Search Documents

By John Freer

A colloquium on solid-liquid separation was held by The South African Institute of Mining and Metallurgy on 23rd September, 1982, at the State Pavilion Auditorium, Milner Park, Johannesburg, to co-incide with the Electra Mining Exhibition. It was attended by about 150 delegates. Eight papers were presented covering: Geostatistics The School of Earth Sciences of Stanford University, the Centre de Geostatistique ofthe Paris School of Mines, and the Department de Genie Mineral of the Ecole Polytechnique of Montreal are cosponsoring the organization of a 2nd NATO ASI (North Atlantic Treaty Organization Advanced Study Institute), under the name of 'GEOSTAT TAHOE 1983', to be held at South Lake Tahoe, California, on 4th to 17th September, 1983.

Jan 1, 1982

By P. Kohler, T. D. Sampson, T. H. Tunley

The Metsep Process for the separation and recovery of zinc, iron, and hydrochloric acid from spent pickle liquors by T. H. TUNLEY, B.Sc. (Ch em. Eng.) (Visitor), P. KOHLER (Visitor), and T. D. SAMPSON, Pr. Eng., B.Sc. (Chem. Eng.), B.Econ. (Visitor) A spray roaster has been installed in the Johannesburg area for the treatment of spent liquors from a variety of small pickling operations. A new process was developed for the processing of the liquor that is contaminated with zinc chloride, and a commercial plant was built incorporating this process. An ionexchange plant separates the zinc from the iron chloride, and a liquid-liquid-extraction plant converts the zinc chloride to zinc sulphate and recovers the hydrochloric acid.

Jan 5, 1976

By A. M. Copeland, A. J. Barrett

The use of hydraulically placed backfill in the deep gold mines of South Africa has increased rapidly over the past decade. The backfill that is delivered to the placement areas has a relatively high moisture content, and it is therefore pumped into geotextile containment bags that allow excess water to drain out but retain solid particles. The specific problems associated with this process that are addressed in this paper include the loss of solid particles entrained in the excess water, the rate of strength gain of the backfill, and the post-placement shrinkage of the backfill. The results of laboratory, surface stope, and underground tests are described. The parameters that were varied included the slurry density, the particle-size distribution, and the feed rate of the slurry the concentration of added flocculant; and the type of geotextile used as containment. Suggestions are given for the optimization of the placement properties of backfill.

Jan 1, 1994

By A. V. L. Narasimham

The practice of refractory lining in Fe Cr furnaces is purely based on the behavior of various refractories used in different parts of the Furnace at elevated temperatures. The choice of the pattern of lining is mostly done on traditionally based concepts. Refractory Lining of a furnace is the most crucial enabler for operational excellence for Ferro Alloys production. During the last few years, no major technological change has taken place in ?Refractory Lining Management?, only freeze lining concept is becoming popular. Many ferro chrome furnaces today, have the refractory lining problems especially at tap holes, resulting in shutdowns and production losses. The author with his experiences for the last 37 years in furnaces of all sizes tried to attempt to investigate into the reasons for premature failure of lining.

Jan 1, 2007

By Isobel Clark

This paper reviews some of the traditional methods of reserves estimation based on lognormal distribution with or without an additive constant. In the rush to computerize mine planning and grade control generaly, proven estimation methods, such as Sichel's t, seem to have been overlooked. By use of a personal microcomputer, the traditional methods were investigated thoroughly, the results being tested against existing tables and figures. The fitting of a lognormal distribution, including estimation of the additive constant, is discussed, and the calculation of Sichel's t estimator and its associated confidence limits is described in detail. Payability calculations for a lognormal distribution are also covered briefly. The advantages of personal computers, particularly speed and ease of use, are emphasized. This low-cost approach permits detailed investigation of some of the assumptions and approximations inherent in the established methods of calculation. Several disturbing discrepancies are revealed in various factors, and some generalized statements made by previous authors are found to be over-simplistic. Full details are given of acceptable approximations and computer algorithms, and concern is expressed over the possible loss of proven methods under the welter of new, sophisticated computer software.

