Search Documents

By Lowell B. Moon

The Stange and Byrnes Heirs manganese mines, adjoining properties in Bland and Giles Counties, Va., have produced at least 20,000 long tons of concentrates containing 8,000 long tons of manganese. They were selected as the site for a strategic-mineral development project because of the existence of geologic possibilities for extensions of the known ore body. In plan, the long dimension of the ore body parallels the axis of a major anticline. Localization apparently is due to longitudinal and transverse fracturing incident to two-way folding. That the manganese oxides were deposited by downward-moving solutions is suggested by the fact that mineable concentrations are confined to a coarse, porous sandstone under-lain by impervious silt and clay. Bureau of Mines project work began on January 15, 1941, and was completed on April 23. The work sampling the faces of the pit, bulldozer trenching, and churn drilling. Pit sampling consisted of 132 channel samples usually 5 feet long and taken at 20-foot intervals. Seventeen trenches aggregating some 4,500 feet in length were dug by the bulldozer. Trenches averaged 12.6 feet in width and 5 feet in depth. A total of 1,978 feet of churn drilling was done in 33 holes. In preparation for churn drilling it was necessary to construct roads to 21 of the 33 sites. A total of 2,867 linear feet of road averaging 13 feet in width was built.

Jan 1, 1950

By Robert M. Koerner

The feasibility of using small-scale models to simulate residential masonry foundation walls subject to fatigue loading was investigated. Five wall segments were modeled in one-quarter scale using dynamic similitude equations. The walls were dynamically loaded using a sinusoidal base motion and wall accelerations were monitored. The stiffness, natural frequency response, and damping characteristics were measured. The number of cycles of testing necessary to cause initial visible cracking was recorded. Analysis of the data indicated the importance of the relationship between the forcing function and the natural frequencies of the structure in influencing cracking damage.

Jan 1, 1980

By S. Raghavan

An investigation of the possibility of improving the grinding characteristics of a gabbro ore containing copper and nickel sulfides via a thermal shock treatment technique has been carried out. The results obtained indicate that the breakage characteristics of the gabbro are particles can be significantly improved by preheating the are particles to a temperature around 400°C followed by rapid water quenching. For a given power input and feed size, the thermally treated material produces a product of much finer distribution than the untreated material. An assessment of the improvement in grindability has been made by calculating feed size selection functions for untreated and heat-treated materials.

Jan 1, 1981

By D. W. Blaylock

1. The Lower Freeport and Lower Kittanning beds are the most important beds in Clearfield County, Pa., from the standpoint of production. The Lower Kittanning bed has the largest remaining recoverable reserves of any of the beds in the county. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 short tons per acre-foot of coal in place, are estimated at 1,909 million short tons as of January 1, 1953. Of this total, 1,177 million short tons is in beds 28 inches and more thick. Areas in some beds were omitted from the estimate because available data relative to the bed characteristics are too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1955

There has been a substantial increase in the use of rubber-tired front-end loaders in the mining industry in recent years. Concurrent with this increased usage, in the period of 1966 to 1970, there were at least 74 mining industry fatalities involving front-end loaders, or (on the average) in excess of one fatality per month. When the usage of front-end loaders by the construction industry and other industries, organizations, and agencies, such as the Government (i.e., Department of Defense), along with the uncounted numbers of serious, but non-fatal accidents, are included in the picture, the safety record for front-end loaders, of necessity, becomes a serious subject for study. There is an urgent need for attempts to be made to eliminate or reduce the number of safety hazards; to decrease the confusing diversity of controls designs found on present front-end loaders; to improve the maintenance and operating procedures; to formulate better personnel policies; to increase management and official awareness of the extent of the problem, in both industry and the Government; etc.; in order to decrease the number of accidents. Part of the problem may be traced to the fact that the operator of a front-end loader is frequently designated a "heavy equipment operator." This implies that he is automatically qualified to operate any model, of any manufacturer's, wheeled or tracked, front-end loader as well as many other types and classes of heavy equipment. Contrary to automotive practice, the complement of primary operating and emergency controls varies widely from model to model, as well as from manufacturer to manufacturer. Not only are certain controls present on one front-end loader model and absent on others, but there are significant differences in the modes of control operation, in the functions performed by superficially similar controls, in the location of the various controls, etc.

