Search Documents

By Gordon MacVean

THE adoption of rock dusting, as a safety measure, has made notable progress in the West Virginia coal mines since May, 1925. At that time there were but two mines in the State that were thoroughly rock dusted, mines No. 2 and No. 12 of the Boone County Coal Corp., at Sharpless. Since then it is probable that 75 per cent of the coal operators in the State have given consideration at one time or another to rock dusting. This growth of interest followed the meetings of the various mining institutes all over the country, during the summer of 1925, at which papers were presented, drawing the attention of the coal mining operators to the merits of this safety measure. Yet outside of the experience with rock dusting at the Old Ben Coal Corp., of Southern Illinois, and the Carbon Fuel Co., of Rains, Utah, there had been no actual occurrence in the coal mines of the United States, which could be taken as positive evidence of the efficacy of rock dusting in the prevention of the propagation of coal dust explosions. The U. S. Bureau of Mines, however, had run innumerable tests under conditions which closely approximated actual coal mining conditions and had clearly shown that rock dusting was effective.

Jan 1, 1926

By Klaus Rieker

North of Antwerp central train station, two single-track tunnels for the high-speed train line between Brussels and Amsterdam were constructed. At the same time, the central train station was modified to a through station. Both 1.23 km tunnels are situated in the Antwerp sands and were constructed using a slurry shield machine. Due to the inner city location, the tunnels run over their entire length underneath structures, in some cases with only minimal clearance. The paper deals with these challenging situations. In addition, the tunnel boring machine, the tunnel lining and measures to limit settlements will be introduced.

Jan 1, 2007

To allow routine measuring of the exposure of underground workers to N02 from diesel engines and residual gases from blasting. The Approach: A miniature sampler absorbs NO2 which can be measured using a simple method adaptable to both multiple automatic analyses or individual on-site analysis. How It Works: The NO2 sampler is encased in a plastic tube approximately half the length of an ordinary ball point pen and clipped to an underground worker's hard hat. Removal of the end cap activates the personal sampler. Air from the working place enters the open end and diffuses at a controlled rate down the tube interior. The diffusion rate is dependent on tube dimensions (ratio of cross-sectional area to length). The closed end of the tube contains stainless steel mesh which is coated with triethanolamine (TEA) for absorbtion of all NO2 reaching it. Other oxides of nitrogen are not absorbed. The amount

Jan 1, 1975

By G. L. Oldright

This paper is the fourth of a series of preliminary papers on smelting in the lead blast furnace.4 The objects of this investigation are to determine the conditions obtaining within the blast furnace by direct experimentation and to correlate these conditions with operating factors, furnace behavior, and metallurgical losses. ACKNOWLEDGMENTS The authors wish to express their appreciation to the management of the International Smelting Co. at Tooele, Utah, for their whole-hearted cooperation in this investigation.

Jan 1, 1929

By H. H. Murray

The largest reserves of palygorskite in the world are located in Anhui and Jiangsu Provinces in East Central China. The deposits are Middle Miocene in age and range from 3 to 6 m in thickness. The deposits are the alteration product of basaltic volcanic ash. The Chinese Geological Survey estimates the palygorskite reserves are in excess of 200 million tons. The elongate particle shape results in unique colloidal properties. Large quantities are exported to Japan, Taiwan, Southeast Asia, New Zealand, Australia, and West and Gulf Coasts of the United States. The markets include agricultural carriers, paint, joint tape compounds, animal feed binders, catalyst support, drilling muds, and suspending agents for chemicals, pharmaceuticals, and medicines. The viscosity is high and the quartz content is generally 5% or less.

Jan 1, 2009

By D. Kwietnewski

With all of the unknowns associated with tunnel construction, how does a contractor choose a roadheader? This paper presents a review of several models of roadheaders being used in today?s tunnel projects. The features of different models of roadheaders are presented and compared. Roadheader size and cutter power generally determine which roadheader is best for a particular job. We will also present a model for matching features of the roadheader to the anticipated ground conditions such that the most efficient machine is selected for the project.

