Search Documents

By Bianca Proença

Fotocatalisadores de nióbio foram obtidos por anodização a 15 V, utilizando uma solução de K2HPO4 10% p/p em glicerol anidro como eletrólito por 15 minutos. As amostras foram caracterizadas por difração de raios-X para avaliação da estrutura cristalina obtida. A fotodegradação do glicerol (utilizado como agente de sacrifício) foi avaliada pela técnica de cromatografia líquida de alta eficiência.

Aug 16, 2017

By Keulla Venya Urbano e Silva, Marcelo Quintão e Silva Marchetti, Rafael Silva Marcelino, Rafaella Bicalho da Rocha

Comparative study between standard and BigFLUX matrices for high intensity magnetic separation pre-concentration (WHIMS) stage for iron ore. The evaluation was carried out on GAUSTEC’s pilot equipment for samples from Viga Mine’s operation. Samples in different feed iron content on rougher stage were evaluated in 46 experiments with matrix variation. The analisys compared chemistry, mass recovery and metallurgical recovery results to define the most efficient matrix to use in a pre-concentration stage.

Oct 3, 2019

By Glaucon Medeiros Silva

Este trabalho técnico tem por finalidade apresentar a evolução dos ensaios de porosidade em pelotas de minério de ferro. Apresentando as diversas formas de realização deste tipo de ensaio a não correlação entre eles, pois cada método possui uma finalidade distinta e como se ocorreu a evolução do método volumétrico (ótico) desde sua realização manual, na década de 1980, início de medições automatizadas na década de noventa e sua total automatização a partir da década de 2010 até o ano de 2019.

Oct 1, 2019

By Jackson Teixeira de Oliveira, Douglas Batista Mazzinghy, Vanderson Eney de Matos, Alexandre Camilo Leles de Figueiredo

This work studied the effect of different ball sizes in the secondary grinding stage of Samarco. The Moly-Cop Tools 3.01 spreadsheet was used for models calibration and simulations, considering grinding balls topsize of 15, 20, 25, 30 and 35mm diameters. A normal specific selection function up to the largest fed ore particle size (840μm) was obtained. The higher generation of fines and compliance with particle size specifications (+ 74μm and -44μm) proved to be more favorable for smaller ball sizes. The specific energy consumption was lower for the 15mm ball (10.7kWh/t), increasing up to the 35mm ball (13.0kWh/t). Although smaller diameter balls seem to be the best option for the size specifications, some factors may limit their use, such as: the higher generation of specific surface area; and the amount of ball purge in the discharge of the mills.

Oct 3, 2019

By Julio César de Oliveira Melo, Giuliano Felippe Soares, André Dias Leite

A resolução de problemas na operação industrial é algo complexo e precisa ser baseada em dados, muitas vezes diversos e não estruturados. Este trabalho traz uma abordagem em big data para dar visibilidade dos problemas em sistemas industriais, trazendo insights que permitam sair da intuição para assertividade, contruibuindo, assim, para redução do tempo de detecção e resolução de problemas.

Oct 1, 2019

By Fabio Lerbach

The Powder Charcoal Injection in the main burner of the rotary kiln of Pelletizing Plant aims to reduce natural gas consumption and consequently cost reduction with thermal energy. This paper presents the technology, the injection process and the advantages of using powder charcoal to substitute natural gas.

Oct 30, 2017

By Elen Mancini Santi Paulettor, Vinicius Calheiros, Eduardo de Oliveira Cabral

At this paper, Eirich will present its new tool for sinter analysis integrated to the sintering control system. For stabilization and optimal, continuous control of the sintering process, QualiMaster MT1, a device was developed which guarantees fully automatic representative sampling and material analysis and thus a high and stable sintering quality. Mining tailings often has a considerable proportion of valuable substances. In addition to this work, we will also present our mixing technology that allows the economic recovery of these mining tailings.

Oct 1, 2019

By José Francisco Cabello Russo, Késsius Bortolan Menezes, Henrique Dias Gatti Turrer, Denílson Rodrigues de Araújo

With the start-up of the Minas-Rio system, Anglo American, in Conceição do Mato Dentro, MG, in 2014, a methodology was also implemented and certified to perform the tests to obtain the results of TML (Transportable Moisture Limit). Such a parameter provides the maximum moisture content contained in the material that could be transported without the risk of the cargo liquefaction process, which could lead to incidents such as the tipping of ships carrying iron ore concentrate in bulk on the deep water. This means that when loading a ship, the moisture content of the material to be transported should not be higher than the TML reference value, obtained in a physical test and intrinsic to the material. Should this occur the charging may be rejected. From 2014 a downward trend was observed for this reference parameter in the Minas-Rio system, with results approaching the moisture of the filtered product, bringing risks to the operation of the project. In this way, an investigation of the possible causes for understanding this downward trend was required.

