 70 miles south of Salt Lake City. The drilling referred to in this paper has been carried on in the Chief Consolidated No. 1 mine, the Gemini mine, and the Eureka Hill mine at Eureka, the Grand Central mine, above Mammoth, and the Apex Standard mine just south of Dividend. The occurrence of ore through the district is typically in lenses on bedding or breaks, and in connecting pipes, without accurate geometrical trend so that the ratio between the total length of development in drifts and crosscuts to the square feet of ore exposed is very high. A section of one of the western channels (Fig. 1) through the Tintic district, shows, roughly, the irregularities calling for excessive development work, so typical of the Tintic mines. This irregular trend of the ore constantly calls for excessive cutting up of the whole area for offshoots and the connecting links always present.. In the planning of prospecting and development, no regular system may be laid out without overlooking some orebodies or segments of orebodies. It was with these facts in mind that Cecil Fitch, the general manager of the Chief Consolidated Mining Co., decided that some method of drilling was the more feasible way of successfully cutting up and bringing about the discovery of ore believed to exist; yet this drilling had to compete with a great. margin of cost over crosscutting, as a crosscut in the Tintic district, even though barren, brings out geologic facts that, in many cases, are worth the price of the working itself. Diamond drills met with the success that might be expected in a district that has a reputation for the wear and loss of diamonds; after 6 or 8 months, this method was discarded on account of the high costs. Simultaneously, a small churn drill outfit was set up underground but a few shifts proved its inapplicability. At the same time, the ordinary hammer drill was usd to drive prospect holes with jointed steel.

Jan 9, 1925

By David White

ATTENTION has been given to the sources and supply of the raw vegetal matter and. the conditions of its submission to the process of sedimentation. An original and most valuable review has been made of the more important or significant chemical compounds originally contained in the organic debris, and of the biochemical changes-undergone by the latter during deposition. Consideration also has been given to the factors controlling the selective biochemical decomposition, in whole or in part, of :this debris, and the deposition, as, sediments, of the undecomposed plant structures and compounds, together with more or less of the so-called "ulmic," or "humic," organic decomposition products in colloidal solution.1 BIOCHEMICAL CHANGES END IN PEAT FORMATION The biochemical process terminates in the peat stage of coal formation, and with the cessation of this process organic sedimentation is completed. All subsequent changes result from geological causes and conditions. The deposits are in the form of peats of different types, organic muds, oozes, etc. They are essentially uncompressed and are wholly unconsolidated, and their water content is great, amounting to over 85 per cent. near the surface of the deposit. Many of the chemical compounds remain as in the once living organisms; others are biochemically broken down and new ones formed.