Jan 1, 1987

By J. Githiria, C. Musingwini

"Cut-off grade is a decision-making criterion often used for determining the quantities of material (ore and waste) to be mined, ore processed, and saleable product. It therefore directly affects the cash flows from a mining operation and the net present value (NPV) of a mining project. A series of different cut-off grades that are applied over the life of mine (LOM) of an operation defines a cut-off grade policy. Due to the complexity of the calculation process, previous work on cut-off grade calculation has mostly focused on deterministic approaches. However, deterministic approaches fail to capture the uncertainty inherent in input parameters such as commodity price and grade-tonnage distribution. This paper presents a stochastic cut-off grade optimization model that extends Lane’s deterministic theory for calculating optimal cut-off grades over the LOM. The model, code-named ‘NPVMining’, uses realistic grade-tonnage realizations and commodity price distribution to account for uncertainty. NPVMining was applied to a gold mine case study and produced an NPV ranging between 7% and 186% higher than NPVs from deterministic approaches, thus demonstrating improved project value from using stochastic optimization approaches. Background on cut-off grade calculation and optimizationCut-off grade is a decision-making criterion that is generally used in mining to distinguish ore from waste material. Consequently, it is used to determine the quantities of material (ore and waste) to be mined, ore processed, and saleable product. A series of different cutoff grades that are applied over the life-ofmine (LOM) of a mining operation defines the cut-off grade policy for that particular operation. The cut-off grade therefore directly affects the cash flows to be produced and the net present value (NPV) of a project at the mine planning or feasibility study stage."

Mar 1, 2019

By P. R. Mothemela

The objective of the investigation is to optimize the truck and shovel operations for pre-stripping at New Vaal Colliery by introducing campaign mining. The aim of campaign mining is to improve the efficiency of the loading, hauling, dumping, and maintenance operations which are critical to the success of truck and shovel operations. The current loading (single-sided loading method), hauling, and dumping operations at New Vaal Colliery were found to be inefficient. Time studies were used as a major indicator to highlight the inefficiency of the truck and shovel operations, and it is recommended that an improved loading configuration, hauling, and dumping operations be implemented by using campaign mining. It is also recommended that a service truck be used to maintain the pre-stripping fleet in order to reduce travelling times to the main workshop. As expected, the improved operating conditions will lead to an increase in pre-stripping production.

Jan 1, 2013

By J. Jacobs

The three-product cyclone was originally developed in Russia and is now extensively used in China. The cyclone has recently entered the South African coal industry, and with the obvious advantages that this item of process equipment offers our ever-evolving industry it is safe to assume that it will add value to dense medium circuits in South Africa. Some of the possible applications include: ? Producing multiple products using a single dense medium circuit. These can typically be a primary product with calorific value of 27.50 MJ/kg and a secondary (middling) product with a calorific value of 22 MJ/kg ? High-density separation with a low circulating medium density. Anglo Thermal Coal and Exxaro have pioneered the use of these units at Umlalazi and New Clydesdale respectively. Extensive test work has been performed at Umlalazi to determine the efficiency of the unit and to determine how it compares with the conventional DSM (Dutch School of Mines) cyclone. Some people in the coal industry were initially sceptical and expected the performance of the three-product cyclone to be inferior to that of the conventional dense medium cyclone. The results of the test work have, however, shown that the efficiency of the unit is comparable to that of the cyclones currently employed. A valid concern expressed is the control over the cut-point density of the second stage separation, and work is on-going to find the optimal way to control the secondary separation density. Theoretically, the secondary separation density can be manipulated by changing the orifices of the unit, especially the spigot of the secondary stage. This remains to be proven, and a series of tests is currently being planned. Whatever the result of these tests may be, the three-product cyclone definitely has a place in the South African coal processing industry as it offers a low OPEX and CAPEX solution for producing multiple products from a single circuit, as well as the ability to operate at very high separation densities, while making use of low-density circulating medium. Keywords dense medium separation, DSM, three-product cyclone, coal processing.

