Search Documents

By A. Bieg, M. Samson, Z. Bell, A. Zinsser, J. Schuyler

As the world progresses toward the renewable energy transition, the demand for minerals increases exponentially. According to the International Energy Agency (IEA) 2021 Net Zero by 2050 Report, critical mineral production needs to grow six times to combat climate change. It’s estimated that four to seven percent of global greenhouse gas (GHG) emissions come from the mining sector’s Scope 1 and 2 (direct and indirect) emissions. Including Scope 3 (upstream, downstream, and embedded) emissions, the sector accounts for 28% of global GHG emissions. In a typical mining operation, diesel fuel is the biggest source of direct GHG emissions, and haulage is often the main source of diesel emissions. Large haul trucks have been the industry standard for over 50 years and offer flexibility, relatively low capital cost (especially with equipment lease options), and guaranteed technology with known maintenance. The challenge will be to justify their continued use when there are more economical options that lead to significant reductions in GHG emissions. The purpose of this study is to compare five haulage options in terms of GHG emissions, using the methodology defined by the Greenhouse Gas Protocol Scopes 1, 2, and 3 (Category 2). Additionally, this analysis compares operating and capital costs associated with the five haulage options (emerging and proven technologies): 1) Diesel-Electric Haul Trucks, 2) Battery-Electric Haul Trucks, 3) Fuel Cell Haul Trucks, 4) Railveyor, and 5) Conveyor. This analysis looks at the emissions and costs associated with operating the equipment (fuel and electricity), the embedded emissions and costs associated with the construction and installation of the equipment itself, and the associated infrastructure (roads, powerlines, and rail).

Feb 1, 2023

By Jr. Goller

You and I can visit cement plants, inspect the various rotary kiln systems and find some equipment or some burning techniques that waste energy--fuel and power. After we have made such a visit and studied a few ideas, we could recommend ways to eliminate much of this waste. Probably every idea would cost money to bring into action. For our discussion, let us arbitrarily set an upper limit of $1,000,000 on the recommendations that we are allowed to make. Call these "low-cost" or "short-term" measures. They are improvements that do not require more than say, three months to complete; they do not require a major revision to the process. Other recommendations are "high-cost" or "long-term"; they are outside the scope of this discussion. Some of our "low-cost" recommendations would offer a satisfactory return on the money that they cost; the remainder would not. Now, is there some way that we can rather quickly pick out the "low-cost" measures that will show a satisfactory return and spend our time making these improvements first? Can we separate these items from those where the return is less likely to be good? I feel that we can pick some of these items quickly if we have a kiln system that has consistently non-uniform day-to-day operation. If the operation is uniform we probably cannot pick them quickly.

Jan 1, 1977

Semisoluble salt minerals are characterized by their ionic bonding and are distinguished from soluble salt minerals by their limited solubility in water. One group of semisoluble salt minerals being considered is the alkaline earth salt minerals, including fluorite (CaF2), calcite (CaCO3) and apatite (Ca5F (PO4)3), as well as celestite (SrSO4) and barite (BaSO4). Another group of semisoluble salt minerals being considered is the rare-earth salts, which include bastnaesite ((Ce, La) CO3F), monazite (CePO4) and xenotime (YPO4). Surface chemistry features of these selected semisoluble salt minerals are discussed with respect to flotation separations. First, the surface chemistry features of alkaline earth semisoluble salt minerals are reviewed, and then the surface chemistry features of rare-earth semisoluble salt minerals are examined. The discussion includes electrokinetic behavior, wetting characteristics and collector adsorption.

By J. H. Howard

The purposes of this report are to summarize the findings of the Committee on the Challenges of Modern Society Non-electrical Project (a working committee of the North Atlantic Treaty Organization) and also, thereby, to provide an introduction and review of the current situation regarding non-electrical applications to those who are interested in the subject.

