Search Documents

By S. V. Subramanian

The tool material and the machine design for high speed machining are well advanced over the last decade but the steel design has lagged behind. The paper examines the design of steel in order to control the sliding tribology for high speed machining under dry machining conditions. In high speed machining of steel, accelerated chemical wear of the tool occurs once atomic contact is established at the tool-chip interface, resulting in poor tool life even with high performance tools such as cubic boron nitride. Recent research has confirmed the occurrence of nanocrystalline grains in the interfacial layer of the chip at the tool-chip contact. The volume percentage of grain boundary is increased significantly (10 to 30%) as the nanocrystalline grain size is decreased well below 30 nm. The solubility of tool material into the nanocrystalline grain boundary is two or three orders of magnitude greater than in the crystal lattice. Further the kinetics of diffusion in the grain boundary is seven or eight orders of magnitude greater than in the crystal lattice. Enhanced nanocrystalline grain boundary diffusion occurring in the interfacial layer at the tool-chip contact causes the accelerated chemical wear. Significant improvement in tool life could be achieved by engineering glassy oxide inclusions in steel, designed to self-lubricate the tool-chip interface in-situ at higher cutting speeds. Thus the control of sliding tribological condition at the tool-chip interface is key to suppress nanocrystalline layer formation at the tool-chip contact and hence prevent accelerated chemical tool wear. Sulfide inclusions are designed essentially to promote chip fracture. In addition, sulfide inclusions are designed to act as a diffusion barrier at the tool-chip interface. The application of inclusion engineering concepts to enhance the tool life in high speed machining will be demonstrated with a suitable case history.

Jan 1, 2006

By Hongfa Hu, Stavros A. Argyropoulos

"This paper describes a mathematical model which simulates numerically reaction driven fluid flow phenomena. The driving force of this reaction is an exothermic heat of mixing. In addition, the model predicts the heat and mass transfer phenomena where both heat source and heat sink co-exist in close proximity. The heat source is generated by an exothermic reaction. The heat sink is formed by a moving boundary such as the melting of a solid. This type of phenomena occur quite often in various metal processing operations in which exothermic additions are immersed in liquid metals. The model is based on the SIMPLER algorithm and uses an enthalpy method to predict the fluid flow, temperature, and concentration fields. The results indicate that the exothermic mixing reaction was responsible for an abrupt rise in temperature around the moving boundary. The intensity of this reaction was also found to be responsible for the enhanced convection of fluid and the acceleration of the moving boundary. The modelling results were also verified by experimental work which included velocity and temperature measurements in a low temperature physical model. IntroductionAlloying additions are used extensively in the treatment of liquid metals during metallurgical processes. The alloying additions introduced into liquid metals can be classified into various classes, each of which follows its own route[l]. As a major group, the exothermic additions follow two different steps during their assimilation into liquid metals. In the first step, upon immersion, a metal shell solidifies around such additions, and then melts back. At this point, the second step commences. During this second step, due to the mixing of the addition with a liquid metal, an exothermic reaction occurs, which liberates large amounts of heat, resulting in an enhanced convection in the liquid metal surrounding the addition."

Jan 1, 1994

By Alpagut Kara

Turkey is the fifth biggest ceramic tile exporter in the world. Considering the expectation that the Turkish tile sector continues to expand, further studies both on the improvement and the development of tile formulations are necessary in order to make the producers advantaged in the world market while maintaining the capital and running costs at reasonably competitive levels as well. In addition to such studies, waste management in tile manufacturing has also recently become an important issue. Accordingly, the industrial use of wastes in the traditional ceramic industry has been intensively investigated in the recent years. This work describes part of a detailed research project carried out jointly on the possible re-use of muds (raw production waste) from glazing and pressing lines of a local tile company in the development of new wall and floor tile formulations. In order to achieve this, the waste material was firstly investigated in function of chemical and mineralogical compositions. Then, the particular focus was given to the presence of the waste material in increasing amounts on the thermal behaviour and physico-mechanical properties of the re-formulated tile bodies. During the studies, SEM in combination with EDS, and thermal analysis techniques such as non-contact dilatometry were widely employed. The results indicated that it was possible to use the waste materials in the commercial tile production without deteriorating the relevant technological properties.

