Search Documents

By Mavor S.

Further discussion at the Mining Institute of Scotland's general meeting held in Edinburgh, 12 February 1916, with D.W. Mowat, president, in the chair, of a paper published in Trans. Inst. Min. Engrs., 1915, vol. L, p.625 and discussed vol. L, pp.92, 433, 468, and 704 included comments by Mowat D.W. and the author's reply

Dec 1, 1916

By Rollie P. Dobyns

The K.M.A. reservoir was discovered to be oil bearing at a depth of 3,719 feet on March 11, 1931. Extensive development, however, was not begun immediately, because the discovery well had a low initial daily oil production, and market conditions for oil were unfavorable. Development of the field progressed slowly for the next 6.5 years. In the latter part of 1937, a wildcat well approximately 2 miles southwest of the discovery well was drilled on a magnetometer high and completed with an initial flowing production of 2,018 barrels of 430 A.P.I.-gravity oil in 12 hours. Rapid development of the southwestern part of the K.M.A. field was begun immediately and continued until over 700 wells were drilled and approximately 12,500 acres proved oil productive. Because of the large size of the entire K.M.A. field, this report is limited in scope to the southwestern part only, and the discussion that follows pertains to this area only. The closing date for production statistics is August 1, 1949. The K.M.A.? structure is a complex anticline having a maximum closure of 250 feet, and the K.M.A. formation is composed of sediments that grade from limestone through sandy lime and limy sand to sandstone with thin streaks of shale. Two "distinct members of the K.M.A. formation, zone I and zone II, are oil productive. Core analyses indicate the average porosity to be 16.5 percent for zone I and 16.1 percent for zone II. A relationship was established from core data, which showed the correlative permeabilities to be 42.1 millidarcys for zone I and 39.5 millidarcys for zone II, whereas the arithmetical averages of the permeabilities were 84 millidarcys for zone I and 216 millidarcys for zone II. Connate-water saturations were 17.5 percent for zone I and 20.0 percent for zone II. The porosity-saturation method, using a thickness-correction factor, was employed to calculate the volume of 168.1 million barrels of stock-tank oil initially in place in the reservoir. Analyses of the reservoir oil indicate that, although the initial reservoir pressure was 1,750 p.s.i., the original reservoir oil was saturated to only 1,300 p.s.i., at which pressure 1 barrel of stock-tank oil contained 525 cubic feet of ea~ in solution.

Jan 1, 1952

By Walter F. Atkins

Fair market value, in the legal sense , is the price which a prudent and knowledgeable buyer and a prudent and knowledgeable seller, acting without constraint or compulsion , will agree upon to exchange an asset. In the ordinary commercial or engineering usage, the term may imply simply the market value or a reasonable and equitable price. The engineer evaluator who is called upon to express an opinion about the fair market value of an asset may be able to base his estimate on the sale price of similar assets or on the market values of stock. Frequently such indicators of value are not available and the evaluator must devise other means of appraisal. Mineral resource properties may be thought of as having value by virtue of the existing or potential ability to produce at a profit. Conventional procedures permit the computation of the present value of future revenues having due regard for the time value of money and the risks attendant upon the realization of the venture. Such computations have gained wide acceptance as a basis for the estimation of fair market value.

Jan 1, 1977

By AIME AIME

THE John Fritz Gold Medal for 1929 was presented to Herbert Hoover at the Executive Mansion on April 25, at a luncheon given by Mr. Hoover to present and past members of the Board of Award, preceding medalists, and presidents and secretaries of the American societies of Civil, Mining and Metallurgical, Mechanical, and Electrical Engineers. The presentation party of forty engineers which gathered at the White House, from all parts of the United States, was made up of past presidents of the four senior national engineering societies that established the John Fritz Medal and included five men who had received the medal in previous years. These former medalists were Edward Dean Adams, J. J. Carty, J. Waldo Smith, Elmer A. Sperry and Ambrose Swasey. This medal is the highest honor bestowed by these four national engineering societies, having a membership of 60,000. It is awarded not oftener than annually for "notable scientific or industrial achievement, without restriction on account of nationality or sex." In accordance with custom, the award to Mr. Hoover was made tentatively and without announcement in October, 1927, and was formally con- firmed and announced one year later.