Jan 1, 1975

By P. K. Kaiser, M. Cai

When designing an efficient and effective support system for burst-prone ground, it necessary to select the most appropriate, i.e., the ‘right’ support components, including areal and reinforcement components. For this paper, it is assumed that the areal support is not the weakest link and the support performance is controlled by the rock reinforcement and holding components (bolts). We discuss the loading modes of rockbolts under static and dynamic loadings and analyze published data from laboratory and field tests. The mechanisms of energy absorption of dynamic rockbolts are presented and rockbolts are categorized based on factors such as energy absorption capacity, energy absorption rate, direct and indirect energy absorption capacities, rock mass bulking or displacement control, and shearing resistance capacity. Guidelines for selecting the ‘right’ rockbolts to build an effective rock support system for burst-prone ground are provided.

Apr 26, 2022

By B. Pesic

The recovery of silver and gallium from flue dust with acidified thiourea solutions was examined. The studied parameters were temperature, particle size, thiourea concentration, acid concentration, and the presence of oxidants. The study of the extraction of these two metals was undertaken in sulfuric acid medium. Silver dissolution was dependent on all examined parameters, whereas gallium extraction was only dependent on the initial acid concentration. The experimental results suggest a new very efficient method for recovery of both silver and gallium. Almost complete recovery of silver and gallium can be accomplished within 90 minutes. A technological scheme for recovery of both metals is also proposed.

Jan 1, 1986

By C. D. Iles

The philosophy used in designing and writing Duval's Sierrita mine design programs is discussed. The Sierrita Incremental Design system (SID) is reviewed with emphasis on Pushback Extraction Design (PED). FED is a method by which predesigned pushbacks are sequenced into an optimized period-by-period design that can be directly utilized in daily operations as well as intermediate and long range planning. The advantage of SID is that it provides a practical, mineable open pit design. PED is not a theoretical design system; it is in operational use.

Jan 1, 1981

By Mohammed Sakr

The empirical relationship between torque measured during installation and pile capacity has gained a wide acceptance in the helical pile industry in the last few decades. This paper presents a theoretical model developed to estimate torsional resistance of cohesive soils to helical pile installation. The proposed torsional resistance model was then used to establish torque factor, Kt, a factor that is widely used in the industry. The results of the study indicated that the Kt factor is a function of the load path (i.e. tension or compression), pile geometry and soil properties. The assessed Kt factors in tension and compression were validated by the results of 74 installation records and full-scale helical pile load tests. A parametric study was also performed to qualitatively assess the relative importance of different parameters that affect the Kt factors.

Aug 1, 2013

By A. D. Ajak

A complete mining cycle involves digging, loading, hauling and dumping of the materials. Moving the ore from the pit to the crusher or to the waste dump requires access routes, which are termed haul roads. These roads have to be designed, constructed and maintained. A review of the literature indicates a common consensus among researchers that there should be a balance between haul road economics and safety of the road users. However, there is no universally accepted theory on the design of haul road geometry and, in particular, road dimensions. The current industry practice is based on empirical data and rules of thumb developed by engineers. Therefore, this paper will use the overlooked and less valued branch of mathematics, arithmetic progression, to derive a road width equation. It is beyond the scope of this paper to discuss all road design components. The focus will be on the geometric aspects, which more often have a direct impact on road safety. In this paper, the current design practices and techniques for haul road geometrics design will be explored, using arithmetic progression to formulate road width equations, case examples to apply the equation and then validating the results with conventional techniques that have confirmed the reliability of road width equations, thus eliminating use of tables during design.

Jan 1, 2012

By R. S. Kalyoncu

Materials demands by the advancing process technologies, desire for higher performance and durability, and improved efficiency in combustion processes, such as applications in heat engines, heat exchanges, and batteries have added to the driving force fueling R&D efforts for the development of components with the combined characteristics of metals and non-metals. These new materials involve refined and specialized microstructures that can lead to improvements in the performance characteristics and durability new technological applications require. Fabrication and sintering methods, once believed to be sufficient, alone, have been found to be inadequate in the manufacture of such advanced components. Realization of the importance of the starting powders has led to efforts to produce materials of ultrahigh purity and ultrafine particle size with very narrow particle size distributions. Such powder characteristics are essential for the fabrication of components with high density and with the desired mechanical, electrical, or magnetic properties called for by the specific application. Novel ultrafine and ultrapure powder preparation techniques are discussed and effects of impurities on the powder characteristics, particle size and morphology, sintering behavior and properties of the finished product are elucidated.