Jan 1, 2006

By Fatma Arslan

The lateritic nickel ore sample subjected to this experimental study was taken from Çalda ore deposit (Turkey) and contains 1.43% Ni and 0.105% Co. Mineralogical investigations showed that the ore sample contains asbolane, chromite, limonite, hematite, goethite, lepidocrocite, magnetite, serpentine, and clay type minerals together with chalcedon, quartz, calcite, and chlorite. In the acidic leaching experiments, the effects of temperature, acid (H2SO4) concentration, and leaching time on nickel leaching recoveries were investigated. Leaching recovery versus time curves showed a parabolic trend and increasing the temperature shifted that curves to the higher values. The dissolution of nickel from lateritic ore can be explained by a shrinking core model and the apparent activation energy was found as 47.34 kJ/mol in the range given by the literature. The highest Ni and Co leaching efficiencies as 90.2% and 96.8% respectively were obtained at 80°C temperature, 200 g/L H2SO4 concentration, and 8 hours of leaching time.

Jan 1, 2006

By T. Kozuka, K. Sassa, S. Asai

"A new atomization process is developed. The principle of this process is completely different from that of conventional processes. This process uses electromagnetic energy induced by direct electric current and direct magnetic field instead of kinetic energy produced by fluid impingement or disk rotation.Experimental work of this process was carried out using pure tin, and it was found that the crucial factor for a stable operation is the contact state of molten metal with the electrode. In order to control the condition, a delay time controlling unit was developed and combined with this process. It is noticed that this controller works well to produce uniformly sized particles.A linear relation between the impulse and the momentum of atomized particles is found by use of experimental data and is explained by theoretical analysis.IntroductionIn atomization processes prevailing in metal powder technology, kinetic energy is currently employed for atomizing molten metal. That is, molten metal is broken into small particles by other fluid (e.g. water, argon gas, etc) or by impinged upon a rotating solid disk. This splashing process is always accompanied with uncertain factors for shape and size of the particles. The diameter distribution of products, therefore, comparatively spreads over a wide range. From another standpoint, the restriction of atmosphere is inevitable in some of these processes. As a pulverizing technology, the process which can produce uniformly sized particles and permits the choice of atmosphere is strongly desired.On the other hand, a great attention has been paid to the spray casting process as a new near net shape casting. In this process, a small size spraying device is favorable."

Jan 1, 1988

By George Kachaniwsky

Until mid-1982 the Mines Gaspe copper smelter consisted of a fluid bed roaster, a reverberatory furnace, two Peirce-Smith converters of which only one was blowing at any one time, anode casting facilities, and a single contact sulphuric acid plant treating both roaster and converter gases. Reduced concentrate supplies have led to the shutdown of the roaster and, as a result, it was necessary to adapt the converter and acid plant operation to the new operating mode: green concentrate smelting with resulting lower matte grades and acid plant treatment of off-gases from only one blowing converter. Therefore, modifications were carried out to existing equipment and methods of operation and control. This paper describes the result of work done to obtain steady, maximum strength, converter off-gas flow and an efficient acid plant operation. Topics covered include: optimization of converter operation, tightness of hood and off-gas ducting, improvements in acid plant/converter communications and modifications of acid plant operation and control to cope with the fluctuations in converter gas flowrates and strengths.

Jan 1, 1983

By J. L. Liow

Studies have been carried out on the causes and effects of slopping in an annular cylindrical geometry such as the top submerged combustion reactor. Properties of standing waves formed such as the wave profile, period, pressure distribution and velocity have been derived analytically. The wear profile due to wave erosion was calculated based on the assumption of linear motion and that the wear is a dissolution process. The use of the j, factor showed that the wear was proportional to the square root of the wave velocity at any point. Using the dimensions of the lsasmelt reactor given by Errington et al. (1987)[11, the wear profile due to wave erosion was calculated using the analytical solution. The wear profile calculated was shown to have a maximum just below the initial bath surface. The wear was found to be concentrated in the region where the first asymmetric standing wave was most active. The results showed that the refractory near the bath surface will be affected by wave erosion, more so than any other parts of the reactor. The contribution of wave erosion on wear must be accounted for in assessing the total refractory wear of a vessel in which slopping exists.

