Search Documents

By John J. Jonas, Sang-Hyun Cho, Ki-Bong Kang

"The recrystallization behavior of Nb micro alloyed steels containing Cr, Mo, Ni and Ti. was studied using hot torsion testing with the aim of modeling the recrystallization processes and the mean flow stress taking into account the microstructural behavior during hot rolling. The kinetics of static and metadynamic recrystallization were characterized and appropriate expressions were formulated for the recrystallization kinetics. These are shown that the recrystallization kinetics depend on steel composition and the processing conditions. The stress-strain curves were determined in order to derive new equations for the peak stress, peak strain, mean flow stress and softening kinetics. The peak strain is influenced by the presence of alloying elements; their addition, which has a solute drag effect, retards the rate of grain boundary motion, shifting the peak to the right. The addition of Nb to the steel results in a significant increment in the activation energy for hot deformation, and Mo has smaller effect than Nb, but Cr has the opposite effect. It was also found that the deformation activation energy in these steels was not altered by the addition of Ni. The rate of metadynamic recrystallization increases with strain rate and temperature and is observed to be independent of strain, in contrast to the observations for static recrystallization.The mean flow stress (MFS) calculations, based on the Sims analysis, are then compared with the predictions of a model based on an improved Misaka mean flow stress equation in which solute effects, strain accumulation, as well as the kinetics of static and metadynamic recrystallization are accounted for. Good agreement between the measured mean flow stresses, which is obtained from the mill logs of POSCO Kwangyang #3 HSM (hot strip mill), and 'predicted ones is obtained over the whole range of rolling temperatures. The results demonstrate that dynamic recrystallization followed by metadynamic recrystallization, supported by the unexpected load drops, sometimes occurs for the rolling schedules studied in the present analysis."

Jan 1, 2001

By Jan G. H. du Preez, C. Viviers, B. J. A. M. van Brecht, H. E. Rohwer, Nicole M. Sumter

"At the basis of metal ion separation lies some particularly metal ion specific chemical property which lends itself towards exploitation. This could be in the form of an anionic complex or a neutral chelate complex. In the former a cationic centre with a particularly high affinity for the complex will have to be designed. In the latter case a stereospecific chelate ligand containing the correct symmetry and type of donor atoms will have to be designed. In both above cases the ""active centre"" can be entered in a from that it can function in different media of hydrophobicity, eg a precipitant, a resin or a solvent extractant. Recent results obtained in this laboratory will be used to illustrate how the above variables can be exploited to develop improved processes for the separation of base metal and platinum group metals.IntroductionThe separation of metal ions in hydrometallurgy can be performed broadly speaking with two major aims. Firstly the separation/removal of a certain group of metal ions, either as a means of preconcentration or as a removal from effluent as part of a purification process and, secondly the removal of a specific metal ion from an industrial stream in order to produce a specific metal in a pure form. This latter operation is by far the most difficult of the two and is becoming more so in the light of the fact that the world is moving in the direction of lower grade ores and increasing pollution. Such a process can be divided into three essential parts, firstly the molecular one in which an active centre is required to obtain specificity, secondly a matrix within which this active centre must function, i.e. as part of a resin or solvent extractant and thirdly the design of the total system to optimize the realization of the operation."

Jan 1, 1996

By Takahiro Miki

Soldering material widely used is Sn-Pb alloy, which have low melting point and excellent electrical, strength properties and wettability. However, Pb is one of the toxic elements, which is undesirable due to environmental and safety reasons, thus Pb-free alternative alloy is preferred for new soldering material. Sn-Ag and Sn-Zn based alloys have been viewed as very promising candidates, among many potential substitutes. Addition of third element to these alloys will decrease melting point of the alloys. Hence, Sn-Ag-In and Sn-Zn-Mg alloys are expected to be suitable for replacing Sn-Pb solder alloy. In order to design new Pb-free soldering materials, it is crucial to understand precise thermodynamic properties and phase diagrams of alloy systems. In the present work, ion current ratios of Ag to In and Mg to Zn were measured for Sn-Ag-In and Sn-Zn-Mg alloys by mass spectrometry, respectively. Also, the authors reviewed the thermodynamic properties of terminal binary alloys determined by other researchers and evaluated a thermodynamic functions to express the excess Gibbs free energy of each binary alloy. Thermodynamic functions to express the excess Gibbs free energy of liquid Sn-Ag-In and Sn-Zn-Mg ternary alloys were determined, utilizing the assessed Gibbs free energy of terminal binary alloys with the measured ion current ratios using mass spectrometer.