Jan 1, 1992

By Louis A. Panek

Using an approach based on the theory of similitude, the author develops a general equation and related concepts that provide new insights to an old problem. The load-bearing capacity (strength) of a square, rectangular, or cylindrical prism of a brittle material such as rock, coal, or concrete is expressed as the mathematical product of a size effect, a shape effect, and a function of the mechanical properties (deformability, cleat/joint spacing, and friction) of the pillar, roof and floor materials. Through an application of multivariate statistical analysis, the results of assorted tests and observations of failed pillars can be combined into a fundamental scaling equation, which provides a unified, consistent approach to the estimation of mine pillar strength. The form of the equation is sufficiently general to be able to incorporate refinements in the characterization of the basis factors, as they become available through future experimentation and analysis.

Jan 1, 1979

By SUHAINA ISMAIL, NORLIA BAHARUN, SHAIK ABDUL RAHMAN, WAN NUR SYAFIQAH ANUAR, MOHAMMAD REZAEI ARDANI

Hypochlorite leaching system is a strong oxidizing solution for metal sulfides, which are naturally associated with gold extraction. This study evaluated the hypochlorite leaching of refractory gold ore by using the response surface method–central composite design (RSM-CCD) as a statistical approach in determining the optimum condition of gold extraction from refractory gold ore. The studied parameters for the gold recovery were pH (4 to 6), concentrations of Ca(OCl)2 (0.5 to 1.5 M) and NaCl (2.5 to 3.5 M) in the solution. It was found that the maximum gold extraction of 82.46% (13.85 g/t) was achieved at a pH of 4.0 with NaCl and Ca(OCl)2 concentrations of 2.93 M and 1.08 M, respectively. The statistical analysis also revealed that the amount of gold recovery in chloride solution was significantly depended on pH as the main factor, followed by concentrations of Ca(OCl)2 and NaCl.

Jan 8, 2021

By Vishwajeet Ahuja, Benoit Jones

"INTRODUCTION Shotcrete lining forms an integral part of conventional tunneling and is widely applied for underground excavations. Early strength gain of the shotcrete is a crucial aspect for ground support and safety of operatives. Strength requirements are dependent on various factors such as lining thickness, ground type, excavation size and tunnel depth. The early strength gain is typically monitored using destructive tests, such as needle penetration, stud driving or coring samples for uniaxial compressive strength testing in the laboratory. Being destructive, these tests cannot be directly performed onto the lining without causing damage that must be repaired, which is a particular problem for permanent linings. For this reason and to avoid the need for operatives to work near to exposed ground and/or fresh shotcrete, these destructive tests are often performed on panels, which are sprayed at the same time as the tunnel lining. All current testing methods are also very local, testing only a small part of the lining or a panel, which may not be representative because the temperature history could be significantly different. Therefore, these tests do not provide an accurate or complete picture of the lining strength gain. New testing methods that are non-destructive and can scan the whole lining remotely would be extremely desirable. This paper describes a new method, using thermal imaging techniques, that achieves these aims. It also discusses the real-time on-site application of the method, providing insight into the experience gained and conclusions derived. Shotcrete Shotcrete used for tunnel linings requires immediate strength development. The strength development is a direct result of the hydration reaction of cementitious materials present in it. A progressive sequence of the hydration reaction changes it from a solid suspension (typically referred to as fresh concrete) to a solid skeleton with a porous network and thereafter, into a solid with predominantly discontinuous pores (Byfors 1980). In the case of shotcrete, early strength is needed to support the self-weight and then continuing early age strength gain is required to begin to support ground loads. These strength requirements, along with other workability needs, are met by careful concrete mix design, the use of admixtures, such as accelerator and superplasticizer (BS EN 934-5 2007), and supplementary cementitious materials, such as silica fume."

