Search Documents

By J. T. Carlson

Dolomite [CaMg(CO3)2] is an intolerable impurity in phosphate ores, due to its MgO content. The need to develop a cost-effective method for the removal of dolomite from high-MgO phosphate ores becomes increasingly important as high-grade reserves become depleted. The jigging process has been investigated as a method for the beneficiation of phosphate ores. A laboratory-scale jig was constructed and tested using a semicontinuous, ?through-the-screen? jigging process. Two types of sedimentary phosphate ore were used; a sample from Plant 1 in the 4.00 x 0.85-mm size range, containing 1.55% MgO, and a sample from Plant 2 in the 3.40 x 0.85-mm size range, containing 3.07% MgO. These were tested, using previously optimized jigging parameters, at high and low feed rates. For the Plant 1 phosphate ore, a phosphate concentrate that contained 0.89% MgO was achieved with a bone phosphate of lime (BPL) recovery of 32.0%. For the Plant 2 phosphate ore, a phosphate concentrate that contained 1.38% MgO was achieved, with a BPL recovery of 74.7%. Minimum achievable MgO grades were also determined by analyzing hand-separated phosphate samples.

Feb 1, 2012

By Syd S. Peng, C. Y. Chen

Introduction The Surface Mining Control and Reclamation Act was passed in 1977 to put an end to the uneven environmental standards and enforcement established by various coal mining states in the US. One year after passage, the Secretary of Interior was directed to promulgate permanent program regulations implementing Title V provisions of the Act. These regulations were to form the basis for state regulatory programs under the Act and to allow states to assume primary regulatory responsibility. To implement the underground mining provision of the Act, the Secretary is directed in section 516(a) of the Act to promulgate rules. But they must take into consideration the differences between surface and underground coal mining. The regulations developed by the Secretary in 1979, with respect to subsidence control, included: • a subsidence control plan as part of the permitting process; • substantive provisions establishing performance standards for subsidence control; and • provisions providing for the prohibition of mining under perennial streams, impoundments larger than 24.6 dam3 (20 acre ft), and certain public facilities and urban areas. Industry challenged the Secretary's regulations implementing the subsidence control provisions. The litigation was consolidated with all other challenges to the permanent program regulations. (Permanent Surface Mining Regulation Litigation, Civil Action No. 79-1144; D. D.C., May 16, 1980.) In two opinions dealing with the multitude of issues raised by both industry and environmental groups, the US District Court of the District of Columbia ruled against industry. It upheld the promulgated subsidence control provisions. The US Court of Appeals stayed the appeals pending the agency's review and revision of its regulations. The regulatory reform was conducted in accordance with the order from the Secretary of Interior and the President in 1981. As a result, the subsidence control regulation was revised, reproposed, and finalized in June 1983 (Federal Register). This regulation, along with others, was again challenged by environmental groups and industry. On Oct. 1, 1984, the court, after finding the Secretary's reading of the Act reasonable, upheld the 1983 subsidence regulation except for one section. On Feb. 21, 1985, in accordance with the court's ruling, the Office of Surface Mining (OSM) suspended a portion of 30 CFR 817.121 (c)(2) concerning the damage correction requirement for structures or facilities and reproposed it on July 8, 1985 (Federal Register). In conjunction with a request for public comments, OSM now also seeks comments on the omission from the 1983 rule of the requirement in the 1979 rule regarding a presubsidence survey and monitoring of damage to structures. Technical issues related to subsidence regulations The subsidence regulations of June 1, 1983, consist mainly of two parts: a subsidence control plan as part of the permitting process; and substantive provisions establishing performance standards. The latter also includes provisions for prohibiting mining under certain areas. Under subsidence control plan section 784.20, minimum require-

Jan 2, 1986

By J. A. Botín

NPV is a static measure of project value which does not discriminate between levels of internal and external risk in project valuation. Due to current investment project?s characteristics, a much more complex model is needed: one that includes the value of flexibility and the different risk levels associated with variables subject to uncertainty (price, costs, exchange rates, grade and tonnage of the deposits, cut off grade, among many others). Few of these variables present any correlation or can be treated uniformly. In this context, Real Option Valuation (ROV) arose more than a decade ago, as a mainly theoretical model with the potential for simultaneous calculation of the risk associated with such variables. This paper reviews the literature regarding the application of Real Options Valuation in mining, noting the prior focus on external risks, and presents a case study where ROV is applied to quantify risk associated to mine planning.