Jan 1, 2011

By W. L. Barry

A review of the practices of analyzing for precious metals at the Reno Research Center, U.S. Bureau of mines, is presented. A general description of fire assaying, the physical layout of a fire assay laboratory, and the use of fire assaying in combination with atomic absorption, induction coupled plasma, and emission spectroscopy is reviewed. The combination of techniques significantly decreases the detection limits for precious metal analyses and simplifies the analysis of the platinum-group metals. Methods of protecting personnel from ingestion of lead are also discussed.

Jan 1, 1982

By A. Golshani, M. Oda, K. Suzuki, T. Takemura

Anisotropic behaviours of OhshimaOshima granite were investigated by carrying out uniaxial compression tests, together with observations of microcracks under an optical microscope. The elastic modulus tensor of Oshima granite at 10 per cent strength,E10, were calculated using theoretically formulation of elastic modulus tensor in terms of the second-rank crack tensor for pre-existing open microcracks. Furthermore, with the assumption of orthorhombic elasticity, the nine moduli of Oshima granite E10were determined by uniaxial compression test. Twenty-onemoduli of samples, calculated without assuming any symmetry, also showed orthorhombic features. Direction of the symmetry axes agreed well with the orientation of preexisting cracks. Comparison of crack tensor-based formulation results with the experimentally determined one show that the anisotropy of elasticity of Oshima granite is caused by pre-existing open microcracks, not by pre-existing healed microcracks and also crack tensor formulation can be used, as a first-order approximation at least, to describe the anisotropy of Oshima granite induced by pre-existing open microcracks. ZUSAMMENFASSUNG: Das anisotrope Verhalten des Oshima-Granits wurde mit Hilfe voneinachsigen Kompressionstests und durch die Betrachtung von Mikrorissen unter einem optischenLichtmikroskop untersucht. Das Elastizitätsmodul von Oshima-Granit bei 10 Prozent Kraft E10wurde berechnet, indem man die Formulierung des Elastizitätsmodultensors, ausgedrückt alsRisstensor zweiter Ordnung theoretisch auf bereits existierende Mikrorisse angewandt hat.Außerdem wurden die neun Module des Oshima-Granits unter der Annahme orthorhombischerElastizität E10mit einem einachsigen Kompressionstest bestimmt. Einundzwanzig Stichproben,die ohne die Annahme irgendeiner Symmetrie genommen wurden, zeigten ebenfallsorthorhombische Merkmale. Die Richtung der Symmetrieachsen stimmte mit der Orientierungbereits vorhandener Risse überein. Der Vergleich der Ergebnisse der auf dem Risstensorbasierenden Formulierung mit der experimentell bestimmten Formulierung zeigt, dass dieAnisotropie der Elastizität von Oshima-Granit von bereits vorhandenen offenen Mikrorissenverursacht wird, und nicht von vorhandenen vernarbten Mikrorissen, und dass dieRisstensorformulierung auch zumindest für eine Annäherung erster Ordnung benutzt werdenkann, um die durch vorhandene offene Mikrorisse induzierte Anisotropie des Oshima-Granits zubeschreiben. RESUME: Les comportements anisotropes du granit d’Oshima ont été étudiés en réalisant destests de compression simple, et en observant les microfissures au microscope optique. Le tenseurdu module d’élasticité du granit d’Oshima sous une résistance de 10 pourcents, E10, a été calculéen se servant de la formule théorique du tenseur de module d’élasticité basé sur le tenseur defissures de second ordre des microfissures ouvertes préexistantes. En outre, sur base del’hypothèse de l’élasticité orthorhombique, les neuf modules du granit d’Oshima ont étédéterminés par des tests de compression simple. Vingt et un modules d’échantillons, calculés endehors de toute hypothèse de symétrie, ont aussi montré des caractéristiques orthorhombiques. Ladirection des axes de symétrie correspondait bien à l’orientation des fissures préexistantes. Lacomparaison des résultats de la formule basée sur le tenseur de fissures avec les résultatsdéterminés expérimentalement montrent que l’anisotropie de l’élasticité du granit d’Oshimaprovient des microfissures ouvertes préexistantes, et non de microfissures préexistantes referméeset que la formule du tenseur de fissures peut servir, au moins comme première approximation, àdécrire l’anisotropie du granit d’Oshima marqué par des microfissures ouvertes préexistantes.

