Search Documents

By L. M. Tavares, T. M. Campos, P. M. Faria, R. M. Carvalho

Recent advances in mechanistic ball mill modelling are expected to allow for more accurate predictions that overcome the well-known limitations of phenomenological approaches, including their inability to predict the effect of liner geometry and their wear, in grinding. Although able to describe continuous operation, the UFRJ model of ball mills has only been validated in the past in mills that operate in batch mode, either in laboratory or pilot scale. The present work demonstrates the application of the mechanistic UFRJ ball mill model to predict fine grinding of iron ore in a pelletising plant in Brazil, the first application of such a mechanistic modelling in continuous mode. It shows that the model provides accurate descriptions of flows after iterations in a closed-circuit with hydrocyclones. Keywords: Ball mill, iron ore, grinding, modelling, particle breakage

Jan 1, 2020

By R. W. Ottermann, N. D. L. Burger, A. J. von Wielligh, P. R. de Wet, J. L. Steyn

Underwind and overwind protection system concepts for mine hoist shafts were developed in conjunction with and for the Safety in Mines Research Advisory Committee (SIMRAC). End-of-wind operation of mine hoists is the most hazardous aspect of mine hoisting, carrying the highest risk of loss of life, injuries to workers and loss of production. Systems operating mechanically and with local actuation were developed. This was done in order to remove the increased risk associated with dependency on remote or external energy and information supply associated with most existing protection systems. The proposed underwind protection system concept absorbs the energy of motion of a conveyance overrunning the design lower limit of travel by drawing a metal strip through a set of rollers. This action causes dynamic cyclic plastic bending of the strip material that converts the kinetic and potential energy of the conveyance into strain energy of the metal. In the concept design a pair of cable slings attached to the strips catch the overrunning conveyance and transfer the retardation force. The proposed overwind protection system concept absorbs the energy of motion of a conveyance overrunning the design upper limit of travel by early detaching of the conveyance from the hoist cable. This detaching is carried out via an additional humble hook activation mechanism fitted at a sufficient height below the spectacle plate to allow the conveyance to retard to standstill under gravity before it would crash into the spectacle plate. The conveyance so brought to rest is prevented from falling by means of jack catches on the conveyance interacting with a rack (toothed profile) fitted on the guide rails in the retardation zone. Scale models (1:10 scale) of both protection systems were designed for conformance with established retardation standards. The retardation standards were limited by the requirement of passenger safety in retarding cages. The models were then built and tested in a 1:10 scale shaft model. Retardation performance close to the required levels was achieved. The retardation distance required should allow such systems to be retrofitted to most existing shafts. Given the simplicity and robustness of the designs

Jan 1, 2003

By I. J. Barker

This paper argues that the scale up of furnaces and the supply of electricity are going to be two major issues that will affect the ferro-alloy industry in the near future, and that economic factors will drive this development. The most common type of furnace for producing ferroalloys at present is the submerged-arc furnace with three electrodes, fed from a three-phase AC electrical supply. The scale up of this technology has now reached a fundamental constraint, which is caused by the electrical reactance of the secondary circuit. If the economy of any further scale up is to be achieved in the future then a different technology will have to be used. The supply of electrical power in future is likely to become amore complex issue than it is at present. Existing submerged-arc furnaces tend to run at fairly steady loads, but the ability to swing the load under demand-side management may offer advantages, and may allow a furnace to obtain cheaper power from the organizations that supply this power. This will have to be counterbalanced against the nuisance factors incurred by having a varying load in the operation of the furnace. Various options are therefore discussed in this paper. The possibility of scale up of Søderberg electrodes is discussed, as well as the use of DC power and multiple electrodes. Some of the issues with load swinging are also examined. A particular scenario is also briefly presented to show that considerable further scale up of ferro-alloy furnaces is still possible.

