Search Documents

By F. R. Lee

[WHEN the Bureau of Mines was established in July 1910, one of the problems immediately attacked by the new organization was the development of standard, for the design and testing of electrical equipment that could be used without fear of initiating fires and explosions in underground coal mules. Research and investigation by Bureau personnel, supplemented by the published results of similar work by European mining authorities, led to the establishment of standards or "schedules." which guide manufacturers in the design of many types of electrically operated machines and devices used in. underground coal Mining. By issuing these standards, Bureau personnel establish the requirements to be met by such equipment before it tan be approved by the Bureau of Mines as permissible for use in gassy coal mines. Every 2 years the Bureau of Mines publishes a list of equipment that leas been accepted as approved or permissible during the preceding 2 calendar years. This is done to inform the mining industry of the availability of the latest equipment for safe use underground.]

Jan 1, 1964

By Alla D. Mah

The need for more and better basic thermodynamic data for the oxides of many of the rare metals is evident to anyone who attempts thermodynamic calculations involving these substances. In continuation of a Bureau of Mines program to meet this need, this paper reports new experimental values of the heats of formation at 298.15° K. of the hexagonal crystalline variety of germanium dioxide and germanium dioxide glass. The values were obtained by means of combustion calorimetry and sodium hydroxide-solution calorimetry. The calorimetric results also made possible the derivation of values for the heat and entropy of fusion of hexagonal germanium dioxide at its melting point. The newly measured data were combined with previously known entropy and high-temperature heat content values to obtain heats and free energies of formation of germanium dioxide (in the hexagonal crystalline, glassy, and liquid states) over the temperature range from 298.15° to 2,000° K.

Jan 1, 1962

By Z Li, A Fleming, S Webster, L Snyman

Northparkes Mines is developing the E26 Lift 1 North block cave mine, which is adjoined to the existing E26 cave. This paper presents the challenges and methods used to design the ground support system during the feasibility study. Calibrated numerical simulations were conducted to forecast the levels of rock mass damage and to assist the ground support design. Generally, low to moderate rock mass damage is forecast on the extraction and undercut levels. However, poor ground conditions are expected in sheared and preconditioned zones adjacent the existing E26 cave. This will result in difficult ground conditions during development, undercutting and drawbell establishment. Empirical assessments were conducted to make sure the ground support system is able to handle both the static and dynamic load demand, and to accommodate the deformation values. A safety factor of 1.5 was used for the designs to cover the unknown rock mass conditions and potential for larger seismic events. Learnings from the E26 Lift 1 and SLC, also mining against the E26 cave, are incorporated into the design. Fibrecrete, mesh and resin bolts / mechanical anchors are the primary ground support system used, and cable bolts for intersections with a span of more than 6 m. Following undercutting and during the operating life of the mine, secondary ground support and rehabilitation will be required.

Mar 15, 2021

By F. Hassan, M. A. Arafa

At El-Gedida iron ore deposits there is a block of about 30million tons neglected due to its higher sulfur content due to the presence of barite gangue minerals. From this bluk by magnetic separation dual concentrates of high grade iron concentrate (~65%Fe and total Sulfur of 0.26%) and the second concentrate is barite of (60.87% BaO and total impurities of less than 3%).

Jan 1, 1999

By E. J. M. Jahnsen, I. Jauhari, T. Badrujaman, F. A. Stober, B. O. Wasmund, L. R. Nelson, T. Miraza, J. M. A. Geldenhuis, A. Taofik Hidyat

The role of dedicated operational support in the ramp-up and stabilisation of the FeNi-II furnace for ferro-nickel production at PT Antam?s smelter located in Pomalaa, Indonesia is described. The furnace was uprated to 32MW capability in a rebuild performed in 2005. This primarily involved installing a larger transformer, coupled with adoption of HATCH water-cooled copper plate, waffle and flanker coolers with integrated metal and slag tapblocks, HATCH air-cooled copper fin lower sidewall cooling and HATCH vertical sidewall binding system ? ?holddowns?. Following a smooth commissioning period, the progress in attaining the preliminary ramp-up target load of 24MW is described. This initial target was set by Antam, subject to some prevailing smelter equipment constraints, particularly kiln capacity. Stabilisation of the furnace operation is discussed, together with some of the specific commissioning and operational challenges surmounted by the joint Antam-HATCH team. These included: ?Mastering furnace integrity monitoring and operation with copper coolers, especially metal tapblock planned maintenance and repair strategies; ?Transition from traditional ?immersed electrode? to ?brush-arc? mode of operation approaching as closely as possible to the productive ?shielded-arc? mode of operation within existing equipment constraints; ?Reductant selection and control issues; ?Utilising the sophisticated furnace monitoring to provide detailed indication and warning of potentially destructive furnace upset conditions such as Si reversion and CO boils.