Jan 1, 2003

By B. Yawney

A copper-nickel sulfide concentrate was leached in water at about 2000C under oxygen pressures of about 0.35 MPa. Oxidation of sulfide to sulfate was virtually complete in about 30 minutes, resulting in greater than 95% copper and 98% nickel extractions. Leaching temperature was shown to be the most important factor affecting metal extractions. Measured rates of oxygen consumption were used to develop batch kinetic data. Mini-plant continuous pressure leaching tests agreed with batch leach results. A proposed overall flowsheet is briefly examined.

Jan 1, 1976

By A. M. Blount

In 1983, a final ruling of the U.S. Occupational Health and Safety Administration (OSHA) specified that chemicals containing >0.1 % of a carcinogenic substance or > 1 % of a substance hazardous to health must be labelled. Amphiboles of the fibrous or asbestos-type must be quantified at levels of 0. I % whereas the status of non-fibrous types is not finally determined at this time. Tremolite and actinolite can possibly be measured to 0.1 % by XRD, but anthophyllite cannot be so measured. Recently the International Agency for Cancer Research (IARC) has designated quartz as a suspected carcinogen, and its quantity must be measured to the 0.1 % level. Thus, it has become Increasingly important to be able to detect and quantify minerals in bulk samples down to low or "trace" levels. It has been found that minerals needing to be quantified can often be concentrated by microcentrifuge and counted by means of polarized-light microscopy. For example, amphiboles in talc samples can be separated by using a heavy liquid (thallium formate-malonate) of density 2.810. Talc floats, and amphiboles sink. After centrifuging, the denser particles are removed from the bottom with a Pasteur pipette and placed in a clean centrifuge tube. Distilled water is added to the tube containing the denser minerals and the tube centrifuged again. After several washings with distilled water, the sample is removed along with a drop of water to a clean glass slide. A drop of 1 .584 refractive index liquid and a cover glass are placed over the dried sample. The slide is scanned for particles greater than 5 um in length and having an aspect ratio greater than 1:3. These are checked for refractive index, sign of elongation and extinction angle to differentiate them from talc particles on edge and other minerals. Amphiboles have all indices greater than 1.584, and talc has all indices equal to or lower than this value. Alternately the heavies at the bottom of the centrifuge tube can be filtered through a nucleopore filter. After the filter has been washed with distilled water and dried, a 1.584 refractive index liquid renders the filter transparent in two of the four extinction positions so that a count of amphibole particles can be made directly on the filter. The refractive index-density method which is so useful for talc powders should be equally useful for other nonsoluble industrial minerals.

Jan 1, 1989

By Blas Melissari, Stavros A. Argyropoulos

"In this paper a computational approach was employed to estimate the melting of solid spheres immersed in different liquid metals and under different convective conditions. The spheres are made from the same material as the liquid metal. The SIMPLER algorithm was implemented using a three-dimensional system in Cartesian co-ordinates. Experimental validation of the dimensionless correlation was carried out in two fluids with vastly different Prandtl numbers. The dimensionless heat transfer coefficient (Nusselt number) is obtained as a function. of the Reynolds and Prandtl number.IntroductionThere is a paucity of dimensionless convective heat transfer correlations applicable to fluids like liquid metals. The existing correlations cover single Prandtl number metals [l] or at most two different Prandtl number metals [2]. A knowledge of heat transfer rates from particles at high flux levels has become increasingly important to the design of energy transfer systems. Melting of solid particles has been studied extensively as it relates to many engineering and environmental applications, such as materials processing, space applications, water resource and energy conversion. When objects are immersed in a fluid with a temperature higher than their melting point, they melt and produce molten material that then mixes with the surrounding fluid. These objects experience not only size variation but also changes in their shape. This observation is more pronounced when the melting occurs in a forced convective flow.Yuge performed pioneering experimental work on the heat transfer from a sphere to air under mixed convection [3]. He suggested procedures for predicting the Nusselt number. Hieber et al [4] studied the spherical system analytically, but their study was limited to flow with small Reynolds numbers. Many researchers studied the melting dynamics of ice spheres in water at different convective regimes. Aziz et al [5] and Hao et al [6] performed measurements of the heat transfer coefficient in the water system by measuring the melting time of ice spheres in forced convection. Hao et al [7] performed visualization studies of ice spheres melting in water under mixed convection regime. All of this groundbreaking work, however, did not involve the use of liquid metals"