Jan 1, 2011

By T. G. Pedro, Q. Gonzalo, R. E. Roberto

Anionic surfactants, such as oleic acid and sodium oleate (OLE), and cationic surfactants, such as dodecyl amine-hydrochloride (DDA), are used as flotation collectors of spodumene. However, recovery is poor even if activating ions are used because gangue minerals are also activated. Some reports demonstrate that OLE/DDA mixtures act as a selective collector to enhance spodumene recovery. From mostly macroscopic tests, it has been argued that anionic OLE and cationic DDA form electroneutral complexes, which are adsorbed on the mineral surface through chemisorption; however, no molecular evidence has been presented. Therefore, the adsorption mechanisms of the collector mixtures remain mostly unknown. It seems necessary to first study the behaviour of these surfactants confined in salt solutions, to determine auto-associations when they are pure and cross-associations when mixed, the transition from monomers to micelles, and the structure of the micelles and the effects of pH, temperature and concentration. In this paper, ab initio calculations are first used to determine the surface charge distribution of OLE and DDA separately. Then molecular dynamics simulations are used to determine the conformation, aggregation, and diffusion of these pure and mixed surfactants in freshwater and saltwater with the ionic strength of seawater in a pH range. In particular, it is interesting to determine the various associations that result in mixtures of both surfactants and the impact of alkali and alkaline earth metal cations on the structures formedp. Cations influence the order of the structure and orientation of water dipoles, reducing the mobility of water, ions, and surfactant molecules. This knowledge is critical to improve the molecular understanding of the adsorption mechanisms on minerals. Keywords: Computer simulation, molecular dynamics, flotation, collectors, saltwater

Jan 1, 2020

By R. V. Ramani

Managers need quality information for effective decision making. This demand, at the present time, is being fulfilled by the increased use of computers via information systems, decision support systems and management information systems. The idea of incorporating intelligence into computers to aid decision-makers has been evolving for over two decades. In recent years, significant progress is reported on applications to business and sciences. In engineering functions, the Artificial Intelligence approach that seems to have great potential is the application of Knowledge Based Systems. The primary objective of this paper is to identify domains in mining engineering where application of knowledge based systems could be beneficial. In- corporation of the expertise required during the analysis and interpretation stages of an engineering design problem through knowledge based systems is recognized as an area of significant benefit. To this end, the components of knowledge based systems for mine ventilation and strata control design are described. The potential applications and limitations of knowledge based systems are outlined.

Jan 1, 1987

By M. David

This paper addresses the problem of technological transfer in geostatistics. Expert systems have become popular in certain fields because the needs of the industry are not provided for by traditional concepts and systems of education. The explicit knowledge approach in developing expert systems is presented through two experiments. The first describes a dedicated system written in GOLDEN LISP and the second a shell, using INSIGHT2, which has more general applications. Using expert systems forces on the user a new approach to parameter definition, and as an example an original method for the research of any anisotropy axes is developed which might well be useful in traditional programming. Two examples of application to a coal and a gold deposit are given.

