Search Documents

By Peter Zhang

The immediate roof at the test site consisted of laminated clay shale that is likely to be susceptible to weathering. With seasonal dry-wet cycles in the mine ventilation air, the roof in the intake air would deteriorate and lose integrity over time. In many instances, the weathering-prone roof would gradually scale off piece by piece between bolts and over the entry corners. In some long-term entries, roof weathering could develop up to 2-3 ft deep with columns of bolted roof hanging under the upper intact roof. If wire mesh is used, the roof bags down and reduces the entry height, and the weight of the bagged roof tends to pull the bolts out and poses a safety hazard. An effective measure is always sought to support this type of weak roof that is sensitive to moisture degradation. One solution is to seal the roof shortly after entry development to prevent moisture penetration so that roof integrity can be maintained for the long term. In this application, a polymer-based sealing material was tested in the Rockspring mine for weathering protection and reinforcement. The material is a one-component polymer powder for spray application onto the roof and rib. The sealant material is mixed with water in the spraying nozzle to apply to the roof and rib as a paste. The product sets within 5-10 minutes and forms a membrane as thin as about 1/8-in. The membrane will quickly develop tensile and bonding strength within minutes and completely cure within a few days. Through sealing, bonding and lateral reinforcement, the integrity of the weak roof can be maintained. The material has been tried in a long-term evaluation over several months in a set of main entries in the Rockspring mine owned and operated by Rockspring Development, Inc., affiliate of Foundation Coal. Preliminary evaluation has shown that the material is an effective and economical solution to ensuring the long-term stability of weathering-prone roof.

Jan 1, 2009

By K. Kawakami

In Japan, pile foundations have been used extensively for buildings, bridges and port facilities. A large number of steel pipe piles were first used in the 1960's and the amount of steel used in foundations increased by 1973 to one million tons. This report describes current practice in the actual use of large diameter and long steel pipe piles in Japan, related to their performance: including consideration of pile size, hammer types used for driving the results of field tests measuring stress occurring in the piles and the driving formulae currently being used in practice in Japan.

Jan 1, 2010

By P. Schilizzi, A. Jarosz, M. Karmis

This paper is concerned with subsidence prediction methods and in particular with two techniques, one based on profile functions and the other on influence functions. Profile function methods provide a tool for a fast calculation of subsidence on a line across a mine panel. Influence function methods, on the other hand, allow for a more detailed calculation of ground movements, in any mode and at any depth, on a grid or at any specific point. In more detail, the hyperbolic tangent profile function, as developed by VPI&SU from field data pertaining to the eastern U.S. coalfields, and an influence function method currently being adapted for the same region, are presented and discussed. The applicability, advantages and limitations of these techniques are examined and comparisons are presented with field measurements. Computer software developed for the application of these prediction methods, for two widely used personal computer systems, are also discussed and a number of examples are presented demonstrating the potential of such programs.

Jan 1, 1986

By William R. Yernberg

The early part of the decade was marked by world-wide problems and economic difficulties. In 1980, President Jimmy Carter ordered the failed military mission to rescue hostages in the U.S. Embassy in Iran, Mt. Saint Helens, WA erupted killing 60 people and the Soviets and Mujaheddin guerrillas clashed in Afghanistan after the Soviet invasion. Later in the year, Ronald Reagan was elected president, defeating Carter. The first launch of a space shuttle (Columbia) occurred in 1981. Also in 1981, the first IBM-PC’s begin to roll off the lines. In 1982, Argentina invaded the Falkland Islands and Mexico’s economy was in collapse. In 1980, the U.S. unemployment rate stood at 7.1 percent, and by 1982 the rate increased to 9.7 percent. 1980 marked SME’s first full year in its new office building in Littleton, CO. The new facility was dedicated in November 1979. Claude L. Crowley was executive director of SME in 1980 and remained in that position throughout the decade. SME’s membership stood at about 26,000 throughout this period (1980-1982).

