Search Documents

By Lloyd A. Morley

The performance of electrical grounding systems in open-pit metal mines is evaluated, using techniques which are described thoroughly. The normal electrical distribution and grounding practices used in metallic open-pit mines are reviewed and compared with coal mine usage. The results are used to generate the included recommendations for Federal Regulations concerning open-pit metal mine grounding systems.

Jan 1, 1976

By N. S. Dalal, B. Jafari, F. H. Y. Green, V. Vallyathan

"INTRODUCTIONThe mechanistic details of the biological events leading to coal workers pneumoconiosis (CWP) are not yet fully understood, despite several decades of extensive epidemiologic1.2 and laboratory studies.2-6 Epidemiologic studies1.2 have shown, for example, that the incidence and severity of CWP differ markedly in the different regions and mines at comparable exposures, but laboratory investigations2-6 have demonstrated only partial correlation of the epidemiologic data with the differences in the mineral composition and the rank of coal mined. In particular, while epidemiologic data indicate1.2 direct correlation of the· prevalence and severity of CWP with the rank (i.e., % carbon content) of coal, this correlation has not been established by laboratory4'6 and animal exposure3 studies. In order to explain these results, in 1980 Artemov and Reznik' suggested that perhaps they arise from the fundamental differences in the surface properties of the coal. dusts inhaled by the coal miners and those used in the laboratory studies: while the miners inhale freshly fractured coal particles, henceforth called the 'fresh' coal dust, the laboratory studies generally utilize 'aged' coal dusts (i.e., dusts that have been stored for many days or even longer). Reznik and Artemov' used electron spin resonance (ESR) spectroscopy to show that the mechanical crushing of some Soviet Union coals generated organic free radicals and that the concentration and the decay times (hence the reactivity) of these radicals were higher for the coals of higher ranks. Since some of the radicals decayed within a few minutes in air, the authors surmised that while these radical species could lead to certain specific pathogenic reactions at the sites of mining operations, this might not be the case in the laboratory studies, due to the conventional use of 'stored' dusts which would be expected to contain significantly smaller free radical concentrations. This is consistent with the recent findings that, standardized, aged coal dusts exhibit minimal cytotoxicity. 8While the above mentioned work of Artemov and Reznik7 did suggest a possible new clue to the pathogenesis of CWP (i.e., the role of the coal based free radical species), no direct biological/cytotoxicity data were provided to show that 'fresh' coal dusts were, indeed, more pathogenic than the 'stale' ones. Because of the rather significant implications of the Artcmov-Reznik hypothesis to the understanding of 1hc biochemical mechanism and, hence, the strategies for the eventual containment of CWP, we have initiated a comparative study of the free radical formation and cytotoxicity properties of freshly crushed coal ·particles. As done by Artemov and Reznik, 7 we have used the ESR technique as the direct method of measuring the concentration and decay kinetics of the coal based free radicals. Our preliminary ESR studies on two Pennsylvania coals, a bituminous (carbon content 72 % ) and an anthracite (95 % carbon) coal, have confirmed the Artemov-Reznik finding that the crushing-induced free radical sites are higher on the coals with higher carbon content (i.e., higher rank).9-11 In the present work we describe our more recent results of a parallel study of the time dependence of the decrease in the free radical content of a freshly made anthracite dust (as measured via ESR) and that of the dust's cytotoxicity potential as measured by the extent of hemolysis of (sheep) erythrocytes. We have also investigated the effects of free radical scavengers on the cytotoxicity potential of the dust and deduce that indeed the free radicals could play a significant role in the initial events in the mechanism of the cytotoxic effects due to the inhalation of coal dust inhalation."