Jan 1, 1929

By D. A. Rhys

"The Red Bluff porphyry is a tabular 2 km long north-west trending Early Jurassic quartz diorite to monzodiorite body that intrudes a folded Triassic greywacke sequence in the lskut River area, northwestern British Columbia. The porphyry is 500 m to 800 m northeast of the Snip orebody, which is a southwest-dipping shear-vein, termed the Twin zone that contains approximately 35 tonnes of gold.The intrusion associated with the mineralization is characterized by 0.3 cm to 4 cm phenocrysts of K-feldspar in a mediumgrained plagioclase porphyritic matrix. It is overprinted by pervasive sericite + quartz ± K-feldspar ± biotite (potassic) alteration characterized by intense stockworking of quartz veins containing magnetite--hematite bands. This assemblage is cut successively by quartz veins with minor iron-oxides and pyrite, and by younger pyrite veins with phyllic envelopes. The system is gold-rich but copper-poor, with typical grades between 0.25 g/t and 0.6 g/t Au, and 0.1% and 0.2% Cu. All styles of alteration and veining have similar abundances of these metals. Where southwest- and north-east dipping shear zones are developed in the porphyry, veins of all types are sheeted and foliation parallel. These sheeted zones are interpreted to be syntectonic. Asymmetric phenocrysts, folded veins and oblique foliations developed in the 130 haulageway of the Snip mine imply oblique normally-directed shear on the southwest-dipping foliation.The adjacent Twin zone is a high-grade auriferous shear-vein system that is internally banded with: (1) carbonate-chlorite-biotite veins, with textures indicating formation at least partially by wallrock replacement, and (2) dilatant quartz-sulphide veins. Veins commonly have potassic alteration envelopes that contain biotite ± calcite ± K-feldspar. The zone is highly deformed and schistose, with numerous kinematic indicators including shear bands, asymmetric folds, rotated porphyroclasts and oblique foliations that indicate a normally-directed shear sense which is parallel to that indicated by fabrics within the porphyry.Precious and base metal veins within 2 km or 3 km of the Red Bluff porphyry are zoned. Veins and shear-veins proximal to the intrusion, such as the Twin zone, are typically enriched in gold, copper and molybdenum, and have potassic alteration envelopes dominated by biotite. Distal veins usually contain relatively abundant zinc and lead and have sericitic alteration envelopes. Structures of both types have an Early Jurassic galena Pb-Pb isotope signature.The similarities in structural fabrics and alteration histories in both the Twin zone and the porphyry, the zoning of the vein systems in the area, and the apparently concordant Early Jurassic zircon U-Pb age from the porphyry and galena Pb-Pb dates from the Twin zone and surrounding vein systems suggest that intrusion, semi-brittle deformation and a large mineralizing hydrothermal system were closely related temporally and genetically."

Jan 1, 1995

By D. Chetty

Process mineralogy forms an integral part of geometallurgy, with ore body characterisation being but one piece of the puzzle in optimising value derived from ore. This value is not only financial, but importantly speaks to sustainability from environmental and social standpoints. The reactive approach of traditional process mineralogy is increasingly being replaced by predictive methods in the geometallurgical sphere, for which mineralogical information must be timeously acquired on judiciously selected sample sets to understand ore variability and its impact on orebody processing. Such processes are not only metallurgical, but must incorporate mining and waste management protocols. Dwindling resources like water and energy also demand innovative approaches for lowering consumption and/or promoting recycling along the value chain. Addressing such challenges relies on appropriate characterisation of ore behaviour under different process regimes. Coupled with this, emerging characterisation tools are increasingly applied to understand the mineralogy of unconventionallypresented and difficult-to-process ores to meet societal and technology demands. Such tools are often accompanied by the generation of large, computationally intensive datasets, for which data management and storage are key requirements, particularly when deciphering temporal trends in ore and process variability. This paper will elaborate on these themes with examples that highlight the importance of process mineralogy throughout the minerals value chain. Keywords: Process mineralogy, ore characterisation, geometallurgy

Jan 1, 2020

By Bruce Bryant

Silver ore was discovered at Aspen in 1879, but the district did not reach full production until 1888 after lawsuits were settled and railroads furnished less expensive transportation to the outside world. The boom years were 1888-92; production declined thereafter. From the middle 1920's until 1950, the Midnight mine in the Richmond Hill district furnished most of the output in the Aspen quadrangle. Since 1950, little mining has been done at Aspen. The metals produced were silver, lead and zinc. Native silver dissolved from the sulfide ores was redeposited by waters circulating as deep as 300 m below the land surface, resulting in great secondary enrichment of many of the deposits. Over 100 million ounces of silver were produced in the Aspen quadrangle. Low-grade lead-zinc deposits remain between the old workings locally, and data available suggest that primary ore below levels mined is also of low grade. The ore occurs in the Mississippian Leadville Limestone and the lower part of the Pennsylvanian Belden Formation in sites that were made favorable for deposition by a number of stratigraphic and structural factors.

