Search Documents

By José Divo Bressan

Present work examines material surface damage by cavitation erosion of metals or the wear phenomenon from water bubbles collapse near the metallic surface. Material surface damage by cavitation erosion is due to wear mechanisms of liquid micro-jets impingement and shock waves. Experimental cavitation in tap water was investigated, using the proposed new design of compact rotating disk equipment. In this device, a rotating disk with cavitation inducers and specimens fixed on it ran in tap water to provide cavitating flow at constant high speed of 47.9 m/s similar to service conditions in pumps and propellers. Two types of cavitation inducers in the rotating disk were investigated: through-holes and pins. Carburized cast iron, aluminum, brass and bronze specimens were tested in this device. The cavitation damage mechanisms were observed by scanning electron microscope. Surface damage in the specimens was measured by mass loss and plotted in graphs of mass loss versus running time. After 25 hours testing, the specimens surface showed pitting formation and mass loss. All specimens presented surface damage: pit diameter size was about 100 or 150 to 300 micron. In aluminum specimen, damages by burned pit formation and plastic deformation could be seen, however, the mass loss was lower than the expected, possibly due to alumina film formation. Present equipment had quite good test reproducibility when compared with results from literature.

Jul 31, 2018

By Amanda Coutinho Campanatti

O objetivo desse trabalho é caracterizar o processo de delaminação, tanto em Modo I como em Modo II, de abertura de trinca. A densidade e porcentagem de fibra do compósito carbono-epóxi foram calculadas para caracterizar o compósito. O inserto, para simular o início da trinca, foi feito no processo de fabricação dos compósitos a fim de manter sua integridade. Pelo mesmo motivo o corte foi feito a jato d’água. Para caracterização da delaminação foram feitos ensaios de DCB (Double-cantilever Beam) e ENF (End-notched Flexure), segundo as normas ASTM D5528 e ASTM D790-10, sendo ambos realizados na máquina universal de ensaio MTS, capacidade de 250 kN. A fractografia em Microscopia Eletrônica de Varredura (MEV) foi feita a fim de identificar os mecanismos de dano durante a propagação da trinca. Foi possível concluir a fabricação do compósito, bem como do inserto, é viável. Porém, houve aparecimento de bolhas, por causa da baixa pressão da bomba a vácuo. O corte a jato d’água manteve a integridade do compósito. A rigidez alta do compósito pode ser comprovada por meio das propriedades mecânicas obtidas pelo ensaio de tração. Os valores de GIC e GIIC estão dentro do esperado pela literatura, sendo GIIC maior que GIC por causa da presença de um capo de compressão no ensaio em modo II, enquanto que em modo I é abertura pura por tração.

Aug 7, 2018

By Carlos Vinícius Domingos de Carvalho

As perdas geradas nos processos de uma Aciaria contribuem de forma significativa para a perda metálica do processo. Eventualmente, mesmo com uma operação correta, do ponto de vista de características do produto, pode ocorrer comprometimento do ponto de vista econômico, e uma forma de redução direta dos custos e aumento de performance é a redução das perdas geradas no processo. Desta forma, tornou-se importante realizar um estudo para reduzir as perdas metálicas na Aciaria. Foi utilizado a metodologia Seis Sigma, sendo estratificadas as perdas por processo na Aciaria, onde as maiores perdas na rota dos processos de Lingotamentos Contínuos foram: perda no Distribuidor (24,7%), corte de sequência (17,5 %), retorno de corrida por baixa temperatura do aço na panela (16,3 %); perda por obstrução da válvula da panela (8,8 %). A perda metálica foi reduzida em 50,8%. Além da redução expressiva das perdas, houve uma grande contribuição em relação à compreensão dos modos de falhas para apropriação correta das perdas, tornando as informações mais seguras e facilitando o tratamento de possíveis falhas no processo.

Oct 30, 2017

By Lucas Coelho da Silva

Nesse artigo, foram desenvolvidos experimentos que visam determinar e avaliar a microestrutura presente em tubos de polímero reforçado por fibra de vidro. O trabalho apresenta uma breve introdução do processo de obtenção das fibras de vidro através da pultrusão e suas vantagens e aplicações. As técnicas de caracterização microestrutural são listadas e explicadas bem como a finalidade de se realizar esse procedimento. As amostras foram envelhecidas no forno a uma temperatura próxima da deterioração e depois resfriadas à água e ao ar. Após isso, foi feito ensaio de achatamento nas amostras a fim de se determinar se o envelhecimento afeta o grau de deformação da amostra até ela se romper.