Jan 1, 2012

By Gary Almeraris, Vincent Jr Tirolo

Traditionally, “Means and Methods” were the sole responsibility of Contractors. However, because of a number of litigious projects in the 1970s, Owners and their Engineers began including Suggested Methods of Construction (SMC) in Contract Drawings. By the late 1990s these SMCs were becoming baseline “Means and Methods” with Contractor recommended changes often considered as Value Engineering proposals. By 2004, the word “Suggested” was sometimes changed to “Prescriptive.” Owners are also purchasing TBMs and other mining equipment for Contractors prior to bid. Is limiting the contracting community’s innovation in developing their own “Means and Methods” and selecting their own equipment in the best interests of the Owner? Does it reduce the Owner’s, Engineer’s or the Contractor’s risk? Are claims reduced and finally what is the impact on the bid? A questionnaire was sent to more than fifty senior engineering field and management personnel representing more than 30 heavy construction companies to ask their opinion on these questions.

Jan 1, 2005

By Frank A. Jerabek

Problems of mine backfilling and fill material deposited underground, the characteristics and relationship between the deposited fill material and overlying ground, and the practical applications and limitations of hydraulic backfilling as ground support are discussed. A great variety of materials ranging from coal washery refuse to concentrator tailings is used as hydraulic fill. Some materials will solidify and cement; others will resemble quicksand, Hydraulic fill as ground support is more efficient in inclined mine openings than in horizontal mine openings, where it cannot be placed tightly to the back. This and other deficiencies of hydraulic backfilling led to the development of pneumatic stowing. Research work in hydraulic backfilling at the Pennsylvania State University is also discussed. This research work includes the investigation of segregation in the discharged fill slurry, the quantity of solids escaping in the drain liquid, the relationship of escaping solids to slurry concentration and discharge rate, and the compressibility of fine fill material.

Jan 1, 1965

Tracer gases are an effective method for assessment of mine ventilation systems, but their dispersion characteristics can differ substantially as ventilation parameters, such as flow path and velocity, vary. This research utilizes Computational Fluid Dynamics (CFD) to model a simplified full scale model mine, details a sensitivity study examining mesh size for an underground coal mine simulation, and examines gas dispersion parameters to determine the optimal model methods for simulation of tracer gases in underground coal mines. These models can be used to determine how a given tracer gas profile might be generated in a mine or areas of a mine that are not accessible, for example, immediately following a mine disaster. Accurate simulation scenarios can allow for the remote determination of the status of the ventilation network, but the sensitivity of the simulation at mine scale must be carefully examined.

Jan 1, 2012

By Steve Kral

Borates are minerals that contain boron. Trace amounts exist in rocks, soil, water and people. Boron-containing ores are rare and U.S. Borax, a subsidiary of Rio Tinto Borax, controls one of the world’s two world-class borate deposits. Through its global systems of mines, refineries, ports, sales offices and distribution centers, the company supplies nearly 45 percent of the world’s demand for borates. Borax has been mining borates in California for more than a century. This year the company celebrated 131 years of continuous business in the Golden State and 76 years at its operations in Boron, the site of California’s largest openpit mine. It also has mines and refineries in Argentina, refineries and ship-ping facilities in Europe and technical staff in the United States, North and South America, Europe and Asia Pacific. So, with the 130±years of borate mining and processing experience behind it as well as its global marketing and distribution centers, there is very little that Borax does not know about borates.