Jan 1, 2004

By Richard L. Summers

The shaped charge has proven in various military and industrial applications to be an effective penetrator of materials. Upon initiation a detonation wave traverses the explosive billet, collapsing a metallic liner and creating a jetting process. From multiple non-simultaneous flash radiographs of the jet in free flight, the observer can study the collapse, formation, and growth of a shaped charge jet. Digitization of a particulated jet's position and shape from the radiograph into electronic storage files provides the experimentalist with an efficient basis for data reduction. With the aid of a simple personal computer, one can in a matter of minutes generate a wealth of information concerning jet formation after initiation and thus gain insight into the quality of its manufacture, design, and assembly. This paper will in detail explain the methods in place for fully automated data reduction of radiographic films. Methods of computer aided digitization of particulated jets and analysis of physical jet characteristics and performance will be discussed.

Jan 1, 1992

By M. E. Karabin, R. J. O'Malley

"A mathematical model of the roll casting process has been developed which predicts macro-variables, such as roll separating force, roll torque, and strip exit speed for a range of roll speeds. Continuum variables, such as interface pressure, interface shear stress, freeze-front shape, and internal temperature distribution are also predicted.The model consists of two independent segments: solidification and rolling. The solidification model is two-dimensional (thickness and rolling direction) and is capable of handling alloy solidification. The solidification model is employed until solidification through the thickness is complete, then the rolling solution is activated.The rolling model is a one-dimensional (rolling direction) mechanical solution based on the von Karman approach, coupled with a two-dimensional thermal solution. The flow stress is expressed as a function of the average through-thickness temperature of the strip.Experiments were performed using a laboratory roll caster to test and refine the model. Experimental strip exit temperatures were used as input to the model. Experimental and predicted roll torque and strip exit speea were forced into agreement at a single reference roll speed to obtain values for the coefficient of friction and the interfacial heat transfer coefficient. Using these values, good agreement was obtained between predicted and experimental torque and strip exit speed over the entire range of roll speeds examined."

Jan 1, 1986

By Batric Pesic

Adsorption of gold on activated carbon from gold bromide solutions was examined as a function of pH, particle size, carbon amount, initial gold bromide concentration, bromine concentration, temperature, and various cations and anions. pH did not have any effect below pH=6. Above pH=6, pH had dramatically negative effect. The adsorption results satisfied a first reaction order model. The reaction rate constant was proportional to the inverse of carbon particle radius. It was also proportional to the amount of carbon, and independent of initial gold concentration. Temperature had a very little effect at pH=l. At pH=8, the activation energy was a function of the extent of a reaction, increasing with the extent of a reaction. Cu, Fe, Ca, Mg, and Na cations and sulfate, chloride and bromide anions did not have any effect on gold adsorption. Bromine had a very negative effect on gold uptake.

Jan 1, 1991

By Mark William Kennedy

"Electric furnaces containing high quantities of slag are applied in many areas of pyrometallurgy, often for smelting or slag cleaning. A variety of ratios or rules of thumb have been employed in the industry for the dimensioning of these vessels, in most cases with no clear technical basis.In this paper, several design guidelines are presented (electrode size, spacing, vessel dimensions, energy intensity, etc.) as an attempt to provide some technical basis for optimal dimensioning.Furnace heat generation is related to side wall copper cooler heat losses, in an attempt to establish a methodical design strategy particularly for minimum electrode to wall spacing for modern furnaces with cooled linings.Issues regarding the true nature of heat production in a slag furnace are discussed with regards to the possible impact on accurate modeling and design.IntroductionSlag furnaces have passed through a number of design 'generations' characterized by increasing energy intensities, improved electrode technologies and advancing development in their physical structure or 'furnace integrity' as shown in Table I f 1]. A 3rd generation furnace using ultra-high-power (UHP) graphite electrodes is shown in Figure 1, as a generic example of the types of physical structures present in modern slag furnace designs [1]."