Jan 2, 1925

By J. J. Jonas, G. Gagnon

SHG zinc was extruded in the temperature range 110" to 350°C and the strain rate range 0.05 to 5 sec-1 The strain rate/flow stress/temperature results were analyzed using a power sinh stress relationship. When temperature changes due to the heat of deformation and to heat losses are neglected, the exponent of the sinh function of the stress is 5.6, and the apparent activation energy of deformation is 28 kcal per mole. When these changes are taken into account, the exponent decreases to 4.7 and the activation energy to 23 + 2 kcal per mole. The corrected stress exponent and activation energy are in very good agreement with published values obtained from creep experiments, and suggest that the hot extrusion of zinc is controlled by a mechanism involving self-diffusion. When the extrusion and creep data are compared using a Zener-Hollomon parameter and either a sinh or an exponential stress term, an appreciable offset is observed, which may be due to the difference in impurity content. For a given set of extrusion conditions the ram speed, maximum pressure, and initial temperature can also be correlated using a Zener-Hollomon parameter and a sinh pressure term. THE deformation of metals at temperatures over about one-half the absolute melting temperature has been extensively studied at creep strain rates. By contrast, relatively little work has been carried out on the behavior of metals at hot working strain rates. Most of the latter investigations have been performed using simulative methods, such as hot torsion and hot compression, in which the friction conditions and temperature rise during deformation may differ appreciably from those existing under industrial conditions. Recently, however, Wong and Jonas1 used a scaled-down industrial process to determine the stress and temperature dependence of the strain rate during the extrusion of aluminum. In such tests, the effects of friction and adiabatic heating are closer to those produced in industrial operations. Also, with regard to the testing of materials of limited ductility such as zinc, hot compression and hot torsion do not permit the attainment of true strains as large as the deformations usually applied commercially. The present study was undertaken to investigate the extrusion behavior of Special High Grade (SHG) zinc. The detailed objectives were: 1) to establish the stress and temperature dependence of the strain rate with and without a consideration of adiabatic heating, 2) to study the pressure and temperature dependence of the ram speed, and 3) to investigate the microstruc- tural changes occurring during the deformation. The last aspect of the investigation will be covered in a separate paper. The treatment described below differs from that of Wong and Jonas in that the adiabatic temperature rise during deformation is taken into account, and the calculation of the mean equivalent strain rate is based on the redundant as well as on the homogeneous work. EXPERIMENTAL PROCEDURE Rods from two shipments of continuously cast SHG zinc* were used in the investigation. The composition *Supplied by courtesy of Cominco Ltd. range of the impurities present, as given by the supplier, was: Pb: 0.0013 to 0.0023 pct, Fe: 0.001 pct max Cd: 0.0001 to 0.0006 pct, Cu: 0.0002 to 0.0005 pct, Ti: 0.0001 pct max; thus, by balance, zinc valued from 99.9963 to 99.9966 pct. The as-received rods were machined into billets having a nominal diameter of 1.56 in. and a nominal length of 1½ in.; longer billets up to 4 in. in length, were also used to investigate special aspects. The as-machined rods were annealed at 400°C for 24 hr and slowly cooled. This treatment produced a columnar grain structure, with a grain size of about $ by 2½ cm which was appreciably larger than the as-cast one. A 150-ton, direct extrusion, vertical press was used. Ram displacement and force were recorded continuously against time. A constant flow control valve permitted the maintenance of a range of preselected ram speeds up to in. per sec. The selected speed was held constant, irrespective of the required force, as long as the load developed was below the maximum available. Strain gages were used to determine the force; the gages were calibrated before and after each testing period with a 200,000-lb capacity load cell. Further details of the experimental equipment can be found in Ref. 2. The billets were preheated for 90 min in the extrusion container, which was well insulated so as to minimize temperature gradients. This period was sufficient for the billet to reach a uniform temperature at all temperatures between 110" and 350°C. A square-shoulder die having a 0.290-in. diam central hole was used. The extrusion ratio was 30 to 1. This is equivalent to a reduction in area of 96.7 pct, an elongation of 2900 pct, and a true strain of 3.4. The ram speed was varied over two orders of magnitude from 0.0027 to 0.26 in. per sec. The ram was water-cooled during most of the tests, although some experiments were conducted with a preheated, uncooled ram. All extrusions were run without lubricant, which resulted in conditions of sticking friction. EXPERIMENTAL RESULTS Stress Dependence of the Strain Rate Neglecting Adiabatic Heating. The maximum force required to extrude is given in Table 1 for each of the five initial

Jan 1, 1970

By C. A. Heiland

For a long time it has been known that it is possible to deduce conclusions about the physical constitution of the interior of the earth from the records of natural earthquakes obtained by stationary seismographs. In view of this fact it is surprising how late, relatively speaking, geologic prospecting by seismic methods has been taken up, although the first suggestion was made 40 years ago- that travel-time curves of artificial explosions might be used for the study of the change of the velocity of seismic waves as depth. Further suggestions of practical applications of artificial explosions for geologic purposes were made by Belar,2 by von dem Borne,3 by Benndorf4 and by Galitzin,5 but it was not until 1919 that Mintrop obtained. a patent on the seismic prospecting method which he has applied commercially on a large scale ever since. Dr. Mintrop came to this country with his method at about 1923. Since that time, several. American oil companies have developed seismographs of the mechanical type for the vertical component similar to that of Mintrop's (Humble Oil Co., Dr. Ricker). Other consulting geophysical companies designed other types of seismic devices, the simplest of them for the recording of the first impulse being the geophone (McCollum Geophone Co.). The galvanometric recording method as first proposed by Galitzin is being used (Geophysical Research Corpn.?) and use is being made even of the piezoelectric properties of crystals for portable seismographs (F. Rieber).. There is such an enormous variety of all kinds of portable seismographs, vibrographs, accelerographs, etc., that it is difficult to decide just what kind is preferable. Unfortunately, nothing has been published as yet about American designs of portable seismographs, except the Wood Anderson torsion-seismometer. After Mintrop's design of portable seismographs, other constructions were made.

