Search Documents

By John D. Bardill

A cooperative project between the Bureau of Mines, Department of the Interior, and the Montana School of Mines, investigating results of hydraulic systems for transporting sand slurries for emplacement, was begun in August 1955. In such circumstances, the Bureau provides funds for a fellowship leading to a Master of Science degree as well as available instruments, tools, supplies and equipment. The School provides the ore-beneficiating laboratory with its equipment for use as a pilot plant. The success of a hydraulic backfilling method employing mill tailings depends largely upon the physical characteristics of the tailings. One of these characteristics is size distribution, especially in the finer size ranges. When being emplaced underground, almost impervious layers of slimes separate from some types of mill tailings containing a high percentage of slimes and settle on the top of the sand fill. These coatings may be so dense that the water in the slurry cannot percolate through them for proper drainage. Successive layers of fill in a stope, each with an impervious coating on top, sometimes build up a hydrostatic head, creating pressure on the bulkheads. This may cause breaks in the lining material, inducing sand runs and flooding the level and sumps below. Deleterious slimes flocculated and disseminated throughout the sands should help prevent the formation of impervious slime layers, increasing percolation and settling rates.

Jan 1, 1960

By COLIN A. LAWRENCE, Anthony Del Vescovo

All Rights Reserved. Printed in the United States of America. Information contained in this work has been obtained by SME, Inc. from sources believed to be reliable. However, neither SME nor its authors guarantee the accuracy or completeness of any information published herein, and neither SME nor its authors shall be responsible for any errors, omissions, or damages arising out of use of this information. This work is published with the understanding that SME and its authors are supplying information but are not attempting to render engineering or other professional services. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of the publisher. Any statement or views presented here are those of individual authors and are not necessarily those of the SME. The mention of trade names for commercial products does not imply the approval or endorsement of SME.

Dec 1, 2017

By Pierre de P. E. M. Ricketts

HAVING had occasion while in Europe during the past summer to visit some of the foreign mints and assay offices connected with the same, I thought a brief description of the general process of coining employed, and such items connected with assaying as were new, might prove interesting to the Institute. The principal foreign mints are: the Royal Mint, London; and the mints in Paris, Brussels, Utrecht, Berlin, Vienna, Copenhagen, St. Petersburg, Stockholm, Madrid, Milan, Rome, and Constantinople. My time only permitted my visiting a few of the principal and largest given in the list, and for a description of the remainder I am indebted to the kindness of Mr. James M. Napier, who in company with the deputy master, and chemist of the Royal Mint, made a complete inspection of all the European Mints in 1870.

Jan 1, 1876

By Kah Lert

"The Red Mountain porphyry molybdenum deposit is situated in the Big Salmon Range, approximately 80 km east-northeast of Whitehorse, Yukon.Red Mountain is underlain by Paleozoic, argillaceous sedimentary rocks of the Yukon Cataclastic Complex, which have been intruded by a multi-phase mid-Cretaceous stock.Mineraliwtion, quartz stockwork, metal zonation, and an alteration assemblage characteristic of a porphyry molybdenum system have been superimposed on quartz monzonite porphyry and adjacent homfelsed sedimentary rocks. A later, barren and pyritic quartzeye diorite porphyry body and related dikes have dissected the quartz monzonite porphyry, homfelsed sedimentary rocks and associated molybdenite mineralization.Drill-indicated geological reserves of molybdenum mineralization outlined consist of 187 270 000 tonnes grading 0.167% MoS2.IntroductionLocationThe Red Mountain porphyry molybdenum deposit is located at 60°59'N, 133°44'W (NTS 105 C), approximately 80 km east-northeast of Whitehorse, Yukon. The property is situated within the rugged Big Salmon Range, 15 km east of the north-northwest-trending Teslin River. Red Mountain, at an elevation of 1702 m, consists of relatively steep, talus covered slopes with prominent gossanous bluffs marking the southeast flank. Relief on the property is 700 m, with tree-line at an elevation of 1450 m to 1500 m (Fig. 1)."

