Search Documents

By Heinrich Ries

I. INTRODUCTION. THE facts is presented in this paper, based chiefly on recon¬naissance made, during the summer of 1903, by myself and my assistant, Mr. R.. C. Brooks, cover practically all that portion of Texas lying east of the 99th meridian. The work was undertaken for the University of Texas Mineral Survey, and was to have been extended over the entire State, but the sudden termination of the survey prevented even the official publication of the results already obtained. Most of the mineral resources of Texas were fully treated by the First Geological Survey, but the clay-industry was tit that time little developed, so that only a few scattered notes concerning it are to be found in the Survey reports. The extensive exploitation of the clay-deposits, however, has emphasized their commercial importance, and has also made accessible many facts of exceptional interest concerning their geologic conditions. The erection of new plants for the utilization of clay-products is usually preceded by more or less prospecting, which, by reason of the scarcity of outcrops, and the geologic and topographic conditions of eastern and southeastern Texas, is often slow and difficult work. This is especially true in the Tertiary and Pleistocene areas, where the structural conditions much resemble those of the Atlantic coastal plain, the deposits being mostly lenticular in form, and surrounded by beds of sand. II. GENERAL GEOLOGY OF THE CLAY-DEPOSITS. The accompanying sketch-map, Fig. 1, shows the location of nearly all the deposits examined, their relation to the geology of the State, and the type of clay found in each. The geology is based on the published work of Hill, Cummins, Tail, Adams, Hayes and Kennedy, but the boundaries have unfortunately not been determined over the entire region covered by the map, and, in many areas, are only approximate. It will be seen that the clay-deposits range from Carboniferous to Pleistocene in age, the older deposits being found in the northwestern part of the area, while those of Cretaceous and Tertiary age lie to the east, southeast and south. The Pleistocene clays are found in part in a belt along the coast, and in part along many of the larger rivers, where they often underlie extensive terraces.

Sep 1, 1906

By Henry Kreisinger, WALTER T. RAY

In its investigation of more efficient methods for utilizing the coals and lignites in the United States, to the end that waste might be avoided, the value of low-grade coals increased, and the life of the nation's fuel resources prolonged, the technologic branch of the United States Geological Survey carried on a study of the factors involved in the manufacture and use of briquets, including the suitability of various coals for briquetting, the cheapest and most satisfactory binders, and the furnace behavior and evaporative efficiency of briquetted fuel. The investigations had their beginning in the work done at the coaltesting plant at the Louisiana Purchase Exposition, St. Louis, Mo., in 1904, and were continued at St. Louis and later at Norfolk, Va. Accounts of various tests and statements of the conclusions to be drawn from them have appeared in a number of bulletins. a In connection with the work at Norfolk, comparative steaming tests were made in stationary, marine, and locomotive boilers with run-ofmine coal and the same coal formed into briquets of two sizes. The tests in a locomotive boiler that are described in detail in this bulletin were undertaken to add cumulative evidence to work done at other places. They were made possible through the courtesy of the Seaboard Air Line Railway Company in supplying both the locomotive and the coal used. During the trials the locomotive stood on a side track in the shop yards of the railway company at Portsmonth, Va. No running tests were made.

Jan 1, 1911

Anaconda Aluminum Co. began production from a new 60,000-ton-per-year potline at Sebree, KY, which brings the total capacity of the plant to 180,000 tons per year. A strike by workers at Alcan Aluminium Corp. primary aluminum smelters at Arvida, Que., Isle Maligne, Que., and Beauharnois, Que. shut down the plants and the company announced force majeure on part of its ingot supply commitments. Kaiser Aluminum and Chemical Corp. announced plans to increase its price for primary aluminum from 60.0 cents per pound to 63.0 cents per pound effective July 1.