Jan 1, 2007

By J. Andrew Cornier, Mike Cooper

"Upon successful completion of the AG/SAG Mill project (Cooper et al., 2001) the Brunswick Mine concentrator was configured with single line processing through the AG/SAG mill, followed by two parallel ball mill and flotation circuits. The Stage Grinding project was undertaken to utilize a pre-flotation stage on the AG/SAG mill primary cyclone overflow and simplify the flowsheet by consolidating the two ball mill and flotation circuits, resulting in single line processing fi-om AG/SAG mill to final concentrate. Concurrently, the reclaim water supply capacity was increased to enable flotation cleaning at lower percent solids.Benefits from the Stage Grinding project include revenue enhancement from increased zinc grade and recovery combined with additional lead recovery. Further benefits included a reduction in the number of process pumps, reduction in loss associated with spillage to sumps and process simplification through efficient use of equipment layout.The Stage Grinding project was implemented in six phases over a period of seven months in 2000. Each phase was commissioned during scheduled concentrator shopdays with minimal additional downtime required. One year after project approval the Stage Grinding project was completed at a total cost of $1 1.8 million.INTRODUCTIONThe Noranda Inc. Brunswick Mine, located near Bathurst, New Brunswick, is one of the world’s largest leadzinc mines. Milling of ore began in 1964 from the No. 12 orebody, with an expansion in 1966 to accommodate ore fkom the No. 6 open pit located several kilometers away. In 1980 the pit was exhausted and the concentrator rationalized to accept a design feed rate of 10,500 tomes per day from the No. 12 mine. In excess of 100 million tomes have been milled to date, representing over three-quarters of the known reserve. The concentrator employs differential froth flotation to produce lead, zinc, copper and leauzinc bulk concentrates. The ore is massive sulphide, with approximately 20% valuable minerals, 60% pyrite and 20% silicates."

Jan 1, 2002

By L. H. Duschak, C. N. Schuette

In the years 1850 to 1923, the United States produced 2,426,000 flasks- (73,600 metric tons) of quicksilver worth $120,500,000. California yielded 2,195,000 flasks of this total; the remainder came from Texas, Oregon, Nevada, and A.rizona. Most of this metal has been extracted from low-grade ores, those containing less than 0.5 per cent mercury or 10 pounds per ton. The finished product or " virgin metal" is made at the mine and shipped in flasks. Quicksilver is unique in being the only metal that is liquid at ordinary temperature. Because of this and other physical and chemical properties, it is perhaps more indispensable to industry than any other metal. On the other hand, the quicksilver industry of the world is of vanishing significance" when compared to the major mineral industries with respect to quantity and value of product, capital invested, or the number of men employed. The peculiar value of quicksilver is due to the fact that in some of its applications no substitute is available and in others the substitutes would be unsatisfactory or extremely expensive. Scarcely a branch of science or industry fails to make some use of mercury or its compounds. As a detonator for explosives, mercury fulminate holds first place and in safety and reliability could be replaced only by the highly expensive silver fulminate.t vThrough its use in detonators and in the metallurgy of the precious metals quicksilver is of special importance to mining. In medicine,in the manufacture of electrical apparatus, the production of pigments and antifouling paints, and the general field of experimental science quicksilver is equally indispensable.

Jan 1, 1925

By Duberney Hincapie-Ladino

No presente trabalho analisou-se a influência de diferentes microestruturas obtidas através de tratamentos térmicos, sobre a resistência à corrosão de um aço microligado, na solução A segundo a norma NACE TM0284-11. Foi utilizada chapa de um aço destinado à conformação de tubo API 5L X65 para confeccionar as amostras. Algumas destas foram submetidas a tratamentos térmicos (Temperado, Temperado seguido de revenimento, esferoidização) e o restante foi utilizado tal como recebido. Os materiais foram submetidos a ensaios de polarização linear, num eletrólito composto por 0,5% ácido acético e 5% cloreto de sódio (solução A, NACE TM0284-11) fazendo-se purga com N2 e injeções de H2S. Foram realizados exames em microscópio óptico. Os valores de resistência de polarização mostraram que a ordem decrescente de resistência à corrosão de acordo com o tratamento térmico foi: (Esferoidizada) > (Tal Como Recebido) > (Temperada, Temperada e Revenida). Tal fato pode ser explicado pela quantidade de interfaces presentes em cada microestrutura (cementita globulizada em matriz ferrítica; ferrita com perlita; martensita e martensita revenida), sendo que quanto menor a área de interfaces, maior o valor para resistência à corrosão.

Aug 7, 2018

By Richard Manrique

"La implementación del proyecto de modernización de la fundición de cobre de Southern Peru Copper Corporation requiere cambiar la metodología de funcionamiento de los sopladores para la etapa de conversión. En este sentido, el presente texto señala los aspectos del Sistema de control maestro de reparto de carga implementado en la Fundición de Ilo con excelentes resultados, logrando mejorar el rendimiento de los equipos con una antigüedad de mas de 30 años e invirtiendo tan solo en nuevos controladores en una etapa ligada directamente a la línea de producción. Mantener la variable primaria presión en la red de sopladores, compartiendoóptimamente la carga entre los sopladores en la red, mientras que, se minimiza el riesgo de surge, consumo de energía y los disturbios en el arranque y el paro de sopladores individuales, el sistema deberá ser lo suficientemente flexible que no deberá de perturbarse ante la salida frecuente de los convertidores, es decir deberá de mantener las presiones y flujos a la descarga del manifold ante las variaciones en el consumo de aire todo esto con un mínimo de venteos al ambiente."