Jan 1, 1982

By E. W. Rouse

THE year 1936 has seen rehabilitation of many plants which had been closed or severely curtailed. The Steptoe smelter of the Nevada Consolidated Copper Co. has been transformed by a rearrangement of the flow of material and utilization of mechanical handling to a maximum. The Phelps Dodge Corp. reports the construction of newer and better reverberatories at the Copper Queen smelter, and of particular interest, a single high-pressure waste-heat boiler placed directly over the uptake. There has also been a complete reconstruction of the smelter at the Laurel Hill plant of the Nichols Copper Co.

Jan 1, 1937

By J. Sikamo, A. Mwanza, C. Mweemba

"The Zambian copper mining industry as we know it today had its genesis in the 1920s. Consistent private sector-driven investment in the industry over a period of over 50 years in exploration, mine development and operation, development of minerals processing facilities, building of infrastructure for pyrometallurgical and hydrometallurgical processing, with attendant support facilities, including building of whole new towns, resulted in copper production rising to a peak of 769 000 t in 1969, providingover 62 000 direct jobs. The industry was nationalized in 1973 and remained in government hands for just over 24 years. During this period, the industry experienced a serious decline in production levels, reaching the lowest level in the year 2000 when production was 250 000 t. An average of just under 2000 jobs were lost every year in the 24-year period, reaching just over 22 000 direct jobs in 2000.Following the return of Zambian politics to pluralism and liberalized economic policies, the government decided to privatize the mining industry. The process started in 1996 and by the year 2000 all the mining assets had been privatized. The new investors embarked on serious investment to upgrade the assets and to develop greenfield mining projects. Fourteen years later and after more than US$12 billion investment, production levels increased year-on-year to a peak of 763 000 t in 2013 with direct jobs reaching 90 000.This paper discusses the impact of the mining industry in Zambia on the economy in areas such as employment, support for other industries, direct contribution to the national gross domestic product (GDP), foreign exchange earnings, and social amenities. The paper also focuses on the performance of the mines during these periods vis-à-vis mineral availability, mineral grades and complexity, new technologies, and human capital. This is looked at particularly in the light of current challenges the industry is facing. Suggestions are proposed on how the industry can be nurtured to continue being a major driver for the Zambian economy and a major player in the international copper mining business."

Jan 1, 2016

By S. C. Sun

A study(1) on the sulfuric acid extraction of alumina from some Pennsylvania ferruginous clays indicated that the published electrolytic method(2)(3) seems to be more efficient than the known chemical methods (4-9) for removing iron from the leach liquor. The main disadvantages of the chemical methods are the consumption of excessive amounts of reagents and/or the precipitation of prohibitive amounts of aluminum. In the electrolytic method, iron is deposited on the mercury cathode, while aluminum is not and remains in solution. This method, however, had been handicapped by the lack of an effective and economical way to purify the contaminated mercury cathode.(7)(l0). Described herein is a scheme for cleaning the mercury cathode, and for recycling the clean mercury back into the electrolytic cell. Armed with such an apparatus, the effects of applied potential, temperature, and operation time on the electrolytic separation of iron from aluminum sulfate solutions were determined. For the sake of comparing results, a term, removability, was coined to represent the percentage of iron amalgamated per unit height of electrolyte (cm.), per unit surface area of cathode (cm.2), per unit of operation time (second).