Jan 1, 1928

By Louis G. Bailey

This paper .reviews some of the key developments which have been made in the synthesis of the III-V compound semiconductors and the associated progress in obtaining high-quality material for device development. The history of the investigation of the semi-conducting properties of these materials has indicated the need for synthesis techniques capable of producing rnaterial of high chemical purity and physical perfection. The progress in the area is described, and the present status of quality of several compounds is discussed. In addition, recent studies of localized epitaxial deposition of GaAs into semi-insulating GaAs substvates for the development of arrays of devices ave reviewed. In conclusion, some important areas for future research and developrnent are discussed. INTEREST in III-V compounds as semiconductors dates back to the period 1950 to 1952, when Goryunova, Ioffe, and, in particular, Welker determined that 111-V compounds were structural analogs of the group IV elements carbon, silicon, germanium, and tin and that they were also semiconductors.'-3 Since that time interest in the properties of these materials has ex- panded rapidly. During 1953 and 1954, the first reports of rectification, photoconductivity, and optical absorption in these materials came from several investigators. In 1955, recombination radiation from samples of GaAs, InP, and GaSb was reported by ~raunstein .' This radiation was produced by injected minority carriers from point and large-area contacts. From 1955 to 1960, efforts increased on preparing large, pure specimens of these materials for the study of basic physical phenomena and device exploration. By 1960, materials preparation and the understanding of the physics of some of the materials had advanced to where some very interesting and potentially useful phenomena came under study. The first observation of electric-field-induced changes in the optical absorption edge (Franz -Keldysh effect) of 111-V compounds was reported for GaAs by Moss in 1961.' In 1962 the study of recombination radiation advanced rapidly. Keyes and Quist6 and Pankove and Berkey-heiser7 reported high radiative efficientices obtained from recombination, and then the first injection electroluminescent lasers in GaAs were announced by Hall ef al.,' by Nathan et al.,O and by Quist ef al.,'O and in Ga(As, P) alloys by Holonyak and Bevacqua." Hil-sum has reviewed the early work leading to the first observations of laser action in GaAS." Recombination processes in GaAs, Gap, and the other 111-V com-