Sep 19, 2006

By Monger N. R

Factors leading to the decision to use Joy Continuous Miners for pillar extraction in the Burwood Colliery are outlined. A detailed description is given of the Joy 1-CM-2 Continuous Miner, including the power supply to the machine, and the method of cutting coalfrom a face. Modifications found necessary in practice are dealt with.The Joy 10 S.C. shuttle car used in conjunction with the Miner, and alterations made to this unit, are then described, together with Ancillary units for the whole installation such as transformers, motor generator set, air compressor,_ cables for power supply and water supply for dust suppression.Special arrangements were necessary to transport the Miner and Shuttle Cars through the tunnel to the Victoria Tunnel seam, and the method of overcoming the transport difficulties is discussed. Manning of the Continuous Miner unit, and final preparation andsubsequent working of the pillars is outlined. Special attention must be given to maintenance of the machines.It is concluded that the combination of Joy Continuous Miner and Shuttle Car is an excellent method for removing pillars in the Burwood Colliery.INTRODUCTIONThis paper deals with the Burwood Colliery in the RH.P. Group in which some units are engaged in the mechanical extraction of pillars with Joy Continuous Miners.In 1941, an amendment to the Coal Mines Regulation Act of N.S.W. forbade the extraction of pillars by mechanical means unless with the express permission of the Minister for Mines. As this permission was not forthcoming, no mechanical extraction of pillars took place in Australia until 1954 As it was doubtful during most of this period whether mechanical extraction would ever come about, coal generally was won with a view to maximum extraction in the first workings, thus giving rise to centre gannon bord panels and 45° angle cut throughs as shown in Fig. 1.

Jan 1, 1957

By Michael Mann

Two house trailers and a modem modular house, all pillar-supported with cantilevered perimeters, were monitored for structural response to vibrations from surface coal mine blasts. Due to the large blast site distances, peak particle velocities measured in the ground beside the houses did not exceed 0.32 ips, and airblasts did not exceed 106 dB. However, the structures responded significantly to the ground vibrations, with maximum high-comer amplification factors as high as 8.5 in the horizontal directions. Vertical structural responses were as high as 10 times the vertical peak particle velocities in the ground, but appeared to be driven more by horizontal ground motions. No measurable airblast responses were observed. The natural frequencies of the structures ranged from 5 to 10 Hz.

Jan 1, 2000

By Liming Yuan, Wei Tang, RICHARD THOMAS, JOHN SOLES, DAVOOD BAHRAMI

Mine equipment fires remain as one of the most concerning safety issues in the mining industry, and most equipment fires were caused by hot surface ignitions. Detailed experimental investigations were conducted at the National Institute for Occupational Safety and Health’s (NIOSH) Pittsburgh Mining Research Division on hot surface ignition of liquid fuels under ventilation in a mining environment. Three types of metal surface materials (stainless steel, cast iron and carbon steel), three types of liquids (diesel fuel, hydraulic fluid and engine oil) and four air ventilation speeds (0, 0.5, 1.5 and 3 m/s) were used to study the hot surface ignition probability under these conditions. Visual observation and thermocouples attached on the metal surface were used to indicate the hot surface ignition from the measured temperatures. Results show that the type of metal has a noticeable effect on the hot surface ignition, while ventilation speed has a mixed influence on ignition. Different types of liquid fuels also show different ranges of ignition temperatures. Results from this work can be used to help understand equipment mine fires and develop mitigation strategies.

Oct 1, 2022

By Mark S. Sanders

This report presents recommended visibility requirements for continuous miner, shuttle car and scoop operations and details the methodology used to generate them. A task analytic approach was used to define information requirements and visual features which served as sources of information. Information requirements were prioritized and the location of visual features determined. From this analysis, visual attention locations, containing one or more important visual features, were identified. A total of 71 locations-were identified for continuous miners, 54 for shuttle-cars and 54 for scoops. A procedure was developed for assessing whether operators in existing machines could be expected to see the visual attention locations. The procedure makes use of a Human Eye Reference Measurement Instrument (HERMI) designed for this project and an outside-in photographic procedure for documenting compliance with the recommendations. A sample of continuous miners, shuttle cars, and scoops were used to test the procedure. Results are presented in the report.