Jan 1, 1990

By R. S. Dean

"INTRODUCTION The idea of direct steel is by no means new. Although the work of Bessemer and Siemens provided simple and effective moans for converting pig iron into steel and established the ""blast-furnace route"" as the almost universal method of producing steel, metallurgists have not ceased to dream of direct steel. By direct steel is meant any process by which iron oxide in ore is reduced to Iron of the same or greater purity than the final steel or wrought iron. That is, carbon or alloying elements would be added as needed, not reduced in unwanted quantities into the iron and then removed more or completely by refining (Bessemer or open hearth) only to be readded in desired quantities.In general, direct-steel processes are ""sponge-iron"" processes, because reducing iron oxide without simultaneously alloying the iron with carbon, phcophorus, sulfur, and silicon present in ore and fuel succeeds only if the temperature is below the melting point of the iron. Such solid iron formed by reduction of iron oxide at relatively low temperature is sponge iron, which is butlery and porous. When the reduction proceeds at the higher temperature at which the particles of metal can weld together or finally even melt to yield pellets or balls that do not have the porosity and low-density characteristic of sponge iron, the product might preferably be called simply ""direct iron."""

Jan 1, 1945

Construction workers may be exposed to hazardous dust containing silica when working in enclosed cabs during construction activities. The National Institute for Occupational Safety and Health (NIOSH) found that equipment operator exposure could be reduced by retrofitting air pressurization and filtration systems on existing cabs, using sweeping compounds on soiled floors, and implementing a dust control program.

Jan 1, 2009

By Avery H. Reed

ALABAMA'S mineral industry continued to expand. This was a record year for many commodities, with expansion in almost all industries. New records were established for the production of native asphalt, fixe clay, miscellaneous clay, kaolin, bentonite, lime, scrap mica, salt, sand and gravel, crushed limestone, crushed marble, and tale. Among the States, Alabama ranked second in the production of bauxite, third in the production of scrap mica and native asphalt, and fifth in iron ore. The mineral industry of Alabama was dominated by the mining and processing of coal and stone, the manufacture of cement, and the production of crude petroleum, which together comprised 87 percent of the total value of production, compared with 86 percent in 1963. The iron ore industry continued to decline. This was the first year in which consumption of imported iron ore exceeded the consumption of domestic iron ore. The coal industry recovered from the slump caused by the abandonment of red iron ore mining by United States Steel Corp., and production expanded 17 percent, for the best year in coal mining since 1948. During the year, the one-billionth ton of coal was mined within the State.

Jan 1, 1965

By W. J. Crawford, P. M. Gruzensky

"Several experiments have been carried out in efforts to evaluate qualitatively a variety of electrolytes for refining bismuth. Most extensive work was done with the basic tartrate, hydrochloric acid, and hydrofluosilicic acid electrolytes. Deposits that are smooth and adherent can be obtained from these three electrolytes if low cathode current densities are employed. All three electrolytes were effective in purifying crude bismuth considerably, with additional purification indicated in each instance by a reelectrolysis step.With the basic tartrate electrolyte best results were obtained when the electrolyte was at 40° C. and contained at least 100 grams of bismuth per liter. An apparent disadvantage was depletion of bismuth from this electrolyte, causing the deposits to become spongy and nonadherent.The hydrochloric acid electrolyte had the greatest tendency to yield rough, dendritic deposits. Best deposits were obtained at cathode-current densities below 2 amperes per square decimeter. A small amount of glycerin helped to produce a smoother deposit, and adding sulfuric acid or methyl sulfuric acid retarded the deposition of impurities. Very good results were obtained in electrowinning bismuth from a bismuth trichloride-hydrochloric acid electrolyte.Smooth and adherent deposits were obtained from a hydrofluosilicic acid electrolyte, with very good refining as regards lead and silver impurities; however, higher reagent costs and slow decomposition of the electrolyte have discouraged its use.INTRODUCTIONMethods of recovering bismuth from ores and byproducts were underdeveloped for many years because of the limited uses for bismuth, the pharmaceutical industry being the chief consumer. In the past decade or so additional uses for bismuth, particularly in the metallurgical field, have brought about increased demand for the metal with the result that bismuth is being recovered from byproducts that were once discarded. In addition to such uses as low-melting alloys, solders, bearings, die setting, etc., some interest has been indicated in bismuth as a possible coolant for nuclear reactors. The advent of ductile bismuth and bismuth-alloy thermocouple wire has contributed greatly to temperature measurement, particularly in the below-zero range."

