Search Documents

By X. Q. Wu

Magnetization in slurry (MIS) of weakly magnetic minerals by iron ions was investigated. The magnetic seeds (strongly magnetic particles) were synthesized by ferruginous chlorides directly in slurry instead of previous preparations of magnetic seeds by finely grinding mineral magnetite or specially synthesizing them separately in an aqueous solution. In this way, the growth of the seeds and their adsorption on the minerals simultaneously take place in the same slurry. That after MIS the recovery of weakly magnetic mineral limonite in a magnetic separator increased means the formation and adsorption of magnetic seeds on the surface of iron mineral limonite. The magnetization effect was evaluated by limonite recovery at a magnetic strength of 3.500 Gs in a magnetic separator. Mineral limonite was properly magnetized in the following slurry condition: molar ratio of Fe3+ to Fe2+1:3, slurry temperature of 45 °C and pH 10.5. The selectivity of the magnetization between minerals limonite and quartz was improved by adding surfactant sodium oleate.

Jan 1, 2014

By Tom Liu

This paper is a fundamental study of bubble-particle collision efficiency in turbulent flows. A CFD-based microscale scheme for the prediction of turbulent bubble-particle collision efficiency in a 3D isotropic turbulent flow is developed, and in this way, turbulence effects on particle-bubble collision efficiency are taken into account for the first time. By comparing the computed results with experimental data from the literature, the CFD simulation is shown to correctly predict the bubble-particle collision efficiency in a quiescent environment. The CFD method was then applied to the investigation of bubble-particle collision efficiency in a turbulent flow, and the simulation results are shown to be qualitatively consistent with the real observations. The predicted collision efficiency can be used in a multiscale modelling scheme, which would account for all control variables in a flotation cell, such as impeller structure and tip speed, air nozzle structure and air flow rate This study indicates how microscale simulations of bubble and particle behaviours, coupled to macroscale CFD simulations of flotation cells, can provide a powerful tool predicting the flotation rate in a real flotation cell.

Jan 1, 2014

The simulation study on the process of iron ore beneficiation plant of Essar Steel, Kirandul was carried out. The iron ore fines and slimes generated nearby Bailadila mines of NMDC are used as raw materials for this beneficiation plant. The capacity of the plant is 1400 TPH operating in parallel in two streams. The capacity of the plant was utilized about 60% of throughput capacity. To improve the plant capacity as well as quality performance, the simulation study was conducted to detect the bottleneck of the process. The process samples were collected from input and output of each processing unit operation to generate the data base for simulation study at the feed rate of 400 and 500 TPH of iron ore fines in a single stream. The characteristics data i.e., breakage and selection functions were generated using MILLSOFT package for simulation of ball mills. Then MODSIM package was used to evaluate the performance of each unit operation to identify the bottleneck. It was established by a simulation study that the intermediate thickener draws high current when the feed rate is more than 400 TPH due to high torque drawn by rotating rake because of presence of coarse particles in the input stream to thickener. The problem was sorted out by classification of input stream of thickener to remove the coarse particles. Then the process was simulated at its rated capacity, and experimental validation studies at the plant were also conducted at the feed capacity of 600 and 700 TPH by modification of process flowsheet. The experimental data was almost matching with simulated data. Finally, the processing plant is running with full rated capacity without any bottleneck. Keywords: simulation of ball mill, breakage function, selection function, iron ore