Jan 1, 2003

By Caruline de Souza Carvalho Machado

Tensões residuais podem ser muito prejudiciais ao desempenho de um componente, tornando sua quantificação e avaliação extremamente uteis. A difração de raios-X é um método de análise não destrutivo que permite avaliar as tensões sem comprometer o material. Neste trabalho, tiras de aço duplex UNS S32304 com 1,8mm de espessura foram cortadas nas dimensões 36x72mm e soldadas de modo autógeno através do processo TIG. Produziram-se dois tipos de amostras variando-se o gás de proteção a saber: mistura de argônio 98% e nitrogênio 2% e argônio 99.995%. Utilizou-se um difratômetro com geometria Bragg-Brentano, fonte de radiação CuKa ( = 1,5419Å). A técnica sen2 ? foi empregada para determinar a tensão residual da fase austenita no ângulo 2?=146.22°. Os resultados mostram um estado de tensões residuais trativo nas proximidades da zona fundida, chegando a um estado compressivo em regiões distantes. A análise comparativa dos perfis de tensão residual revela que a amostra soldada apenas com argônio apresenta menor tensão residual trativa na zona fundida.

Aug 8, 2018

By Fernando Bermejo

El presente texto describe la implementación del método Flash - Flotation para el proceso de optimización de plantas concentradoras polimetálicas en la Compañía minera Raura donde se tienen diferentes gravedades especificas por cada especie mineralógica. Su aplicación comprende la fase de investigación (año 89), modificaciones (año 2002) durante la etapa de escalamiento industrial y la optimización (año 2004) de estos equipos en la empresa, los cuales no han requerido de una gran inversión. Asimismo, los beneficios de operar con la celda SK-80 y SK-240 directamente a la descarga de los molinos primarios, permite optimizar el control metalúrgico. En este sentido, la idea de separar el plomo tan pronto lo permita el sistema, es la forma correcta de optimizar la metalurgia de este en la Compañía minera Raura.

Sep 12, 2005

By Joan T. May

The Bureau of Mines conducted laboratory tests to evaluate the production of high-purity H3P04 by HCl digestion and solvent extraction. Both batch and bench-scale continuous tests were made. Western phosphate rock concentrates were acidulated with HCI, and the digestion liquors were processed by solvent extraction. Phosphoric acid was extracted with isoamyl alcohol and recovered from the organic extract by contact with an NH4F solution. This solution was fractionally distilled to yield high-purity H3P04. The raffinate from solvent extraction was treated with lime to precipitate CaF2, which was subjected to steam pyrolysis to generate HF. This method was successful in recovering 95 pet of the phosphate and 80 pct of the fluoride contained in the concentrates.

Jan 1, 1976

By John S. Corsentino

This Bureau of Mines study is a listing of fuels -related projects that are presently under construction, planned, or proposed by various companies and organizations in the Western United States. The future facilities covered in this report fall into the following categories: coal mines and expansions to existing mines, electric powerplants and expansions to existing plants, coal conversion plants, waste-to-fuel conversion plants, oil shale projects, tar sands projects, potential geothermal facilities, coal slurry pipelines, railroads related to fuels development, uranium mines and expansions to existing mines, uranium mills and enrichment facilities, oil refineries, and natural gas processing plants. The projects are listed by state. Data concerning the company, location, planned markets, process type, initial operating date, capacity, water requirements, employment, current status, and other relevant information are included. Each project has been plotted on an accompanying state map. Due to present uncertainties concerning the fuels industry, some of the listed projects may never he constructed. No attempt has been made to determine the degree of certainty or viability of each project.