Jan 1, 2003

By M. K. Mohanty, H. Akbari, L. A. Ackah

Dry separation was the predominant method of coal cleaning in the United States from the 1930s to 1980s. The application peak of dry separators for cleaning raw coal was in 1965, when about 23.1 Mt of cleaned bituminous coal was produced. The main advantage of dry coal cleaning is the elimination RIWKH GHZDWHULQJ VWDJHV DQG VLJQL¿FDQWO\ UHGXFHG moisture in comparison to wet processing. In addition, developed dust control systems have made dry cleaning method an environmentally friendly process. The largest air-based coal cleaning plant was built in Pennsylvania in 1968 and could clean 1,272 t/h of raw coal sized smaller than 19 mm. This was followed by a decline in dry coal cleaning to less than 3.6 Mt in 1988. Some of the main reasons that shifted coal operations IURPGU\WRZHWSURFHVVLQJZHUHWKHQHHGIRUPRUHHI¿FLHQW separations with lower density cuts, increase in raw coal surIDFHPRLVWXUHVSHFL¿FDOO\LQXQGHUJURXQGPLQLQJWRFRQWURO GXVW ¿QHUSDUWLFOHVL]HUHTXLUHPHQWV LQFUHDVHLQ¿QHVLQUDZ coal from underground mines, and health and safety concerns related to dust and noise (Arnold, Hervol and Leonard III, 1991; Miller, 2011).

Introduction Some people say it is almost impossible to get mining permits in California. Some say the day of the lone mining entrepreneur is past. And some say you cannot make money mining gold where old-timers have already mined it, especially in Tertiary gravels. But a young mining operator and SME member, Tim Callaway, is proving these ideas wrong. Callaway's company, Brush Creek Mining and Development Inc., has the necessary permits for its Gardner's Point gold mine in Sierra County, CA. And, Callaway has secured funds for the 7.7 km'/d (10,000 cypd) Tertiary gravel operation. The company's initial goal is to produce 373 to 466 kg/a (12,000 to 15,000 oz per year) of gold at Gardner's Point mine at a cost of less than $6.43/g ($200 per oz). Feasibility studies are currently being conducted to consider product levels up to the 1555 kg/a (50,000 oz per year) involving additional plants and infrastructure. While exploring for other hard-rock properties, the Brush Creek company already operates the Brush Creek lode gold mine. The mine sits high on a ridge south of Goodyear's Bar, which is located on the North Yuba river. It might be noted that the Brush Creek mine has been the subject of media stories recounting how a mine can operate with sensitivity to the environment. Gardner's Point project In 1983, Callaway negotiated with the Gardners Point Ltd. Partnership for control of the Gardner's Point property. The Partnership had been engaged for three years in securing permits, mapping and drilling, and test mining. The Partnership actually mined about 43.5 dam3 (57,000 cu yd) of gravel, which yielded 25.2 kg (810 oz) of free gold. Later, the Brush Creek company acquired ownership of the property. The company then began its own exploration and development program. As underground development proceeded at the Brush Creek mine, plans matured for a high-volume operation at Gardner's Point. Australian and English investors contacted Callaway. A joint venture was negotiated. The Australian owners became majority participants; the Brush Creek company, a minority participant and the operator. The Australian investors agreed to contribute $3.5 million (60%) to the Brush Creek Joint Ventures. The Brush Creek company will contribute its expertise as well as assets and liabilities valued at $2.3 million (40%). About $2 million has been allocated to the Gardner's Point project. Later, Brush Creek Mining and Development Inc. sold 50.4% of the company's common stock to English investors for $5.4 million. Callaway negotiated this private placement, which permits further exploration of projects being investigated. Geography and history The Gardner's Point mine is located in the northern Sierra Nevada of California, about 9.6 km (6 miles) east of the little town of La Porte in Plumas County. The mine lies high on a ridge above Slate Creek, which divides Plumas and Sierra Counties. La Porte is accessible from the Sacramento area by a winding, paved, two-lane highway. But the mine is reached only by two different unpaved county and Forest Service roads. Both roads include steep grades in and out of the Slate Creek canyon. Mine elevation is about 1.4 km (4600 ft) above sea level. The area is thus threatened by occasional heavy winter snows, though it

Jan 3, 1987

The 2003 SME Annual Meeting and Exhibit will take place Feb. 24-26 in Cincinnati, OH. The meeting will feature a host of special symposia and programming geared toward the industrial minerals and aggregate industry sectors. This programming focus is particularly relevant for this annual meeting, as it will be hosted in the center of America’s transportation hub and industrial mineral center. Cincinnati, located on the Ohio River, is key to the movement of America’s supplies and construction material needs.