Jan 1, 1956

By James C. Church

The Bureau of Mines devised and demonstrated a portable linear cutting tester that directly measures and records the in situ cutting forces required of continuous-mining machine picks to it coal in underground mines. It requires only two operators to transport and operate the tester, which can be assembled and operated through a complete test cycle within a single mine work shift. This report reviews the factors considered in the design and development of the tester and the results of its system verification testing at coal mine sites.

Jan 1, 1985

In 2006, a total of 280 metal mining operations reported employment to the Mine Safety and Health Administration (MSHA).1 Metal mines were the smallest mining commodity sector, comprising 1.9% of all mining operations. ? Gold mines comprised 46.8% (n=131) of all metal mining operations. Other common types of metal mines were copper ore (n=34; 12.1%), and iron ore (n=33; 11.8%). Nevada had the largest number of metal mines (n=53; 18.9%), followed by Alaska (n=31; 11.1%).

Sep 1, 2008

According to contemporary psychophysical theory, the relationship between the strength of a perceived sensation (S) and the intensity of a physical stimulus (1) is best expressed by a power relationship.(1) S=kln (1) This psychophysical principle has been applied to many practical problems, including the development of scales or guidelines for effective temperature, loudness, brightness, and ratings of perceived exertion. Based on the results of a number of experiments using a variety of scaling methods and a number of different muscle groups, the pooled estimate of the exponent for muscular effort and force is 1.7.(2) When applying this principle to work situations, it is assumed that individuals are capable and willing to consistently identify a specified level of perceived sensation (S). For manual materials handling tasks, this specified level is usually the maximum acceptable weight or maximum acceptable force. These phrases are defined by the instructions given to the test subject:(3) You are to work on an incentive basis, working as hard as you can without straining yourself or becoming unusually tired, weakened, overheated, or out of breath. If the task involves lifting, the experiment measures the maximum acceptable weight of lift. Similarly, there are maximum acceptable weights for lowering and carrying. Such tests are isoinertial in nature; however, in contrast to the tests described in Chapter 3, they are typically used to test submaximal, repetitive handling capabilities. Data are also available for pushing and pulling. These are reported as maximum acceptable forces and include data for initial as well as sustained pulling or pushing. Why Use Psychophysical Methods? Snook identified several advantages and disadvantages to using psychophysical methods for determining maximum acceptable weights.(4) The advantages include: • Realistic simulation of industrial work (face validity); • Ability to study intermittent tasks (physiological steady state not required); • Results are consistent with the industrial engineering concept of "a fair day's work for a fair day's pay"; • Results are reproducible; and • Results appear to be related to low-back pain (content validity).

Jan 1, 1998

By Vibration Research Group, Natasha K. Lee Shee, Tammy R. Eger, James P. Dickey, Paul-Émile Boileau, Lana M. Trick, Michele L. Oliver

Introduction Industrial exposure to whole-body vibration is associated with injury and discomfort. Certain industries, notably mining, construction, and forestry, involve complex 6 degrees of freedom vibration. Laboratory-based studies of vibration are essential for controlled and systematic evaluation of the human responses to vibration2. The purpose of this pilot study was to evaluate whether the duration of the vibration exposure, and rest between vibrations, significantly influence the subjective ratings of comfort during laboratory-based studies of vibration. Methods Subjects: The cumulative vibration dose was calculated, and was below the health guidance caution zone recommended by International standards3. The experimental procedures were approved by the University of Guelph Research Ethics Board. Ten adult subjects participated in this pilot experiment. All subjects completed the entire experimental paradigm; no subjects complained of pain during or after the experiment. Experimental Design: The experiment consisted of four blocks of vibration exposures; either 15 or 20 seconds of vibration (1 df:Z axis, 3 df:XY plane, 3df:YZ plane, or 6 df) alternating with either 5 or 10 seconds rest. The order of presentation of the four blocks was randomized. Each of the blocks was composed of 37 individual sinusoidal vibration exposures in randomized sequence. This abstract focused on ten identical trials, (6.3 Hz vertical vibration, 0.55 m/s2 RMS) interspersed within each block, in order to assess whether the subjects’ comfort ratings systematically varied between the 15 or 20 vibration exposures, the 5 or 10 second rest between vibrations, or within each block. The experiment involved 43 minutes of vibration within the 62 minute experiment. Vibration Apparatus: A commercial parallel robotic platform was used to apply the specific vibration exposures (R2000, Parallel Robotics Systems Corporation, Hampton, New Hampshire). The subjects sat on a passenger seat from a 1992 Honda Accord that was rigidly mounted to the robotic platform (Figure 1). This robotic system performed the specific vibration exposures operating under closed-loop displacement control. A custom-written Matlab program automated the testing sequence.