Jan 1, 1991

By J. Tang, B. Q. Li, R. Akarapu

"An integrated model is developed to represent the three-dimensional electromagnetic wave propagation and thermal phenomena during microwave heating of ceramics and dielectric/biological materials. The model development is based on the edge finite element formulation for electromagnetic fields and the node fmite element formulation for thermal phenomena. Results are presented and compared well with available analytical solutions and experimental measurements. With the model, the effect of sample positions on the electromagnetic and thermal field distributions is studied.IntroductionMicrowave, as an electro-heating source, has been widely used in the processing industries for packaged foods and other materials. The commonly used household microwave oven is a typical example of microwave heating processes. Other industrial microwave processing systems include large-scale microwave guides and cavities, which are used for the sintering operations as required for making ceramic components or for sterilizing the packaged foods."

Jan 1, 2004

By Tian Tang, Sergio D. Felicelli

"The laser cladding is an important surface treatment for enhancing resistance against corrosion, abrasion, and wear. The focus of the present study is to develop a three dimensional finite element model to analyze the temperature history and thermal stress evolution during multi-pass laser cladding process on H13-H13 tool steel sample. A sequentially coupled thermal-stress analysis methodology was adopted in this study. The thermal model was firstly established to investigate the temperature history of the laser cladding process. Then the temperature history was used as input to mechanical model to calculate the thermal stress evolution during the process and the residual stress after the sample completely cooled down to room temperature. The influences of process parameters including the scanning speed and scanning strategies on temperature history, thermal stress evolution, and residual stress were investigated in details.IntroductionLaser cladding is an advanced material process technique, which is often used to improve mechanical properties or increase corrosion resistance, repair worn out parts, and fabricate metal matrix composites. In this process, the injected powder or wire feedstock material and a thin layer of substrate are melted and consolidated by use of a laser in order to coat part of a substrate or fabricate a near-net shape part.Numerous mathematical models have been established for analyzing the effects of process parameters, microstructure evolution, and thermo-mechanical behavior of laser cladding. Zhou et al. [1] established an analytical model to investigate the laser induction hybrid rapid cladding for Ni-based WC composite coatings. Huang et al. [2] also developed an analytical model to theoretically investigate the interaction between the laser beam and the powder stream of laser cladding process. A simple and realistic model of laser cladding was proposed by Picasso et al. [3]. The cladding layer is very sensitive to cracks due to the accumulation of residual stress, caused by non-uniform temperature changes, which have limited the wide application of laser cladding technique in industry. Recently, fmite element method has been increasingly used to simulate the laser cladding process [ 4-6]."

Jan 1, 2014

By Patrick R. Taylor

Iron phosphate glasses are promising host matrices for vitrifying actinide rich nuclear wastes materials because of their high solubility of actinide oxides, high chemical durability, and relatively low melting temperatures. An iron phosphate waste form was developed at the University of Missouri-Rolla. The structure and property of the waste form were well characterized by materials techniques. However, to scale the process and advance it to commercial viability, it is necessary to understand the processing parameters, such as the partitioning of waste elements and the viscosity as a function of temperature. Viscosity of 40 Fe203 - 60 P205 mole % iron phosphate melts (prepared with phosphorous pentoxide and ferric oxide) at 1000-1200 C was measured by the rotating-spindle method. It was discovered that this fluid has non-Newtonian behavior. Experiments were performed to study flow properties following the Standard Test methods for Rheological Properties of Non-Newtonian Materials by Rotational (Brookfield) Viscometer (ASTM D 2196-86). Samples prepared using ammonium phosphate and ferric oxide showed Newtonian behavior and the temperature dependence of the viscosity was studied over the range of 1000 to 1200 degrees C. The difference in flow behavior between the two fluids was analyzed in terms of preparation conditions and variation in the final composition and phases. The partitioning behavior of waste elements in the iron phosphate glass was studied by melting in a high temperature furnace and JCP analysis. The experimental results show that the solubility of Ce and Sr in phosphate glasses is significantly higher than the solubility associated with borosilicate glasses. This strengthens the conclusion that iron phosphate may be a viable alternative to borosilicate glass for immobilization of high heavy-metal-content wastes and actinide rich wastes.