Jan 1, 1968

By F. E. Pawlek, J. K. Gerlach

The chloridizing roasting of ores is applied when metal sulfides and oxides are to be converted into soluble or volatile compounds. The chlorine required is either obtained from the admixed chlorides of sodium or calcium or added in the gaseous state. In the first part of the investigations the reaction rate of the chlorides of sodium or calcium with gas mixtures of SO,-0, or SO ,-O2 ,-SO , was measured. The rate for reactions with gas mixtures SO2-O2 is ThE chloridizing roasting of ores is applied when metal sulfides and oxides are to be converted into soluble or volatile compounds. At present the process is mainly applied to produce nonferrous metals which occur in pyrite cinders in small concentrations. Thereby the nonferrous metals are converted into water-soluble, acid-soluble, or volatile compounds whereas all the iron remains as insoluble oxide. The chlorine required is either obtained from the admixed chlorides of sodium or calcium or added in the gaseous state. The reactions occurring during the roasting process can be divided into two groups: solid-solid reaction and gas-solid reaction. The reactions between solids proceed by means of solid-state diffusion and are therefore of low velocity. The heterogeneous reactions between solids and gases of the roasting atmosphere5 are high-velocity processes and determine the velocity of the chloridizing roasting. These gas-solid reactions shall be the subject of the paper presented. In order to investigate the still little-known processes which occur during the chloridizing roasting 6-' the complex reaction is split into several partial steps. First the reactions of NaCl and CaCl, with gas mixtures of SO2 and 0, have been investigated at temperatures between 500" and 600°C by measuring the weight increase of the samples. The gas mixtures used in this series of experiments had first variable compositions, then the amount of SO 2 had been increased. Furthermore the influence of Fe 2 O3 admixtures upon these reactions, the behavior of pure Fe 2 O3 with the gaseous reactants, and the chlorination of the sulfides of lead, copper, nickel, and zinc have been investigated. FORMATION OF GASEOUS CHLORINE Pyrite cinders are never completely roasted and therefore contain still a small amount of sulfide sulfur. When heated again in air, this sulfur is converted into SO,. Accordingly the formation of chlorine can first be described by the reactions: dependent on the composition of the gas phase. If more than 1 pct SO 3 is added to the roasting gas, the reaction rate is determined only by the concentrations of the SO,. In the second part the reactions between chlorine and metal sulfides are discussed. The rate of formation of gaseous chlorine is higher by me order of magnitude than is the reaction rate between ZnS and chlorine. The reaction rate of NiS and PbS lies considerably below that of ZnS. The conversion rate of both pure Fe 2 O 3 and Fe 2 O 3 containing NaCl or CaCl2 when reacting with SO2-O2, mixtures with and without SO3 portions was measured at temperatures of 500", 550°, and 600°C. The weight increase of pressings was determined by means of a spiral balanceg and the reaction rate calculated therefrom according to Eqs. [ll to [31 and [5] to [7]. The prepared samples were suspended on a platinum filament in a vertically mounted tube of mullite (ID 4 cm, length 110 cm) which could be heated by a resistance tube furnace. The platinum filament was tied to the lower end of the spiral balance. A supremax glass tube (length 70 cm) was mounted gas-tight on top of the reaction tube. The unit was sealed up at its top by a ground-in stopper which was holding the spiral balance with the sample. The spiral balance therefore hung outside the high-temperature region of the furnace. Fig. 2 shows the experimental arrangement schematically. While lowering the sample into the reaction tube pure nitrogen was flowing through the reaction zone providing a protective atmosphere. After the sample had reached the reaction temperature within approximately 1 min, the protective gas was replaced by the sulfur dioxide-oxygen reaction mixture. It took about 30 sec until the mixture filled the tube homogeneously. A Ni/NiCr thermocouple placed in the center of the furnace where the sample hung during the measure-

Jan 1, 1968

By K. C. Ten Brink, Allen D. Garrison

A rrevious paper1 reviewed some of the properties of clays and shales and presented some data on the nature of the gelling phenomenon. It included a brief discussion of origin of clays and shales, their composition, structure, retention of water, ionization, base exchange, and the nature of the gelling of water suspensions. Other publications of the Institute2-8 have discussed the properties of clays and their relations to drilling-fluid behavior and control. It is the purpose of this article to present some new data obtained and arranged in a different manner and making possible a better understanding of the chemical reactions involved in the control of drilling-fluid characteristics during the normal drilling operations. Experimental Procedure The difficulties involved in the measurements of the flow characteristics of plastic fluids are too familiar to recite. The possible applications of some of the well-known instruments to this problem have been adequately discussed by Hobson9 and he has given an excellent bibliography. Although there are many viscosimeters of varied design, none of them appear to fulfill the most obvious demands of accuracy in the measurement of clay or shale suspensions. Since the fluid characteristics are dependent on the rate of flow of the fluid, and the viscosity usually falls off very rapidly as the rate is increased, it is clear that the first requirement is that the instrument shall be capable of a wide variety of speeds. The viscosity of the fluid at any fixed and constant rate of flow is also a function of time, so that the second demand is that the instrument shall be capable of a constant and continuous motion for a prolonged period of time.

Jan 1, 1940

By K. C. Ten Brink, Allen D. Garrison

A rrevious paper1 reviewed some of the properties of clays and shales and presented some data on the nature of the gelling phenomenon. It included a brief discussion of origin of clays and shales, their composition, structure, retention of water, ionization, base exchange, and the nature of the gelling of water suspensions. Other publications of the Institute2-8 have discussed the properties of clays and their relations to drilling-fluid behavior and control. It is the purpose of this article to present some new data obtained and arranged in a different manner and making possible a better understanding of the chemical reactions involved in the control of drilling-fluid characteristics during the normal drilling operations. Experimental Procedure The difficulties involved in the measurements of the flow characteristics of plastic fluids are too familiar to recite. The possible applications of some of the well-known instruments to this problem have been adequately discussed by Hobson9 and he has given an excellent bibliography. Although there are many viscosimeters of varied design, none of them appear to fulfill the most obvious demands of accuracy in the measurement of clay or shale suspensions. Since the fluid characteristics are dependent on the rate of flow of the fluid, and the viscosity usually falls off very rapidly as the rate is increased, it is clear that the first requirement is that the instrument shall be capable of a wide variety of speeds. The viscosity of the fluid at any fixed and constant rate of flow is also a function of time, so that the second demand is that the instrument shall be capable of a constant and continuous motion for a prolonged period of time.