Nov 1, 2013

By A. Hoogervorst

Cyanide is a key contributor to the efficiency of gold extraction. Public perceptions of cyanide are emotive and following some publicised incidents involving cyanide, the gold mining industry established a voluntary cyanide code for the manufacture, transport and use of cyanide in the production of gold. The paper describes the development of the code, its content and the third party auditing of the code as a means of establishing and maintaining benchmark standards. In adhering to the cyanide code requirements, there are overlaps with other management systems such as ISO 14001 and OHASA 18001 and the paper seeks to show how existing mine systems can readily accommodate cyanide code compliance and that operating and auditing the cyanide code can assist in the integration of mine heath, safety and environmental management systems.

Jan 1, 2009

By D. A. J. Ross-Watt

Right now the South African mining industry is a high-profile, vital contributor to the nation just as it has been for the past one hundred and twenty-six years since the discovery of diamonds-perhaps even further back if the mining of copper, iron ore, tin, and other minerals in earlier centuries is included. The media in 1995, as has been the case over the years, bear testimony to the complex interactions between the industry and its stakeholders: shareholders, government, employees and their unions, training and educational institutions, researchers, markets, the public, and suppliers of goods, services, and infrastructure. The pressures and challenges that the industry continues to face can be summarized as safety and health, competitiveness, and social and environmental responsibility. There are no surprises here. The motivation for the industry to perform well in these areas is clear; the focus I intend to bring is on the most important tool required for success-that of good mining engineering. This Address sets out - to review the mining aspects that have been discussed in South Africa during the first five years of the decade, a discussion that shows the return of the country as an important mining forum, confirms the role of professional institutes and associations in the development of mining engineering, and brings current relevant issues into focus - to highlight the vital role of mining engineering in the industry, and to identify priorities for the remainder of the decade - to provide the prospective mining engineer, the mining-engineering student and trainee, and the practising mining engineer and mine manager with a better appreciation of the mining-engineering discipline. institutes and ssociations

Jan 1, 1995

By J. C. van Dyk, F. B. Waanders, J. Brand, C. A. Strydom

"Underground coal gasification (UCG) is a fast-emerging, in situ mining technology that provides access to low-cost energy through the utilization of coal reserves that are currently not technically or economically exploitable by conventional mining methods.Groundwater monitoring for conventional coal mining in South Africa is well established, with SANS, ASTM, and ISO standards for the specific environment, location, and purposes. South Africa’s groundwater is a critical resource that provides environmental benefits and contributes to the well-being of the citizens and economic growth. Groundwater supplies the drinking water needs of large portions of the population, and in some rural areas it represents the only source of water for domestic use. Implementation of, and adherence to, groundwater monitoring standards are thus non-negotiable.The groundwater quality management mission, according to the Department of Water and Sanitation in South Africa, is set in the context of the water resources mission and reads as follows:‘To manage groundwater quality in an integrated and sustainable manner within the context of the NationalWater Resource Strategy and thereby to provide anadequate level of protection to groundwater resources and secure the supply of water of acceptable quality.’ (SABS, 2016).In this paper we propose fit-for-purpose groundwater monitoring standards for a commercial UCG operation. It is important to proactively prevent or minimize potential impacts on groundwater through long-term protection and monitoring plans. Scope of study / standard proposal The purpose of this paper is to set out a National Standard Proposal to emphasize groundwater monitoring as one of the five strategies of the ‘Policy and Strategy for Groundwater Quality Management in South Africa’ (Department of Water Affairs and Forestry, 2000) and to align it with the National Water Act, Act no. 36 of 1998 (Republic of South Africa, 1998).The focus of this standard is directed solely towards groundwater monitoring during underground coal gasification (UCG). Groundwater in this context refers to water as sampled from dedicated monitoring wells around the targeted site, which will include the shallow aquifer referred to as groundwater, and water flow at the level of the underground gasifier, referred to as ‘coal water’."