Jan 1, 2002

By Mamoru Kuwabara

A high-power sound which can transmit through any continuous elastic medium with less attenuation, particularly in liquid allows us to externally control the system of concern by using the acoustic radiation force or the cavitation phenomena. These functions may eliminate gravitational and/or atmospheric constraints which are often encountered in conventional operations for producing clean and advanced materials. This paper outlines the recent development in the field of sonoprocessing of materials. Cold model experiments in some vessels have been performed to simulate ultrasonic operations such as inclusion removal from liquid, degassing of melt, emulsification of two liquid phases, solidification processing, and decomposition of chemical species in waste water. High speed visual imaging is carried out for better understanding of the cavitation phenomena as well as the followed microjets during the processing. The radiation force acting on fine suspending objects in a fluid can be utilized for eliminating or rearranging/orienting the objects in the fluid. Acoustically induced cavitation phenomena in liquid can be utilized as an effective dynamic means to control interfacial phenomena as well as micro- and macro-mixing of liquid. Sonochemical and thermal effects in cavitation multi-bubble can be also useful in a waste water treatment.

Jan 1, 2006

By Gary K. Elliott

Many industrial processes generate hot waste gases which contain particulate pollutants. Conventional clean-up techniques suffer limitations either because collection efficiency is low or because the gas must be cooled before treatment. thereby increasing costs and preventing energy recovery. The application of increasingly stringent environmental legislation to the non- ferrous metallurgical industry Is presently illustrating these conventional technology limitations. Low density ceramic media allow filtration to take place at high temperatures and are now rapidly becoming accepted in many industries. This paper reviews experiences with a proprietary low density ceramic filter element, Cerafill. It includes consideration of the structure, composition. typical operating and case studies with particular reference to non-ferrous metallurgical furnace applications.

Jan 1, 1992

By C. L. Lin

Multiphase, irregularly-shaped randomly-oriented PARGEN particles were grown to determine the breakage/liberation characteristics of such locked particles. The simulated locked particles were randomly broken to establish the liberation characteristics of the broken fragments. The progeny size distributions are consistent with Gilvarry's volume and surface flaw model for single particle breakage. The extent of liberation of both continuous and dispersed phases can be described from the conservation of interfacial area. In this regard the data can be normalized and liberation described for a wide range of dispersed phase grades and dispersion densities.

Jan 1, 1988

By Gavin Beer

The Chelopech Copper/Gold Mine, located in west-central Bulgaria, has been in operation since 1953 producing a low-grade copper/gold concentrate containing up to six percent arsenic by weight. The penalties and restrictions imposed on smelting this concentrate, have seen the past operators of the mine strive to find a balance between achieving acceptable metal returns from the smelters and installing novel or unproven technologies in the face of changing political and economic climates. This paper documents the colourful history of the concentrate processing alternatives that have been investigated and implemented over the 45 year life of the Chelopech Mine, culminating in the high pressure oxidation option that is now the focus of a Definitive Feasibility Study (DFS) presently being undertaken by GRD Minproc Limited. The fundamental chemistry of the preceding alternatives is outlined followed by a discussion as to why each was ultimately not employed. A detailed description of the technology proposed in the DFS is given including: pressure oxidation, arsenic fixation, SX/EW copper recovery, CIL gold recovery and AVR/SART cyanide/copper recovery processes. Keywords: Arsenic, Scorodite, HPOX, Chelopech, Dundee

Jan 1, 2005

By Toshiyuki Kozuka

CdTe semi-conducting materials have been expected as solar cell materials because its theoretical energy conversion ratio is very high. The actual efficiency still low, however, many research works have been done in order to improve the efficiency. And crystal orientation is one of possibilities for that. In this work, a new method using intense magnetic field for a control of texture of CdTe crystals will be proposed, where the CdTe film was electro-deposited under an intense magnetic field. CdTe is less affected by magnetic field, because of its cubic structure, but Cd or Te has hexagonal structure, which is sensitive for magnetic field. In this paper, crystal orientation of Cd or Te film, which can be utilized as basic layer for CdTe deposition, will be developed.