Jan 1, 2007

By Yoginder P. Chugh

Subsidence may be observed above partial extraction shallow room-and-pillar mines where the coal seam(s) is associated with weak and thick claystone in the floor. This paper presents results of subsidence studies at such a mine. During the 26-month study period, a time dependent subsidence causing a maximum vertical movement of 50 mn was observed. After a subsidence rate of 6.0-6.5 m/month for the first two months after development of mine workings, the rate decreased to 0.8-0.9 mm/month after 17 months. However, presumably due to settlement of barrier pillars, it increased therafter to 1.7 mm/month for the next 9 months. Angle of draw, based on zero subsidence, was calculated to be about 29 degrees. Maximum tensile strain and compressive strain values observed were 0.040 pct and 0.039 pct respectively. A hypothesis was fomlated to correlate surface subsidence movements with observed underground movments. The data collected to date fits reasonably well within the formulated hypothesis.

Jan 1, 1989

By Eti Purwaningsih, Widi Astuti, Erik Prasetyo

Selective-reductive leaching of manganese from low-grade manganese ore using tannic acid as a reductant in acidic media was demonstrated by XRD, SEM-EDX characterization, and batch leaching studies at room temperature. The pH change in the liquid phase before and after leaching revealed that selectivity of manganese over iron was due to the hydrolysis of iron. The acidity in the liquid phase during leaching was dictated by two mechanisms: proton-consuming reaction (manganese oxide reduction by tannic acid) and proton-producing reaction (ferric ion reduction by tannic acid to produce ferrous ion). Based on the leaching studies, the more prevalent reaction between these two was determined by initial leaching conditions: tannic acid concentration, sulfuric acid concentration, liquid-solid ratio, temperatures, and agitation time. Kinetic studies revealed that maximum recovery was attained within 6-h agitation, which indicated a product layer diffusion process.

By Eti Purwaningsih, Widi Astuti, Erik Prasetyo

Selective-reductive leaching of manganese from low-grade manganese ore using tannic acid as a reductant in acidic media was demonstrated by XRD, SEM-EDX characterization, and batch leaching studies at room temperature. The pH change in the liquid phase before and after leaching revealed that selectivity of manganese over iron was due to the hydrolysis of iron. The acidity in the liquid phase during leaching was dictated by two mechanisms: proton-consuming reaction (manganese oxide reduction by tannic acid) and proton-producing reaction (ferric ion reduction by tannic acid to produce ferrous ion). Based on the leaching studies, the more prevalent reaction between these two was determined by initial leaching conditions: tannic acid concentration, sulfuric acid concentration, liquid-solid ratio, temperatures, and agitation time. Kinetic studies revealed that maximum recovery was attained within 6-h agitation, which indicated a product layer diffusion process.

By John H. Soule

The Torpedo Copper mine in the Organ Mining District, Dona Ana County, N. Mex., was discovered In 1899. Production was begun immediately and continued until 1907. Since 1907 very little ore has been produced, although Many individuals and companies have been interested in the property at one time or another. Approximately 6,621 feet of diamond-core had been completed on the property before 1949. The results from some of this drilling were unsatisfactory because of the poor core recovery. In addition to its investigation of the Torpedo ore deposits, attention was given by the Bureau of Mines to obtaining better core recovery through the use of special equipment and techniques. This project was begun October 3, 1949, and was completed April 30, 1950. Four diamond-drill holes totaling 2,140.5 feet, which includes 18.2 feet of overlap in a deflected hole, were drilled. All drilling was done with a Government-owned hydraulic-feed drill with some special rods and core barrels, in addition to the usual equipment. The over-all core recovery was 89.5 percent. Omitting the drilling in overburden where little or no core was desired, the recovery was 94.6 percent. Core recovery in the ore zones averaged 95.2 percent. This paper describes the location, the general features of the area, the geology, the Bureau of Mines procedures, and the results attained by these procedures.