Jan 6, 2006

By Dennis R. Dolinar

In general, the direction of the maximum horizontal stress in the eastern United States is fairly well defined. However, the variation of the magnitudes of the horizontal stresses is not very well understood. Because the horizontal stresses cause severe ground control problems in underground coal and limestone mines throughout the eastern United States a more complete understanding of how the magnitudes vary would be useful for developing mine design strategies to combat horizontal stress related ground control problems. Therefore, in this National Institute for Occupational Safety and Health (NIOSH) study, the variation of the magnitude of the horizon stresses in sedimentary deposits in the eastern and Midwestern United States are examined with respect to two factors, the elastic modulus of the rock and the site depth. Stress measurements from thirty-seven sites are used in the evaluation. Examining the applied excess strains indicates that the eastern United States can be, separated into high and low strain zones. For most of the eastern United States the maximum applied excess or tectonic strain ranges from only 300 to 550 micro strains. However, there is one area, a portion of the Beckley seam in the central Appalachian region where the strains are significantly higher than the other regions. In this higher strain zone, the maximum applied tectonic strains range from 700 to 1,000 micro strains. Regression models for each zone based on the elastic modulus can explain between 83 to 85% of the variation of the maximum horizontal stress. Because one region, the northern Appalachian district, has strains that are about 20% higher than the other regions in the low strain zone, multiple strain models based on geographic regions were developed for the low strain zone that can explain 87 to 91% of the maximum horizontal stress variation with the elastic modulus. Depth was found not to be a significant causal factor in any increase in the horizontal stress even though the site depths ranged from 275 to 2,500 ft. Beyond a theoretical increase, based on Poisson’s effect and gravity, no other increase in the horizontal stress with depth can be justified with this data. The most significant factor controlling the variation of the maximum horizontal stress is the elastic modulus of the rock, not the overburden depth.

By D. J. Donaven, Manuel Gomez, W. S. Landers

Bulk density tests were made on a Western U.S. coke oven plant blend to obtain bulk density control data that would be directly transferable to plant practice . Maximum bulk density values were obtained at zero surface moisture . Increase in surface moisture to about 6 percent decreased the bulk density to a minimum value . Increase in the fine grinding of the blend , at constant surface moisture , decreased the bulk density . The effect of oil on bulk density was observed with five oils at concentrations ranging from 1/8 to 1-1 / 2 gallons per ton . Maximum bulk densities were obtained within the 1 / 2- to 1 - gallon - per - ton range . Essentially the same bulk densities were obtained with petrolatum- and nonpetrolatum- containing oils . Storage effects were observed on samples tested at selected intervals from 0 to 56 days . No significant change in bulk density took place if no surface moisture was lost during storage .

Jan 1, 1964

By Alex C. Smith, Michael J. Sapko

A series of explosive detonation experiments was conducted in NIOSH’s Bruceton and Lake Lynn Experimental Mines to evaluate low level (<6 psig) detonation wave propagation behavior in single and multiple entry configurations. Entry cross-sectional area varied from 5 to140 m2 and explosive weights of Pentolite ranged from 0.24 to 2.4 kg. Behavior of the detonation wave was evaluated through recording of the pressure as a function of time and distance from the explosive detonation in single and multiple entry interconnecting tunnels. Peak pressure from detonation of an explosive in an underground mine maintains magnitude for a greater distance than is the case on the surface and is shown to follow the simple scaling rela-tionship P = 702.8(W/Vt)0.514(0.65)n, where P is the peak detonation pressure in kPa, W is the weight of the explosive charge in kg, Vt is the total volume in m3, and n is the number of splits, n = 0, 1, 2, …n. The total energy, or impulse, I, generated by these detonations can be expressed as I = 1.34(W/A)0.64n, where W is the weight of the explosive charge in kg, A is the area of the main tunnel in m2, and n is the number of side en-tries, n = 0, 1, 2, …n.