Aug 16, 2017

By Tadeu Messias Donizete Borba

A soldagem com elevado aporte térmico é uma das alternativas adotadas pelos estaleiros para aumento da produtividade nas operações de união de materiais. No entanto, os ciclos térmicos gerados durante a soldagem podem provocar transformações microestruturais prejudiciais à tenacidade na zona afetada pelo calor (ZAC). Este estudo teve como principal propósito realizar a caracterização microestrutural e avaliar as propriedades mecânicas da ZAC do aço naval Sincron EH36 produzido na Usiminas por laminação controlada seguida de resfriamento acelerado em comparação com um aço de mesma classe de limite de escoamento produzido convencionalmente, ambos soldados pelo processo ao arco submerso em dois níveis de aporte térmico: 76 e 130 kJ/cm. Foi observado que a presença de uma microestrutura mais refinada nas diferentes regiões da ZAC, associadas ao menor tamanho de grão do metal base e ao menor carbono equivalente, foram os principais fatores que contribuíram para a excelente tenacidade da ZAC do aço Sincron em comparação ao aço convencional. Os resultados obtidos mostraram que é possível obter juntas soldadas com excelentes propriedades mecânicas ao se empregar aço Sincron para a soldagem com altos aportes de calor, e sua utilização pode ser uma estratégia para otimização dos tempos e custos de fabricação na indústria naval.

Aug 8, 2018

By Mariana Carla Mendes Rodrigues

The present study deals with the effects of strain rate on the functional behavior of NiTi thin wires. The samples, in the austenitic condition at room temperature, were mechanically cycled 20 times by loading up to 6% strain followed by complete unloading, at 25°C. Four different quasi-static strain rates were assessed: 1x10-4, 1x10-3, 1x10-2 and 5x10-2s-1. The functional properties are described by means of critical stress to induce martensite, stress at maximum strain, energy dissipated per cycle and residual strain. The sensitivity of repeated cyclic deformation to strain rate is also analyzed in terms of phase stability. The results show that the fluctuation in the loading plateau, due to non-homogeneous transformation, increases with increasing strain rate. During cycling, it is observed that higher strain rates result in lower critical stress to induce martensite after the 5th cycle. However, the stress at maximum strain is higher at high strain rates, regardless the number of cycles. The accumulation of residual strain also increases with the strain rate due to the higher applied stress. During unloading, both the elastic deformation of stress-induced martensite and the reverse transformation seem to overlap at high strain rates. The dissipated energy behavior changes between the 1st and 20th cycle. No martensite is stabilized after training, but the intensity of the X-ray diffraction peaks of austenite increases with strain rate, as a result of stress relaxation.

Aug 17, 2017

By Caio Trindade Almeida, Tharcysio Oliveira Rocha Paiva

Tharcysio de Oliveira Rocha de Paiva2

Oct 3, 2019

By César Junior dos Santos, Fábio da Silva dos Santos, Robson Rodrigues Martins

Tailings disposal has been a recurring theme of research in the major mining process development centers. This is due to the great interest of companies in reducing the social and financial impacts of their environmental liabilities. Another major driving force behind the search for new alternatives is the recent cases of environmental accidents in Brazil and abroad. According to the International Commission on Large Dam (ICOLD), two major accidents per year involving dams are reported worldwide. Hence, we realize that the analysis of the topic as well as the search for solutions becomes a challenge for both entrepreneurs and research institutions. In this work, a case study of the Herculano Mining will be carried out, working in the extraction and processing of iron ore. The main stages of the study are: technological characterization of tailings from the beneficiation process, analysis of filtration processes of this material for disposal in piles, bench tests and evaluation of the performance of the industrial facilities of the company in question. Herculano has an installed ceramic filtration equipment that faces operational difficulties in certain types of ore. At first, all the possibilities of adjusting this process will be analyzed so that it can filter the necessary mass of waste, acting in the rheology of the pulp (sedimentation, flocculation), regeneration of the ceramic plates and adjustments of the machine (filter), in order to obtain the best condition.