Jan 1, 1995

By Jos. Kalbhenn

PART of the plan of re-allocation evolved by the engineers of the Dominion Steel and Coal Corporation in 1932 to retard the rapid advance of the submarine workings seawards was the opening of Dominion No. 20 Colliery, in the Harbour seam, by a pair of cross-measure tunnels from the workings of an older mine working the Phelan seam, which lies 430 feet below the Harbour seam. The tunnels, 8 ft. by 13 ft. in size, were started away from the old workings of Dominion No. 2 at a point 1.5 miles beyond the shore line and were driven on a rising grade of 1 per cent for a distance of 5,335 feet, tapping the Harbour seam at a point 2 ¼ miles off-shore. For transportation and ventilation, shafts and roadways already existing in the Phelan seam were made use of during the stages of development and up to the present time. One of the two tunnels served as a main haulage road and an intake airway, and the other as a return airway and travelling road. However, as the workings of this new colliery expanded, the need for additional airways arose as was anticipated when the plans for the development were formulated. To meet this need, work was started on October 1st, 1942, to establish a new opening between Nos. 2 and 20 Collieries in the form of a vertical shaft to provide a passageway for the ventilating air current of some 250,000 cubic feet per minute on its return to the upcast shafts in No. 2 Colliery, thus making both tunnels available for intake airways. In the interest of safety, speed, and economy, the shaft was raised from the Phelan to the Harbour seam. It is 20 ft. by 12 ft. in size and, with the exception of three timbered compartments across the narrow end, is untimbered. One of the three timbered compartments housed the ventilating tubing and pipe lines, the centre one served as a cage-way for hoisting men and material during the operation of raising, and the third one contained a ladder way. The rest of the shaft was filled with debris during the period of shaft raising.

Jan 1, 1944

By W. W. Fowler

ORIGINALLY designed for copper smelting only, the reduction works of the Cerro de Pasco Copper Corp. have been expanded over the years until now twelve different metals are produced, together with some seven other items which are used locally. Although the total tonnage treated is comparatively modest, as smelting plants go, the variety of operations makes one of the most complex and interesting metallurgical problems in the world. The original plant, at La Fundicion, operated from July 1906 until September 1923. In 1922 a new copper smelter was built at La Oroya, which produced its first copper on Nov. 23, 1922. It is in this plant, greatly enlarged, that metallurgical operations now center. La Oroya is situated at the junction of the Cerro de Pasco Railroad and the Ferrocarril Central del Peru, at an altitude of 12,175 ft.-well over two miles. Many of the various operations stem from two principal smelting circuits which are themselves of conventional types. Copper ores and concentrates are roasted, smelted in reverberatory furnaces and converters, and blister copper produced. Lead ores, concentrates, and other materials are sintered, smelted in blast furnaces to crude lead which is partially fire-refined, and finally electrolytically refined by a modified Betts process.

Jan 1, 1945

By James G. Lyons

All machines vibrate and make noise. An increase signals impending trouble. Vibration and noise analysis allows the condition of the machine to be determined without costly interruption in service for disassembly and physical inspection.

Jan 1, 1977

By H. W. Busch

In the course of examinations by representatives of the Bureau of Mines of several compressed-air systems in which explosions had occurred, samples were obtained of the carbon deposits that are formed normally in various parts of the systems by decomposition of the compressor lubricating oil. Experimentation with these carbon deposits has demonstrated that they contain a "carbon-oxygen complex" similar to that formed on coal and on other carbonaceous materials and generally recognized as being the cause of spontaneous heating of coal. The exothermic properties exhibited by such a complex are considered significant in relation to the possible initiation of combustion reactions that may lead to explosions or formation of carbon monoxide in compressed-air systems. This report discusses the occurrence of explosions and formation of carbon monoxide in the use of compressed air and presents results of experimentation conducted with carbon deposits from air compressors.