Jan 1, 1981

CONTENTSSummary.Introduction.Location and Geology.Historical and Exploitation.Part 1. Washability Characteristics of the Liddell.Seam.Foybrook Open Cut, Top Bench.Sampling.Size and Ash Distribution.Washability Data.Washery Separations.Part 2. Washability Characteristics of the LiddellSeam.Foybrook Open Cut, Bottom Bench.Sampling.Size and Ash Distribution.Washability Data.Washery Separations.Acknowledgments.References.INTRODUCTIONThe washability characteristics, size-range and chemical analyses of the screening from the Liddell Seam are matters of growing interest in view of the increased exploitation of this seam over the last few years, and also since the Newdell Coal preparation plant of the New South Wales Mining Company Proprietary Limited, utilizing magnetite heavy media separation, commenced...

Jan 1, 1954

By D FitzGerald, S Jakica, R Paterson, J Silic

A new 2.5D airborne electromagnetic (AEM) algorithm has been developed by Intrepid Geophysics and Jovan Silic & Associates. The advantage of 2.5D (2D geology, 3D source) AEM inversion in 3D geological mapping applications and identification of conductive drilling targets, compared to the more commonly used conductivity-depth imaging (CDI) transforms or 1D inversions, are demonstrated using examples from banded iron formations (BIFs) and other geological settings. We show emerging AEM systems are capable of providing estimates of economic rock unit thicknesses, dips and fault definition at an accuracy that mitigates the need for pattern drilling.The 2.5D inversion application used in this work and described in Silic et al (2015) is a substantially changed version of ArjunAir (Wilson, Raiche and Sugeng, 2006), a product of CSIRO/AMIRA project P223F. The changes include a new forward model algorithm and a new inversion solver. The application enables the accurate simulation of 3D source excitation for full domain models inclusive of topography, non-conforming boundaries and very high resistivity contrasts. Solution is accurate for a geoelectrical cross-section, which is relatively constant along a strike length that exceeds the AEM system footprint.The major innovation includes a new inversion solver with adaptive regularisation, which allows the incorporation of a misfit to the reference model and the model smoothness function.Memory usage has been dramatically reduced and is estimated prior to execution. For speed the software has been parallelised using Intel message passing interface (MPI) and can be used on standard computing hardware or computing clusters. Data from survey lines with lengths exceeding 100 km can be inverted on high end laptop computers.We allow flexibility in the selection of components and in the estimation of noise.AEM inversion examples are shown for surveys from BIFs, base metals (volcanogenic massive sulfides) and geological mapping projects and the results are compared with known geology and drilling. We demonstrate the much improved mapping and target definition delivered by this inversion method when compared with the other more common transforms or inversion methods used on these projects.CITATION:Paterson, R, Silic, J, FitzGerald, D and Jakica, S, 2017. High accuracy .D airborne electromagnetic inversion method for banded iron formation and other geological settings, in Proceedings Iron Ore 2017, pp 319–330 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

The placer mining industry of the West Coast region of the South Island is based largely around the production of alluvial gold, although other valuable minerals are also present. Since the first major discoveries in 1864-65, reported gold production has totalled around 264 t (8.5 Moz). During the past 10 years, annual production has totalled around 1460 kg (47,000 oz). It is anticipated that gold production over the next three years will continue at a level of 1400-1800 kg.   Annual gold production peaked during 1866 at approximately 17,170 kg (550,000 oz) and has not exceeded 100,000 oz since 1885. This reflects the ease with which gold was won from shallow, rich deposits that were present at many localities. Subsequently, there has been a general decline in the availability of this type of deposit, a trend that will continue in the future. This paper outlines the present state of placer mining in the West Coast region, gives some historical background to the industry and briefly predicts future trends.

Jan 1, 1997

By J R. Lang, J K. Mortensen

The Canadian Cordillera contains numerous classic porphyry deposits and several unusual subtypes, including the alkaline suite of porphyry Cu-Au deposits and the Tombstone magmatic suite and associated Au¦W deposits. The alkaline suite formed in collisional settings in island arcs whereas the Tombstone suite was emplaced in an active fold and thrust belt in a continental arc. In addition to different regional settings, these suites differ in the type of underlying basement, metallogeny, and the styles of mineralization. Both magmatic suites were emplaced over short intervals, probably in response to specific tectonic events. In the case of the alkaline suite, the tectonic event promoted magmatic processes suitable for the formation of porphyry Cu-Au deposits. The tectonic environment is less well constrained for the Tombstone suite, but the result was the formation of distinctive porphyry and intrusion-related Au¦W deposits.