Jan 1, 2003

By Shemek Oginski

The 5 km (16,194 lf) of 6.1m (20 ft) diameter TBM driven tunnel built by the J.F.Shea Co. will serve as sewage overflow storage. The TBM tunnel and four connecting tunnels excavated by drill and blast methods in hard granite will remain unlined. Based on the Geotechnical Baseline Report (GBR), the Contract documents provided a design with no required pattern of rock bolts, no probing, no pre-excavation or consolidation grouting, and lastly, no final lining of the tunnels was deemed necessary. This paper will provide a general overview of these topics with the emphasis on the actual ground conditions encountered versus the projected conditions provided in the GBR and how the GBR reflected the design of the project. Proposed modifications to the temporary and permanent ground support will be presented and the necessity of probing and pre-excavation grouting will be evaluated.

Jan 1, 2005

By D. Loring, J. Almgren

Climax Molybdenum Company’s Henderson Mine is a large panel caving molybdenum mine located about 43 miles west of Denver, Colorado. Three Joy M120-72-880 fans are installed in parallel on the No. 1 exhaust shaft. Throughout the mine’s history, ventilation changes such as the completion of the No. 5 exhaust shaft have decreased the utilization of these fans. To optimize fan performance they have been run with the full complement of 16 blades, down to as few as four blades. Since the completion of ventilation upgrades associated with the Henderson 2000 project, one surface fan has been operated under normal conditions with 10 or 12 blades. With the completion of a new network model of the Henderson ventilation system, a tool was built to develop fan curves for possible future fan configurations and predict future fan performance. This paper describes the tool and its use at Henderson.

Jan 1, 2007

By B. J. Dave, Ashok J. Desai, Allen J. Hulshizer

This paper presents various design and construction considerations involved in developing an underwater installation of lined, large diameter shafts not known to have been previously accomplished for the diameter size, depth or ground conditions identified with the Seabrook Power Station. Outlined approach provides for driving tunnels independent of shaft sinking operation, permits the use of prefabricated shaft lining and incorporates a safe dry tap method for connecting the shafts to the tunnels. INTRODUCTION The Seabrook Power Station, located two miles inland from the Atlantic Ocean, at Seabrook, New Hampshire, is a two unit, nuclear powered, electric generating plant, each unit having a capacity of 1150 megawatts (electric). Typical to all steam driven generators is the requirement for large quantities of water. Requirements for the Seabrook Plant will be met by intaking and discharging approximately 850,000 gpm of ocean water at a considerable distance from the shore line in water depths that render the environmental impact inconsequential. Obtaining, conveying and discharging such large quantities of water represents a major undertaking, particularly under today's environmental controls. Tunnels are well suited to reducing the environmental impact at the Seabrook site by conveying the water about 250 feet deep under the salt marsh (a valuable ecological feature) and under the beach well out into the ocean without any noticeable ground surface disturbance. An alternate approach utilizing trenched piping would have created some disturbances and was environmentally less desirable. The tunnels connect to intake and discharge