Sep 1, 2012

By Felipe Henríquez, Daniel Silva

"Traditionally, the implementation of an automated advanced process controller in any mineral processing complex is a challenge, mainly due to the quality of resources and technologies required, the uniqueness of each control solution and the uncertainty of the engineering hours needed to complete the task. Thus, the use of advanced and proven control technology becomes a key factor when deploying the control strategy. However, success would still not be possible without the presence of common sense, process knowledge and fundamental process data. Minera Los Pelambres, taking advantage of such factors and its accumulated process experience, implemented a novel and successful combination of MPC (Multivariable Predictive Control) and advanced control for secondary grinding and regrinding stages at its copper concentrator plant. In both cases, the control objectives are: being capable of processing a variable feed from the upstream process while at the same time avoiding to become a process bottle neck and yet, maintaining an adequate product quality (in terms of size distribution) to the process downstream. Additionally, for the case of the vertical regrinding mill (vertimill), the control system should also be capable of keeping an adequate circulation load and making an efficient use of the available grinding power. In either case, extending hidrocyclones availability while maintaining their performance is a must, since both factors are required for process and maintenance purposes. Thus, the process control problem becomes one with a multi-variable type of process with multiple control objectives to satisfy simultaneously. In trying to solve it, many mineral processing operations have implemented basic or conventional control or even better yet, expert systems. Minera Los Pelambres believes that better and faster results can be achieved using a combination of MPC and advanced control. Such strategy was successfully implemented, reducing considerably process variability while maintaining high throughput and keeping the process well within constraints limits. Their control philosophy, implementation process, main results and their key performance indicators are discussed here."

Jan 1, 2014

By Mohsen Hashemzadehfini

Nowadays heap leaching has become established as a mineral processing technology for treatment of some low grade minerals such as copper, gold, and zinc, etc. Heap height, particle size, leach reagent consumption, and metal recovery are four important metallurgical parameters in a hydrometallurgical process like heap leaching. This paper investigated the effects of heap height and particle size on copper recovery as well as acid consumption. Three heap heights of 2, 4 and 6 meters and two particle size fractions of less than 25.4 mm and 50.8 mm were selected as variables in the experiments. The research results showed the inverse relation between heap height and copper recovery as well as acid consumption. Under given conditions, the copper recoveries of minus 25.4 mm ore are 78.63%, 66.27% and 52.88% higher than that of minus 50.8 mm samples for the heap heights of 2, 4, and 6 m, respectively. Both copper recovery and acid consumption increase with decreasing particle size. Keywords: heap leaching, heap height, particle size, acid consumption

Sep 1, 2012

By P. A. Bepswa

A numerical study done to test the efficacy of heuristics developed for the design of measurement networks for high precision metallurgical accounting is presented in this paper. The heuristics considered were designed to maximise variance reduction of terminal stream measurements through data reconciliation for observable linear flow systems. A complex metallurgical process flow sheet from the mineral sands industry was used as a case study. Monte Carlo type simulations coupled with a non-linear programming based steady state data reconciliation algorithm were used as tools to investigate the heuristics. The results obtained suggested a close correlation between magnitudes of measured variances and the respective levels of variance reduction obtained through data reconciliation for both internal and terminal streams. It was observed that variance reduction through data reconciliation was maximised for terminal stream measurements in networks characterised by high precision measurement of internal streams and/or in flow sheets characterised by high ?stream to node ratios?. Terminal streams attached to highly interconnected parent nodes were observed to experience higher reductions in variance compared to terminal streams attached to less interconnected parent nodes. The results generally highlight the additional benefits of highly interconnected flow sheets and high precision internal stream measurement regimes on the maximisation of variance reduction of terminal stream measurements through data reconciliation. These findings are significant to metallurgical accounting and to process accounting applications in general in that they provide a conceptual basis for design decision making regarding the construction of measurement networks aimed at maximising variance reduction of targeted streams through data reconciliation.

Jan 1, 2014

By Partha Patra

Numerous proteins of varying properties are available in extracellular bacterial proteins (EBP) isolated from Paenibacillus polymyxa. EBP was fractionated through ammonium sulfate precipitation in a controlled fashion and characterized through SDS-PAGE technique. Different groups of proteins, (Group A~D) exhibited varying degrees of surface affinity to minerals such as quartz, pyrite, chalcopyrite, galena and sphalerite. Interaction with mineral specific bioproteins rendered pyrite and chalcopyrite hydrophilic while surface of quartz, galena and sphalerite turned more hydro-phobic. Specific groups of proteins could thus be used for selective separation of galena, sphalerite and quartz from pyrite and chalcopyrite (as a mixed sulfide) through microbially-induced flotation or selective flocculation.