Jan 1, 1995

By Juan M. Antorena

A pile driving and testing program was undertaken to evaluate installation procedures, assess capacity, particularly in uplift, of 360- and 460-mm (14- and 18-inch) square prestressed concrete piles and provide foundation design parameters for the New Mid-Point Bridge project in Fort Myers, Florida. Nine piles were dynamically monitored during installation, and six piles were monitored during restrike driving to evaluate pile drivability and uplift and bearing capacity including time related capacity increases due to soil "set-up". In addition, two static load tests (tension and compression) were performed to calibrated the results obtain during the dynamic testing. This paper presents descriptions of the pile driving testing program along with findings regarding pile uplift and compression capacities from the static load testing, pile capacities from dynamic testing (CAPWAP® analyses), soil-pile adhesion values, wave equation factors, soil strength vs. time dependency, foundation design (anticipated pile tip elevation) and pile driving recommendations.

Jan 1, 1995

By Sergio Neves Monteiro

This work had as its objective the characterization of a waste material, steel slag, generated from an integrated steel plant, with a view to its recycling and incorporation into red ceramics fabrication. The characterization was performed in terms of chemical composition by X-ray fluorescence (XRF), particles size distribution, X-ray diffraction (XRD), thermal analysis (DTA/TG) and scanning electron microscopy (SEM). The results indicate that the steel slag presents high amount of Ca, Fe, Mg and Si. The weight loss of the steel slag at temperatures above 800oC is associated with calcium carbonate decomposition. The coarse particle size of the steel slag is inadequate for its direct recycling into red ceramic fabrication. It is necessary to screen or to grind the waste. As a possible solution, it is suggested that screening or grinding the steel slag to a convenient particle size distribution would allow its successful industrial incorporation into red ceramics products.

Jan 1, 2006

By Sara Jane Boles

In recent years the interest in rare-earth compounds as refractory materials has exceeded the available literature on the subject. While some basic properties, such as density and melting point, of the more readily available rare-earth compounds have been reported in the literature, relatively few papers can be found that deal comprehensively and primarily with high-temperature refractory properties and applications of rare-earth oxides, carbides, sulfides, and nitrides. Therefore, this bibliography has been pre-pared for the use of the ceramic industry as a guide for locating and utilizing the scattered and frequently fragmentary information available. The term "rare earths", as applied in the literature search for this bibliography, is understood to include the following elements: cerium, dysprosium, erbium, europium, gadolinium, holmium, lanthanum, lutetium, neodymium, praseodymium, samarium, terbium, thorium, thulium, uranium, and ytterbium. (On the periodic chart, these elements appear as numbers 57 through 60, 62 through 71, 90, and 92.) It is emphasized that many of the abstracts included are from papers in which the rare-earth compound or compounds are treated along with several other ceramic materials, are mentioned only secondarily, with primary interest placed on a more commonly used refractory material, or are used as part of a mixture of materials formed experimentally and reported on in the paper. As the better known rare-earth materials, such as the oxides of uranium, thorium, and cerium, appear more frequently in the literature, they also appear more frequently in this collection. Articles abstracted include only information on the basic properties that are of interest to the refractories investigator. References to crystal lattices and related topics are generally excluded from this publication. The temperature 1,500° C. has been set arbitrarily as the lower limit for reported data on thermal properties. However, because of the scarcity of information, some reports are included in which data are limited to those obtained at lower temperatures. Many of the articles abstracted include lists of references that will be of additional assistance in pursuing specific lines of investigation.

Jan 1, 1962

By Blanchard R

In stopes of the 2000- and 2150-ft. levels in the North mine section of North Broken Hill Limited, whence a substantial proportion of the company's production is being drawn, and especially in stopes which involve the portion known as the Northern orebody, occurs it light-coloured friable porous material which represents average grade ore from which the lead and zinc minerals, and certain gangue constituents, have been largely or wholly removed by leaching. The 2000- and 2150-ft. levels lie, respectively, 1550 and 1700 ft. below extreme base of the pre-mine oxidized zone. Composition of the cellular product shows it to be supergene. The oxidation and leaching, therefore, must be assumed to have taken place since drainage of the affected areas was accomplished by mining operations.The matter is of more than passing interest, because the post-mine...

Jan 1, 1942