Jan 1, 1979

By Percy W. Bidwell

THE statisticians had defeated Germany months before she invaded Poland. With batteries of adding machines they had proved that she was suffering from serious deficiencies in critical food- stuffs and in practically all of the raw materials necessary for the conduct of modern warfare. Their calculations showed that with respect to fats, oils, wool, cotton, hides, petroleum, iron, copper and other metals, the Reich was bound to be at a great disadvantage vis-a-vis the French and British as long as the latter could keep open the lines of sea communication. The conclusion seemed obvious-"Germany can't win." The more cautious of the commentators introduced qualifications as to the length of the war and the tightness of the British and French blockade. They also made a third qualification as to the character of the struggle- whether it was to be a war of attrition or a war of movement. But since the invasion of Norway in April, there is no longer any doubt on this score. It is a war of movement-a war in which fuel, lubricants, and metals are being consumed on a scale never before seen.

Jan 1, 1940

By G. R. Hopkins

According to reports received by the Bureau of Mines, Department of Commerce, as of January 1, 1929 there were 413 completed refineries in the United States, with a total daily crude-oil capacity of 3,509,540 barrels. In addition, 14 refineries, with a potential capacity of 99,000 barrels, were being constructed. Of the completed refineries, 341, with a capacity of 3,325,890 barrels, or 95 per cent of the total capacity, were in operation; and 72, with a capacity of 183,650 barrels, or 5 per cent of the total, were shut down. The improved condition of the refining industry in 1928 was indicated in several ways; namely, in an increase in the total capacity of the completed plants, in the opening up of a few plants which were shut down during 1927, in a decrease in the number of plants dismantled, and in an increase in the number of plants under construction. The majority of the refiners have followed a steady expansion program commensurate in most cases with the increase in demand for petroleum products. Obsolete equipment has been dismantled and modern equipment has been installed, with the net result that the total capacity of the completed refineries in the United States has shown a steady increase since January 1, 1918, the date of the first Bureau of Mines survey. Between January 1, 1928, and January 1, 1929, the number of completed plants fell from 423 to 413, but their total capacity increase 259,160 barrels, or 8 per cent. This compares with an increase in runs to stills of domestic and foreign crude petroleum of 10 per cent, and of domestic crude alone of 7 per cent.

Jan 1, 1929

By AIME AIME

SCRIPTURE, statistics and imagination all were drawn upon by the speakers who acclaimed Daniel C. Jackling as recipient of the William Lawrence Saunders Gold Medal for 1930. The award was made at a special dinner at the Ritz-Carlton, in New York, on Oct. 31. Lafayette Hanchett, old friend and associate, said that if it were his task to compress the life story of Daniel Jackling into a single sentence, he could find noth¬ing so appropriate as these words from the 22nd Chapter of Proverbs, "See'st thou a man diligent in his business, he shall stand before Kings." Mr. Jackling's diligence, according to the speaker, his love for his task, have been outstanding in his career. W. S. Boyd, now ranking official in the Jackling organization, cited amazing statistics as to the quantity of copper supplied to industry by the four "porphyry". coppers that are under Mr. Jackling's immediate direc¬tion, as well as by those that, in a sense, owe their existence to the pioneer work at Utah Copper. In the aggregate- 16,000,000,000 lb. of copper having an approximate value of $2,700,000,000 have been produced from disseminated ores since 1905; and of this total 42 per cent came from Utah and the Nevada group. Newcomb Carlton, president of the Western Union Telegraph Co., long an admirer of Mr. Jackling, adroitly drew a picture of a similar occasion in some 'foreign country. He imagined Mr. Jackling being raised to the peerage and whimsically addressed him as Sir Daniel, the Right Honorable Earl of Bingham!

Jan 1, 1930

By William H. Snyer

A relatively inexpensive, very fast response photo-optic/fiberoptic system has been conceived, constructed and employed by Denver Research Institute (DRI) to measure charge breakout uniformity on the surface of a very large ANFO detonation. The new equipment and technique was coined OWL (observation without leads). Its unique design provides the ability to monitor or measure detonation velocities and/or detonation breakout characteristics without fiberoptic or any other direct contact with the explosive. This system has proven to be versatile and has been used to measure surface breakout simultaneity on large ANFO detonations, munition case breakout times and velocity of detonation (VOD).