Jan 1, 1973

By Eric S. Weiss

The National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) conducted joint research to evaluate explosion blast effects on typical U.S. mine ventilation stoppings in the NIOSH Pittsburgh Research Laboratory?s (PRL) Lake Lynn Experimental Mine (LLEM). An innovative Australian-designed brattice stop-ping was also evaluated. After mine explosion accidents, MSHA conducts investigations to determine the cause(s) as a means to prevent future occurrences. As part of these postexplosion investigations, the condition of underground stoppings, including the debris from damaged stoppings, is documented as evidence of the approximate strength and the direction of the explosion forces. The LLEM data showed that a typical dry-stacked and coated solid-concrete-block stopping survived a total explosion pressure of ~6.7 psi (~46 kPa) and was destroyed at a total explosion pressure of ~7.6 psi (~52 kPa). In comparison, a typical dry-stacked and coated hollow-core concrete block stopping survived a total explosion pressure of ~3.4?4.3 psi (~23?30 kPa) and was destroyed at a total explosion pressure of ~3.6?5.2 psi (~25?36 kPa), depending on the length of the pressure pulse and the value of the pressure-time integral. A typical steel panel stopping design survived a total explosion pressure of 0.8 psi (5.5 kPa) and failed at a total explosion pressure of 1.3 psi (9 kPa). The LLEM data also showed that an obstacle blocking the path of a pressure wave resulted in a higher reflected pressure at the obstacle. An 8-in (20-cm) thick wet-laid solid-concrete-block stopping coated on one side survived a total explosion pressure of ~26 psi (~180 kPa); this stopping was not tested to failure. A 6-in (15-cm) thick wet-laid solid-concrete-block stopping coated on one side survived a total explosion pressure of ~14 psi (~97 kPa) and was destroyed at a total explosion pressure of ~25 psi (~172 kPa). An innovative Australian woven cloth stopping survived an explosion pressure of 4.0 psi (27 kPa) and was destroyed at an explosion pressure of ~6.1 psi (~42 kPa). These results will help investigators determine the approximate explosion forces that destroy or damage stoppings during actual coal mine explosions.

Jan 1, 2008

By G. Richards Gwinn

The mineral graphite, a form of carbon, has been known for hundreds of years, and, was first used commercially as a coloring agent. Its true identity, however, was not recognized until the end of the eighteenth century, and its commercial development did not become extensive until near the close of the ninteenth century.

Jan 1, 1943

By Laxman S. Sundae

A Bureau of Mines investigation was conducted to determine the effect of specimen volume on the apparent tensile strength of disks of St. Cloud Gray Granodiorite, Lithonia granite, and Rockville granite. The investigation used a technique developed by the Bureau to determine apparent tensile strength. Because the test specimens were selected without macroscopic defects, that is, cracks, joints, and planes of weakness, the strength variations are solely due to microscopic features. Several replications of each test were performed. Data for each set of specimens were fitted to a power law of the form y = axb, where y = apparent tensile strength, x = specimen volume, and a and b are constants. This power law is essentially a form of Weibull's theory. The average coefficients of correlation for St. Cloud Gray Granodiorite, Lithonia granite, and Rockville granite were 0.85, 0.53, and 0.78, respecitvely. In all cases a decrease in strength with increasing volume was noted; in the extreme case, a decrease of 40 pct was noted with an elevenfold increase in volume. The decrease in strength with increasing specimen volume is explained in terms of Weibull's theory.

Jan 1, 1974

By Otto Ruhl

The zinc-lead ore reserves of the Tri-State district of Kansas, Missouri, and Oklahoma, as of December 31, 1947, are estimated at a total of 66,100,000 tons of crude ore containing 2.18 percent metallic zinc and 0.38 percent metallic lead. The Bureau of Mines began estimating the reserves in October 1945 and completed the' work December 31, 1947. A total of 38,900 acres of land representing approximately 5 percent of the area of the district is covered in this report. The work was confined for the most part to properties developed or partly developed by drilling and underground workings, and to acreage sufficiently drilled out to indicate ore of enough tonnage to make a commercial undertaking. The acreage in which ore reserves exist is widely distributed in all three States. A map of the Tri-State area is shown in figure 1. The remaining 95 percent of the area is not necessarily nonproductive but represents, possibilities for future exploration and development of additional mineral resources when and if economic conditions or national necessity encourage such work. Of the total reserves, 41 percent are in Missouri, 38 percent in Kansas, and 21 percent in Oklahoma.