Oct 1, 2018

By H. D. Mtegha

The Southern African Development Community (SADC) aims to harmonize mineral policies and regulatory regimes in the minerals sector. This paper provides a review of the progress made towards harmonization of mineral regimes in the region. It singles out only the mining fiscal environment, as this is normally one of the key issues of interest to potential investors as well as the host state. Indications are that the region is slowly progressing towards a more harmonized approach, and there is evidence that the ?race to the bottom? has been prevented, which is the basis for an integrated mineral sector that the region aspires to.

Jan 1, 2011

By U. W. O. L Vogler

"The behaviour of rocks depends on their material properties, and therefore it is important that these properties are determined by relevant and reliable laboratory testing methods. The ISRM Suggested Methods are very important documents in this regard, and a draft suggested method exists for the determination of the ’complete stress-strain curve for intact rock in uniaxial compression’. The method specifies the required geometry of specimens and the required testing procedures. The research described in this paper involved the determination of complete stress-strain curves for two materials, one exhibiting the Class I characteristic, and the other the Class II characteristic. To obtain a better understanding of the deformation behaviours in the post-peak region, tests were carried out on specimens of both material types with different length-to-diameter ratios. The results showed that the geometries of the test specimens influence the stressstrain curves in the post-peak region. The implication is, therefore, that the numerical values obtained for the slopes of the post-peak graphs are not material constants, but are geometry-dependent. Explanations for this behaviour are given. These findings have important implications regarding the use of post-peak data, for example for blast fragmentation considerations, and for evaluation of rockbursting potential. The research findings are based on a limited amount of laboratory testing, and should be confirmed by further testing. IntroductionThe most common approach for studying the behaviour of rock is by compression testing of cylindrical specimens in the laboratory. Rocks respond to forces by deforming and eventually breaking. The strength and the deformation characteristics are derived from the stressstrain curves produced. Standard shapes and sizes for the test specimens and standard loading rates are recommended in the Suggested Methods of the International Society for Rock Mechanics (ISRM) and the American Society for Testing and Materials (ASTM) standards. In spite of these standards, there remain certain aspects of testing which require further attention. The research described in this paper deals with deformation and failure behaviour of rock materials using stiff, servocontrolled testing equipment. The particular objective was to test the premise that the behaviour of cylindrical rock specimens in the post-peak region of the stress-strain curves does not reflect only a material characteristic, but is influenced by the height-to-diameter ratio (the geometry) of the rock specimen. An additional objective was to investigate the effect of the stiffness of the test equipment on the outcomes of tests."

Jan 1, 2016

By M. C. J. van der Merwe

"Carboxymethyl cellulose is an organic binder used in the iron ore pelletizing industry. The basic principles of how carboxymethyl cellulose (CMC) solutions behave during the pelletizing process and how these principles affect the drop and compression strengths of the pellets are poorly understood. The aim of the investigation was therefore to gain knowledge on the behaviour of CMC during the pelletizing of haematite concentrate.Haematite pellets with different additions of CMC (0.1–0.4 wt%), were subjected to drop tests, compression tests, and free moisture content analysis. The relationship between the drop strength, compression strength, free moisture content, elapsed time, and CMC concentration was analysed.The drop strength had a strong correlation with the free moisture content of the haematite pellets, with a correlation coefficient of 0.94. The compression strength of the CMC-bonded haematite pellets increased as the free moisture content decreased, reaching a maximum upon depletion of the free moisture content. Haematite pellets with CMC concentrations of 0.1 and 0.2 wt% developed most of their strength within the first day after pelletizing, whereas pellets with concentrations of 0.3 and 0.4 wt% developed most of their strength between one and two days after pelletizing. The time within which CMC-bonded haematite pellets develop most of their strength is therefore dependent on the CMC concentration. IntroductionFines are produced during the beneficiation of iron ore. These fines are separated from the lump ore and can be upgraded to produce a concentrate, which is used as a raw material for the production of pellets. Pellets in turn form a key burden material for direct reduction processes as well as the blast furnace (Zhu et al., 2015).Inorganic binders such as bentonite have been used predominantly in the iron ore pelletizing process to obtain pellets with suitable properties (Eisele and Kawatra, 2003). These binders, however, have the disadvantage of introducing impurities into the pellets. This has resulted in organic binders being pursued as suitable replacements for inorganic binders, of which carboxymethyl cellulose (CMC) shows good potential. Although CMC has been used as an organic binder in iron ore pelletizing, the fundamental principles of how it behaves during pelletizing and how these impact on pellet properties are poorly understood."