Jan 1, 2014

By Sami Makni, Ahmed Bouajila

"To remain competitive in an open market, mining companies are more and more requested to optimise their complex and highly multivariate processes. The increasing amount of process data, brought about by intensive use of instrumentation and the progress in computer data acquisition, enhances the need for more and more powerful and robust tools for the analysis and modelling of the process data. Now, with the emergence of multivariate data analysis (MDA) techniques, on-line clustering of mineral process behaviour is possible and could help in the extraction of valuable process operation indicators. MDA can be used in different mineral processes such as flotation, grinding, smelting etc.In this paper, we focus on grinding process considered as the most costly and power consuming node of the mineral processing scheme. Different objective-oriented levels of data clustering will be addressed.First, the evaluation of grinding operation taking into account data and constraints from all processes before (e.g. blasting, crushing) and after (e.g. flotation, leaching, etc.) the grinding node. The second level deals with process diagnosis by differentiating operation level and identifying behaviour drifts. Control and optimisation are two other levels concerned here with the selection of optimum trajectories in the drift correct.Industrial plant data are processed in order to illustrate the feasibility and the potentiality of MDA applications in addressing the clustering and interpretation of grinding mill behaviour."

Jan 1, 2003

By Z. F. Dai

The Thompson Nickel Belt, located in Northern Manitoba, Canada, contains more than 400 million tonnes of ultramafic low-grade nickel mineralization in 9 deposits. One of these, the Pipe deposit, was mined between 1971 and 1983 producing a Ni concentrate of 9% to 11% grade at 73% recovery. The operation was terminated because the poor recovery, low Ni grade and high MgO con-tent of the concentrate made processing this ore uneconomical at the metal prices prevailing at that time. Vale Inco is now re-evaluating these deposits with the intent of providing a new source of concentrate for its Thompson integrated processing facility. It is known that serpentine slimes coating on the sulphide surfaces are responsible for the poor metallurgy. Various desliming methods were tested including settling, elutriating, tabling and hydrocycloning. Hydrocycloning has proven to be the most effective means of desliming. With a feed assaying 0.70% Ni and 33% MgO, a rougher flotation concentrate assaying 22.7% Ni and 4.8% MgO was produced at a Ni recovery of 62.5% (relative to the feed to grinding), with no utilization of slimes dispersants. Another 16.6% Ni recovery was achieved in scavenger flotation resulting in a total Ni recovery of 79.1%. Batch flotation tests using various flowsheet configurations to optimize the grinding, desliming, reagentizing and flotation conditions are in progress.

Jan 1, 2014

By Y. G. Zhu, G. B. Zheng, Z. B. Qian, X. R. Zhang, A. J. Ren

"Based on PMA polymer, two kinds of novel macromolecular depressants, PMTA and PMA-PDTC, were designed and synthesized. PMTA was used for desilication in hematite reverse flotation. PMA-PDTC was used in the separation of Cu-Pb concentrate as galena depressant. The micro-flotation results showed that PMTA exhibited a good depression performance compared to starch. We found that 98.29% of hematite was depressed with a grade of 65.24% at pH 11 with 12 mg/L dosage. The flotation separation results of Cu-Pb concentrate demonstrated that PMA-PDTC was an effective depressant for galena in separating galena from chalcopyrite. When IPETC was used as collector, at pH 8.5, the flotation separation tests demonstrated that Cu concentrate was obtained with a grade of 28.89% containing 12.12% Pb.INTRODUCTIONThe role of depressants is crucial in the separation of oxide or sulfide minerals, for example, the desilication in hematite concentrate and the separation of Cu-Pb concentrate.It is well known that, in current reverse flotation processing of hematite, starch is a traditional depressant for hematite. Most research focus on the modification of starch [1-3]. Although its depressing ability is enhanced in some extent, its own shortcomings is still existed. So, it is important to develop a new hematite depressant instead of starch.In the separation of chalcopyrite and galena, because of their extremely similar floatability, it is difficult to realize the separation of these two minerals. Traditionally, there are two methods widely used in the separation of Cu-Pb concentrate by depressing chalcopyrite with cyanide [4] or depressing galena with dichromate [5] in most cases. However, these two inorganic depressants are toxic and hazardous. Their use could cause heavy pollution problems and a large loss of precious metals. In order to adapt to the requirements of sustainable economic development and environmental protection, the research and development of green and environmental depressant has gained more and more significance."