Jan 1, 1949

By L. Kaufman

Fifteen boride composites were synthesized by hot pressing and evaluated by physical and incendivity testing as non-sparking tool materials. The incendivity tests, conducted at the U. S. Bureau of Mines, Albany Research Center, compared the boride compo-sites with standard cobalt-bonded tungsten carbide material used for coal cutter bits. Two titanium diboride composites and two zirconium diboride composites out-performed cobalt-bonded tungsten carbide in wear resistance and reduced tendency to cause ignitions. However, three of these candidates exhibited undesirable chipping. The remaining candidate, a TiB2-(Ni, Cu) composite, did not chip, nor did it cause ignitions at levels where cobalt-bonded tungsten carbide tools caused ignitions in the incendivity tests. Thus, this material appears to be a logical candidate for further development.

Jan 1, 1973

By J. Fletcher Smoak

The value of abrasive materials consumed in the United States increased 37% in value over that of 1983 to $439 million; of which, 58% was manufactured abrasives, 36% was industrial diamond (natural and synthetic), and 6% was natural abrasives. Production value of natural abrasives, which consist of crude tripoli, special silica stone, garnet, and emery, increased 4% Production of crude tripoli, a finely disintegrated chert, increased 12% in quantity and 8% in value. Shipments of processed tripoli increased only 3% in quantity but increased 16% in value, with large increases occurring in both major end-use categories. Production of garnet, an abundant iron-aluminum silicate, decreased slightly in quantity and value after posting continued increases in quantity and value since 1980. There was a significant decrease in the quantity and [ ]

Jan 1, 1985

By B. J. Dalton

The Bureau of Mines Helium Activity has developed a computer program for use in the reduction of pressure-volume-temperature (PVT) data obtained with a Burnett compressibility apparatus. This program includes important modifications and extensions of some of the methods currently used for treating these types of data and yields statistical information that cannot be obtained from any other published work. The methods of calculation make use of a general nonlinear least-squares technique developed at the Helium Research Center. Because of a need to investigate different functional forms for representing the compressibility factor isotherm, 2, the computer program has been written in such a way that the only additional coding required is the so-called compressibility function subroutine. This subroutine defines the analytical form of Z and certain of its partial derivatives. The program described herein is believed to be the most advantageous for use in treating isothermal Burnett compressibility data.

Jan 1, 1970

By H. A. Watson

Laboratory tests on three commercial methane detectors, two combustion- type detectors and one interferometer-type detector, were made by the Bureau of Mines to determine their response to certain single and multiple flammable gases mixed with normal and abnormal air atmospheres. Although both types of detectors responded accurately to methane-normal air mixtures, they did not show correct concentrations for other single flammable gases in air. Uniquely, the response of the interferometer-type detector to hydrogen was in a negative direction. The effects of individual gases in multiple flammable gas mixtures were approximately additive. In oxygen-deficient atmospheres the methane response of the interferometer-type detector erred on the high side, but only in very low oxygen concentrations were the combustion-type detectors affected-- showing low, erratic methane readings.

Jan 1, 1966

By Jack O. Jones

The Furnish mine, Caharrus County, W. C., was operated intermittently until 1905 as a gold mine. Scheelite was discovered by A. L. Mash in the mine dumps of the Furniss and Phoenix mines, and he later informed the Bureau of Mines of his discovery. The Bureau of Mines, in two projects at the deposit in 1948 and in drilled 12 holes totaling 1,706.6 feet, examined and sampled the underground workings, excavated by bulldozer and hand, 3,155 linear feet of trenches and collected numerous samples for assay. The best scheelite shown; was found in the underground exposure of the Furniss mine.