Jan 1, 1940

By H. J. Wasson

WITH the close of 1932 and the third year of the depression, the activity of oil production presents, amidst the general wreckage and chaos of industrial society, a somewhat unique picture of rationalized economic effort. East Texas still dominates the contemporary horizon, but it has become, at least for the time being, a definitely known factor. With its 9500 wells it is approximately 90 per cent drilled up. So long as production control obtains, it is merely one important factor of the national oil reserve. Each succeeding month of stabilized production tends to lull the industry's fears and the menace, both actual and psychological, of this giant field becomes ever more remote.

Jan 1, 1933

By R. G. Bowman

Discussions of processes for the manufacture of white lead generally open with the statement that white lead is the oldest chemical pigment known to man. This fact is of more than historical interest; in the light of the present extensive use of white lead, it indicates that the compound possesses characteristics that make it unique among white pigments, and superior to all in its particular field. A greater variety of processes have been proposed for manufacturing white lend than for any other one chemical compound. Only a few of these processes have come into commercial use, however, and a large part of the present production here and abroad is made by the process used in ancient times. The outstanding disadvantages of the old process are that it is slow and laborious, affords no control of the product, and yields at best an impure material lacking in uniformity. Improved processes, sometimes classed all together as "quick processes," have had as their main object the shortening of the time required. Most of them accomplish this and some have yielded a superior product as well, but only two or three are now in use commercially. For centuries the manufacture and mixing of paints have been treated as an art, and the practice has been much influenced by tradition and precedent. There is a reluctance to abandon old materials for this purpose, and as few new uses for white lead have been developed, the adoption of the quick processes has been slow. The electrolytic production of white lead is not new, a large number of processes and forms of apparatus have been proposed and patented within the past 25 years, all directed toward the production of white lead, wholly or in part, by electrolysis. One or two of these processes were tried commercially but proved unsuccessful. Process The Sperry process, used by the Anaconda Lead Products Co., is the invention of Elmer A. Sperry, and was worked out to a commercial basis at the East Chicago plant. It resembles, in a general way, earlier methods, but embodies the features that make it possible to operate

Jan 1, 1926

By Hermann Wedding

It is now fourteen years since we German ironmasters, in considerable number, visited the United States on the occasion of the Philadelphia Exposition, and found the iron metallurgy of this country, as must be frankly confessed, in an advanced stage of development not previously suspected by us. At that time the United States already occupied, as now, the second rank, with Germany in the third, the product of pig-iron for that year being, in Great Britain, 6550, in this country, 2093, and in Germany, 1850 kilotons.* This relative position has not been changed. The present annual product of the three countries is, in round numbers, Great Britain, 8380, the United States, 7790, and Germany, 4530 kilotons. But the proportion of the United States, which was, in 1876, but 15 per cent. of the world's product, has now advanced to 30 per cent. When we left America in 1876, it was not only with gratitude for cordial hospitality and for the liberality with which our professional colleagues here had opened to our inspection whatever was worthy of notice in our special field, but also with the conviction that we had collected a great treasure of new and interesting information which we could utilize for the benefit of our German Fatherland. Particularly the achievements of the never-to-be-forgotten Holley in the field of Bessemer practice, set us an inspiring example for imitation in our own country. As an expression of our thanks in more practical fashion, I attempt in this paper to sketch what we have done in Germany since