Jan 1, 1949

By Cornelius F. Kelley

DURING the war, events moved with unprecedented rapidity. Situations, industrial, economic and financial, arose over night that stressed to the uttermost the ingenuity and ability of those who dealt with them. It was essentially a time demanding action rapid and concentrated, and not one for discussion, either academic or polemic. As a result, matters of importance were necessarily transacted without the desirable opportunity being afforded of enabling a general understanding to be gained as to the relative merit or demerit involved, and in some instances, legislation essential to enable the consummation of an important matter was passed without attracting the public attention then deeply engrossed in the larger aspects of the situation. The result was that so long as the public mind was occupied, little or no concern was given to questions that ordinarily would have invited immediate attention; and in some instances, only when as an aftermath of war a particular subject has become a matter of discussion, criticism not altogether fair is made without first obtaining accurate knowledge as to the conditions that prevailed, the purpose sought to be accomplished, or the results obtained by the action taken.

Jan 1, 1921

By Brian M. Harney

The technique of remote sensing, used for many years by earth scientists, is being applied to the detection and monitoring of air pollution. Instrumentation being developed is of a very diverse nature and is effective, Fn varying degrees, at ranges from 1,000 meters to the altitude of a space satellite. This paper describes a number of the recent developments in this new field. Instruments based on spectroscopic, laser, and photographic systems are discussed. Sensors are being developed which utilize correlation spectrometry, interferometry, Raman scattering, Mie scattering, laser line absorption, and simple photographic detection.

Jan 1, 1973

By Norman G. Foster

The mass spectra of four tertiary butyl substituted thiophenes are reported. A comparison and contrast with earlier structure correlations made by API-RP48 mass spectroscopists is presented. The fragmentation routes of these types of molecules are discussed and explained in terms of existing theories in mass spectrometry. Low ionization voltage data are presented to support the mechanistic picture developed. Structures are inferred about some of the ions, and these are correlated with existing theories. Metastable peaks in the spectra are used to support the fragmentation paths. The presence of doubly charged ions in the spectra is noted and the possible implications toward mechanisms discussed. The general picture of simple, small fragments leaving the ion moiety upon further fragmentation is developed in detail. Some suggestions are presented for further work utilizing isotopically labeled molecules to establish firmly the general picture of fragmentations of the alkylthiophenes.

Jan 1, 1966

The Canadian concept for nuclear fuel waste disposal is being assessed by AECL Research in a series of experiments at its Underground Research Laboratory (URL) near Lac du Bonnet. Manitoba, Canada. As pan of this research, the Mine-by Experiment has been designed to obtain information on rock mass behavior, the development of an excavation-induced damage zone and failure mechanisms around a circular bored tunnel. An iterative design approach was used to effectively reconcile the experiment objectives and construction logistics. This paper discusses the design considerations and construction methodology adopted on the project.

Jan 1, 1991

By J. -C. Sztuke, M. Cao

ABSTRACT The correlations between froth recovery of coal and air recovery were investigated using a hybrid mechanical flotation column. The particle slurry was fed onto the surface of air-water two phase froths to carry out the tests. Froth recovery was taken as the recovery of particles into the froth product, whereas air recovery was determined by the froth height method. The relationships between froth recovery and air recovery were nearly linear, with greater slopes for more hydrophobic particles. Inside the froth phase, the particles were stratified, with hydrophobic particles concentrated in the upper region and hydrophilic particles in the lower region.

