Search Documents

By J. C. Edwards

The Bureau of Mines developed a mathematical model for analysis of the impact of scrubber bed length, porosity, and gas flow rate on the absorption of C02 in a breathing apparatus. The model accounts for the decrease in available absorbent through chemical conversion. The pre-dicted efflux of C02 from a canister containing LiOR compared favorably with measured values reported elsewhere. It was determined from a com-putational study that the time for breakthrough of C02 at a prescribed level is nearly directly proportional to bed length and inversely pro-portional to gas flow and porosity.

Jan 1, 1987

By J. A. Kost

A survey of 80 coal producers was conducted to determine the extent and scope of respirable dust control research for underground coal mines and the current methods employed to control respirable dust. Results of the survey showed that proper face ventilation and an adequate water spray system are sufficient to comply with mandatory standards in room and pillar mining. Difficulties still exist with longwall equipment, auger miners and buring machines. In these cases, known dust control techniques are not sufficient to obtain compliance. Present state-of-the-art face ventilation and water systems were discussed in addition to the sampling program.

Jan 1, 1980

By T. E. Gray

This report describes the preparation characteristics of the significant coalbeds in Harrison County, W. Va. It is one in a series of Federal Bureau of Mines reports planned to determine coals suitable for the production of metallurgical coke, either as mined or after beneficiation. Over 6.5 million tons of coal was produced in Harrison County, W. Va., in 1958, of which over 3.7 million tons was cleaned mechanically in seven preparation plants. All of the coal cleaned was from the Pittsburgh bed. It has been estimated that more than 1,816 million tons of coal remains in the county in beds 12 inches or more thick. The Pittsburgh and Redstone beds were selected by the Bureau for a study based on current production rates and estimated minable reserves. Sample locations were selected following a study of the literature, conferences with mining engineers and mining company officials in the field, and examination of the available sites. Six samples were collected from the Pittsburgh bed, and three samples came from the Redstone bed, Float-and-sink tests of the samples collected from the Pittsburgh and Redstone beds showed that neither coal could be upgraded to a metallurgical fuel under the standards set up for this study, even after intensive preparation. Finer crushing of the samples moderately increased the yields and slightly reduced both the ash and the sulfur contents in the 1.30-specific-gravity float fractions. Finer crushing slightly decreased the yields in the 1.58-specific-gravity float fractions, whereas it reduced the sulfur content 0.11 percent for the Redstone sample and 0.46 for the Pittsburgh sample.

Jan 1, 1961

By Thys B. Johnson

Operations Research techniques for determining optimal shipping schedules and production and product allocation are discussed. A hypothetical mining operation model is formulated by the Bureau of Mines, and optimal production and product allocation are determined. The technique of sensitivity analysis is discussed and is used to illustrate the effect of the variability in a mining operation on the optimal production and product market plan.

Jan 1, 1969

By D. G. Kuehn

Studies were conducted by the Bureau of Mines to determine the positive ions and neutral species produced in glow discharges of gas streams containing 1.0 percent NO in helium, 29 percent dry air in helium, and 1.06 percent NO in N2, Mass spectrographic measurements were conducted for gas pressures from 2.3 to 10.0 torr and dc currents from 10 to 20 mAo Ion species observed included NO+, N2 +, O2 +, N+, and 0+ with lesser amounts of He+, He2+, and N02+. Variations in various ionic and neutral species with discharge duration were interpreted to be consistent with an electrically induced dissociation of NO to produce N2 and O2. No nitrogen oxides were observed to form in glow discharges of the helium-air mixture.

Jan 1, 1975

By W. L. Cooley

The report provides a detailed analysis of 23 electrical accident countermeasures contemplated for use in the metal/non-metal mining industry. The costs and potential benefits of implementing groups of these countermeasures are estimated, and methods arc outlined by which the operator ran choose countermeasures in an effective manner. The analysis is based largely on an extensive electrical accident event tree which is developed in detail. For those countermeasures which are not currently technically feasible, several prototype devices were developed to help speed development. These included a trolley arc eliminator and a safer mine electricians multimeter.

Jan 1, 1982

By Henry R. Ensminger

Brazil's gross domestic product (GDP) grew only slightly in 1988 to $277 billion at current prices.2 The growth rate was the smallest registered since 1983, when the rate was minus 2.8%. The economy's performance was strongly influenced by a 2% to 3% decrease in industrial production and civil construction. The mineral industry, however, countered the downward trend in the industrial sector and grew a modest 1.4%. In November, Brazil adopted a new Constitution that placed significant restrictions on foreign investment in the mineral industries. Under certain provisions of the new Constitution, foreign companies were prohibited from establishing new mining ventures in Brazil as sole or majority owners. They could now enter the mineral industry only as minority shareholders with Brazilian partners. Foreign companies already established in Brazil had a 4-year grace period to find majority Brazilian partners, or to establish vertically integrated processing operations (mining, processing, smelting, and refining). The new Constitution also prohibited foreign risk contracts for petroleum exploration.