Jan 1, 1976

"Tell us how you got involved in mining?I was first exposed to mining at a young age, as a consequence of my dad and his passion for the industry and rock collecting. Even though he graduated with a degree in mining engineering from Washington State University, my dad spent most of his career working as a structural engineer for the Boeing Company. At the time, Boeing supported a range of employee activities and clubs, including one devoted to mineral prospecting, small-scale dredging and rock hounding. My dad was extremely active in the Prospectors Club, where as a family, we spent a good part of my youth tramping around the Pacific Northwest digging for mineral specimens and panning for gemstones and gold. On my mother’s side of the family, I had relatives that mined in Dawson City and Fairbanks, AK which left a family legacy of sorts. I loved the stories that my dad and a close buddy of his, who was a geologist, would tell about various operations and towns, as well as the wild times at the annual Northwest Mining Association (NWMA) meeting in Spokane, WA. My first recollection of ever being at a commercial operation was during a tour of the Bunker Hill Mine with my dad when I was 7 or 8 years old; this had to have been shortly before the May 1972 fire at Sunshine. That visit of the mine and processing facilities made a permanent impression on me. While I always knew there was something special about the Silver Valley, I began to understand why. To this day, I still get the same feeling when I visit historic mining districts like Leadville, Morenci, Virginia City, Butte, Silverton and Barkerville. During our summer excursions to Helena, MT to dig sapphires, we would usually make visits to Butte and watch mine operations inside the Berkley Pit and surface activities at the Kelly and Mountain Con. In high school, I did well in math and science and began entertaining thoughts of pursuing a degree in engineering. Above all, I wanted to go to a college in the West that had a good academic reputation, where I could also play football. As a 6-ft, 190-lb nose guard, my options for a Division I scholarship were pretty slim, and there weren’t that many technical schools in the Northwest that were Division II that offered athletic scholarships. As fate would have it, I was unexpectedly contacted by Marv Kay, a legendary coach at the Colorado School of Mines (CSM), and was recruited to play ball. Fortunately, I had a couple of high school friends who were already attending CSM, and I had just secured a summer internship with Asamera Minerals in Wenatchee, WA. It was as if all the stars had aligned, and, with the support of my parents, I made the decision to attend Mines. Despite the stress of getting through CSM during a period when the mining industry was in freefall, it was a great decision to attend Mines, and I’m thankful for all the opportunities, friendships, and faculty mentoring I received as a student"

Mar 1, 2019

The failure of a seal in an underground coal mine can have devastating consequences. Traditionally seals have been constructed as flat walls. Large hydraulic dams, on the other hand, are constructed as concave arches. This paper presents an initial analysis of the potential strengthening of seals by concave construction as well as the impact of additional cost in terms of labor and material. A simple finite element analysis of three-dimensional solids under uniform loading allows comparisons between the strength of a flat wall and a curved arch. The models are examined for reasonable behavior and displacements at 20, 50, 100, and 200 psi loads.

Jan 1, 2007

By Angela Binder, Mareike Schubert, Yichen Jiang, Sandra Nowosad, Oliver Langefeld

GermanyINTRODUCTIONThe mining industry is currently characterized by various factors such as environmental impact, resource scarcity, social responsibility and geopolitical uncertainty. The production of minerals required to meet the demand for renewable energy is expected to increase by 500 % by 2050, particularly for critical minerals such as graphite, lithium and cobalt 1. Easily accessible deposits are often depleted, meaning that deeper and more complex deposits need to be developed. Furthermore, investors’ value systems have shifted towards more sustainable practices. Alternative approaches to solving this problem are therefore currently being developed, such as the Modular Mining Systems concept for scalable and adaptable mining projects 2. Many mining companies have also taken important steps to become more sustainable, implementing measures such as proactive closure strategies, restoration programs and the development of renewable energy projects. In the European Union, laws such as the Critical Raw Materials Act and the Net Zero Industry Act support the mining industry 3,4. They see it as important for the energy transition and promote more sustainable ways of working in the industry Particularly negative environmental impacts such as land degradation, scarcity of local water resources, water pollution and greenhouse gas emissions are ingrained in society’s memory. Despite these efforts, the public image has not yet changed. To change this perception, the industry must strive to better communicate its sustainable practices and the steps it is taking towards a more responsible and sustainable future, promote transparency and build trust.Digitalization, automation and electrification are driving the digital transformation in mining. However, their implementation can lead to higher capital expenditure, limiting their adoption across the industry. Furthermore, implementing new technologies can be a daunting task for any organization. Change management comes into play when introducing such disruptive technologies. It involves preparing an organization for change, potential resistance and establishing effective communication. This helps to ensure that the implementation is successful and the benefits of the new technology are maximized. Digital transformation requires well-trained, young mining, electrical, mechatronic and software engineers with a deep understanding of information systems. Unfortunately, the industry faces the enormous challenge of attracting this younger generation, who have little interest in the extraction of raw materials. The need for action is compounded by an aging active workforce heading into retirement and the forecast of increasing demand for critical minerals.In this challenging environment, the concept of Blue Mining with its constant further developments represents a promising approach. This implies a shift from a linear to a sustainably oriented circular economy. For the mining industry, this specifically means the introduction of innovative technologies, the increased recovery of materials from waste and the consistent questioning and application of circular principles along the entire life cycle of a mine. Such a change can not only reduce the environmental impact, but also contribute to economic resilience and increased social acceptance of mining.