Jan 1, 1990

The mineral Industry, following the economy as a whole, experienced little growth in 1992. However, with modernized plants, efficient workforces, and lower operating costs, the industry is well positioned to take advantage of possible improvement in the national economy during 1993. In addition to the significant 1992 events highlighted below, important events, trends, and issues within individual mineral industries are addressed in the commodity sections that follow. The value of processed materials of mineral origin is estimated to have been about $310 billion in 1992. The value of U.S. raw nonfuel minerals production in 1992 is estimated at approximately $32 billion, a 3% increase over 1991. The value of domestic minerals production has increased in all but 4 of the last 32 years.

Jan 1, 1993

By Charles Janin

The recovery of gold from sands and gravels is one of the oldest forms of mining; it antedates history and has been practiced by savage peoples. In North America the search for placer gold has been a powerful agency in the exploration and development of unknown regions and has profoundly influenced the course of our civilization. With the progress of invention, the improvements in machinery, and the availability of large capital for the conduct of great operations, the tendency in placer, as in many other branches of mining, has been toward the working of extensive but comparatively low-grade deposits. The early miner washed the rich spots in stream beds or terraces with his pan, his long tom, and his primitive sluice. Then followed the growth of hydraulic mining and the use of giants supplied with water under pressures of hundreds of pounds to the square inch that could work at a profit gravels whose gold tenor was less than 3 cents to the cubic yard. Finally came the dredge that could handle deposits lying so far below water level as to be beyond attack by other methods. Although the gold dredge was first successful on a commercial scale in New Zealand, it has reached its present strength and efficiency in this country and its development is a monument to the daring, per- severance and technical skill of the many men, mine owners and engineers who have each contributed something to the final result. The Bureau of Mines, authorized to conduct investigations for the purpose of increasing efficiency in the mineral industries, had its attention called some years ago to the need of a comprehensive report on gold dredging in the United States. The director of the bureau recognized that such a report should summarize the development of the gold dredge, should describe in detail the essential features of present-day dredges, should discuss the facts that determine whether a placer deposit can be profitably dredged, and should point out the approved methods of prospecting placer ground and of operating dredges. At the request of the director, the author undertook the preparation of such a report and has been intermittently engaged on the task for several years. This bulletin is the outcome of his labors. He hopes that it will prove of interest to designers and builders of dredges, to mining engineers, and to persons who may contemplate investing capital in placer-mining ventures.

Jan 1, 1918

By LUDWIG VOGELSTEIN

WE are indebted to Mr. Barbour for his valuable contribution to the literature on copper statistics; it is to my knowledge the only intelligent attempt to throw light on a much misunderstood subject. If I should appear to criticize some of his findings and arguments, I do not want to leave the impression that I do not appreciate the article; I think Mr. Barbour has been painstaking, and even where one might not agree with his conclusions, he has opened our eyes and stimulated us in our search for the truth.' It might be well to define the term "secondary copper" and to make a few remarks about the origin and the reasons for the variation of the supply. Mr. Barbour has touched on these points, but not sufficiently to make them clear to those not in the business.