Jan 1, 1987

By C. M. G. Wortley

One of the major deliverables of the AMIRA P754 Project, which was sponsored by several major mining companies, was a code of practice and guidelines for metal accounting for the mining and metallurgical industry. These had the objective of improving the auditability and transparency of metal accounting from mine to product, thus assisting in good corporate governance. The overriding objective of mass measurement for metal accounting is to establish the mass of the particular material or component present at a specific time, or the mass flow of that component over a defined time period, to a defined accuracy suitable for metal balancing. As such, it is the first measurement in the chain that includes sampling, sample preparation and analysis, each of which introduces its own errors. Materials often contain moisture, the proportion of which must also be established in order to obtain the dry mass. They may also have to be measured as a volume or mass/mass flow of slurry, or in stockpiles or storage areas, in which case the relative density must be measured. Both the density and moisture measurement often introduce significant error. Whereas a great deal of effort has been directed at sampling, sample preparation and analysis to improve accuracy and establish the error, the same can seldom be said for the mass determination, including the moisture and density measurements. The possible major causes of error are highlighted and methods of reducing them discussed. Mass measurement can be classified into those measurements necessary for custody transfer and primary accounting of the input and output streams to a plant or operation, and measurements required for secondary accounting, or management control. The latter include intra company transfers and plant area performance, and those required for plant control only. This paper is concerned only with primary accounting measurements. The code and best practice state that the equipment should be certified (as sized) as is required for custody transfer. The most accurate and precise of the various possible methods is the static measurement of mass on a weighbridge, platform scale or a weigh bin. If static measurement is not possible, which is often the case for ore fed to a plant, possible alternatives are electromechanical conveyor belt weighers or in-motion weighing of rail trucks. In all cases the material must be adequately sampled to enable a representative moisture content to be determined to calculate the dry mass. Where material is flowing inside conduits, only certain types of the multiplicity of flow meters available may be used and, in the case of slurries, very few flow meters are suitable. As most flow meters measure volume or velocity, the density of the material must also be measured. The basic requirements in order to achieve satisfactory results for the mass, of the component of interest, are listed, as well as common problems and pitfalls encountered in practice. The measurement of the mass of stockpiles and in-plant stocks, often required for metal accounting, is often the largest source of error in metal balances. The reasons for this and methods for reducing and managing the effect are discussed.

Jan 1, 2009

By R. Gurung, S. Asokan, Ch. V. G. K. Murty, R. Upadhyay

Tata Steel Limited which is Asia?s first and India?s largest integrated private sector steel company, as part of its vision to grow in related industries is also undertaking the Titania project. The project will involve mining, separation of ilmenite and other valuable minerals from the inland heavy mineral sands deposit in the Indian state of Tamil Nadu. The raw material will be beneficiated to synthetic rutile, titanium dioxide pigment and ultimately to titanium metal. The recently concluded feasibility study revealed that the deposit under consideration has 10.4%of total heavy mineral content and 15.2% slimes of the size below 63 µm, over an average sand thickness of 6.9 metres. The presence of about 15% slimes in ROM sand coupled with scarcity of water at the project site complicates the slimes handling/disposal system, requiring the development of an innovative, efficient and effective system for disposal of slimes. Mineral characteristics of slimes revealed the presence of kaolinite clay, which poses its own challenges in thickening/dewatering of slimes. This paper outlines the detailed studies conducted, including slime characterization, settling and thickening characteristics, and ge-technical studies to arrive at an efficient and effective slime handling/disposal system, with a view to plant saplings on the mined-out reclaimed land with species typically suitable to that environment.

Jan 1, 2007

A set of six design principles for rock engineering was developed by Bieniawski: design objectives; minimum uncertainty; simplicity of design components; state-of-the-art practice; optimization; and constructability. These principles translate into a ten-step design process. Although this methodology was developed for rock engineering, it is applicable to any design process, feasibility study, etc. Diligent use of such a process will ensure that a defensible design or evaluation has been carried out. Recently a ?strategic conversation? process has been identified by Ilbury and Sunter that includes the following ten steps: scope; players; rules of the game; key uncertainties; scenarios; SWOT analysis; options; decisions; measurable outcomes; and meaning of winning. A comparison of these steps with those of the design process shows a remarkable correlation. This is perhaps not surprising since engineering design is a strategic up-front issue, and front end loading in a project is critical to achieve the expected project performance. Based on the close correlation between the strategic conversation and engineering design processes, a circular design process, rather than a linear process, is proposed. The ?circle of design? better reflects the importance of review and monitoring in the two phases of successful design and implementation?defining the design, and executing the design.