Jan 1, 1990

By S. J. Aresco

The Bureau of Mines has been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heating value of the coal, expressed in British thermal units, and the composition as shown by proximate analyses. To these, when required, are added the ash-softening temperature, the free-swelling index, and the Hardgrove grindability index. Under most of these specification contracts the bidders guarantee the quality of the coal, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instructions4/ issued by the Bureau of Mines, the samples are analyzed in the Bureau laboratory to determine whether the coal is of the quality guaranteed by the contractor and, if it is not, a price adjustment is made. Analyses of the delivered coal and tipple samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) provide valuable data for use in evaluating future bids. In addition, the continuous sampling of coal as delivered is a check on the practical results obtained in burning the coal.

Jan 1, 1957

By J. P. Powell

The importance of recovering more oil from known petroleum reserves has placed increasing emphasis on the application of secondary producing methods. One of the most successful of these has been the injection of water into depleted oil reservoirs. Water flooding is now recognized as a valuable conservation measure that not only prevents the premature abandonment of stripper leases but also is credited with reviving operations in many oil-producing areas previously abandoned. The injection of water into an oil-producing zone as a method of stimulating oil production was legalized in Kansas in 1935. Although water flooding had been attempted previously in other parts of the State, 1935 marked its introduction into the shallow stripper area of eastern Kansas. Two years later flooding was begun in the five-county area that is described in this report. Figure 1 is a map showing the water-flood areas in Allen, Bourbon, Crawford, Labette, and Neosho Counties, Kans. To July 1, 1955, the 77 projects in the oil fields of these 5 counties are credited with recovering an estimated 12.3 million barrels of oil that would not have been produced by methods used previously. These projects are expected ultimately to cover 10,700 acres, of which only 5,400 has been flooded to date.

Jan 1, 1957

By R. E. Hershey

1. Reserves were estimated for three coal beds: Lantana, Sewanee, and Richland. 2. Known measured and indicated reserves for all beds, based on a minimum thickness of 14 inches and on 1,800 tons per acre-foot of coal in place, are estimated at 34 million short tons as of Januray 1, 1954. Of this total, 15 million short tons represents coal 28 inches and more thick. Areas in the beds were omitted from the estimate because available data relative to the bed characteristics were insufficient to permit making an estimate conforming with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves determined by this investigation.

Jan 1, 1956

By L. A. Conley

This report, covering the period January through December 1976, contains abstracts of articles related to cost engineering and economics for chemical and petroleum plants, mining, and other mineral industries from the following periodicals: 1. Air Pollution Control Association Journal 2. Chemical Engineering 3. Chemical Engineering Journal 4. Chemtech 5. Coal Age 6. Coal Mining and Processing 7. Combustion 8. Drilling-DCW 9. Electrical World 10. Engineering and Mining Journal

Jan 1, 1977

By R. T. MacMillan

Many bench-scale tests and studies have been conducted in developing and testing a chloride-volatilization procedure Ear treating low-grade manganese ore from the Maple Mountain-Hovey Mountain deposit of Aroostook County, Maine. The ore, averaging 10 to 12 percent Mn, contains manganese in several forms and is resistant to concentration or extraction by usual physical and chemical procedures. Over 90 percent of the manganese, content of the ore has been recovered using a chloridizing roast in which the ore was heated at 950°-9b0' C. in a circulating stream of hydrochloric acid gas. Chlorides of manganese and iron were volatilized and swept to a fume collector, where they were condensed and separated from the [as] stream. Operation of a small, 1-pound-per-hour shaft Furnace produced enough chlorides for studying other factors in an integrated process such as: (1) Conversion of the chlorides to oxides; (2) recovery of HC1 gas of suitable concentration Ear recycling to the chloridizer; and (3) control of the Mn-Fe ratio in the oxide product to produce a suitable feed for ferromanganese production.

Jan 1, 1956

By T. S. Chen

A study was made by the Bureau of Mines of the temperature and thermal stress distributions in thin circular disks subjected to peripheral thermal shock at various rates of heat transfer. The theoretical analysis is based on one-dimensional radial heat flow by conduction in the disk, and on heat exchange by convection between the disk and its surroundings. Preliminary experimental data obtained from shock tests on thin circular disks of basalt, quartzite, and taconite show reasonably good agreement with theory. The case of constant properties and plane stress is treated. Solutions of the stress distribution are presented for both cooling and heating shocks. The elastic energy stored at fracture is examined, and on this basis an average stress theory is formulated. Physical properties vital to the studies include thermal conductivity, thermal diffusivity, tensile strength, Young's modulus, and linear coefficient of thermal expansion. This work is of importance in predicting the thermal shock responses of a rock body of finite size.

Jan 1, 1966

By J. H. Welsh

This Bureau of Mines report presents guidelines to be considered in the design, installation, and operation of environmental mine monitoring systems in underground coal mines so as to enhance safety in the U.S. mining industry. A review of the current status of mine monitoring in the United States is also provided.