Jan 1, 1931

By R. A. McIvor, R. Levac

"The Stobie No. 7 shaft, 14 ft diameter, double- drum skip hoist, was installed at the INCO Limited Frood Stobie Complex in 1942. Figure 1 shows the hoist layout. The hoist was originally equipped with babbitted journal bearings on the main drum shaft and pinion gears. In 1990, the hoist was modernized with a new braking system, two new 2000 hp D.C. drive motors, a thyristor armature supply and a PLC control system. The new drive motors were connected to the drive pinion gears with a gear type flexible coupling. The pinion gear journal bearings were refitted during the refit in 1990 as the existing babbitted bearings showed signs of wear. The pinion gear journal bearings had always run warm and had external cooling applied during the warm summer months. Figure 2 shows the journal bearings on the pinion shaft. The skip hoist main bull gear and two pinion gears were replaced in 1997 because of cracked bull gear spokes. New drive couplings were installed on the pinion gears and the pinion journal bearings were modified to allow some self-aligning properties to try to reduce the heating and wear on the babbitt. The modifications did not significantly reduce the heating problems and a decision was made in the spring of 1998 to convert the bearings to self-aligning, anti-friction-type bearings.The traditional roller bearings used on double helical pinion drive gears in hoist applications has always been double-row spherical roller bearings due to their high load-carrying capacity and misalignment allowances.Unlike single helical gears, double helical arrangements do not exert axial thrust on the pinion gear bearings, therefore, both bearings in the pillow blocks must float easily with any pinion displacement. Drum misalignment, thrust bearing end play and a multitude of other influences causes continuous axial displacement of the pinions when in operation. This constant displacement or “hunting” of the pinion gear to maintain its centre on bull gear often exceeds the axial clearance limits of spherical roller bearings thus resulting in a continuous sliding motion of the bearing outer rings against the housing seats. With time, the housing fit eventually wears, creating an out-of-round condition for bearing housing (maximum allowable cylindricity tolerance is IT4/2). When this happens, the pillow block housings must be replaced or re-machined to specification. Premature bearing wear and overheating will occur if a housing out-of-round condition is encountered."

Jan 1, 2001

By Mark Rebagliati, John Payne, Jim Oliver

Abstract-The Campo Morado precious-metal-bearing, volcanogenic massive sulfide deposits occur in a lower Cretaceous, bimodal, calc-alkaline volcanic sequence in a major northerly trending belt in the Guerrero Terrane in northeastern Guerrero, Mexico. During upper Cretaceous to Early Tertiary greenschist-facies regional metamorphism, the rocks were deformed strongly into a northeast-verging fold-and-thrust belt. Three later stages of weak deformation were dominated, respectively, by kink folds, broad warps, and extensional faults. Most deposits occur in the upper part of a sequence of felsic flows and heterolithic volcanoclastic rocks or at its contact with overlying chert and argillite-sandstone. The Reforma and El Rey massive sulfide deposits are on the overturned limb of a major, thrusted anticline, and the Naranjo and El Largo massive sulfide deposits are to the south on the upright limb of the same major fold. The La Lucha and San Rafael massive sulfide occurrences are in an upper plate to the southwest which was thrusted over the plate containing the Naranjo and El Largo deposits. In several of the deposits, Au, Ag, Zn, and Pb are concentrated near the stratigraphic top, and Cu is concentrated near the stratigraphic base. Major minerals are pyrite, quartz, ankerite, sphalerite, chalcopyrite, and galena. Minor minerals are tennantite-freibergite, arsenopyrite, and pyrrhotite. Gold and Ag occur in argentian gold, and Ag also occurs in tennantite-freibergite. The cumulative inferred resource of massive sulfide for the Reforma, Naranjo, El Rey, and El Largo deposits exceeds 30 Mt, with the latter two deposits incompletely delineated. Underlying pyrite-quartz stockwork zones contain chalcopyrite, chlorite, and sphalerite. Hydrothermal alteration minerals in the stratigraphic footwall are pyrite, quartz, chlorite, ferroan dolomite, and ankerite. In the stratigraphic hangingwall, hydrothermal alteration minerals are sericite, calcite-dolomite, and lesser clay minerals and quartz. The deposits belong to a low-sulfidation, volcanogenic massive sulfide system formed in a subaqueous environment, and are of the bimodal, siliciclastic type.