Jan 1, 2009

By M. Rudman, L. Pullum, L. J. W. Graham

Centrifugal pumps are the workhorse of hydraulic conveying systems but their performance is derated when viscous non-Newtonian fluids, such as pastes and/or coarse solids are present. The reduced performance for purely viscous Newtonian fluids may be calculated using techniques such as the Hydraulic Institute method, but similar deration for non-Newtonian fluids is not so easy to apply. As part of the AMIRA P599 project investigating high concentration suspension pumping, centrifugal pump tests were systematically conducted on a wide range of non-Newtonian coarse particle suspensions. Suspension sup to 38% v/v of coarse particles with mean diameters in the range of 1.1 < d50< 3.4 mm suspended in carrier fluids with dynamic yield stresses of 0 < t?< 17.2 Pa and shear thinning indices in the range 0.35 < n< 0.79 were examined. Techniques such as the Hydraulic Institute de-ration method require a characteristic shear rate to be assigned before application with a non-Newtonian fluid, and a method based on pump geometry, fluid rheology and flow rate is proposed. This method predicts the dramatic characteristic reduction in head at low flow rates that is often observed and explains why larger pumps are relatively insensitive to this form of head deration. Head deration due to the presence of coarse particles in non-Newtonian carrier fluids is seen to follow similar trends to that of Newtonian suspensions and often dominates the total deration procedure.

Jan 1, 2007

By M. Rudolph, J. Sygusch

Froth flotation is well-established and efficient in the selective separation of valuable particles from unwanted material with sizes ranging from 10 μm to 200 μm. However, when it comes to the separation of ultrafine particles (< 10 μm) there are still some challenges, or rather opportunities. This research aims at developing a method for the separation of ultrafine particles based on multiple particle properties. Amongst such properties are wettability, morphology (shape or roughness) and size with applications not only in mineral processing but in general chemical engineering. In this study, three differently shaped fractions are used as valuables for testing: spherical particles, elongated particles and irregularly shaped particle fragments; together with ultrafine magnetite as the gangue material, in order to investigate the effect of particle morphology on ultrafine particle flotation, as well as wettability, which is varied by esterification using alcohols. Flotation tests are carried out using a novel flotation device that was designed especially for the flotation of ultrafine particles, combining advantages from machine-type froth flotation and column flotation. The results showed that, in contrast to previous studies, recoveries for ultrafine spheres were higher than for ultrafine fragments for all wettability conditions, and hydrophobisation generally increased particle recoveries for said morphologies. Tests using fibres showed different behaviour as hydrophobisation had negative effects on their recovery, despite increased selectivities and kinetics. These findings suggest that apart from influences of particle properties within the suspension zone, their effects on the froth characteristics should be studied in more depth. Keywords: Ultrafine particles, Flotation, Particle shape, Wettability, Esterification of glass, Hydrophobisation

Jan 1, 2020

By E. Molobi

"Studs are rods threaded on both ends and are used as mechanical fasteners for two or more components. Stud finds usage in industries such as automotive, construction and aviation. The advantage of studs is that they allow for disassembly of components during maintenance. Studs are continuously subjected to both tensile and shear stresses, depending on the application, therefore they should be manufactured from suitable materials that are capable of withstanding all these external forces. Studs are sometimes manufactured from re-sulphurized steel due to its improved machinability; however, there is a certain limit on the amount of sulphur, above which failure may occur. Premature failure of studs has been a common problem, but failed studs are commonly replaced with new ones without conducting failure investigations. The present work investigates the premature failure of two re-sulphurized steel studs used on a rocker arm assembly and recommends alternative materials. The investigation was carried out by conducting visual examination, microstructural analysis, hardness measurements, chemical analysis and a detailed scanning electron microscopy (SEM) investigation on the fracture surface.IntroductionTwo rocker arm studs used on a 16-cylinder diesel locomotive engine failed prematurely after being in service for less than 5 months. The rocker arm studs had a life-cycle of 5 years. The studs were manufactured from resulphurized steel. The paper aims to establish whether re-sulphurized steel is applicable for the manufacture of studs in the automotive industry.BackgroundLocomotives are classified as either electric or fuel-powered. Diesel locomotives are an example of fuel-powered locomotives. This type of locomotive uses a diesel engine as a means for propulsion. An engine converts chemical energy into mechanical energy required for traction. In an internal combustion engine a rocker arm is an oscillating lever that conveys radial movement from the cam lobe into linear movement to open and close poppet valves of cylinders (Husain and Sheikh, 2013). The rocker arms are secured on to the cylinder head by rocker arm studs."