Jan 1, 2013

By A. B. Hooker, E. J. Coggeshall

"Dry cells are modified wet primary cells in which the electrolyte is held by absorbent material so that it does not spill aid the cell jars are sealed to prevent evaporation of the absorbed electrolyte. Most dry cells in commercial use are modifications of the Leclanche wet cell. In their usual form they have a hollow cylindrical zinc negative pole that constitutes the containing vessel. An absorbent material, either as a lining in the zinc jar or a bag, separates the zinc cylinder and a rod or flat plate of carbon placed axially inside. A mixture of crushed coke, graphite, and manganese dioxide is tamped about the carbon rod, and the whole mass is saturated with salaanoniac-zinc chloride solution.Dry cells are suitable for services that require minute currents continuously or larger, though limited, amounts of current intermittently. Though limited in this way, they have a wide use, even in underground mining. This paper details some of the applications of dry cells in mines, particularly from the standpoint of greater safety through their use.APPLICATIONSThere are four fields of application of dry cells to mining: (1) Electric shot firing; (2) auxiliary lighting; (3) signaling; and (4) testing.SHOT FIRINGFiring an electric detonator requires very little electrical energy because although the current flow may be 1 to 3 amperes the duration of flow is so small (1 to 4 milliseconds) that the energy withdrawal per shot is almost negligible. Batteries for shot firing need not be large; they may be used for firing either single or multiple shots."

May 1, 1934

By Karl J. C. Harries

Mineral Agreements and Royalties

Jan 1, 2003

By B. Benmokrane, G. Ballivy

"RésuméLe mécanisme de transfert des charges et le processus de décohésion le long des scellements d'ancrages scelles dans des massifs rocheux sous des charges de tensionnement peut être examine par instrumentation de l'ancrage à l'aide de jauges de déformation. Dans ce contexte il est présente ici les résultats d'une étude, en vraie grandeur sur chantier, ayant porte, d'une part sur des essais d'arrachement conventionnels et d'autre part sur des essais déflagrée barres d'ancrages instrumentées et scellées à l'aide d'un coulis de ciment dans un massif rocheux sain et compètent. Les résultats décrits ici, particulièrement les profits de contraintes de cisaillement le long de l'ancrage, obtenus à partir des valeurs de déformations relevées sur les jauges, ont permis de préciser le niveau de chargement correspondant à la décohésion initiale du coulis de scellement, d 'examiner l'effet de la décohésion sur la distribution des contraintes et de caractériser le fluage du système barre d'ancrage/coulis de scellement.ABSTRACTThe load transfer mechanism and the debonding process along grouted rock anchor, subjected to tention loads, can be examined through the instrumentation of the anchor with the aid of strain gauges. In this context, the resultsof a full-scale site investigation including classical pull out tests and creep tests are presented in this paper. These tests were performed on instrumented bars which were cement grouted in a competent rock mass. Results presented in this paper concern, among others, shear stress pro/ties along the grouted anchors which were determined from strain values obtained from the strain gauges. These results have been used to: (1) predict the load level corresponding to initial debonding of the grout; (2) study the effect of debonding on shearstress distribution along the anchor; and (3) characterize the creep behavior of the bar anchor/cement grout system."

Jan 1, 1991

By Ernest A. Hersam

"INTRODUCTION.Luring the year 1923 a complete survey was made of the condition of research in the reduction (milling) and concentration of ores and nonmetallic minerals - that is, up to the stage where the ores or concentrates were ready for hydro- or pyro-metallurgical treatment. This survey was carried on under the general supervision of L. A. Lyon, assistant director and chief metallurgist of the Bureau of mines, in cooperation with the milling committee of the American Institute of mining and metallurgical Engineers, the Massachusetts Institute of Technology, and the University of California. Other institutions, including the National Research council, were of assistance and outlined recommendations during the study.While this report is on ""ore dressing"", it contains short sections on coal and clay. The mechanical handling that these minerals undergo is ""dressing"", so that ore dressing is inclusive of metallic and nonmetallic minerals. ""milling"", in its broadest sense, includes with ore dressing certain other metallurgical treatment which the report is not designed to cover.The survey revealed that considerable experimentation is being carried on great cost to the mining industry, but that the research is in general poorly coordinated while companies and firms are adequately taking care of routine tests and the mechanical features involved in their own operations, no comprehensive study of the fundamental principles of ore reduction is now in progress or contemplated. Many industries, besides mining, are interested in the preparation of materials for final treatment, rendering this investigation of value also to them. This class of fundamental research is neglected by industry unless there is some agency which can bring together at least a majority of this interested in a cooperative effort. It can not be effectively handled by a single company; and, moreover, no company can be expected to bear the whole burden of an investigation to benefit the entire industry or a number of industries hence there is need for concerted study within reasonable limits. Furthermore, co-operation eliminates duplication, which is largely a waste of effort and capital."