Jan 1, 1891

By Donald A. Brobst

The minerals barite (BaSO4-barium sulfate) and witherite (BaCO3-barium carbonate) are the chief commercial sources of the element barium and its compounds whose many uses are nearly hidden among the technical complexities of modern industrial processes and products. Barite, the major ore mineral, is extremely vital to the petroleum industry which in 1980 consumed at least 90% of the world's production of 8.8 million tons as a major ingredient of the heavy fluid, called mud, that is circulated in rotary drilling of oil and gas wells. The remaining 10% of the barite production was consumed chiefly in the manufacture of barium chemicals and glass and as a pigment, filler, and extender. Barite occurs throughout much of the world and is available from three major geologic types of deposits-vein and cavity filling, residual, and bedded-in sufficient quantity at competitive prices to meet current demands. The world's demand for barite is expected to increase, and geologic circumstances are favorable for the discovery of new deposits of commercial value. Witherite is much less common and abundant than barite, although it is more desirable in many ways as a raw material for the production of barium chemicals. The United States has not produced witherite since about 1950; England is currently the chief producer of witherite. End Uses Most of the world's barite production since 1926 has been used as a weighting agent for the muds circulated in rotary drilling of oil and gas wells. The muds fundamentally are mixtures of water, clay, and barite in different proportions that vary according to local reservoir conditions. Muds with a specific gravity as great as 2.5 are used. The mud is pumped down the hollow drill stem, passes through the bit at the bottom of the hole, and rises to the surface in the space between the drill stem and the wall of the hole. In the course of this circulation the drill bit is cooled, cuttings are removed, the drill stem is lubricated, the walls of the hole are sealed, and the hydrostatic head of the column of weighted fluid helps to confine high oil and gas pressures. The latter feature aids in prevention of gushers, thus reducing both environmental pollution and waste of oil and gas resources as well as conserving the natural reservoir pressure for greater production and rate of recovery of the products contained in the rocks. Barite is particularly well suited for drilling mud because it is clean, easy to handle, soft (nonabrasive), heavy, virtually inert chemically, and relatively inexpensive compared to many other available heavy materials. Barite is used in the manufacture of glass in continuous tanks. The addition of barite homogenizes the melt and gives greater brilliance and clarity to the finished glass. Ground barite, both unbleached and bleached by sulfuric acid, is a common industrial filler, extender, and weighting agent. The rubber industry is a major consumer of barite as a filler. Barite also is added to bristolboard, heavy printing paper, playing cards, rope finishes, brake linings, clutch facings, plastics, and linoleum, to name but a few uses. Bleached barite has long been an extender in white lead paint because of its weight. The low index of refraction of barite, however, makes its ability to cover marks poorer than some other substances, but its low capacity for absorption of oil is a good feature. Off-color or unbleached barite can be used as a filler in colored paints. In the construction industry, some lump barite is used in concrete aggregate to weigh down pipelines buried in marshy areas and to shield nuclear reactors. Because barite absorbs gamma radiation well, its use reduces the amount of expensive lead shielding otherwise

Jan 1, 1983

By Michael Tenenbaum

THE importance of semikilled steel as a high tonnage grade has long been recognized. The increasing severity of the applications for which semikilled steel is used makes it desirable to obtain further information regarding the features of open hearth practice and ingot structure that can affect steel performance in subsequent rolling and fabricating operations. Accordingly, an investigation is being carried out studying the structure of various types of semikilled steel ingots. This paper reviews some of the observations made and information gathered in this investigation. By definition, semikilled steel may be considered to include all nonrimming steels in which the natural shrinkage occurring during ingot solidification is offset to an appreciable degree by gas formation. Accordingly, this type of steel includes the entire range intermediate between rimmed and fully killed steel. The resultant ingot structures range from those of steels that have been capped to suppress a weak rimming action to those steels that have been killed in the furnace or ladle to the extent that no mold deoxidizer is required. A survey reported to the 1946 AIME Open Hearth Conference' reviewed the practices being used at 28 major plants for the deoxidation of semikilled steel. It was found that most plants divide the deoxidizing additions between the ladle and the mold many of the plants adding only minor amounts of deoxidizer to the bath or none at all. Silicon, aluminum and titanium were the only elements used for ladle and mold deoxidation. Mold deoxidizers were added as capping additions or as uniformly fed additions. Several practices were reported in which the steel was deoxidized in the ladle to the extent that little or no mold deoxidation was needed. No reference was made to grades capped by using special mold designs or special closures over the top of molds. Accordingly, specific examples of this type of practice will not be considered in this paper. It appeared from this survey of deoxidation practice that semikilled steel can be divided into three types, namely, capped semikilled, in which aluminum is added near the end of pour or after shut-off, intermediate semikilled steels, in which aluminum is fed uniformly throughout the pour, and semikilled steels requiring no mold deoxidation. In an attempt to cover the ingot structures obtained by the range of practices reported in the preceding survey, three series of experimental heats were made using increasing amounts of aluminum, silicon and titanium for ladle deoxidizers. The ladle deoxidizers were added as stick aluminum, 50 pct ferrosilicon and 20 pct ferrotitanium (4 pct carbon), respectively. Two methods of studying ingot structures were used. Ingots were removed from production, burned longitudinally and machined to allow observation of the central pipe and coarse blowholes. During the machining operation much of the finely porous subsurface structure was obliterated. Accordingly, observations were also made