Jan 1, 1952

By A. G. Yapo, T. W. Camm

"All-in sustaining cost is a metric used by mining companies to reflect the cost of gold mining in a consistent format useful to both investors and mining professionals. Cost reporting focused on the direct cost of mining and processing ore was summarized in the non-GAAP cash cost developed by the Gold Institute in 1996. In 2013, a group of mining companies, working with the World Gold Council, developed a more inclusive approach to reporting costs designed to solve the dilemma of showing a more comprehensive reflection of recurring costs involved in producing gold, without discouraging investors. INTRODUCTION Mining today plays a key role in the development of our civilization as a source of essential raw material and provider of essential fuels, producer of jobs, and a factor in support of the international balance of monetary payment (Camm, 2014). Professionals in mining locate, develop, design and manage ore deposits in an environmentally safe and profitable manner. As mineral deposits become increasingly scarce, new challenges face the industry. A current trend is to an increased emphasis on underground mining techniques for deeper deposits. Operations are safer today than before as companies understand better their work environment and the importance of mining responsibly. A continual challenge for the industry is accurately reflecting the costs and selling price of ore. An enduring characteristic of mining is the situation where the market typically determines the price of a commodity; the main control a company has on the bottom line is to control the cost of production. An attempt to bring light and clarity on the cost of their business will give a better idea to investors on the true profitability of the mining business. Gold producers face this struggle to accurately reflect the cost of production while also seeking to attract the interest of the investment community (Hill, 2013). In order to have a consistent format to report on their production costs, leading gold producers through their alliance inside the World Gold Council (WGC), worked on the adoption of a new cost framework: the All-in Sustaining Cost (AISC) and All-in Cost (AIC). Since 1996, the traditional cash cost reporting has focused only on the mining and processing costs incurred in mining an ounce of gold, which included the costs of goods sold (labor, energy, and consumables costs) and royalties (Table 1). But cash cost reporting ignores many important aspects, like sustaining capital, general and administrative expenses, and site rehabilitation at the end of the mine life (Whelan, 2013). The cash cost was used to attract many investors into the business. In fact the high gross margin (sales minus cash costs) has been promoted the past decades by the industry instead of the net or operating margin. As a result, even when the gold price was high, nearly $1900 per ounce in August 2011, gold producers were not reporting excessive profits in their cash flow / income statements, to the disappointment and incomprehension of investors (Milstead, 2014). The truth was simply that the other costs omitted in the traditional cash cost were reducing the apparent profits."

Jan 1, 2017

By Manqiu Xu, Joe Holmes, Peter Wells, Peter Langlois, Germain Labonté, Jim Barrett

"The flowsheet for the Voisey’s Bay mill had to meet the challenge of processing an ore containing high pentlandite and chalcopyrite values in a largely pyrrhotite/troilite matrix. In the 1994-97 period, circuit development focused on making a high-grade copper concentrate and a relatively low-grade nickel concentrate. However, in 1998 a circuit with copper concentrate, high-grade nickel concentrate and a Ni/Cu middlings concentrate was specified. Following a three year project delay, work resumed on the flowsheet in 2001, and the target for the overall grade of the nickel concentrate was raised from 14% to 20% nickel. To achieve this target triethylamine tetramine (TETA) and sulfite pyrrhotite depressants were used in an all lime circuit. It later became evident that, with appropriate selection of collector and adjustment of the circuit by the addition of a scavenger on the scavenger cleaner, it would be possible to approach the grade of concentrate required without the use of pyrrhotite depressants. The recycle of water and the contained thiosalts was also proven to be instrumental in raising the grade.Construction and commissioning of the mill were fast-tracked with start-up of the mill in September 2005 some six months ahead of the original schedule. Ramp-up of both throughput and metallurgy was faster than any other recent nickel installations with tonnage being limited mainly by concentrate dewatering due to the higher than initially planned ore grades.INTRODUCTIONNickel was discovered in the vicinity of Voisey’s Bay by Chislett and Verbiski working for Diamond Field Resources in 1993 and the Ovoid deposit was delineated in the winter of 1994/95. By the end of 1995 the Ovoid had been well explored and at that time was thought to have a reserve of at least 30 million tonnes with an average grade of 2.83% Ni and 2.0% Cu. Drilling to the east of the Ovoid had indicated the presence of significant mineralization. In June of 1995, Inco Limited bought a 25% share in the Voisey’s Bay Nickel Company (VBNC) which was a subsidiary holding company set up by Diamond Fields. Inco also bought 8% of Diamond Fields and negotiated the right to sell all the nickel produced from VBNC for twenty years as part of this agreement. In April 1996, Inco bought the 75% of VBNC shares that it did not own."