Jan 1, 2016

By Shannon Seitz, Qingwen Shi, Junfeng Pan, Shuwen Wang, Brijes Mishra, Shaohong Liu

Delayed coal bursts in deep coal mines have caused significant fatalities and economic losses in recent years. Instead of occurring right around the advancing face, this particular type of coal burst is characterized by its occurrence at a certain distance behind the advancing face. To better understand the mechanism of a delayed coal burst, we used borehole camera, electromagnetic CT, and borehole deformation monitoring device to observe the fracturing and deformation process of an advancing entry’s surrounding coal in the field. Borehole camera detection showed a zonal disintegration phenomenon in the advancing entry’s surrounding coal. Electromagnetic CT detection showed that zonal disintegration developed within 14 days of excavation. Borehole deformation monitoring indicated a deformation rate difference between the intact zone and fractured zones. The deformation rate difference was observed to increase with time and cause increasing elastic energy accumulation in the intact zone. The cumulative elastic energy in the intact zone finally caused a delayed coal burst in the entry. Sensitivity analysis of the cumulative elastic energy was conducted based on a thick-walled model deduced from field detection. The model shows that the smaller thickness of the intact zone brings higher elastic energy in the intact zone. This investigation provides an improved understanding of delayed coal bursts in deep coal mines.

Oct 19, 2021

By Luttrell. G.

The profitability of coal mining operations is highly dependent on the performance of the coal blending and processing facilities. Many companies have recognized this fact and have instituted optimization programs that require large amounts of coal characterization data, extensive operational information and complex costing models. Unfortunately, this brute force approach to optimization is often overwhelming in terms of time and cost and is generally too inaccurate to be of value in day-to-day field operations. A simpler and more practical approach involves the use of ?micro-price? optimization throughout the coal supply chain. This fundamental concept assigns unit values to each type product (particle or groups of particles) passing through the production units. True optimization occurs whenever all particles with positive worth are recovered and passed to market, while all particles with negative worth are rejected. This paper describes the fundamental workings of the micro-price concept as applied to coal blending and processing operations. Several examples are also included to demonstrate the economic gains that can be realized via the application of this concept.

Feb 23, 2014

By K. Darcovich

The wettabilities of agglomerates made from coals of several different ranks were measured by the adhesion technique. Oil levels from 0 to 10% by weight were used. As was expected, it was found that higher-rank coals are more easily oil-wetted and that the surface properties of the agglomerates correlate with agglomeration recovery and ash removal data.

Jan 1, 1992

By Sah Rameshwar, T. Umadevi, K. S. SRIDHARA

In the magnetite iron ore pelletization process, oxidation of magnetite followed by sintering of the oxidized magnetite (hematite) is desirable. Optimum preheating time & temperature and roasting time & temperature is required to get the desired properties of the pellets with magnetite, hematite, and hematite–magnetite blend. In order to utilize the magnetite resources in a current induration furnace, which is designed for hematite resources, detailed pelletization studies have been carried out to optimize the firing cycle for magnetite concentrate as well as magnetite with hematite concentrate. Under optimum conditions, such as preheating temperature 1000–1150 °C, preheating time 10 min, roasting temperature 1250 °C and roasting time 7.5 min, the cold compression strength (CCS) of magnetite roasted pellets was 325 kg/p, and this was due to recrystallization of secondary hematite particles, and development of the strong slag bond between primary and secondary hematite particles. The strength of hematite concentrate pellets was 260 kg/p. From laboratory studies, it was found that without disturbing the induration furnace firing cycle, which is designed for hematite ore ~5%, magnetite concentrate can be used along with hematite concentrate in pellet blend and the strength of the pellets was 270 kg/p. As the magnetite concentrate increases in the blend beyond 5%, the preheating zone residence time should be increased or a supply of extra oxygen is required. Laboratory as well as plant investigation has shown that the addition of magnetite to the hematite mix blend improved the strength of the pellets compared to hematite pellet alone.

Oct 26, 2020

By Alexander Karim

This paper reviews the growth pattern in bauxite and alumina production, and primary aluminum smelting through 1980. Because the alumina and primary metal are intermediate products of the major integrated aluminum companies, it is not possible to determine their production costs. The costs indicated in this paper are order of magnitude costs based on published figures and the market price of these products. The conclusions in this paper indicate the general pattern of growth in the aluminum industry and are not meant to be a substitute for the feasibility and economic studies that are needed for individual bauxite mining, alumina refining and aluminum smelting projects.