Oct 3, 2019

By Jörg Schwelberger

Government regulations around the world concerning environmental care are becoming more stringent, also including regulations and restrictions of depositing and use of dust, sludge and slag generated in the iron and steelmaking process. With this scenario, by-products such as iron containing dust, sludge, oxide fines, mill scales and slag, become a valuable resource and recycling may be a profitable activity within a plant. Up to ten percent in mass of the total steel output of dust, sludge and mill scale by-product materials and more than 40% of slag by product are generated within an integrated steel plant with an iron content ranging from 50% to 65% for fines and up to 25% for BOF-slag. Slags are being widely recycled and used in the cement industry, as is the case for BF slag, and in the construction industry in the case of BOF slags and EAF slags. However, value of BOF unmodified slag is typically low and environmental regulations limit the usage of the unmodified BOF slag. This paper describes innovative solutions for recycling of fines using cold briquetting technology and the modification and granulation of slag from steelmaking that increase the value of the by-product and yield a marketable product.

Aug 16, 2017

By Gilmar Ferreira Bataglia

The possibility of parameterization of hot tensile data together with creep data is investigated, for Aluminium Alloy 7475-T7351. This study represents part of a broader research program aiming at the validation of a methodology recently proposed for analyzing both kinds of data together, considering different metallic materials. The results presented in Part 1 of this work, were analyzed according to 4 traditional methods of the literature for parameterization of creep data, namely: Larson-Miller, Orr-Sherby-Dorn, Manson-Succop and Manson-Hafferd. The compatibility of the hot tensile test results with those of creep is remarkably good, indicating the possibility of using both kind of data together also in extrapolation schemes. The criterion proposed for equivalence between hot tensile and creep data is verified to work well also for this kind of material, under the present experimental conditions.

Aug 8, 2018

By Rodrigo Fina Ferreira, Jacek Kolacz, Luciana Gois, Neymayer Pereira Lima

The recent developments on the sensor detectors together with the higher capacity of the machines, due the high-speed computing recent advances, have made possible extending the application in the mining industry. The use of x-ray fluorescence, x-ray transmission and radiometric sensor based sorting can selectively remove gangue minerals in different size fractions for different minerals. This paper summarizes the potential application of SBS for an iron ore in three size fractions aiming to increase the %Fe after the removal of particles with main gangue minerals associated. Pilot plant tests were carried out with samples of iron ore in different size fractions and different content of hematite and gangues. The use of x-ray transmission sensor showed the possibility to increase the %Fe from about 63% to above 68% for particles below 80mm and 45mm, after the removal of low density particles. The presence of fines on the feed affected the performance of the SBS X-rays transmission machine, especially for the fine fraction feed. The mineralogical determination, carried out to know the association between hematite and gangue minerals, and the density of the particles on the feed, can be used to preview the quality of products of the x-transmission sorting process.

Oct 3, 2019

By Benito Barbabela Silva, Michel Garant, Mathieu Dubé

Pellets market challenging scenario has stimulated pelletizing experts to pursue innovative alternatives to process development in order to increase pellets competitiveness vis-à-vis sinter. When it comes to indurating process, pelletizing productivity is still limited and its OPEX inflated by the lower input of carbon into mixes due to quality impairment caused by magnetite formation in pellets core. This obstacle led to the rethinking of carbon distribution strategy within the green balls. To achieve such purposes, COREM through its precompetitive research program dedicated to its members, has proposed the layered pellets®, a two-stage balling technology. Balling in disc and pot-grate tests in COREM’s pilot plant were carried out to proof the concept, support the arising technology and evaluate its potential. According to first results, while CCS strongly improved, tumble and abrasion indexes as well dynamic LTD must be further investigated. Tests on four classes of equivalent carbon content pellets to evaluate layering strategy gave very good perspectives concerning the increase of productivity, and the reduction of fuel consumption and GHG emissions.