Jan 1, 2016

By L. Dison

There are many potential uses in gold mining for an initially stiff element of backfill that will yield at a predetermined load and maintain that load to beyond a compression of 30%. Such elements could be used as yielding rib pillars, as replacements for more conventional supporting packs, as con- fining bulkheads for mass backfill, as supports to provide lateral constraint, and load-carrying augmentation to overloaded rock pillars. The paper describes a system of reinforced cemented backfill that can be used to provide the above requirements. The necessary characteristics of the reinforcing and the cemented tailings are described together with the method of design to obtain a predetermined stiffness and yield load. The load-compression characteristics of the reinforced tailings elements are described and the effect of changing various of the design parameters is demonstrated.

Jan 1, 1988

By D. A. Vetter

A novel mathematical model is presented which describes the behaviour of beds of particles, of uniform size and shape but different densities, during autogenous separations. The approach used in the formulation of the dispersion model is a phenomenological one based on a statistical view, which leads to a diffusion-like representation of the autogenous-separation process. Although the model currently considers only density-related phenomena, it accounts quantitatively not only for the density-segregation aspects of the process but for the interactions between the particles. Quantitative predictions of the dispersion model are compared with the results obtained in tests using a specially constructed experimental batch jig, and it is shown that the model provides an adequate quantitative description of the process for particles of uniform size and shape. It is pointed out that, for the description of more complicated autogenous separations, a more rigorous formulation of the particle drag and density-segregation terms will have to be incorporated into the dispersion model. Nonetheless it is concluded that the model as presented in this paper provides not only a novel insight into the mechanisms of autogenous separations but a means by which to analyse similar systems.

Jan 1, 1987

By J H. Sullivan

Contents Background information Locality of Kumba?s Iron Ore Mines Sishen?s Product Specifications Geological Description of boreholes Sample Preperation Block delineations Production Geology Process Laboratory information Turnover times reached Inter Laboratory Comparisons Quality control activities in lab Purpose of laboratory Results attained Standard samples Monitoring of processes with QA/QC standards Mean paired difference of duplicates Duplicate samples Conclusion

Jan 1, 2005

By J. P. Beukes

The production of ferrochrome alloy from chromium bearing chromite ores is conducted at high temperature under highly reducing conditions. However, albeit completely unintended, it is impossible to completely exclude oxygen from all high temperature process steps, with the corresponding possibility arising for the generation of small amounts of Cr(VI) species. Certain Cr(VI) species are regarded as a carcinogenic, with specifically airborne exposure to these Cr(VI) species being associated with cancer of the respiratory system. With approximately three-quarters of the world?s viable chromite ore reserves located in South Africa, and annual ferrochrome production approaching almost half of total annual global output, aspects of Cr(VI) generation and control are of particular relevance and importance to the local industry, and naturally to the global industry at large. This paper seeks to examine theoretical and practical aspects associated with Cr(VI)generation (based largely on experience within the local South African industry, but considered to be generally encountered in the broader global industry context), together with mitigating measures that can be applied within the context of the production processes. From the discussions it is clear that significant improvements in various Cr(VI)-related aspects have been made by the South African ferrochrome industry. However, it is also evident that several areas of uncertainty still exist, which require further research in order to better quantify risks and enhance the efficacy of mitigating steps. Keywords Hexavalent chromium, Cr(VI), ferrochrome production, South Africa.