Jan 1, 1997

By Mark Rebagliati, John Payne, Jim Oliver

The Campo Morado precious-metal-bearing, volcanogenic massive sul?de deposits occurin a lower Cretaceous, bimodal, calc-alkaline volcanic sequence in a major northerly trending belt inthe Guerrero Terrane in northeastern Guerrero, Mexico. During upper Cretaceous to Early Tertiary greenschist-facies regional metamorphism, the rocks were deformed strongly into a northeast-verging fold-and-thrust belt. Three later stages of weak deformation were dominated, respectively, by kink folds, broad warps, and extensional faults. Most deposits occur in the upper part of a sequence of felsic ?ows and heterolithic volcanoclastic rocks or at its contact with overlying chert and argillite-sand-stone. The Reforma and El Rey massive sul?de deposits are on the overturned limb of a major, thrusted anticline, and the Naranjo and El Largo massive sul?de deposits are to the south on the upright limb of the same major fold. The La Lucha and San Rafael massive sul?de occurrences are in an upper plate to the southwest which was thrusted over the plate containing the Naranjo and El Largo deposits. In several of the deposits, Au, Ag, Zn, and Pb are concentrated near the stratigraphic top, andCu is concentrated near the stratigraphic base. Major minerals are pyrite, quartz, ankerite, sphalerite,chalcopyrite, and galena. Minor minerals are tennantite-freibergite, arsenopyrite, and pyrrhotite. Goldand Ag occur in argentian gold, and Ag also occurs in tennantite-freibergite. The cumulative inferred resource of massive sul?de for the Reforma, Naranjo, El Rey, and El Largo deposits exceeds 30 Mt, with the latter two deposits incompletely delineated. Underlying pyrite-quartz stockwork zones contain chalcopyrite, chlorite, and sphalerite. Hydrothermal alteration minerals in the stratigraphic foot-wall are pyrite, quartz, chlorite, ferroan dolomite, and ankerite. In the stratigraphic hangingwall, hydrothermal alteration minerals are sericite, calcite-dolomite, and lesser clay minerals and quartz. The deposits belong to a low-sul?dation, volcanogenic massive sul?de system formed in a subaqueous environment, and are of the bimodal, siliciclastic type.

Jan 1, 1997

By B. R. Mohal, S. Chander

"A new technique to determine wettability of powders is presented in this paper. In this technique the times for immersion of individual particles from air into liquids, defined as imbibition times, are measured. Through the measurements of imbibition times for a large number of particles, it is possible to determine homogeneity/heterogeneity of a powder sample with regard to its wetting behavior. Quartz particles give a very narrow distribution of imbibition times showing a homogeneous wetting surface whereas coal particles give a broad distribution indicative of the heterogeneous nature of its surface. The imbibition time measurement technique is considered to have certain advantages over other methods to determine wettability of powders in surfactant solutions. In this study we have also compared the imbibition times with the wetting rate mea¬surements obtained by a modified Walker test.INTRODUCTIONSeveral methods are available for determining wetting characteristics of sol¬ids. Each of the methods has been used in the past to obtain very valuable information for comparing wetting behavior of various solids in a given liquid or for comparing the wetting behavior of several liquids for a given solid. Each method measures a somewhat different aspect of wetting and therefore quantitative correlations between techniques have been difficult. A general approach is to use a method in which close similarity between the technique and the application (where results of wetting measurements are to be used) can be maintained. The objective of this investigation was to develop a method which could be used to determine the wetting characteristics of single particles in surfactant solutions. Wetting of individual particles is of importance in cap¬ture of dust particles by sprays of surfactant solutions.METHODS FOR DETERMINING WETTING — A BRIEF REVIEWThe various methods available for measuring wetting characteristics of solids include: contact angle, immersion/sink time, bubble pick-up, induction time, capillary rise, and displacement method measurements. Some of the methods are briefly reviewed in the paragraphs that follow."

Mar 1, 1989

By J. E. Hawley, Y. Rimsaite, T. V. Lord

"IntroductionIN THE COURSE of. a spectrographic investigation of the platinum metal .content of various minerals in sulphide ores, the use of • fire-assay beads dissolved in gold-amalgam ( 1) was found suitable for the quantitative determination of palladium and platinum. Later work on platinum and bismuth-rich beads showed however, that these could not always be readily mixed uniformly in the amalgam. Accordingly another technique was sought which would allow the simultaneous determination of gold, silver, palladium, platinum, rhodium, and bismuth, the last .a common contaminant in fire-assay beads. The method evolved, which consists of dissolving fire-assay •beads in .lead, resembles in several respects the method of Scobie (2) in which silver was used. It has equally good sensitivity arid reproducibility, and allows the determination of silver as well as the other metals mentioned. The 'mutua1 standard' method of calculation (3a) is used to determine actual quantities present. This method has been applied to sulphide and arsenide minerals and •ores• of nickeliferous and non-nickelferous deposits• of both pre-and post Cambrian age, and, following a suggestion by Dr. G. S. Hume and the late Dr. H. V. Ellsworth, Geological Survey of Canada, has also been used for a peculiarly rich platiniferous uranium oxide ore from the Nicholson property, Lake Athakaska, Sask. More recently, the method has been .tested for the determination also of iridium and ruthenium and results indicate it may be applied, as• well to osmium."