Feb 1, 2025

By Faruk Oksuz, Clay Haynes, Miguel Sanchez, Patrick Finn, Roger J. Maurer

The Milwaukee Metropolitan Sewerage District’s (MMSD)’s challenges of basement flooding and wet weather sewer overflows are being creatively addressed with the Northwest Side Relief Sewer tunnel. The $132 million, 20-foot diameter, and37,740 feet long conveyance and storage tunnel excavation in dolomite at depths reaching 165 feet below ground surface has been successfully completed within13 months in April 2004. This paper includes Owner’s perspective on the overall project, and the design and construction details by the Designer and the Contractor. The project contract documents included a comprehensive Geotechnical Data Report and the Geotechnical Baseline Report.

Jan 1, 2005

By P. A. C. De Ruiter

The Lower Cretaceous salt deposits of the Gabon Basin and Congo Basin were said down on ton of an Burly Cretaceous Lato Jurassic, continental graben fill that represent!) the rifting phase of the Afro-American continent. The salt 13 characterized by high percentages of potash and magnesium salts and the scarcity of sulphates and carbonates. The salt probably originated from a brine that was already enriched in high-soluble salts before entering the Gabon Congo basins. Their low-solubility equivalents are found in the Cuanza Basin of Angola. Commercial mining of the potash salt is only possible in those onshore areas where it is essentially undisturbed, shallow and of the right chemical composition. These conditions are net in Congo where the Holle mine produces from rich sylvinite deposits.

Jan 1, 1978

By M. Dobbins

The advent of the more efficient and effective rare-earth roll (RER) separator in the early 1980?s began a new era of dry magnetic separation. The RER units quickly became the separator of choice within the materials processing industry. Though RER separators are now commonplace throughout the world, only modest advancements have been made to the original design. This paper details recent, more significant, rare-earth magnetic separation developments. These developments maintain the best features of existing technology while minimizing shortcomings. The discussion includes discerning features that aid in better metallurgical performance. Also discussed are improved mechanical aspects that allow for both easier operation and maintenance. Performance details from various test programs are included.

Jan 1, 2009

By David Hopkins, Steve Klein, Bradford Townsend, Ed Sum, Derek Penrice

INTRODUCTION The Transbay-Caltrain Downtown Extension (DTX) Project involves the construction of an approximately 1.5-mile rail line that will extend Caltrain commuter service and the future California High Speed Rail system into downtown San Francisco. The underground rail extension will be constructed by mined tunnel and cut-and-cover methods. Tunneling challenges include difficult ground conditions, low rock cover, the presence of historic buildings along the alignment, and the large tunnel span, ranging from approximately 50 to 65 feet. Three mined tunnel construction methods were evaluated: the Stacked Drift Method, the New Austrian Tunneling Method/Sequential Excavation Method (NATM/SEM), and Tunnel Boring Machines (TBM). This paper describes the challenges presented within the mined tunnel section, and summarizes the evaluation of tunneling methods that led to the selection of NATM/SEM. PROJECT OVERVIEW The existing Transbay Terminal opened in downtown San Francisco in 1939. This facility is antiquated, and does not meet current building seismic safety standards or the transportation needs of the Bay Area. For these reasons, San Francisco voters approved Proposition H in 1999, which proposed to construct a new or rebuilt regional transit center at the site of the existing terminal and extend Caltrain commuter rail ser-vice to the new transit center. The new transit center is the hub of the Transbay Transit Center (TTC) Program, which will greatly enhance regional transit service by providing connectivity for six Bay Area transit providers at one facility. The program will be the largest inter-modal centerwest of New York City. The TTC Program is comprised of two major projects, the Transit

Jan 1, 2007