Jan 1, 2012

By Batric Pesic

Gold dissolution with bromine was studied by using the rotating disc technique. Geobram TM 3400 was used as a source of bromine. The parameters studied were: rotating speed, Geobrom 3400 concentration, pH, temperature, sulfuric and hydrochloric acid concentration, and the concentration of various cations (copper, iron, zinc, aluminum, manganese, potassium and sodium) and anions (chloride, bromide, sulfate, nitrate, and iodide) According to the Levich plot and activation energy, gold dissolution was controlled by a chemical reaction rate. Copper, iron, and manganese in their highest oxidation states, aluminum, zinc, sodium and potassium did not have any effect on gold dissolution rate. The presence of manganous ion dramatically decreased the gold dissolution rate. Kinetic performance of bromine, in the form of Geobram TM 3400, was compared with performance of cyanide and thiourea.

Jan 1, 1990

By I. Gaballah

High and low grade concentrates of tantalum and niobium oxides were obtained by leaching a medium grade tin slag. Chlorination and carbochlorinalion of these concentrates were studied between 200 and 1000 "C. Chlorination or carbochlorination of the low grade concentrate led, at 1000 OC, to the extraction of about 95 % of the tantalum and niobium oxides. However, the tantalum and niobium chlorinated compounds were contaminated by iron and manganese chlorides. Complete extraction of the niobium and tantalum pentoxide was achieved during the carbochlorination of the high grade concentrate at 300 and 500 "C, respectively. While chlorination of this concentrate at 1000 "C, allowed to the volatilization of about 60 and 80 % of Ta205 and Nb205. In both cases, condensates were composed of almost pure tantalum and niobium chlorinated compounds. The results demonstrate the advantages of the lixivialion based on the "pseudo- structure" of the raw tin slag to obtain the high grade concentrate. The conclusions of this work suggest that the carbochlorination of the high grade concentrate is an efficient process for the extraction of refractory elements from tin slag.

Jan 1, 1993

By Zhang Jianliang, Xu, Zuo, Runsheng, Haibin, Kexin, Jiao

Full oxygen blast furnace iron-making is one of the new technologies, which is most likely to realize large-scale application. In this paper, based on the technology of full oxygen blast furnace, the reduction behavior of pellets is studied systematically by using the analytic method of non-isothermal dynamics on the different atmosphere(CO,H2) and the dynamics model of gas-solid reduction reaction is constructed, which lay the foundation of reduction model establishment of full oxygen blast furnace burden. The result shows that the time of pellets which began to react is delayed with the increase of the content of H2. When the temperature is between 650 'C and 1050 'C, the content of H2 in the reduction atmosphere is larger, and the rate of the reduction pellets is larger. The reduction rate changes at 780 'C, and a certain amount of H2 in the reducing atmosphere will significantly improve the reduction reaction when the temperature is above 780 'C. Non-isothermal reduction behavior is controlled by interfacial chemical reaction and internal diffusion under high reduction potential. H2 ratio in reducing atmosphere increased from 0% to 100%. The reduction reaction of the apparent activation energy decreased from 49.03kJ-mor1 to 33.74kJ·mor1.

Jan 1, 2013

By Zhou Jiemin

A mathematical model is developed to determine the economic thicknesses of refractories and insulations in rectangular furnaces, Both the heat loss cost and the lining investment are taken into account to achieve a minimum operation cost. For the sake of calculating the heat flux, the paper is particularly concerned with the simulation of the three-dimensional transient heat conduction processes in the lining and a Douglas-Rachford method is used to solve the finite difference equations, The model has been used to design an industrial electric resistance furnace operated periodically. the values of temperatures and power consumption measured from the furnace correspond with the model results.