Jan 1, 1987

By J. M. Stuve

Low temperature and high-temperature calorimetric measurements were made by the Federal Bureau of Mines on high-purity samples of Re02(s) and Re03(s) to determine heat capacities and enthalpies. The temperature range of heat capacity measurements was 5 to 310 K for Re02 and 8 to 309 K for Re03. High-temperature enthalpy measurements alone were determined for pure Re207(s,1). The derived standard entropies are S°298 = 11.43±0.01 cal/deg mole for Re02(s) and S298 = 16.55±0.02 cal/deg mole for Re03(s). High-temperature enthalpy equations expressed in calories per mole are as follows: Re02 (s) , H-H298.15 = 16.002T + 1.600 X 10-3T2 + 3.522 X 105T-1 - 6,095 (298 to 1,400 K); Re03 (s) , H-H298.15 = 20.293T + 3.238 X 10-3T2 + 3.950 X 105 T-1 - 7,664 (298 to 1,000 K); Re207 (s) , H-H298.15 = 38.437T + 10.309 X 10-3T2 + 4.315 X 105 T-1 - 13,824 (298 to 413 K); Re207 (s) , H-H298.15 = 30.181 + 17.713 X 10-3T2 - 10,612 (413 to 600 K) ; Re207 (1) , H-H298.19 = 66.101T - 10,092 (600 to 700 K). Gibbs energy of formation (?Gf°) data and related functions over the temperature ranges investigated are tabulated for the three oxides.

Jan 1, 1976

By E. C. Foster

The project objective of this contract is to design, develop, and demonstrate a dust collecting system for auger head miners, used in coal seams 40 inches or less in height, which will reduce respirable dust below the limits established by the Federal Coal Mine Health and Safety Act of 1969. This system was to be incorporated into 3 Wilcox Mark 20 continuous miner. In order to accomplish this, the objective was divided in three main areas. First: To develop a dust control system which would remove by isolation, respirable dust from the face area and areas where miners work. Second: To develop a dust scrubbing system to remove and collect float dust before the air reaches the return airway. Third: To reduce the overall noise levels to which the miners are exposed.

Jan 1, 1974

By J. S. Coffman

Wyoming is estimated to have more than 700 million tons and Utah more than 2.5 billion tons of +10 percent P2O6 phosphate rock considered to have some future economic potential. In Wyoming, the +24 and +18 percent P205 rock potential resources total nearly 250 and 450 million tons, respectively. In Utah, the +31, +24, and +18 percent rock total approximately 33 million, 222 million, and 2.2 billion tons, respectively. These resources are all located above the local drainage levels and do not include latent resources. All of the mining and beneficiation of phosphate rock in the two States is done by San Francisco Chemical Co. The facilities include open pit mines at Vernal, Utah, and Leefe, Wyo.; an underground mine in the Crawford Mountains, Utah, and beneficiation plants at Leefe and Vernal. One of the principal markets for the phosphate rock is Western Phosphates, Inc., fertilizer plant at Garfield, Utah. Recent exploration and development has been under-taken by different companies in the Southeastern Wind River Range, Sublette Range, and Crawford Mountains. The facilities at Leefe and Vernal are in the process of expansion. Some of the areas of western Wyoming contain vast quantities of phosphate rock in minable units, but, because of their remote location, are classed as latent areas. In these areas, there are estimated to be about 700 million, 2 billion, and 3 billion tons of phosphate rock in the +24, +18, and +10 percent P205 grade classes, respectively. The Snake River Range of Idaho and Wyoming is also estimated to contain roughly 21, 106, 177, and 214 million tons of potential resources in the +31, +24, +18, and +10 grade categories, respectively. This area also contains a large amount of latent rock in the more remote areas.

Jan 1, 1967

By E. C. Lane

[The motor gasoline that s being marketed in the United States this summer slightly more volatile then that sold a year ago. This increase in volatility is shown by a general lowering ref the average distillation rang, of about 2°F. During the post 10 years the Bureau of Mines has made semiannual surveys of the gasoline marketed in the United States, the survey just completed being the twentieth in the series. The 12 cities in which samples were collected have beer chosen as representative of the more important marketing territories, as it is obviously impracticable to obtain a sample of every gasoline sold in the entire country.]

Jan 1, 1929

By M. E. Tyrrell

This Bureau of Mines investigation was made to determine the possibilities of using Florida beach-sand concentrator wastes in ceramic products. Sands used in the investigation originated in the Trail Ridge area of Florida, where continued operation of processing plants for recovering titanium minerals promises a dependable source of raw materials. Three general classes of ceramic products were studied, namely: (1) Structural, (2) refractory, and (3) electric-furnace slags.

Jan 1, 1956

By D. A. Elkins

This report is the second of a series of three that will evaluate, in order, the metallothermic, carbothermic, and electrolytic methods of magnesium production. The historical development of the carbothermic process is outlined. Production costs varying from 38.9 to 21.8 cents per pound of magnesium are estimated for different versions of the process. Additional suggested process modifications are listed. The technical and economic potential of the different versions are compared. Areas deemed most promising for future research on the process are delineated.

Jan 1, 1967