Jan 1, 1947

By AIME AIME

The following financial report of the Treasurer of the United Engineering Society is published for the information of members NEW YORK, February 15, 190S. To the Board of' Trustees, United Engineering Society I beg to submit herewith the report of the Treasurer as of December 31, 1907. Your attention is called to the fact that the resources and liabilities, receipts and disbursements statements cover all the financial transactions of the United Engineering Society from its organization up to December 31, 1907. The income and expenses of operating the building during the whole operating period from December 1 to December 31, 1907, somewhat in excess of twelve months, are given. Included in the expenses, amounting in all to $52,647.11, will be found an item entitled "Building Equipment (construction account)." The expenditures under this item were not made for the operating expenses of the building, they represent a construction account, properly speaking, covering expenditures for furnishings and equipment of the building. The Founders' Agreement specifically provides for this class of expenditure under the provision that the Founder Societies shall each be liable for a charge not to exceed $200,000 of principal, which shall include the land and building completed and ready for occupancy, together with the " furnishings, equipment and personal property therein." Certain details of equipment are yet to be supplied, and it. is proposed in the near future to call upon the Founder Societies for an assessment on their respective land and building funds to cover this item of building equipment. Such action would enable the item of $10,039.85 to be transferred to the income account and reduce correspondingly the assessment

Mar 1, 1908

By C. C. Wright, R. J. Day

Although data on the exact tonnage of recoverable coal silt are not known, the quantity produced in 1943 was estimated to be over five million tons for the anthracite region of Pennsylvania alone. Since that time the recovery of the No. 5 buckwheat size previously included in silt estimates has increased greatly thus reducing the total silt tonnage. As a compensating factor, however, the methods of recovering silt previously escaping into the rivers and streams have been markedly improved so that the net figure may not have changed materially. Comparable estimates for bituminous coal are lacking, but undoubtedly the silt represents a significant tonnage. With the trend toward increased wet cleaning of the smaller sizes of bituminous coal, it is to be expected that even greater quantities of silt will be available in the future. The raw silt from anthracite collieries usually contains a high mineral matter content, but technological developments in fine coal cleaning have been making rapid advances and it appears probable that more extensive use of these methods will be employed in the near future. Bituminous coal silt in many instances contains a similar high mineral matter content. As with anthracite silt, however, the cleaning of this material, where necessary, appears both technologically and economically feasible. With a view to upgrading the size and value of silt, considerable laboratory and pilot plant work has been conducted by a number of organizations on what is commonly known as pelletization. Actually the process is one of extrusion in which the moist silt is extruded from a die in the form of rods, which usually break into relatively short lengths—a few inches long—as they fall from the die. Fig I is a photograph of some extruded 3/8-in. diam pellets and of the anthracite silt from which they were produced This technique of producing larger sized material from fines is by no means new, having been used extensively by the industrial carbon and clay industries for years.' The application of the process to coal silt appears, however, to be relatively new. The first major program of investigation dates back only to July 1945, when a group of engineers representing the Anthracite Institute, The Pennsylvania State College and the J. F. Pritchard and Co. conducted preliminary tests on the extrusion of anthracite silt at the Floridin Co. plant at Warren, Pa. Since that time these three organiza-tions—individually, together, and in cooperation with other interested groups— have actively pursued work on various phases of the problem. Much of the early history and details of the laboratory and pilot plant work by the Anthracite Institute, has been reported by Mulcey and Eckerd.2 It is the purpose of this paper to report additional information on the process, especially with respect to the factors influencing the quality and use properties of the product, and the current develop-