Oct 1, 2019

By Francisco Morganti

The market requirements which strip processing lines have to deal with have altered significantly within the last decades. Particularly, the production has to be economical and ecological efficient and processing lines have to cover a broad product portfolio. Already existing plants either directly or indirectly are competing with new plants, which are equipped with the latest technologies. The “Special Strip Processing Equipment” is designed to be integrated easily and within small downtime phases in existing lines. All single machines can be delivered in short time “ready-to-perform” with a tested and proved automation system. Thus, the competitiveness of existing lines can be increased immediately with less effort. To find out which machines can be reasonably implemented SMS group offers an “Efficiency Check”. A special proceeding is used by experts to find out quickly which machines will have the largest effect on the efficiency of the line while demanding at the same time the smallest expense.

Aug 17, 2017

By Kyle T. Chomyn

Multi-disciplinary engineering analysis and advanced modeling techniques were used to identify and develop low cost design modifications to improve a blast furnace hot blast air distribution main that experienced frequent refractory failures. Piping flexibility analysis helped identify the root causes of refractory damage and determine the need for new expansion joints. Finite element analysis was used to optimize a custom-designed elbow-to-elbow tie-rod system, which ensures thermal expansion loads are not placed on connecting piping. Heat transfer coefficients through the elbows were estimated using computational fluid dynamics (CFD) flow modeling. The cast refractory design was changed to a more reliable brick refractory design. Excessive draft was occurring during furnace back-drafting, so the system was assessed using CFD, and a passive flow-reduction spool was designed. This firstprinciples engineering design approach allowed for optimization and verification, ensuring that the new design addressed the root cause of the previous deficiencies.

Aug 17, 2017

By Enif Gutiérrez Guerrero

Inclusion deposition is still a standing problem in the continuous casting of steel since the deposition of alumina inclusions inside the SEN affects the productivity and the product quality. The present work studies the factors involved in the inclusion deposition at the nozzle and the effects of inertial, gravitational, buoyant, pressure gradient, and Saffman forces on the inclusion trajectories. The results show that the inclusions reaching the nozzle, only 30% get deposited along its walls mainly at the Upper Tundish Nozzle (UTN). This area of higher deposition is identified close to a low static pressure and a high turbulent kinetic energy dissipation zones where the effects of the gravitational and buoyant forces do not promote a significant inclusion radial movement since these are aligned with the direction of the flow stream lines. In contrast, in this zone, the Saffman force shows an important effect on the deposited inclusions, slowing down the inclusions in the vertical axis and increasing their radial movement.

Aug 17, 2017

By Gergö Rimaszéki

Due the fast growing of pig iron and steel in the last years associate with some mineral resources changes (Hematite?Itabirite), has been checking the sinter feed degradation. The typical sinter feed (0.15;-6.3 mm) has become limited and the rapid growing production resulted in more and more fine ore (< 150 µm) availability in the market. The sinter plant operators are facing several new challenges since the mixing and granulation- and the sintering behavior of the fines containing mixtures often differs from the traditional sinter feed´s behavior. The utilization of fines in the sinter plants might increase the process water consumption required for the mixing and granulation process or even the solid fuel consumption, which effects the operational cost of the plant significantly. The current study presents an overview about Outotec´s laboratory facilities and competence regarding the mixing and granulation of fines in different equipments. The usage of high intensity mixers (HIM) – vertical and horizontal as well – showed to be the most effective, based in cold agglomeration tests in small scale, in case of fine ore handling. Permeability and particle size distribution curves are used to evaluate and demonstrate the efficiency of the different equipments. Outotec´s ”Know-How” with the different type of mixer and the modern laboratory facilities provide an excellent opportunities to optimize the mixing and granulation procedure and utilize up to 100 % pellet feed

Aug 17, 2017

By Thomas Schanz

Current steel market conditions require small investments only to lower operational cost. SMS Concast has developed new products which optimize continuous casting process cost for long product steel production. This paper describes a selection of three products. All three systems are patented (patent pending for CONDRIVE). CONSAFE, a non-radioactive mould level measurement system for reliable mould level measuring on open stream casting CCM’s; CONSTIR-MWS, an improved control software for electromagnetic stirrers which lowers energy cost by 35%; CONDRIVE, a brand new oscillation drive system which provides the features of a hydraulic oscillator, however with a cost efficient electric drive.