By Rita D. Sylvester

"IntroductionThe Bureau of Mines was established in the public interest to conduct inquiries and scientific and technologic investigations concerning mining and the preparation, treatment, and utilization of mineral substances; to promote health and safety in the mineral industries; to conserve material resources and prevent their waste; to further economic development; to increase efficiency in the mining, metallurgical, quarrying, and other mineral industries; and to inquire into the economic conditions affecting these industries. The organic act of the Bureau, as amended by Congress and approved February 25, 1913, made it the province and duty of the Bureau to ""disseminate information concerning these subjects in such manner as will best carry out the purposes of this Act.""In accordance with this directive, the Bureau reports the findings of its research and investigations in its own series of publications and also in articles that appear in scientific, technical, and trade journals; in proceedings of conventions and seminars; in reference books; and in other non-Bureau publications. The number of these reports, the wide range of subjects they cover, and the variety of mediums in which they appear make the kind of list and index presented in this special publication both necessary and valuable. This issue describes reports and articles published during the period January I, 1965, to December 31, 1969. It supplements the 50-year list of Bureau publications issued from July 1, 1910, to January I, 1960;' the 50-year list of articles by Bureau authors published outside the Bureau from July 1, 1910, to January I, 1960;3 the 5-year list of Bureau publications and articles from January I, 1960, to December 31, 1964.' It includes all the material in the four annual lists of Bureau publications and articles from January 1, 1965, to December 31, 1968, as well as the Bureau publications and articles for 1969."

Jan 1, 1970

By R. Karl Zipf, Z. T. Bieniawski

"Fracture mechanics plays an important role in studies of geologic materials such as rock and coal. Yet fracture data are scarce for rock and most limited or unreliable for coal. A testing system was developed which can apply mixed mode loads to a crack tip in many rocks and geologic materials. It is possible to subject the test specimen to pure mode I, various mixed modes and a nearly pure mode II fracture load. The system is currently used to study the mechanics of fine fragment formation in various coals. Experimental measurements include KI and KII' fracture velocity and acoustic emission.INTRODUCTIONA major research program at The Pennsylvania State University is directed to understanding the fundamental mechanics of fine fragment formation in various coals. The program represents an effort to reduce the incidence of coal workers pneumoconiosis (black lung) in coal miners. The principal source of the respirable coal fragments is the cutting operation which forms and liberates the particles by a fracture process. Present understanding of the mechanics of the events which form and liberate these particles is meager (Cook, 1982).Current knowledge of the fundamental mechanisms of coal dust generation and entrainment in terms of the underlying fracture mechanics is critically needed to improve and possibly control the processes involved. Whether the cutting operation is done with a 'continuous miner' cutting machine, a plow or a longwall shearer, it is fundamentally a problem of mixed-mode crack propagation. When a cutting tool interacts with coal, it causes numerous cracks to propagate through the intact material. Numerous larger fragments are broken free, but another quantity of undesirable fine fragments is also created. The formation of these respirable fragments may be a direct result of the crack propagation process; hence, a thorough understanding of the fracture mechanics of coal is required to minimize production of the unwanted fine fragments.In most rock engineering applications, the rock material properties are of secondary importance to the rock mass properties; however, for rock fragmentation and rock cutting problems, it is rock material properties such as fracture toughness which are of prime interest (Bieniawski, 1980). Several rock cutting and rock failure theories have been proposed, but it is only very recently that fracture mechanics concepts have been successfully applied to the study of rock cutting mechanics. All cutting models seek to predict the cutting forces and the cutter geometry necessary to cause rock breakage and chip formation given some fundamental mechanical properties ~f the rock. Such models have wide applications in drilling, tunnel boring and mining problems. Nelson et al., (1985, 1986) has provided a very useful correlation between the laboratory measured fracture mechanics properties of rock and the performance of the disk cutters on tunnel boring machines."