Oct 3, 2019

By Fábio Heiji Yamada, Marcelo Koiti Fugihara, Ruano Fonseca Araujo

Conception the simulation and optimization technologies for industrial processes applied in the mining environment: tools and methodologies. Clarifications provided about the differences of these techniques when compared with static analysis (intuition, use of static spreadsheets, etc.). Presentation of practical cases at several big mining companies in Brazil. These projects will be presented and illustrated through dynamic simulation models developed at those companies, each one with its set of objectives, scope and results (for example: sizing the number of equipment, silo, piles related to the mining processing, logistics, ROM transportation, mine operations plan, etc.).

Oct 3, 2019

By Rodrigo Martins, Mauro Trindade

I Reduction of energy consumption in air compressors by the implementation of individualized load control. Reduction of 3,5% from Jun / 18.

Oct 3, 2019

By Denise Freire Duarte

Desclassificações de corridas por elementos fora da faixa de especificação do tipo do aço que está sendo produzido impactam negativamente nos indicadores da empresa. É esforço contínuo os projetos de melhoria e ações implantadas para a redução dessas desclassificações. Quando uma corrida é desclassificada, há um custo para refazer a corrida perdida, ocorre um processo de reclassificação que fica em estoque aguardando aplicação, perde-se tempo e pontualidade na produção entre outros impactos. Portanto identificar a causa raiz do problema e atuar em ações efetivas e bem implantadas são as chaves para a resolução do problema e melhoramento do processo. O fósforo é um elemento que deve ser controlado pois é item de norma para atendimento às especificações pois impactam na fragilização do material. Este trabalho mostra a análise realizada na busca da causa raiz das ocorrências das desclassificações de fósforo.

Oct 30, 2017

By Leonardo Semedo de Mattos Siqueira, Renata Ferreira Muller

The Granulometric Ratio (RG) is one of the most important indicators related to the pelletizing product. Through it, it guarantees good permeability of the bed of pellets, optimization of the thermal cycle and, thus, better results of physical quality and consumption of the energy matrix. To guarantee this indicator, it is necessary that the processes of agglomeration of pellets, classification of raw pellets and screening of burned pellets are under control of certain parameters and with a level of stability assured.

Oct 1, 2019

By Walter Luiz Castro dos Santos, Leandro Resinentti Zanon

In the production of iron ore pellets, one of the factors that strongly influence the cost of ore-pellet processing is the specific consumption of natural gas that occurs during the thermal processing stage of the pellets. The filtration process is the step where the adequacy of the moisture percentage of the retained pulp occurs, so that subsequently there is the processing in the subsequent stages of the pellet formation and hardening of pellets. The water contained in the raw pellet is withdrawn at the stage of thermal processing. For this purpose, the literature indicates the demand of 600 Kcal/kg of water for the heating and vaporization of the moisture of raw pellets. The statistical analysis of the performance data of a pelletizing plant showed that for each decrement of 0.1% of water in the retained pulp is equivalent to the reduction of 0.091 Nm3 in the consumption of natural gas per tonne of pellets produced. Thus, the proper performance of the filtration stage is essential to reduce the percentage of pulp moisture retained and consequently to increase the energy efficiency of the pelletizing furnaces. The aim of this article is to present the main steps in conducting a work to increase the filtration performance to reduce the percentage of retained pulp moisture and the positive impacts on the specific natural gas consumption of a plant Pelletizing.

Oct 1, 2019

By Jefferson Monteiro Oliveira

A eficiência das turbinas a vapor de condensação é diretamente alterada pelo desempenho dos condensadores de superfície e estes últimos são negativamente afetados não somente pela entrada de ar no sistema, mas também por entupimentos e diminuições nos fluxos de água de refrigeração. Entretanto, qualquer uma das fontes de diminuição da eficiência do condensador geram efeitos similares dificultando a distinção entre elas ou a contribuição de cada uma para a queda no desempenho. Então a decisão pela manutenção tem aspectos claramente econômicos. Este artigo apresenta métodos para avaliação das fontes de perda de desempenho em condensadores e suas consequências na geração de energia.

Sep 25, 2017

By Flanelson Maciel Monteiro, Marcondes Mendes de Souza, Mauro Froes Meyer

This research is based on a bibliographical review of a field work that was done in the municipality of Parelhas / RN. The area explored, in turn, is known for its richness of mineral resources that are present in pegmatitic rocks. The general objective of this research is to characterize the main properties of the pegmatites and quartzite, in order to verify the heterogeneity of the elements, to raise a possible viability of extraction for economic purposes. The quartzite also presents a siliceous chemical composition. This rock is a source of bricks and silica refractories used in the steel industry and for the preparation of the blast furnace bed, ornamental rock used in different ways (rustic, carved, polished, among others). However, this research resulted in preliminary data, but it would be interesting to be more detailed in order to evaluate the economic viability of these rocks.