Jan 1, 2017

By P. G. Terrazas Prado

This paper presents the results of research on the development and application of a custom-made truck cycle and delay automated data collection system (TCD-ADCS) in a surface coal mining. Truck cycle and delay field data are locally stored in trucks and then synchronized and replicated through a wireless network into a centralized server containing an already-developed integrated production management system (IPMS). The system relies on motion sensing and distance travelled in order to automatically define the cycle starting/ending points, cycle time, position, and delay time. Connectivity and communication between loading equipment and trucks are also established. Communication between the equipment operators and TCD-ADCS system is via a user-friendly graphic interface. The hardware used for the development of this system consists of a rugged touch-screen personal computer, 2.4 GHz radio transmitter antenna, and a commercial GPS receiver. The system was developed, tested, and deployed at a surface coal mine in the USA. Keywords surface coal mining, truck and shovel, data collection, information systems.

Nov 1, 2013

The following contributions were received to the paper entitled 'Safety in South African mines: An analysis of accident statistics', by H.S. Eisner and J.P. Leger, which appeared in the J. S. Afr. Inst. Min. Metal., vol. 88, no. 1, Jan. 1988, pp. 1-7. Contribution by H. WAGNER* The paper by Dr H.S. Eisner and Mr J.P. Leger is critical of the safety situation on South African mines and portrays the industry as having little concern for the health and safety of its workers. Moreover, the casual reader gains the impression of deliberate misinformation by the industry to the public concerning safety maters. Furthermore, certain socio-economic reasons are advanced for the apparent differences between the fatality and injury rates reported for coal mines in South Africa and those for the United Kingdom. Contribution by S.A. WATTS. Authors Eisner and Leger are to be commended on their paper, which highlights, according to their interpretation, various shortcomings of both the Chamber of Mines accident statistics and those published by the Department of Mineral and Energy Affairs. Authors' Reply We gratefully acknowledge Dr Wagner's contribution to the discussion on our paper. For convenience, we shal use his sequence of comments in our reply. Before doing so, however, it may be useful to explain how our paper came to be written. After the explosion at Hlobane Colliery in 1983, one of us (HSE), in February 1984, was retained by the lawyers acting for some of the dependants of the victims to advise on technical maters relating to the explosion. Contribution by Ms S.A. Wats Some of the points made by Ms Wats have already been answered in our comments on Dr Wagner's contribution. We are fully aware that the number of accidents leading to absences of less than 4 days would be much greater than shown in our bar chart, and are grateful to Ms Wats for drawing attention to the specific exceptions that can make a 1-3 day accident compensable and that are clearly responsible for the relatively low count in that category of the chart.

Jan 1, 1988

By A. C. Scott

A detailed fundamental model of a zinc electrowinning cell has been developed and validated for both steady state and dynamic simulations. This model was used to investigate the effects of a range of operating variables and to find their optimum values. As well as providing useful design information for a planned upgrading of the EZ refinery, more generally it demonstrates the potential benefits to the minerals industry of the applications of modern CAD flowsheeting techniques. The SPEEDUP equation oriented CAD package was found most suitable for this task as the user can easily generate models specific to his site with any number of components and mixture properties.