Jan 1, 2010

By B. Geelhoed

A generalization of Gy?s 1979 model for the variance of the fundamental sampling error has been proposed at WCSB2?2005 by Geelhoed. This generalized model can potentially lead to a better correspondence with actual sampling processes. However, a new parameter is required by the new model: ?the parameter for the dependent selection of particles?(Cij). It is important that this new parameter, which is at the basis of the new theory, is well understood in the sampling and blending community. In order to clarify the meaning of Cijand to prevent potential misinterpretation of Cij, we discuss the difference between Cij and an intuitively associated, but different, parameter: ?the parameter for the dependent selection of particle types?(Mij). In this contribution, the theoretical difference between both parameters is clarified. Simulations demonstrate that, numerically, the difference between Cij and Mij can be large. Some additional advantages of the approach which uses Cij are discussed: (i) the approach based on Cijis more general; (ii) in all cases where Mij is known, Cij can be determined as well, while the reverse is not true; (iii) an equation already exists that relates the sample variance to the value of Cij.

Jan 1, 2009

Nowadays, fully encapsulated rockbolts have become a key element in the design of ground control systems. The main reason is that they offer high axial resistance to bed separation. In this research, the load transfer capacity of a fully grouted bolt is evaluated analytically in an elastoplastic rock mass condition. The research considered the effect of bolt end-plate on load transfer capacity. Bolt and surrounding materials were assumed to be elastic and elastoplastic materials respectively. The load transfer mechanism of a fully grouted bolt is a function of parameters such as bolt length, shear stiffness of interfaces, in situ stress, presence of face-plate and distance along the bolt. These factors were analytically evaluated. Finally, the load along the bolt was predicted in different surrounding rock mass characteristics.

Jan 1, 2011

By K. Eckert, A. E. Sommer, S. Heitkam

One highly relevant challenge in flotation is the recovery of fine particles. Due to their low inertia, these particles are mostly pushed aside by rising bubbles. Consequently, they typically exhibit low probability for bubble-particle collision and thus, a poor recovery rate. In this work, the trajectories of fine particles in the vicinity of rising bubbles were investigated. The measurements considered a chain of millimetric bubbles in a rectangular container filled with deionized water. The flow field near the bubbles was measured by tomographic particle image velocimetry (TPIV), employing fluorescent tracer particles of 33μm diameter. Subsequently, trajectories of larger particles and bubble-particle collision events are recorded with 4D particle tracking velocimetry using a high temporal and spatial resolution. The results reproduce the well-known collision of particles on the leading edge of a rising bubble. Additionally, collisions on the tailing edge were observed in cases with a low Stokes number. The TPIV results demonstrate, that the high turbulent kinetic energy in the bubble wake allows particles to divert from the fluid streamlines and collide with the tailing edge of the bubble. The tailing edge collision probability increases with the bubble Reynolds number and decreased particle inertia. Overall, the investigation shows that the collision of fine particles in the bubble wake should be considered for the development of further collision probability models. Furthermore, the importance of turbulence on the fine particle flotation was demonstrated. Keywords: 4D Particle tracking velocimetry (PTV), tomographic particle image velocimetry (TPIV), fine particle flotation, collision probability, bubble-particle interaction, wake induced collision

Jan 1, 2020

Newmont is one of the few remaining large mining companies that was established in the early nineteen hundreds. The company has a long, colourful and enviable history. This paper provides highlights of Newmont?s business and technical history since its inception in 1916, its transition to a ?gold only? company in the early 1990s and progress since that time up until the present day. Details of Newmonts current gold operations and its gold production profile for 2008 are also provided in the paper Over the last 50 years Newmont has developed a host of innovative gold technologies to meet the challenges of treating the complex refractory gold ores, found at the company owned mines in the Carlin region and around the world. Details of the technologies are provided and they include chlorination, roasting, bacterial and pressure leaching, leaching gold with thiosulphate and thiocyanate, N2Tech flotation, HPGR treatment of hard and abrasive ores and, finally, the use of Hydro-Jex technology for improving gold recovery from heaps.

Jan 1, 2009