Jan 1, 2007

By R. L. Virta

Four companies mined ball call in four states in 2009, H.C. Spinks Clay Co. Inc. (owned by Lhoist Group), Kentucky-Tennessee Clay Co. (owned by Imerys Group), Old Hickory Clay Co. and Unimin Corp. Production, on the basis of preliminary data, was 820 kt (904,000 st) with an estimated value of $39.4 million. That was a 15-percent decrease in tonnage from 967 Mt (1.1 mil-lion st) with a value of $44.3 million that was produced in 2008. Tennessee was the top producing state with 59 percent of domestic production, followed by Texas, Mississippi and Kentucky. About 71 percent of production was airfloat, 18 perc

Jun 1, 2010

By R. T. Jones

The largest known platinum group metal (PGM) deposit in the world is the Bushveld Complex in South Africa, with the Great Dyke in Zimbabwe also being one of the biggest. It is therefore not surprising that the majority (just over 5 million troy ounces or 156 metric tons per annum) of the world's platinum is produced in Southern Africa. Primary smelting of ore concentrates is carried out in that region by five companies, namely Anglo Platinum, Impala Platinum, Lonmin Platinum, Northam Platinum, all of South Africa, and Makwiro Platinum in Zimbabwe. The only other primary smelter of platinum group metals is Stillwater Mining of Montana, USA, although very significant quantities of PGMs are produced as co-products by Norilsk Nickel of Russia. Smaller (but still significant) quantities of PGMs are produced by Falconbridge and Inco of Canada, also as co-products from nickel sulphide smelting. There are many similarities between PGM smelting and nickel sulphide smelting, and the range of technologies in use includes six-in-line rectangular electric furnaces, three-electrode circular AC furnaces, Peirce-Smith converters, and Anglo's ACP (based on Ausmelt technology). PGMs are also recovered from residue materials using DC arc furnace technology.

Jan 1, 2005

By Z. Botha

Sheryl Sandberg, the COO of Facebook, published a book titled 'Lean In', where she invites women to sit at the table. In summary, to 'sit at the table' entails not only embracing opportunity, but to actively seek out opportunities in leadership positions. Sandberg points out that, unfortunately, apart from institutional obstacles, a woman's own perceived limitations have a negative impact on her leadership ambitions. To create an environment where diversity will flourish, where everyone has a seat at the table and everyone has a voice, safety must be established first. To establish safety within a diverse team, there is power in relationships and connections. This study will first and foremost review theories in literature as to why diversity and inclusion are so important and the value that diversity brings to our industry. The study also recommends a few focus areas for improving diversity and inclusion in the industry.

Sep 1, 2022

By W. R. Reed, G. W. Luxbacher

As directed by the MINER act of 2006, the NIOSH Office of Mine Health & Safety Research (OMSHR) has annually awarded contracts to enhance mine safety and health. OMSHR has a history of research that focuses on both respirable coal mine dust and respirable crystalline silica (or quartz) dust, and contracts have been awarded since 2010 in support of our intramural research efforts. In 2018, a National Academies of Science consensus study report recommended expansion of respirable dust research. As a result, beginning in 2018 through 2021, eighteen contracts were awarded focusing on this area. These contracts can be grouped in three topic areas: characterization of coal/dust, development of real time monitors, and improvement of respirable dust controls. This paper summarizes the outcomes of completed contracts and the progress of current contracts.

Mar 2, 2022

By Brian Danyliw

"Dust control is an increasingly important consideration for all mining operations from a health, safety, environmental and maintenance perspective. Modern mining operations incorporate a variety of mechanical dust control techniques into design however in many cases these engineered systems are unable to meet desired fugitive dust level targets. In these cases a variety of chemical dust suppression options are available to operators to assist in meeting their targets. This paper provides an overview of available chemistries, discussion of application techniques and equipment requirements and available performance monitoring technologies. This paper will also include a number of case histories discussing the treatment approach chosen, challenges encountered, chemical feed, storage and application equipment, monitoring techniques employed and results achieved.INTRODUCTIONDust FundamentalsFugitive dust by definition is an aerosol consisting of particulate matter suspended in a gaseous medium. Aerosols can include suspensions of particulate (solids) or sprays (liquids) or a mixture of both. Of particular concern from an occupational health and safety perspective are aerosols of particulate matter due to their involvement in classical occupations lung diseases such as silicosis, poisoning through chronic exposure to compounds such as lead and beryllium and expected involvement in more modern identified conditions such as cancer, asthma, and a host of other respiratory and non-respiratory conditions which may be caused or influenced through exposure to dust.According to the ""Glossary of Atmospheric Chemistry Terms"" (IUPAC, 1990), ""Dust: Small, dry, solid particles projected into the air by natural forces, such as wind, volcanic eruption, and by mechanical or man-made processes such as crushing, grinding, milling, drilling, demolition, shoveling, conveying, screening, bagging, and sweeping. Dust particles are usually in the size range from about 1 to 100 µm in diameter, and they settle slowly under the influence of gravity."" It should be noted that the behavior of particulates with respect to settling rate in air is a function of particle mass and shape and therefore the geometric size of the particle can be misleading. Occupational hygienists utilize the concept of particle aerodynamic diameter as a more representative reflection of particle size. Particle aerodynamic diameter, is defined as ""the diameter of a hypothetical sphere of density 1 g/cm3 having the same terminal settling velocity in calm air as the particle in question, regardless of its geometric size, shape and true density."" The expression of particle size as aerodynamic diameter allows for a more consistent understanding of particle behavior both from a settling perspective as well as from the perspective of how dust particles will behave in the respiratory tract. Figure 1 illustrates settling rates for particles of various aerodynamic diameters. The relationship between particle size and settling rate is important for understanding what size of particles must be addressed by dust control strategies as well as what particle sizes represent the most danger from an exposure and occupational health perspective."