Oct 3, 2019

By Wolfgang Linden

One of the most important factors in successful electric steelmaking is the continuous observation of the process and the reaction to it. Traditional electric arc furnace control uses mainly direct controls which are based on the electric power input. Not considering the furnace conditions will necessarily lead to suboptimal operation in terms of energy consumption and productivity not fully utilized.The ARCCESS FEOS (Furnace Energy Optimization System) includes the simultaneous control of the transformer tap, impedance operating point, reactor tap, burner and carbon injection, and DRI charging control. FEOS has proven in practical operation benefits of high melting yields, no interruptions through switch offs in borderline temperature area, rapid reaction, reproducible and efficient electrical energy input and short power-on times.

Jul 30, 2018

By Samuel Vasconcellos

Em plantas de separação do tipo PSA ocorrem oscilações na vazão de ar intrínsecas a este processo, devido à repressurização dos vasos pré-purificadores ser feita em intervalos muito curtos. Por meio da instalação de um buffer tank foi possível tornar a coluna de destilação mais estável, aumentando a produção de líquidos, reduzindo a demanda de energia e otimizando a pré-purificação.

Jul 31, 2018

By Gabriel R. Royo

This paper will cover a back up roll bearing technological upgrade, being implemented at the TERNIUM SIDERAR Hot Strip Mill (HSM), in San Nicolas, Buenos Aires, Argentina. This change was motivated by increased operating loads, which caused the original bearings to be outside the designed bearing rating. The problems were first identified by bearing seizures in some stands, and later followed by cracks forming in the back up roll neck areas due to fatigue and overload. MORGOIL engineers worked together with TERNIUM SIDERAR engineers in analysing the problem and to upgrade the mill with the newest and most economical technology. The upgrade consisted of changing the bearings to the latest generation MORGOIL bearing: the KLX, which within the same space, increases bearing capacity around 25%. This was accomplished re-utilizing all chocks. The new bearing allowed for a re-design of the geometry of the back up roll neck, making it much stiffer than the original design, and eliminating fatigue failures. In addition, an upgrade to hydraulic mounting and dismounting using the MORGOIL® HB lock was also implemented, as well as changing to the newest MORGOIL® HD seals. With the MORGOIL® KLX® upgrade, TERNIUM SIDERAR HSM increased load capacity, allowing them to roll products that were not even considered decades ago. Both older oil film bearings and roller bearing mills have been successfully upgraded while reusing existing chocks and in many cases rolls. Solutions are customized to the customer’s equipment and goals.

Oct 30, 2017

By Álvaro Lúcio

This paper outlines the DPC process as na economic and environment friendly option for the use of cultivated forest as a source of raw material for metallurgical charcoal.The DPC process was specially developed to bring logistic, environmental, technical, economic and global energy efficiency when compared to termal1 the existing biomass carbonization process. The DPC process utilizes the volatile materials (condensable and non condensable) as a source of the energy required by the carbonization process guarantying its complete combustion. As result the DPC process avoids the burning of termal1 the loaded wood, obtaining a higher charcoal to biomass yield, and avoids the emission to the atmosphere of polluting gases. Gases emitted by the carbonizing wood have na energy termal1e enough to dry the wood soon after its harvesting. By avoiding the storage in the field during na average of 150 days, the resulting economy is quite significant. As a termal1e1 the higher charcoal to biomass yield na termal1e1e economy is obtained through the reduction of the cultivated forest term. This paper emphasizes the economic advantages of the DPC process.

Aug 16, 2017

By Diogo Tenório dos Santos

This property has been studied to characterize the strength a metallic material exhibits when it is machined so it can be regarded as its typical behaviour. As such, it may even be considered as an intrinsic material property. It is usually measured by an index called Coppini index, which is expressed by the ratio between the removed mass of a cutting tool caused by wear when it is used for machining and its initial one for a certain set of machining parameters. In this investigation, the tests were therefore conducted by an established set of parameters, namely feed rate, cutting and depth rates, in which the same wear mechanism took place in both ferrous alloys: AISI 4140 and AISI 316 steels. They were chosen based upon their increasing ordinary machinability indexes. The initial and final mass of the cutting tool were measured by an analytical scale with 0.01 mg precision. Cylindrical rods of 50-mm diameter were machined and the CI indexes showed a remarkable difference between them: 0.080 for the first steel and 0.049 for the second one, i.e., AISI 316 steel presented better machinability than the first one. It was then possible to conclude that this method presents good results in terms of both reproducibility and adequacy for machine shop conditions and it may be applied in a foreseeable future, mainly for metallic materials that have rather low machinability indices.

Jul 31, 2018