Aug 17, 2017

By Ernst Lindemann

The SMS group has developed the ultrasound technology “HD scan” for inspection of the internal quality of as-cast products. This method of sample analysis requires less preparation work and is safer than the current, most common technique of etching and/or sulphur printing. Furthermore, this technology offers a three-dimensional view into the sample of the cast product and thus more representative information for a better quality evaluation. The internal quality evaluation can be performed automatically and objectively by software based on clear statistical methods. A quantitative centerline segregation rating can be assigned to each sample, based on the size and distribution of segregates detected by the unit. Internal crack statistic (length, position, orientation, etc.) and narrow side profile can also be measured. Grain macrostructure can also be visualized which allows for a potential optimization of casting parameters like strand cooling, soft reduction or electromagnetic stirring. The accuracy of the new method was proven by parallel metallographic investigations of more than 100 samples of different steel grades and sample shapes. Automatic defect evaluation and classification was compared against macroetching results. It was found that HD scan identified more defects and the visualization of the macro structure could be performed in more cases than with macro etching. All tests, comparisons, further developments and analyses for various steel producers and steel treatment companies have been conducted at the HD scan unit, located at the SMS group headquarters in Düsseldorf, Germany (Figure 1). Based on the results, SMS group has designed a unit which can be used in industrial scale.

Aug 17, 2017

By Elton Douglas Heriger Pereira

Refratários de alta alumina apresentam boa refratariedade, elevada resistência mecânica em altas temperaturas, boa resistência à variação bruscas de temperatura sem se romper sendo utilizados em revestimento de panelas e válvulas siderúrgicas devido sua propriedade anfótero e ter aplicações sobre à ação de escórias básicas. Neste trabalho procurou-se avaliar o efeito de adições de 1,5; 3,0 e 4,5%p. de Nb2O5 em refratário de alta alumina, estes obtidos a partir de uma mistura de diversos tipos de alumina, 5,0 %p. ZrO2 nanométrica (TZ-8Y) e agregado de mulita, sinterizados em temperaturas de 1400 e 1600 °C. Como nestes refratários a ZrO2 não surte o efeito de microtrincamento, a formação de fase vítrea a partir de Nb2O5 e a incorporação de agregados ao refratário foram fundamentais nas propriedades obtidas. Foram avaliadas propriedades tecnológicas como densidade e porosidade aparente pelo método de Arquimedes, formação de fases por difração de raios-X e análise microestrutural por microscopia eletrônica de varredura e resistência ao choque térmico.

Oct 30, 2017

By Konrad Krimpelstätter

The need for more effective and flexible roll-gap lubrication technologies in hot and cold rolling mills is steadily increasing due to ever-greater requirements placed on the rolling process and the final products. In particular, the rolling of high-strength steels poses enormous demands for both the rolling mill and the coolant/lubricant to be used. The presented paper focuses on two innovative technologies for highly efficient roll-gap lubrication for hot and cold rolling, which were developed utilizing extensive knowledge and expertise about the tribological interactions in the roll-gap. The advanced work-roll lubrication package (A-WRL) for hot rolling and ESP mills is using specially designed mixer-nozzle units to mix the water/oil emulsion very close to the nozzles to minimize the risk for contamination and clogging. The nozzles are quickly exchangeable and are optimized to ensure uniform lubricant distribution, high plateout efficiency and minimum oil consumption. This eco-friendly solution does not require any chemical additives or cleaning agents and significantly reduces electrical energy consumption and work-roll wear. The roll cooling system on mill entry and exit side remains switched-on, which is of vital importance especially for highperformance hot strip mills. Minimum Quantity Lubrication MQL® represents a new generation of roll-gap lubrication technologies for cold rolling, which applies minimum amounts of pure rolling oil finely atomized with pressurized air directly onto the work roll surface. This allows controlling the oil film thickness depending on actual process and product parameters, providing increased lubrication flexibility, significant improvement of strip surface cleanliness through reduction of strip wear. MQL® was successfully installed and tested on two industrial tandem cold rolling mills in Europe. Advanced WRL and MQL® represent Primetals’ latest technologies that feature a robust and reliable system comprising standardized interfaces and flexible communication options. Both packages can easily be integrated into existing or new hot strip mills, ESP lines or cold mills.

Aug 17, 2017