Jan 1, 1950

This briefing was sponsored by the Bureau of Mines to summarize ongoing and recently completed chromium-chromite research and resource assessment activities by the Bureau. Through the series of 18 presentations compiled herein, Bureau personnel covered a wide range of topics including U.S. chromite and chromium trends and usage patterns; foreign and domestic resources; and research activities on mineral characterization and beneficiation, chemical and pryometallurgical processing of chromite and chromium-bearing wastes, new low-chromium alloy and coating substitutes, corrosion- and oxidation-resistant stainless steels, and chromium-containing refractories.

Jan 1, 1986

By A. N. Baldwin

This report documents the work performed under Bureau of Mines Contract J0265029 to study and develop two innovative mining systems: ? An underground auger capable of augering into the right and left ribs without repositioning the machine ? A conventional mining system employing recently developed innovative machinery. The report is separated into two volumes to document the two studies separately. Volume I describes work performed and the recommended concept for a bidirectional auger. Volume II describes the studies of mining equipment performance and mining plans developed to determine a conventional mining plan offering improved productivity.

Jan 1, 1977

By John M. Devine

Hydrogen sulphide associated with natural gas was noted as early as at Point Albino, Canada. The presence of this impurity was recognized also in other of the earlier oil and gas fields, although the occurrence was by no means common. However, in recent years, with the development of the producing zones of test Texas and the Texas Panhandle, the Production of "sour" crude has increased greatly and hydrogen sulphide has proved a generally troublesome factor--frequently a major problem--in the drilling and operation of many wells in those areas. The problems arising from the drilling and producing of oil or gas wells in hydrogen-sulphide areas, fall under two general divisions: safety problems and corrosion problems. Mention is made of a third division which is closely related to the other two, that of treating--or the development of processes for the removal of hydrogen iron the standpoint of safety and health hazards, hydrogen sulphide in the petroleum industry has been discussed in a number of publications. Likewise, the problem of hydrogen-sulphide corrosion of production equipment has been given considerable attention in the literature.

Jan 1, 1931

By W. I. Watson

The study considered all the institutional, resource reserve, technological, and economic factors relevant to the industry's present and future status, such as markets and marketing techniques, competition from other producers both domestic and foreign, federal and state regulations affecting the industry, quarrying and processing technologies, slate reserves and resources, and industry structure and economics. Constraints to the growth of the industry were assessed and scenarios proposed to solve some of the problems.

Jan 1, 1980

By M. L. Bowser

Pulse-forming circuitry is described for use in explosives research that requires precise synchronization and control of events in order to investigate detonation parameters. Included are pulse generators for oscilloscope sweep control, counterchronograph actuators, and a raster-type oscillographic method for the determination of velocities of detonation that are applicable to studies on solid, liquid, and gaseous detonations. INTRODUCTION Prom time to time, requests have been received for information on electronic circuitry used in explosives work at the Explosives Research Laboratory, Bruceton, Pa. The methods used are not entirely original;4 5 6 however, modifications of earlier techniques and some novel design aspects have resulted in time-tested methods that warrant a more detailed description.

Jan 1, 1962

By Walter E. Lewis

The Fort Randall Reservoir project, on the Missouri River at Pickstown, S. Dak., was designed by the Corps of Engineers and is part of the Missouri River Basin Development Program. The location of the project with respect to adjacent features is shown' in figure 1. When the project is finished, it will include a large earthwork dam and 12 circular tunnels, 8 of which will be equipped for power and 4 for flood control. Various phases of the construction have been contracted to independent companies, and at present four companies are working on different phases of the project under a rigid time schedule. Western Contracting Corp. is the contractor on stage II, earthwork; Johnson-Winston Construction Co. is the contractor for construction of the intake towers at the upstream side of the dam; McCarthy Improvement Co. has the contract for the power house and the outlet works on the downstream side; and Silas Mason Co. has the contract for driving the power and flood-control tunnels. The latter two companies use the same roads for ingress and egress to their respective work areas and the same general waste dump area. Under such circumstances, it is necessary that each company stay on a time schedule in regular sequence to avoid interference with the other.

Jan 1, 1951