Jan 1, 2006

By Luben Savov

This paper presents recent research works on the removal of the tramp elements Cu, Sn, Zn and Pb from steel. The evaporation of Cu and Sn in iron-based melts treated at reduced pressure of the gas phase was studied in a vacuum induction melting furnace. The effect of chamber pressure, temperature and melt composition was investigated. Since the main source of contamination of steel with Sn and Zn is the recycling of tinplate and zinc coated steel, respectively, possibilities for the removal of meta1ic coatings in a scrap pre-treatment stage were studied, too. Tin was removed in the temperature range 400-5S0°C by treatment with reactive gases featuring high sulphur potential. Zinc can be removed by evaporation or by a combination of thermal and mechanical treatment. The paper discusses the thermodynamics of Pb in carbon-saturated iron melts, too.

Jan 1, 2001

Many studies have been conducted over the past 3 decades on the leaching of gold in solutions containing thiosulfate, ammonia and copper. However, most of these studies have been carried out using ore samples, with very few fundamental studies of this system being attempted. The majority of the published studies have failed to acknowledge the undesirable side reaction between copper(H) and thiosulfate, let alone account for its effect. The fact that the solution chemistry is constantly changing makes it very difficult to perform a fundamental study of gold leaching. With the advent of the rotating electrochemical quartz crystal microbalance (REQCM), such fundamental studies are possible as this instrument measures mass in real time. This has allowed leach kinetics to be measured in a matter of minutes and hence at essentially constant solution conditions; The present paper highlights that a sufficient concentration of copper(II) and ammonia are required in order to achieve appreciable gold leach rates. However, the use of air (oxygen) to maintain the copper(Il) concentration catalyses the undesirable copper(II) reaction with thiosulfate. The presence of ammonium ions is shown to have an effect on this undesirable reaction as well as on the gold leaching ?reaction. Preliminary electrochemical studies into .gold electrowinning using the REQCM show that gold(I) thiosulfate cannot be readily reduced to metallic gold in the potential region at which cementation usually occurs. However, it is well known that gold cementation onto copper occurs rapidly. The current study addresses this discrepancy by studying the effect that copper and silver have on the reduction of gold thiosulfate. It has been found that the presence of both silver and copper enhance gold deposition, particularly at low over potentials. While this is beneficial in cementation, the presence of copper and silver in solution has been found to cause passivation of the cathode surface during electrowinning at 'higher overpotentials.