Jan 1, 1991

By J. K. Brimacombe, I. V. Samarasekera, B. G. Thomas

"Mathematical models have been developed for the processing of static cast steel ingots and are app1ied to investigate the mechanisms for the formation of panel cracks. Panel cracking is an intermittent but persistent defect that causes affected steel ingots to be scrapped. A two-dimensional, finite-element, heat-transfer model was formulated and employed to calculate the temperature distribution in both large and small steel ingots during the various processing stages from initial casting to the start of rolling, including solidification, cooling in the mold and in air, reheating in the soaking pit, and subsequent air cooling. The stress state in the ingot arising from the calculated temperature variations was then determined. This involved the development of a transient, elasto-visco-plastic, finite element, thermal stress model, including the effects of phase transformation volume changes and kinetics creep, and temperature-dependent, mechanical properties. The results of the mathematical model predictions of temperature and stress were then used to determine the mechanisms and to suggest solutions for two different types of panel crack formation. Mid-face panel cracks apparently form during air cooling when the mid-face surface temperature is between the Arl and 500~C. Off-corner panel cracks appear to initiate internally during the early stages of reheating but do not propagate to the surface until much later. IntroductionPanel crack formation in static-cast steel ingots is a defect that has been plaguing the steel industry for several decades. Although the problem is intermittent, it is also serious since affected ingots must be scrapped. Panel cracks are manifested as two distinct types of cracking problems. ""Mid-face"" panel cracks are found exclusively in small, 2 to 6 ton, medium carbon steel (0.3 to 0.7% C) ingots and usually exhibit a single, continuous, longitudinal crack down the center of one of the ingot faces as shown in Fig. l (l). ""Off-corner"" panel cracks often form roughly oval, discontinuous crack patterns on the wide faces of large, 20 to 30 ton ingots as seen in Fig. 2 (2). They affect only low carbon steels (0. l to 0.2% C) with high manganese content. Both defects affect only aluminum-treated steels and are caused by a combination of intermediate temperature ductility loss involving aluminum-nitride precipitation and thermal stress generation. The ductility problem has received a good deal of attention which was the subject of a recent review (3). The present study was undertaken to investigate the thermal stress aspects of the problem through the development of mathematical models of heat transfer and stress generation in static-cast steel ingots. The ultimate objective was to elucidate the mechanisms of formation for both types of panel crack and to evaluate possible solutions to the problem."

Jan 1, 1986

By Lei Wang, Xiancong Zhao, Hongxu Li, Lifeng Zhang

Recovery of Fe from red mud has been studied using statistically designed experiments. The effects of three factors, namely: reduction temperature, reduction time and proportion of additive on recovery of Fe have been investigated. Experiments have been carried out using orthogonal central composite design and factorial design methods. A model has been obtained through variance analysis at 92.5% confidence level.

Jan 1, 2015

By Jackson Jenkins

The second survey of world copper SXEW plants has been completed. Solvent extraction and electrowinning data published in 1996 has been updated and leach data from seventeen plants is now included. The following pages list the results of the thirty- two plants that responded to the survey. Selected information is summarized in graphical form.

Jan 1, 1999

By Raghavan Srinivasan, Y. V. R. K. Prasad, William G. Frazier, Steve C. Medeiros

"Aerospace gas turbine disks operate in an environment of relatively high stresses caused by centrifugal forces and elevated temperatures. These severe conditions necessitate the need for materials with good high temperature strength and low cycle fatigue resistance. One class of alloys used for this task is the nickel base superalloys, out of which, lN 718 is the most widely used in the aerospace industry [I]. The properties of IN 718 are attributed to the combined effects of the chemistry, heat treatment, and microstructure. The chemistry is tailored not only for solid solution strengthening but also for precipitation hardening developed during heat treatment, which combined with a fine grained microstructure lead to excellent mechanical properties such as low cycle fatigue resistance and elevated temperature strength. The properties of a gas turbine disk are sensitive to the microstructure, in particular the grain size, which is dependent on the processing history. The ability to precisely control the microstructural development during forging is dependent on controlling the process so that the workpiece is deformed within a ""safe"" region where no microstructural damage or flow instabilities occur. The microstructural mechanisms during deformation may themselves vary within the ""safe"" region and it is desirable to determine them within the range of parameters that are commonly used in industrial processing. The objective of this work is to establish a relationship between the grain size and the process control parameters i.e., temperature and strain rate, in the hot working of IN 178.BackgroundIN 718 belongs to a class of nickel-iron base superalloys with a face-centered cubic (FCC) austenitic matrix strengthened by precipitation of ordered intermetallic or carbide precipitates and is a nickel-rich alloy strengthened by ordered body centered tetragonal (BCT) precipitates, Y"". The alloying of nickel and iron results in the formation of the austenitic matrix, y, while the addition of chromium and molybdenum cause solid solution strengthening. Also, alloying with niobium causes precipitation of the metastable hardening constituent Y"" (Ni3(Nb,Ti)). Extended aging treatments in the temperature range 650 °C - 980 °C allow the more stable orthorhombic 8 phase (Ni3Nb) to form. Trace amounts of boron are also added to serve as grain boundary strengtheners for high temperature creep resistance. Hot deformation of IN 718 is performed between the Y"" and 8 solvus temperatures to facilitate recrystallization and to control grain growth. While deformation below the Y"" solvus (""""962°C) produces no change in grain size, deformation above the Y"" solvus but below the 8 solvus will lead to a dynamically recrystallized microstructure. The presence of the 8 precipitates will pin the grain boundaries after recrystallization and restrict grain growth so that a fine grain microstructure is obtained. Deformation above the 8 solvus ("""" 1038°C) will lead to a microstructure which has undergone grain growth during deformation."