Jan 1, 1987

By M. Kannenberg

When coal properties are estimated geostatistically for mine planning in the hardcoal industry, there is one important supposition which influences the reliability of prediction of economically profitable parts of the deposit. This is the fact that activities in hardcoal exploration and mine planning are characterized by distinct levels of information and knowledge upon which decisions of economic import must be based, for example, whether exploration should proceed or not, or which methods and strategies should be used to maximize search efficiency. To get more reliable results for mine planning, in particular, advanced kriging methods (e.g. conditional simulation) have to be introduced and checked for their reliability in historical analyses (post-mortem studies). By using this feedback, kriging results from underground samples or production data can be compared with results gained by advanced geostatistical methods from exploration boreholes.

Jan 1, 1987

By M. Helm

Over the last 40 years, numerous investigations have focussed on the preg-robbing capacity of carbonaceous material during gold ore processing. Various techniques have been applied to characterize the physical and chemical properties of the carbonaceous material in efforts to predict its preg-robbing capacity. The present study, which forms part of an ongoing investigation, is specifically designed to increase the understanding of preg-robbing in ores containing carbonaceous material. In excess of 100 samples from 13 gold mines located in major gold provinces of the world have been incorporated into the present study. These samples were characterized using industry standard metallurgical techniques and were shown to have gold adsorption capacities ranging from a few grams to many hundreds of grams of gold per ton of ore. Further analysis showed that the crystalline nature of the carbonaceous material, which is related to its geological history, is important in determining the preg-robbing capacity of an ore. This finding builds on the common understanding that the preg-robbing behaviour of an ore is related to the amount (or abundance) of carbonaceous material present in that ore. In this study, Raman spectroscopy was used to evaluate the physical nature of carbonaceous material. This is a tool which has been successfully applied by researchers for the characterisation of carbon materials, with respect to crystallite size and lattice defects. Raman analysis of the samples included in this study showed varying degrees of disorder in the carbonaceous materials from the different deposits. Comparison of the Raman spectra with the gold loading capacities of the samples indicated a direct relationship between the structure of the carbonaceous material and its capacity to preg-rob gold. From this, a simple and robust method has been developed based on the Raman spectra of the sample and carbonaceous material content to predict the preg-robbing capacity of an ore. The potential exists to develop a predictive tool using Raman spectroscopy for characterising the preg-robbing capacity of an ore. Such a tool would have potential application in projects ranging from the early stage of exploration through to more detailed feasibility studies and mining operations. The result of applying the predictive method outlined in this paper would be the effective and proactive management of the deleterious influence of carbonaceous material on gold recovery in mining operations.

Jan 1, 2009

By R. Hoare

TSG Consulting works with many of the major global mining companies using simulation modelling as an integral component in their development team's processes to determine which combination of infrastructure options, operating performance and operating rules best achieve project goals. All systems can be divided into a series of subprocesses. Conventional management and design practices focus on the optimisation of these system components. However, the interaction between subprocesses means that improvements made to the individual components do not necessarily translate into total system performance improvement. TSG Consulting advocates a `total integrated system approach' to understanding the behaviour and performance of complex interacting systems. In a constraint-based integrated set of processes, the instantaneous system capacity is limited by the subsystem component capacity that is the bottleneck at that point in time. Additionally, real world stochastic and dynamic influences tend to have knock-on effects across subsystem boundaries. This necessitates the requirement for simulation modelling to develop and validate solutions that are sufficiently robust to deliver sustainable outcomes. The key to maximising production is to understand the causes and effects the inherent variability has on component performance, subprocess performance and most importantly, the total integrated system performance. The correct use of simulation modelling techniques allows study teams to evaluate the relative merits of different capacity enhancement proposals. Put simply, when done well, simulation modelling provides a quantitative and rational process to enhance the knowledge and insight needed to make informed decisions.

Jan 1, 2007