Jan 1, 1976

By T. Hadley, E. Catovic

"Northern Minerals Limited’s (ASX: NTU) flagship project is the Browns Range Rare Earth Project (the Project) located in Western Australia, consisting of a number of deposits with high value, heavy rare earth elements, in particular yttrium, terbium, and dysprosium. The deposits are dominated by xenotime mineralisation, which occurs within hydrothermal silicified and hematitic breccias. The Company delivered an initial JORC compliant resource estimate for the Project at the end of 2012 of 10,500 t of contained total rare earth oxides (TREO), which was increased to 28,084t of contained TREO in October 2013 and further enlarged to 47,997 t of contained TREO in February 2014. Concurrent with the growth of the Project resource base, significant progress has been made in developing the metallurgical process for the beneficiation and extraction of rare earth elements (REE’s) from the xenotime mineralisation. Development of the beneficiation circuit evaluated several process options and selected whole-ore flotation and magnetic separation, followed by flotation (hybrid circuit) as the two preferred flowsheets to pilot, following encouraging results on the bench of 83% and 86% recovery to a 20% TREO mineral concentrate respectively. Several downstream hydrometallurgical extraction flowsheets were evaluated. However, the following two preferred process flowsheets were ultimately selected for further detailed investigation during the prefeasibility study: 1. Sulphation bake, water leach, purification, oxalate precipitation, and/or calcination to produce a mixed RE oxide; 2. Sulphation bake, water leach, phosphate precipitation, caustic conversion, HCl leach, and oxalate precipitation to produce a mixed RE oxalate. Excellent heavy rare earth oxide (HREO) extractions (~ 90%) from beneficiation concentrates were achieved on the bench for both circuits, however flowsheet 1 was ultimately selected as the preferred flowsheet to pilot due to lower capital and operating cost. A mixed rare earth oxalate (42% TREO) or oxide (92% TREO) can be produced with low levels of Th and U of 3 ppm and 6 ppm respectively."

Jan 1, 2014

By Slavoljub D. Maksimovic

The Bureau of Mines, through a memorandum of agreement with the State of Ohio, tested a method of constructing seals in abandoned mine openings in Ohio by means of pneumatic stowing of crushed limestone and gravel with sand. A total of five openings and one shaft were back-filled. Pneumatic stowing uses compressed air to convey material through a pipeline and into the mine opening. The stowing equipment consists of a power supply, a blower, a feeder to inject the material into the pipeline through an airlock, and a nozzle for directing the placement. Material is ejected from the nozzle at high velocity, creating a high-compaction fill upon impact. Well-graded aggregate up to 2 inches in diameter and having sufficient fines is used as fill. The stowing method is safer and faster than conventional methods, is cost competitive, prevents trespass into abandoned mine openings, and eliminates or reduces the exposure of workers to possible hazards since the discharge nozzle can be kept at the mouth of the opening. The equipment is mobile, and, with some modification, the technique could be widely used for sealing abandoned and active mine openings, even in remote locations and during severe weather conditions.