Mar 1, 1925

By R. H. Pemberton

"THE Mattagami district of Quebec has, during the past few years, experienced intense exploration by virtually every mining company operating in Canada. As a result of this activity, a number of well-mineralized zinc-copper bearing bodies have been found, some of which will almost certainly go into production. Much of the area has undergone what is now termed ""Saturation Prospecting"" or intense and detailed geological and geophysical surveying, followed by the drilling of nearly all possible bets. Considering only the airborne geophysical surveying, some blocks of ground have been flown by virtually every geophysical instrument which has to date been installed in an aircraft. A list of these different geophysical instruments would include: l. Fluxgate-type total field magnetometers 2. Vertical field magnetometer ,3. Nuclear-precession magnetometers 4. Single-frequency out-of-phase electromagnetometers 5. Dual-frequency out-of-phase electromagnetometers 6. Horizontal component measuring electromagnetometers 7. In-phase and out-of-phase electromagnetometers8. Dip-angle measuring electromagnetometers."

Jan 1, 1961

By E. H. Burroughs

Persons interested in th_e study of petroleum and allied substances have long felt the need of a bibliographic index to the literature. This bibliography, which is intended to be the first elf a yearly series, has been compiled by the petroleum division of the Bureau of Mines with a view to satisfying this need. The references include only the more noteworthy writings that appeared during the year 191.5 in both ·the United States and foreign countries. Only patents plainly applicable to the industries in point have been included, although, of course, a close scrutiny of the great volume of patent literature might reveal many other patents of possible value. The references are arranged according to the subject classification on pages 3 to 11. This classification, which is to be followed in the succeeding bibliographies of this series, is offered as a guide for further study and classification of the pertinent literature.

Jan 1, 1918

By JOHN LANE DYNAN

HE Tonopah Extension property consisted originally of three claims, with an area of 38 acres. In 1902 a shaft, now known as No. 1, was started near the eastern end of the property, close to the Tonopah Mining Co.'s boundary line, in the. andesite cap rock' which covers the ore-bearing formations in the western end of the Tonopah district. A short distance below the 60-ft. level, the orebodies pinched out, although the veins continued. This shaft has not been used since 1916. Before 1910, the production was small, coming mostly from small shoots of high-grade shipping ore. In that : year, the, company started its 30-stamp mill and cyanide plant; the mill was later enlarged to 50 stamps, with a corresponding increase in the cyanide-plant capacity, which brought the capacity of the mill up to 350 .tons per day. The total production of the mine to Oct. 1, 1920, is 871,177 tons of ore, from which was recovered 15,267,216 oz. of silver and 156,241 oz. of gold.' This makes an average recovery per ton of 17.5 oz. silver and 0.179 oz. gold. The average price received for silver since' the beginning of operations is 65.87 c. per oz., and the average value recovered from the ore-'is $15.25. The area of the property has been gradually increased by purchases and consolidations of adjoining ground until it is now 647 acres. A new shaft, known as No. 2, was started in 1912, 1600 ft. west .of No. 1, and in the following year a crosscut on the 750-ft. level of this shaft resulted in the discovery of the. Murray Vein system, from which the greatest prosperity of the mine has come. This vein, with its related veins,

Jan 1, 1921