Jan 1, 1968

By Richard C. Travis, Edward C. Dowling

A detailed kinetic study of the flotation installation at the Metcalf Concentrator revealed a rougher flotation circuit operating under less than optimal conditions. Based on these results, a project was initiated to approximately double the rougher flotation capacity by increasing the installed volume from 780 cubic meters to 1,560 cubic meters. This project, which was completed in early 1991, replaced the existing cells with larger capacity cells. A comprehensive analysis of results demonstrates significant metallurgical benefits. INTRODUCTION/BACKGROUND The Metcalf Concentrator is located in Morenci, Arizona and is part of Phelps Dodge Morenci, Incorporated. Sumitomo Metal Mining of Arizona is a minority partner in the operation with 15% interest. The Metcalf Concentrator is the newer and smaller concentrator and operates in conjunction with the Morenci Concentrator. Operating capacity at Metcalf is currently 48,000 TPD of ore on a 365 days per year basis. The Metcalf Concentrator was commissioned in 1974 at a 30,000 TPD operating rate for the purpose of treating ores originating in the Metcalf Mine. The mine takes its name from the former town of Metcalf which was named for Robert Metcalf who was credited with discovery of the mineral district. The predominant ore mineral is chalcocite which occurs as a secondary enrichment closely associated with iron pyrite. The host rock is largely granodiorite and quartz monzonite. The original rougher flotation circuit consisted of a total of six rows of Wemco 8.5 cu. meter (300 cu.ft.) flotation machines treating pulp from the two grinding sections (Sections A and B). Each row was configured in a 4-4-4 arrangement. Shortly after startup the throughput rate was increased significantly without sustaining a recovery loss. This increase was achieved by raising the target value for the particle size of the cyclone overflow which is the rougher flotation feed. Shortly thereafter, the capacity of the pump and cyclone began to restrict further increases in throughput. After testing, two 66 cm. (26-in.) cyclones and a 12-in. X 12-in. centrifugal pump replaced the original classification equipment. As a result of these modifications, the grinding section could routinely process in excess of 42,000 TPD. Due to the increased tonnage rates, limitations in the rougher flotation circuit performance were observed. In an effort to improve the performance of rougher flotation with this higher throughput, the speed of the flotation mechanisms was increased from 230 RPM to 250 RPM. This change improved the suspension of the coarser feed and induced additional air into the pulp. It did, however, apply additional strain to the motors, shortening their life. At these elevated processing rates, it was found that the dart valves operated almost entirely at the top end of the control range and could not efficiently handle upsets from the grinding section. This was remedied by lowering the end overflow weir and allowing some of the tailings to overflow the end weir. However, in order to obtain acceptable recovery levels, the flotation pulp was maintained at a high level, adversely influencing the rougher concentrate grade.

Jan 1, 1993

By G. V. Campbell, O. T. Holdsworth, M. G. Nelson

A senior design project is required by all accredited mining engineering degree programs. Often referred to as the capstone of a student’s education, this project is expected to include all the important components of the preliminary economic assessment of a mineral prospect, including orebody modeling, grade and reserve estimation, selection of mining and processing methods, preliminary mine design, access and utilities, environmental compliance and reclamation, and financial analysis. Two of the authors (Campbell and Holdsworth) completed a senior project in 2021. They analyzed the Akie zinc deposit located in Canada. This paper summarizes the economic analysis portion of that project. The two primary objectives of this economic analysis were risk reduction and integration of economics and engineering. Addressing risk is important as risk is one of the primary concerns in mining investments. Risk reduction was the primary concern through the entirety of this economic analysis. Integration of financial analysis and engineering design was the first component of a risk reduction design. This allowed for financial and engineering design to be optimized in conjunction with one another. This produced benefits from both a financial and an engineering prospective. From a market, economic, and financial risk perspective, risk was reduced by forecasting multiple metal price scenarios, and then addressing the Akie project’s economic viability at each price point. Lastly, risk was address through consideration of nontraditional financing options. The project also sought to minimize financial and human capital risk, by proposing mutually beneficial cooperative social relationships and favorable work, schedules. Description of that work is not included in this paper.

Mar 2, 2022