Jan 1, 1968

By Tom Treleaven

The success of any blast is dependent on the accuracy of the blast design and the field controls used on the shot. This point cannot be over emphasized because when the geometry is not measured and/or field controls are not properly implemented, it can often have devastating effects on the final blast results. Thus drilling accuracy, tiont row burden control, explosive confinement, energy distribution, explosive selection, timing and structural geology become critical parameters in the design of successful blasts. Understanding the actual dynamics of the blast and why certain results were achieved is the fast step in optimizing a blast design. As stated by R. Frank Chiappetta, “Of all the blast monitoring systems available today, high speed videography still remains as the best stand alone instrumentation system for blast diagnostics.” Over the past years I have analyzed hundreds of blasts using either high-speed lowcams (500 frames per second) cameras or standard digital (30 frames per second). These analyses confirm, without a doubt, that shot geometry, in combination with structural geology, is the most important factor in overall blast results. Drilling accuracy is the single most important component in efficient blasting. Having equal mass associated with an equivalent energy is the basis in which blasts are designed. When drilling inaccuracy or borehole deviation occurs, not only is the energy unevenly distributed, but the basis of all design calculations becomes invalid. Over the past several years, quarry and mining operations have employed the use of boretracking measuring devices to measure borehole deviation and hole toe locations. In cases of operations using top hammer drills, it was discovered that the amount of deviation was significant and far greater than they believed they had. Set up error, improper drilling techniques and bit wear were some of the contributing factors. Through video anaysis of boretracked blasts, blast results were directly linked to drilling ..accuracy. The comparisons here took into account blast design, energy factors and hole sequencing.

Jan 1, 2000

By W. Lawrence Austin

Jan 1, 1884

By Hu Harries

WE RECENTLY completed a study for a client, who is an applicant to export gas from the Province of Alberta, on the effects of gas export on Alberta's economy. This study was part of the client's application ?before the Conservation Board, and, no doubt, some of you are familiar with it. Submissions by other applicants in earlier hearings before the Board and before the Royal Commission on Energy, as well as claims made by parties opposing export, have also brought forward a number of other opmwns regarding possible economic effects. Ali of these studies have been on a piecemeal basis. They have dealt with particular aspects of particular applications, and only indirectly and by inference with the overall question of gas ex-port. We have prepared this paper to review the overall picture and ex-amine, as far as time permits, all sides of the question. While the paper is entitled Economic Effects of Gas Export on Alberta, we felt that the area considered should in-elude northeastern British Columbia, not only because Westcoast, the first major gas export project, is essentially a northeastern B. C. project, but because this area has historically been, from the point of view of economic, if not of political, geography, part of Alberta. In this paper, when we talk of export, we mean export from the Province or, in this case, from Alberta plus northeastern B. C. Sales to other parts of Canada have exactly the same effect on the economy of this area as l1ave sales to the United States, provided, of course, they are made on equal terms.

Jan 1, 1958

By Paul M. Tyler

MUCH has been said in print, and much more that was unprintable, about burdensome controls, taxation, and multiplying restrictive, regulatory, or taxing activities of the Federal Government, but not so much has been said about ways and means whereby the Government can and does render economic assistance. Economics has been defined as the study of men earning a living, and economic assistance to industry as well as to individuals properly should take the form of helping enterprisers to help themselves rather than charity. Proposals to have the Government play Santa Claus must be examined carefully if -only to avoid undue favoritism to politically important persons and downright venality by potentially crooked public officials. Thomas Jefferson is credited with the remark that the best government is the one which governs least. Paternalism is abhorrent to most Americans.

Jan 1, 1947

By H. Foster Bain

THERE has never been a great civilized nation which did not have a mining industry; civilization cannot flourish without metal mining. Without tools we can have none of the 'industries that are the foundation of civilization and without metal mining we cannot produce the material of which tools are made. Therefore, if we have no metal mining we have no metals, no tools, no civilization. An example to illustrate this may be drawn from a recent article in the Saturday Evening Post which described the run-down condition of modern Athens. Athens is nothing but a busted mining camp! In its palmy days the Greeks so applied the leasing system to the silver mines of Laurium that the royalties, paid the expenses of government and instead of a tax bill the inhabitants received a pay check. The Persians came over to capture these mines but the Greek navy was built to defend them. When the silver mines played out, Greek civilization declined.. Our mining must continue if our civilization is to continue.

Jan 1, 1921

By H. Reimer

The rates of return on investment are examined for several major Canadian mining companies. Because we are dealing with a highly cyclical industry, subjected to widely fluctuating metal prices, rates of return are examined over a 20-year period. Conveniently, the first decade examined reflects the period when the industry enjoyed incentives to develop deposits; during the second decade, incentives were reduced and the industry became the most heavily taxed industry in Canada. The high rates of inflation since 1973 have distorted the real rates of return on investment if one considers replacement cost.