Jan 1, 2000

By Jennifer Murphy, Brad S. Schake, Karol Holmes, John R. FitzPatrick, Mike H. West

"The separation and purification of uranium from either nitric acid or hydrochloric acid media can be accomplished by using either solvent extraction or ion-exchange. Over the past two years at Los Alamos, emerging programs are focused on recapturing the expertise required to do limited, small-quantity processing of enriched uranium. During this period of time, we have been investigating ion-exchange as a method for extraction/purification of uranium from acidic media. In addition, waste stream polishing is associated with this effort in order to achieve more complete removal of the uranium prior to recycle of the acid. Extraction chromatography has been demonstrated to further polish the uranium from both nitric and hydrochloric acid media thus allowing for a more complete recovery of the actinide material and creation of less waste during the processing steps.We will discuss contact experiments for evaluation of eleven different resins for uranium removal from nitric acid, the evaluation (again by contact experiments) of uranium elution from the ion-exchange media by various chemicals, and small-scale experiments for the removal of 235U from nitric acid. Larger-scale (1 DO-gram) flow experiments, using depleted uranium, were done after the small-scale evaluation of the selected resin. A discussion is also included concerning the shortcomings of the contact experiments and how the flow experiments were modified in order to overcome these problems. We will also discuss the application of ion-exchange for some specific process needs at Los Alamos.Contact experiments were used to evaluate some commercially available solvent-impregnated resins in addition to evaluation of several resins of this type synthesized in our laboratory. These experiments involved both nitric and hydrochloric acid media. The data from these experiments will be used to determine the column size and amount of resin required to polish the waste stream produced by the ion-exchange process described above. Small-scale flow experiments will be described and data given on the mass balances achieved using this two step process.Future work for evaluation of new ion-exchange and solvent-impregnated resins as well as the search for new eluants will be discussed. Other future experiments for both processes, including large-scale experiments, will be discussed in detail."

Jan 1, 1996

By William Brinkman, Mark Jolly, Nasim Soleimanian, Karl Dearn, Oliver Brinkman

"Glass manufacturing is a heat intensive process. There is a direct correlation between the batch distribution techniques and the furnace energy consumption, productivity, and quality of the glass manufactured. All four major segments (float, container, fibre, and specialty glasses) would benefit from using an optimised batch distribution technique where possible. Oscillating batch chargers (OBC) have been in use since the early 70s, despite their superior batch shape, coverage, and in turn positive effects on the energy consumption and productivity of the furnace they are almost exclusively used in container glass manufacturing. The OBC’s main difference compared with other charging methods is its ability to directly influence the batch initial velocity. This paper reports on results achieved in CFD models (GFM) used to study effect of the machine on the overall energy consumption in the doghouse and the melt space.IntroductionGlass manufacturing can be divided to four major segments float glass, container glass, fiberglass, and specialty glasses. The financial cost of manufacture, its impact on the environment, lack of standardisation and mounting pressure imposed by the authorities for reduction in emissions means that the industry and its suppliers are utilising CFD modelling in order to tackle these challenges. The need for high temperature to create and maintain the viscous flow, homogenisation of the glass melt, and maintenance of the process to allow continuous output of glass of the right quality are the contributors to the energy intensive activities that are involved in continuous glass manufacturing. This in turn has resulted in design of large container glass furnaces which have high energy consumption, low specific performance, and high CO2 emissions where the most efficient furnaces in the container glass sector have a specific primary energy consumption of 3.8 GJ /tonne of glass at a level of 50% cullet in the batch making even very small improvements in efficiency by operation optimisation a value adding activity [1-14].The theoretical calculated energy required to melt glass is 2 to 3 times less than the energy actually used to melt glass as a result of glass melt passing a zone 5 to 8 times before leaving the tank.[8]. This causes contamination as the result of mixing between the completely molten glass free from bubbles returning to the batch area where there is freshly molten non-homogeneous glass, still containing very large numbers of bubbles and un-molten batch. At high temperature some components are dissolved rather than melted. Given that an un-molten batch is a good thermal insulator, it can be transported a long way into the furnace, increasing the need for homogenization which also increases the glass residence time of glass melt. This is why large unbroken strings of batch should be avoided, as should an overall blanket without gaps."

Jan 1, 2014