Jan 1, 1953

By George J. Young

DR . JOHN A . CHURCH, in his treatise on the Comstock Locle 1 gave a full and clear account of the conditions of the mine during the period of greatest activity. The difficulties in the way of deep mining at that time were excessive water and high temperature. The drainage of the mines taxed the financial resources of the mining companies, and the high temperatures restricted the capacity of the miners for underground labor. In spite of these difficulties exploratory work was continued until the financial burden of removing the water became too great. The companies then restricted the work to the upper levels. The years 1883 to 1886 marked the period of cessation of deep mining. For 12 years thereafter mining was confined to the levels above the Sutro tunnel; and, while the question of drainage was more or less agitated, nothing of importance was done until the formation of the Comstock Pumping Association in 1898. Since that time successive levels have been drained until, at present, on the north-end mines, a depth of 700 ft. below the Sutro-tunnel level has been reached. Mining is now carried on in the Ophir mine from the 1,700- to the 2,200-ft. levels, and a winze is being sunk to make connection with the 2,300-ft. level (the 2,450 ft. of the C. & C. shaft). In 1903-the Ward Shaft Association was formed to undertake the draining of the Central and Gold Hill group of mines, and at the present time a depth of 2,500 ft. has been reached in the Ward shaft. The situation at the Ward looks promis¬ing, and the 3,000-ft. level may be reached in the near future. It is proposed to establish a large pumping-station on this level, and then begin the opening of known ore-bodies and the prospecting for new ones. The main factors which have contributed to the successful solution of the drainage problem are the Sutro tunnel, the use of the hydraulic elevator as a sinking-pump, the concentration of pumping-units, and cheap electrical power. The question of high temperature and its control still remains as a minor but important problem. The temperatures encountered in the new workings are as great as those in the earlier periods. The Comstock was considered the hottest group of mines in the world, and I am not aware of similar conditions in any other mining-district. A water-temperature as high as 160° F. has been reported from the Ward shaft, and temperatures below the Sutro tunnel are very high in many instances.

Nov 1, 1909

By S. L. Windes

This report presents a tabulation of the physical and petrographic properties of Over 100 rock types from operating mines or mineral-investigation projects. The physical properties include the following: Apparent specific gravity Apparent porosity Compressive strength Flexural strength, (modulus of, rupture) Impact toughness Abrasive hardness Scleroscope hardness Modulus of elasticity (Young's modulus) Modulus of rigidity Specific damping capacity Longitudinal bar velocity

Jan 1, 1949

R. W. Raymond, New York, N. Y,:—Since the presentation of my note on this subject at the New York Meeting, Professor Louis has pointed out an error in my statement of his conception of " pitch "—namely, he understands the pitch, in the restricted sense which he proposes, to be the angle of inclination of the axis of an ore-body, measured on the vertical plane drawn through the body; whereas, I represented him as proposing to define " pitch " as the angle of inclination of an oblique body, measured on the plane of the dip, in the direction of the strike. The difference will appear upon consideration of the accompanying isometric projection, Fig. 1, in which ABCD represents the plane of the inclosing ore-deposit (vein or bed), and AC the axis of the oblique ore-shoot. ABE is the angle of the dip, as universally understood; and ACE