Jan 1, 1989

By John C. Machisak

INJURY DATA and experience at coal mines in the United States for 1957 are presented in this bulletin under the following general sections: (A) General injury experience: Tables 1-6: Current data on number of fatal and nonfatal injuries, frequency and severity rates, and average severity. (B) Selected injury experience: Tables 7-36: Current data on causes of injuries, distribution of injuries by part of body injured, days of disability, extent of hand and machine loading, experience by employ¬ment and production groups, and various other operating factors and physical conditions related to the occurrence of injuries at the Nation&apos;s coal mines. (C) Injury experience, by States: Tables 37-41: Data on injuries, injury rates, employment, causes of injuries, and severity rates. (D) Major disasters: Table 42: Data on major disasters from 1948 to 1957. A major disaster is defined as a single accident in which, or as a result of which, five persons or more are killed instantly or die at any time thereafter. (E) Historical coal-mine-fatality experience: Tables 43-47: Data on fatalities and their causes at bituminous-coal, lignite, and anthracite mines from the earliest records through 1957.

Jan 1, 1960

By L. A. Neumeier

The Bureau of Mines evaluated the properties and anisotropy in properties of rolled Zn-Cu and Zn-0.12 pct Ti-Cu alloys with various copper additions to 1.25 pct. The alloys were rolled cold and at various hot-rolling temperatures to reductions as high as 92 pct after breakdown rolling. The properties are extremely sensitive to various combinations of composition, rolling temperature, and rolling reduction, Zn-Cu alloys can develop good creep resistance, but they are inferior in that respect to Zn-Ti-Cu alloys. For alloys either with or without the titanium addition, cold-rolling results in recrystallization of the matrix and rejection of copper from solution, causing poor hardness, tensile, and creep properties, but high ductility. Peak tensile strengths develop when the alloys are rolled in the range 320° to 400° F, Best creep resistance for Zn-Cu alloys requires higher rolling temperatures when copper content is increased. Creep resistance is best for Zn-Ti-Cu alloys with about 0.75 to 1.0 pct CU rolled near 480° F. Some copper is soluble in the TiZn15 phase, which forms into "stringers" during rolling. The possible contributions to creep behavior of factors such as distribution of second-phase particles, grain size, and preferred orientation are discussed.

Jan 1, 1970

By F. E. Walker

The Bureau of Mines determined total sulfur and sulfur forms for coal in 283 counties in 29 States and 2 fields of the State of Alaska. Specifically, organic, pyritic, and sulfate sulfur were measured of approximately 2,900 samples, and they include most of the coalbeds in the United States.

Jan 1, 1966

By F. E. Walker

The Bureau of Mines determined total sulfur and sulfur forms for coal in 283 counties in 29 States and 2 fields of the State of Alaska. Specifically, organic, pyritic, and sulfate sulfur were measured of approximately 2,900 samples, and they include most of the coalbeds in the United States.

Jan 1, 1966

By D. L. Nussear, W. E. Wallace, N. N. Clark, M. Gautam, G. Hong-Guang

"Results from a study directed towards identifying and measuring the mutagenicity of diesel exhaust particulate matter involved in mining exposures, especially those which may synergistically affect genotoxic hazard, are presented in this paper. Particulate matter emissions from a diesel engine, representative of the ones found in underground mines, were sampled and assayed to determine the genotoxic potential as a function of engine operating conditions. Diesel exhaust was diluted in a multi-tube mini-dilution tunnel and the particulate matter was collected on 70 mm fluorocarbon coated glass fiber filters as well as on 8"" x 10"" hi-volume filters. A six mode steady state duty cycle was used to relate engine operating conditions to the mutagenicity potential.Protocols developed for using a primary component of pulmonary surfactant as a medium for collecting and applying respirable particulate material to cells for mutagenicity testing offer a true representation of in-vivo delivery of such respired aerosols to pulmonary cells and the genetic material within . The surfactant dispersion technique is discussed in this paper. Methods have been developed to sample and assay the diesel soot and diesel soot/mineral dust complexes which would not compromise the surface and physical properties of the particulate material."

Nov 1, 1995