Jan 1, 2015

By Michael Murphy, Gamal Rashed, Brent Slaker

Many underground stone mines in the United States operate on multiple mining levels. The effects of interburden thickness, pillar offset between mining levels at various depths of cover, and in situ stress conditions are poorly understood. Pillar offset is the degree to which pillars are not columnized or stacked. In this study, calibrated numerical models are used to examine limestone pillar stability in these conditions. Also, the critical interburden thickness required to minimize the interaction between mining levels is explored. The model results show that there is interaction between numerous factors that control the stability of stone pillars in multiple-level conditions. The highest degree of local pillar instability occurs when pillar overlap ranges between 10 and 70 percent. The highest degree of stability occurs when pillars are stacked.

Jan 1, 2023

By Adams F. C, Ridley K. L

Economic conditions after WorId War II made the recovery of Australian sources of sulphur one of considerable national importance. From 1947 to 1949 an investigation was made of recirculation techniques to produce acid plant grade gas from the Dwight-Lloyd down-draught sintering plant.During 1949 it appeared feasible to produce a gas of suitable 802 concentration and a decision was made to construct a gas purification train and a 150 tons/day contact acid plant. However, a number of difficulties remained in the production of the gases for sulphuric acid manufacture and as a result of research conducted to overcome these troubles the continuous up-draught sintering process was developed.The principal difficulties were:(a:) The down-draught sintering practice, as developed, produced an unusually high metallic lead precipitation in the windboxes. The disposal of this lead interrupted sintering operations and the delivery of gas to the acid plant.(b) The production capacity of the existing sintering plant was fully extended and the adoption of recirculation of gases, in an endeavour to satisfy acid plant requirements, would probably reduce the plant production capacity.(c) The prevailing high temperature of water available for purification train cooling required a higher than...

Jan 1, 1956

By Axel Pankewitz, Andrew Smith, Mathias Stender, Christian Behrens

"Particle size measurement is one of the most important factors in obtaining peak performance of the mineral processing plant in order to ensure efficient milling and flotation circuit operation. Off-line particle distribution analysis technologies only allow an infrequent check of the ore slurry size and hence do not allow for timely process monitoring or intervention. Most existing on-line particle size analysers suffer from a variety of disabilities such as poor statistics, non-representative sampling or mechanically complex setup. This paper will describe an Ultrasonic Extinction based method which overcomes many limitations of existing online analysers and has proven its performance for mineral applications over many years. Installation examples will be given. Since new technologies usually raise e questions about comparability and agreement to common particle size analytical methods e.g. sieving or laser diffraction analysis, extensive studies were performed comparing these different technologies to quantify the quality of results as well as its mathematical robustness."

Jan 1, 2014

By J. B. Platt

Many utility fuel choices 1990-95 defied expectations, with utility decisions and coal market developments ever more closely linked. The Central Appalachian coal boom never occurred; clean-enough coal was developed in the hard-hit Midwest; Colorado-Utah coal surged; Pittsburgh seam production strengthened; utilities embraced Powder River Basin coal; and emission allowance prices collapsed. Competition drove productivity gains, but the future is not a simple repeat. Phase 2 brings fewer viable compliance options. Mega-railroad pricing has become a key risk factor -- will this be countermanded by merging utilities and power market competition? Revenue losses from vintage contracts are problematic. Uncertainty also plagues natural gas, in spite of unanimity across major forecasts, since recent experience has been so heavily influenced by the gas bubble.

Feb 24, 1997