Jan 1, 1949

By J. W. H. Clare

An equilibrium isotherm at 550°C is given for ternary alloys rich in aluminum containing 0 to 15 wt pct Cr and 0 to 20 wt pct Mn. Phases encountered are: aluminum solid solution; stable temary compound G; and MnAl8,. In addition, a limited number of alloys were annealed at 450°C to check for differences from the 550°C isotherm. These experiments limited the composition of the G phase at 550°C and further experiments established that the G Dhase is not stable above 590 ± 1 °C. RAYNOR and Little1 established several equilibrium isotherms using aluminum-rich alloys containing up to 5 pct of the elements chromium and manganese. These isotherms showed that, in addition to an a solid solution and the two binary intermediate compounds 8 and MnAl6, a stable ternary compound ex-isted in the system. This phase was called the G phase because of its ghostly appearance in micro-sections. Little, Raynor, and Hume-Rothery2 found a similar phase in binary aluminum-manganese alloys and, as a result of their experiments, concluded that the G phase was a metastable phase existing in the aluminum-manganese system. This phase was stabilized by the addition of chromium. The constitutional work of Raynor and Little,' although showing the existence of the G phase in the aluminum-chromium-manganese system, did not establish precisely the composition limits of the phase or the temperature above which the phase became unstable and disappeared from the system. The work described in this paper was undertaken to provide this information. An examination of the previous work' showed that an isotherm at 550°C would provide the required data regarding composition in the shortest possible time, as the (a + G) phase field narrows considerably at higher temperatures. The same work showed that the G phase ceased to exist between 580° and 595°C. A more precise estimate of the transformation temperature would therefore be obtained by annealing selected alloys at successively higher temperatures beginning at 580°C. EXPERIMENTAL PROCEDURE 1) Materials Used—The experimental alloys were prepared from four master alloys containing 15.00 w pct Cr, 15.28 wt pct Cr, 19.80 wt pct Mn, and 19.38 wt pct Mn which were made from super-purity aluminum, electrolytic chromium, and electrolytic manganese. The aluminum was of 99.996 pct purity, the principal impurities being copper, iron, and silicon. The chromium and manganese were 99.9 pct pure, the principal impurities being antimony, calcium, and magnesium. 2) Preparation of the Experimental Alloys—The alloys were prepared in 20-g quantities by melting together the requisite amounts of master alloy and aluminum in an alumina-lined crucible and, after thorough stirring with an alumina rod, cast into a cold copper mold to give ingots 1/4 in. in diam and 3 in. in length.

Jan 1, 1960

By H. A. Bright, H. C. Vacher, J. G. Thompson

The methods employed for the determination of oxides and oxygen in ferrous materials may be roughly classed in two groups, "wet" methods and "hot" methods, the first group including the iodine, electrolytic, mercuric chloride, hydrochloric acid, nitric acid, and chlorine methods; the second group including the vacuum-fusion and hydrogen-reduction methods. The wet methods depend upon preferential solubility in a selected medium to separate the metallic portion of the sample from the oxygen-containing constituents. Subsequent analysis of the insoluble residue permits the isolation and separate determination of individual oxides and compounds. The hot methods depend upon the reduction of the oxide constituents of the sample by means of carbon or hydrogen at elevated temperatures. With the exception of the recently developed fractional vacuum-fusion method, the hot methods do not identify individual oxides and compounds but yield only a single value representing the sum of the oxygen contents of several or all of the oxide constituents present. With such diversity in the principles and aims of the different groups, it is not surprising that concordance of results by different methods has usually been difficult to obtain. The present cooperative attempt to define more rigorously than has been possible heretofore the accuracy and limits of usefulness of the various methods, originated in correspondence between Dr. John Johnston, Director of Research of the United States Steel Corporation, and other interested metallurgists. The plan was, briefly, to submit identical samples to a number of laboratories for analysis by different methods and to collate the results of these analyses. The project was endorsed by the Iron and Steel Division of the American Institute of Mining and Metallurgical Engineers at the annual meeting in February, 1933, and has been conducted under the joint sponsorship of the Iron and Steel Division and the National Bureau of Standards. The latter organization undertook

Jan 1, 1937