Jan 1, 1909

By Daniel Harrington

For several years the United States Bureau of Mines has been making a study of ventilation in metal mines, this study covering practically all the important mining districts of the country. One of the districts where a close and extended study was made was that of Butte, Mont., with its numerous interesting problems and conditions. In February, 1916, Daniel Harrington, mining engineer of the United States Bureau of Mines, was detailed to investigate the circumstances surrounding the death of 21 men in the fire at the Pennsylvania mine at Butte, and during that investigation he made underground visits to several of the large mines through the courtesy of the mine operators, and became much interested in the ventilation conditions. In May, 1916, Mr. Harrington was detailed te work in cooperation with Dr. A. J. Lanza of the United States Public Health Service in an investigation of the prevalence and causes of miners' consumption in the district. This work broadened so much that the investigation was not completed until late in 1918, the investigators making a detailed inspection of all working places in four large mines and a more or less extended examination of conditions in about 20 other mines. Ventilation was recognized immediately as being an important factor in the health of miners, and from the outset of the investigation a large part of the work consisted in obtaining and compiling data relative to the flow of air, humidity, and temperature. The officialsof the North Butte mine were engaged in making a study of ventilation problems before the coming of the investigators, so that opportunity was given to work with those officials for several months. Detailed data on air flow, temperatures, humidities, and an analyses had been obtained before the fire in the North Butte mine June 8, 1917, which resulted in the loss of 163 lives. Much information was obtained during the progress of the fire, and a detailed examination was conducted after the fire, hence an exceptional opportunity existed to study conditions relating to ventilation. This bulletin is a result of studies made from the data collected during the two and one-half years of study and observation a-boveoutlined. Its publication has been delayed through lack of funds for printing. Other publications relative to metal mine ventilation -in other parts of the United States are expected to follow.

Jan 1, 1923

By Mohsen Mohammadi, Edward Cyr

"To date, several studies have been performed on the static mechanical properties of SLM-AlSi10Mg alloy. There have also been more recent studies on the relation between scan strategy, texture, and mechanical properties of SLM metals and composites. However, there is a huge knowledge gap in the available literature regarding texture and mechanical behavior of SLM-AlSi10Mg alloy under high strain rates. Therefore, in this study, dynamic mechanical behavior of AlSi10Mg_200C alloy manufactured by DMLS technique was investigated at high strain rates ranging from 900/s to 1700/s using Split Hopkinson Pressure Bar. Texture using X-ray diffraction technique of the initial samples were measured. The yield strength, peak flow stress, and ductility increased in all samples with increase of strain rate. TEM studies have also revealed evidence of continuous dynamic recrystallization in grains after 900/s–1700/s strain-rate tests. A Taylor polycrystal crystal plasticity constitutive model was then developed to capture and predict the texture evolution and mechanical response under dynamic loading, using plastic work as a critical parameter for the onset of recrystallization.INTRODUCTION Additive manufacturing (AM) powder techniques are among the fastest advancing breakthroughs in manufacturing in recent years, defined by a bottom-up layer by layer process of joining with energy input from lasers or electron beam (Herzog et al., 2016; Gibson et al., 2015). Among alloys fabricated by SLM, AlSi10Mg is of high interest to industry and academia due to its low density, high specific strength and excellent corrosion resistance, making this alloy a viable contender for aerospace, automotive, and marine applications. Circumstances such as car crash or bird aircraft strike hazards subject potential additively manufactured AlSi10Mg parts to impact loadings. This drives an interest in understanding and predicting dynamic behaviour of these alloys. AlSi10Mg is the AM counterpart of A360 die-cast aluminum, which possess hypoeutectic microstructure (Li et al., 2015). Up to the present time, many studies have presented the mechanical properties of SLM-AlSi10Mg alloy. The mechanical properties and microstructure of AlSi10Mg produced by selective laser melting (SLM) or DMLS techniques can be controlled using different parameters, such as feedstock powder (Asgari et al., 2017), and process parameters (Olakanmi et al., 2015). The microstructure and mechanical properties of AlSi10Mg can also be controlled using post heat treatment after SLM process Li et al., 2016). The mechanical properties of SLM-AlSi10Mg are sensitive to strain rate and can both change under quasi-static (Rosenthal et al., 2017) and high strain rates (Asgari et al., 2018). However, a significant knowledge gap in available literature regarding modeling these behaviours, and especially micromechanical modeling of dynamic behaviour."

Jan 1, 2018