Jan 1, 1977

By Stuart St. Clair

EARLY in 1936, when the American Petroleum Institute issued -J "American Petroleum Industry," which was a survey of the current position of the petroleum industry, and its future outlook, and the figures for petroleum requirements .for 1950 and 1960 were widely publicized by the several oil journals, the impression was given that the petroleum- industry must be nearing maturity and would by 1950 have passed the high' point of its obligations to business progress in the United States.`' Let -us look at the figures which might conduce, this thought. Referring to p. 32 of the report, the total indicated crude-oil requirements in 1940 are 1,099,000,000 bbl-; for 1950, the peak, 1,109,800,000 bbl.; for 1960 a decline to 1,071,020,000 bbl. This downward trend, then established, is probably expected to continue. And this in the face of a crude production in 1935 of 993,942,000 bbl., 38,858,000 bbl.

Jan 1, 1936

By W. W. Adams

The accident-prevention record of the coal-mining industry in the United States was more favorable in 1936 than in 1935, both from the standpoint of the relative safety of the individual miner on the job and of the price in life and limb that the Nation paid for its year's supply of coal. The increase in relative safety of the individual miner was indicated by a lower death rate and a lower injury rate than in the preceding year per million man-hours of exposure to the hazards of mining; that is, per million hours of work performed by the employees. (See table 1.) A reduction in the price in life and limb that the Nation paid for a year's supply of coal was indicated by a smaller death rate and a smaller injury rate per million tons of coal produced. Thus the individual miner was a better insurance risk, as far as accidents were concerned, in 1936 than in 1935, and a ton of coal used in the homes and industries of the country represented less human suffering than in 1935. The two points of view are distinct, and both should be kept in mind when considering accidents and safety in coal mining or in other industries. More men were employed in 1936 than in 1935, and more workdays were available for the individual miner. Large gains were also made in the total number of man-shifts and man-hours worked in the industry as a whole. In number of tons of coal mined, 1936 showed large gains over 1935. Moreover, the average output of coal per man-hour worked was higher in 1936 than in 1935. All of these gains were made without lengthening the average number of hours of work per man per day.

Jan 1, 1939

By F. B. Waanders

Coal, as energy resource, possesses numerous characteristics and properties which all have an influence on its gasification behaviour. The two properties considered as critically important when evaluating a coal source for gasification is its mineral content and slagging behaviour. Research has indicated that slagging formation can be inhibited or even prevented by the addition of a fluxing agent. It is thus of great importance to understand the mineral interaction during gasification in order to select a suitable fluxing agent for the prevention of slagging and clinker formation in the gasifier. The aim of the present project is to evaluate the effect of iron as a fluxing agent and study the transformation of the mineral and added iron during gasification. A pre-determined amount of pure elemental iron (between 2wt% and 20wt%) was added to a base case coal sample in order to study the effect of the addition of iron to the coal. The transformation of the iron in conjunction with the possible iron containing minerals present in the coal was studied by means of Mössbauer analyses. Typical characterisation techniques included proximate analyses, ultimate analyses and ash composition analyses. The ash fusion temperature analyses (AFT) were used to study and predict the slagging behaviour of the iron-spiked coal samples. Even though AFT analyses only provide an average flow property, it gives a good indication of the changes that the iron addition induces on coal properties. FactSage modelling was carried out in conjunction with the Mössbauer and AFT analyses. From the proximate, ultimate and ash composition analyses it was clear that the coal used con-formed to the average characteristics measured over an extended time period. From the AFT values it was seen that an increase in the flow temperature occurred with the addition of pure elemental iron to the coal, which can be of importance for operational purposes as to raise the gasifier temperature and not to have slagging problems to occur in the gasifier. The Mössbauer data show that he-matite is the main Fe-component that forms from the pyrite originally present and from the added iron to the coal, consistent with FactSage modelling, which shows that the partial oxygen pressure determines which mineral species will form. This study opens up new possibilities when considering operational problems experienced in in-dustrial gasifiers. Successful completion of this study and a study to look at reducing conditions in the gasifier will also add to the knowledge that already exists regarding fluxing agents.

Jan 1, 2014

By Kasimcan Koruk, Julian M. Ortiz

A geological model accounting for uncertainties possesses important advantages for resource estimation. Machine learning algorithms (MLAs) employed on multivariate geochemical datasets open up ways to new methodologies for such geological models with ease in comparison to traditional geostatistical methods. This article proposes a two-step MLA with an ensemble implementation to define geological domains and their uncertainties based on geochemical data. The proposed workflow is applied hierarchically on a dataset from a porphyry copper deposit to perform binary classification that can be attributed to alteration domains.

Mar 1, 2024