Jan 1, 1998

By Wayne Bell, Xiaodi Huang, Matthew Andriese, Jiann-Yang Hwang, Zhiwei Peng

"The equations for determining microwave field attenuation length and half-power depth in magnetic materials were derived from Maxwell’s equations. The microwave field attenuation length and the half-power depth for a magnetite concentrate were calculated and the temperature dependence of them was determined. It is demonstrated the microwave field attenuation length and the half-power depth highly depend on temperature and decrease with increasing temperature up to 900 °C. The variations of field attenuation length and the half-power depth with temperature indicate the microwave power attenuates much faster than the field strength in materials. The evaluations of field attenuation length and microwave half-power depth can be used to characterize the microwave dissipation behaviors in the sample and optimize the dimensions of the material in microwave heating.IntroductionMicrowave has been applied in materials processing for its distinguished advantages including rapid heat transfer, volumetric and selective heating [1,2]. However, most research work involving microwave heating are confined to non-magnetic materials (e.g. ceramics), with limited attention paid to the heating of mixed property materials (e.g. magnetite and other ferrites) under microwave irradiation [3-5]. Since many magnetic materials exhibit good and even better microwave absorption capability than non-magnetic counterparts, it is quite necessary and deserved to take advantage of this property and then improve the heating efficiency. To achieve this aim, further understanding on the microwave heating mechanism, especially the microwave propagation/dissipation behaviors in magnetic materials is required.The dissipation behavior of microwave in materials has been identified as one of the key factors that affect the efficiency of heating under microwave irradiation and this behavior can be characterized by several parameters. Apart from traditional penetration depth (TEM power penetration depth, Dp = 1/(2*a), where a is the TEM field attenuation factor), two other parameters, field attenuation length (Df) and half-power depth (Dh), are also applied to indicate the microwave dissipation in materials [6].The accurate determination of such parameters can help in optimizing the dimensions of the load in a microwave furnace, producing more uniform heating under microwave irradiation and avoiding thermal runaway."

Jan 1, 2011

By H. P. Wang, E. M. Perry

"Analytical solutions for investigating the solidification of casting problems with initial superheat and natural boundary conditions have been derived using an integral method. There are two moving interfaces in the solution field, one for the phase change line and the other for the superheat line. Two coupled nonlinear differential equations, representing two moving layers, were calculated by the Runge-Kutta numerical integration scheme. The solutions are in terms of six dimensionless parameters: phase change number, two Biot numbers for interfaces, diffusivity ratio, and dimensionless superheat temperature and time. Parametric studies on these parameters have been conducted to provide generic information about this phase change problem. This analytical information is extremely useful for validating numerical solutions. A simplified I-D finite element model was constructed for the purpose of comparison. The excellent agreement between the analytical and finite element solutions has proven that they are mutually validated.This validated finite element modeling tool was then used for modeling an investment casting process of a super-alloy with a simple geometry: a two-step plate. The nonlinear latent heat release, a common property of alloy materials, was approximated by several piecewise linear segments. The transient temperature response of this 2-D finite element solution, including a metal/mold gap resistance, shows excellent agreement with experimental data.This fundamental work provides a solid basis for further work on the development of a process modeling tool for the complex investment casting process.IntroductionAt present, the investment casting process is used in a variety of industries. In the aircraft engine industry, in particular, investment casting is used to produce parts ranging from turbine blades to engine frames. Because a large single casting can replace many component parts that require machining, fabrication, and assembly, this one-piece casting approach becomes a very cost-effective manufacturing process.The main constraint in using this process for mass production is the long design-to-production lead time. The standard rigging design is still an art, based on the experience of casting experts, rather than on scientific methods. Many trials are often required before making a sound final casting. In order to .reduce the number of expensive casting trials, the development of computer-aided tooling technology is needed.The fundamental physics describing this manufacturing process can be simply described. They reduce to a solid/liquid phase change problem, with two parts - first, the thermal balance of the initial superheat temperature of the molten metal and the preheat temperature of the ceramic shell through heat conduction, and second, the energy release from the mold surface to the ambient by radiation."

Jan 1, 1986

By K. Moriyamo

Operation improvement efforts at Hyuga Smelting Co., Ltd. have focused on calcining capacity in the reduction rotary kilns ("the kilns"), whose limited feed rate capacity had capped production at around 18,000t-NiN since 1995. To improve the kilns' feed rate capacity of 80 wet t/hr, attempts were made to increase the gas flow in the kilns by increasing the capacity of the off-gas fans. However, as the increased gas flow resulted in only limited improvement of the kilns' feed rate, a scoop feeder was installed on each kiln to add coal to the middle of each kiln's interior to gain a higher efficiency of thermal supply and conversion. With these gas flow and coal charge addition operations, the kilns' feed rate capacity increased up to 120 wet t/hr, with burner fuel efficiency increasing by approx. 10% (approx. 5% in total with the additional coal included). As a result, production was raised to a level of 22.000t-Ni/Y Keywords: reduction rotary kiln, scoop feeder, additional coal charge.

Jan 1, 2004