Jan 1, 1982

By Colwell J. B, Constantine A. E

A unique, regional grid of deep (12 - 14 second record length), seismic reflection and refraction data has been recorded by the Australian Bureau of Mineral Resources (BMR) across the offshore Gippsland Basin and parts of the adjacent Bass Basin, in southeastern Australia. These data have been combined with onshore mapping to produce a new model for the development of the Gippsland and adjacent Bass Strait basins. Overall, the Gippsland Basin contains up to 12 - 14 km of sediment in an ESE-trending depocentre bounded on its north and northwestern margins by a detachment ramp, and on its southern side by a relatively linear, listric fault system. The basin, together with the adjacent Bass and Otway Basins, appears to have formed as part of a linked, largely- strike-slip to 'transtensional' system, which started to extend through Bass Strait, probably during the latest Jurassic. Each of the basins developed by movement on a common detachment or detachment complex, which produced headwall extension at their western ends, in the areas now occupied by the Strzelecki Ranges, Otway Ranges - Torquay Sub-basin, and Robe Trough. Adjustments and reactivation from the mid Cretaceous of several postulated microplates in the region, largely in response to Tasman Basin rifting, gave rise to the wrench-related and compressional structures which form the major petroleum targets in the Gippsland Basin. However, the same process formed largely extensional stuctures in the Bass Basin. Our interpretation of the tectonic history of the Gippsland Basin leads us to the conclusion that there may have been several phases of petroleum generation and migration, and that potential petroleum traps appear to exist in the deeper section, in structures sometimes not reflected at the top or near-top Latrobe Group levels.

Jan 1, 1992

The design/optimization of the pump and cyclones to maximize grinding circuit efficiency first requires a concise understanding of, and clearly defined specifications for, desired grinding circuit performance. Subsequently, the pump and cyclone performances that provide the desired grinding circuit performance can be defined. Once the performance requirements of each process unit are determined, selection of physical equipment parameters that will deliver those performances can be carried out. The Functional Performance Equation shows that there are two distinct efficiencies in closed circuit ball milling. One of these, ?Circuit Classification System Efficiency? (CSE), is the fraction of ?coarse? material inside the ball mill upon which grinding energy is deliberately expended, versus the remaining fraction of ?fines? or finished size material inside the mill, upon which grinding energy is wasted (on over-grinding). The role of the pump and cyclones is to maximize CSE, which is the desired grinding circuit performance. The obtainable, target CSE for any given circuit can be estimated, for example by referring to a plant data base of CSE?s. Design/optimization guidelines then allow us to specify the pump and cyclone performances that will achieve the target CSE. This paper outlines the step-by-step, systematic method of pump and cyclone selection which maximizes CSE. Numerous examples of its successful application are provided.

Jan 1, 2011

By Ygor Pereira de Lima, Iana Costa Carvalho, Marcelo Henrique Prado da Silva, Talita Gama de Sousa, Andrey Mariano dos Santos, Paulo Davi Borges Esteves, Rodolfo da Silva Teixeira, Andersan dos Santos Paula

Durante muitos anos, as ligas convencionais foram base para o desenvolvimento de novos materiais metálicos, com propriedades melhores que as até então conhecidas. No entanto, na última década, as Ligas de Alta Entropia (LAE) trazem uma nova abordagem para a produção de materiais avançados, com excelentes propriedades e potencial para diversas aplicações. Em particular, as ligas do sistema Al-Co-Cr-Fe-Ni também se destacam por promoverem uma classe de LAE de baixa densidade e têm sido foco de inúmeros estudos no meio acadêmico atual. O presente artigo traz um estudo de otimização da preparação metalográfica da liga AlCo2Cr2FeNi2, a partir de 3 rotas diferentes de polimento e suas análises via microscopia eletrônica de varredura (MEV) e difração de Raios X (DRX). Além disso, foram avaliadas as modificações estruturais da liga em função de um tratamento térmico de solubilização (1050 ºC por 1 hora seguido de resfriamento em água). Os resultados das análises demonstraram a rota de polimento eletrolítico promissora para a caracterização da LAE em questão e a análise conjunta dos resultados de DRX e MEV, somado ao confronto com a literatura, permitiram identificar as fases presentes e suas modificações microestruturais em função do tratamento térmico.

Oct 24, 2019

By S Chew, A Bennett, N Di Giorgio, B Osborne

After relining one of two blast furnaces and enlarging its sinter plant in 2009, BlueScope radically restructured its Port Kembla steelworks operation in 2011, shutting a blast furnace and halving its total production. This drastic move in response to unprecedented raw material prices relative to achievable steel prices was like that of many integrated steelmakers worldwide facing similar challenges. The 2011 restructure also saw major changes in the amount and type of iron ores and ferrous burdens purchased, and a fundamental reappraising of ‘value’ in iron ores. This paper outlines the changes to raw materials purchases from 2011 to 2017, how BlueScope has responded to the changes in pricing and raw materials quality, the effect on the sintering and blast furnace processes at Port Kembla resulting from higher gangue content, some of the broad technical and economic challenges faced by steelmakers confronted with lower quality iron ores and how BlueScope is meeting those challenges.CITATION:Di Giorgio, N, Bennett, A, Osborne, B and Chew, S, 2017. Recent Port Kembla experience with iron ore use – sintering and blast furnace, in Proceedings Iron Ore 2017, pp 25–30 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By J. Brian Anderson

Jointed micropiles were investigated to support bridge foundations where shallow rock was present. In this application, micropiles would have some amount of unsupported length, and would be subject to nominal lateral loads. Five lateral load tests were conducted on micropiles to demonstrate the impact of casing joints and rock socket embedment on lateral behavior. Load tests were simulated with FB-Multipier, a hybrid-finite element program for analysis of deep foundations, for proper design of the loading apparatus and instrumentation. The micropile sections were 2 m (6.56 ft) long, 273 mm (10.75 in) in diameter, 13 mm (0.5 in) thick walled, with a 50-mm (2-in) long threaded joint. Micropiles were made of one to three casing sections and were embedded 0.3, 0.6, 1.5, or 3.0 m (1, 2, 5, or 10 ft) into rock. In each test, two identical micropiles were pulled together using a simple frame until the weaker pile failed. All micropiles were instrumented with inclinometer casings while two contained strain gages at 0.76 m (2.5 ft) intervals. Load and displacement were measured at the pile heads. Tests showed the embedment of 0.6 m, 1.5 m, and 3.0 m (2 ft, 5 ft and 10 ft) sufficiently carried lateral loads over 180 kN (20 tons). The piles embedded 0.3 m (1 ft) were not able to maintain lateral load. In general, all micropiles tested to failure exhibited a brittle failure mode where there is small lateral deflection followed by a sudden failure at the casing joint. This was demonstrated in three of the load tests. In most cases, the micropiles were stiffer and stronger in the load tests than originally predicted numerically. The final test, where piles were not loaded to failure, verified that embedding vibrating wire rebar strain meters in the grout captured the bending moment profile of the micropile. The results showed the maximum moment in this case being carried directly across the threaded joint as predicted by the preliminary models. The results of these tests were used to calibrate the FB-Multipier numerical model. Using a load test that included bending strain measurements for a match, the soil properties were adjusted to produce reasonable matches for all of the load tests.

Jan 1, 2011

The following paper describes the refining practice for the production of lead, silver and gold at the works of The Broken Hill Associated Smelters Pty. Ltd., Port Pirie, South Australia.The refinery is situated on the wharf frontage and is built parallel with it. The refinery occupies an area of approximately 3380 square yards. (Fig. 8)There are two buildings, one containing the softening and de-silverising sections, measuring 225 ft. x 57t ft., while the other building, which measures 225 ft. x 90 ft. covers the de-zincing, lead moulding, retorting, cupellation, and dore parting sections. (Fig. 1)The retorting, cupellation, and dore parting sections are completely isolated from the rest of the plant by strong small-mesh wire gratings welded to steel uprights. The dore parting plant and generator room are further isolated by a brick wall, built up to the roof. The two main buildings are steel structures, with outer walls and roof of "Robertson" corrugated sheeting; the side and end walls are open for some distance above the ground, and this, coupled with the high roof which is 50 ft. from ground level, ensures the free access of air and light. Conditions are such that operators work in a clear atmosphere.

Jan 1, 1937