Jan 1, 2018

By Xubo Chen, Zhiqiang Hu, Zhijian Sun, Gaoyun Zhou

"The research aimed at developing an efficient and environmental frother,which was applied in the flotation of sulfide ores. The flotation properties of an efficient frother and pine oil have been studied relatively by flotation tests of lead and zinc sulfide ores. At the same time, the biodegradability of two kinds of frother has been studied by the method of biological respiratory curve. The test results show that the flotation properties of new frother are superior to pine oil such as flotation rate, dosage etc. and its biodegradability is superior to pine oil. INTRODUCTION Frother is a kind of important agent in flotation reagents.In practice, the criterion of the foaming performance of the frother is what is high and low according to flotation indexes. The difference of different minerals and flotation technologies has great influence on the foaming performance of frother, and it is very important to choose the corresponding frother. The type, dosage and selectivity of frother in flotation process must be considered carefully. In today's society, environmental protection and ecological protection are becoming more and more important, and the environmental and ecological damage from mine development has aroused increasingly more attention. The use of mine agents has promoted the development of mineral resources, greatly improves the recovering utilization of mineral resources, at the same time, the production and use of mine reagents also inevitably bring about pollution, and result some influence or damage in the ecological environment.The frother is a common kind of reagent in the flotation process of the concentrator. In many cases, the waste water in the concentrator can not be let out in the natural water because the higher content of the frother in the waste water results in higher index of COD.This will inevitably increase the cost of waste water treatment in the mine.Therefore, the choice of frother should not only consider its influence on the flotation index, but also consider its influence on environmental protection. Waste water treatment is a way to solve the waste water pollution, but it needs to cost a lot of fund, manpower and material resources.And the development of high efficiency pollution-free reagent is a good way to reduce the production cost of mining enterprises and reduce the environmental pollution."

Jan 1, 2018

By Ranjeet K. Singh

Kelsey Centrifugal Jig was found to be promising for the beneficiation of fine coal particles. The present study was aimed at in-depth understanding of the separation features of Kelsey Jig through detailed experimentation. Beneficiation of fine coal of size 150 x 300 µm was studied in a laboratory Kelsey Jig. The thickness of the ragging bed is found to be an extremely crucial parameter apart from the other process parameters such as rotational speed and pulsation frequency. A constant pulp density (25% solids) of the feed slurry was maintained in the study. The feed rate was also kept constant at 50 kg/hr dry solids. Silica sand of size -1.68+0.85 mm was used as ragging material to avoid the pegging of internal screen having an opening of 425 µm. The rotational speed was found to have significant effect on the depth of the ragging bed and its porosity, which influenced the separation performance considerably. Pulsation was identified as the key factor in stratifying the coal bed and defining the misplacement as well as ragging bed porosity, which influenced the mass yield and quality of the products. Beneficiation studies were carried out with rotational speed varying between 900-1000 rpm while pulsation frequency was kept within 850-925 rpm. In a single pass through the Kelsey Jig 7-8% (absolute) reduction in the ash content of the feed material was observed at more than 55% mass yield. High rotational speed, moderate pulsation, and low ragging bed depth favored good cleaning. A high bed depth was found to facilitate rejection of high ash materials. It was established that Kelsey Jig is effective in fine coal cleaning though a controlled operation is required in order to achieve superior performance. Keywords: enhanced gravity separator, g-force, separation performance, ragging material, coal beneficiation

Sep 1, 2012

By Al Cropp, Julie Hunt, Will Goodall, Ron Berry, Dee Bradshaw

Geometallurgy aids the understanding of ore body variability but has the most value if the data is easily available along the entire mining value chain. This requires cross-discipline communication and collaboration across traditional silos, and an organizational culture that encourages that to flourish. Data that are collected by the numerous groups (i.e. mining, geology, milling, processing, refining, smelting, marketing, environmental etc.) involved in the mining process may have relevance to other stakeholders; mineralogical and textural data for example has value to all these groups. Data required for modeling comminution or identifying acid potential from waste rock may already exist, however it needs to be made available to all the relevant stakeholders in the right format at the right time. As part of the GeM (AMIRA P843 & P843A) project the opportunity has been taken during the sponsor meetings, short courses, case studies etc. to ask the question: ‚What information do you want from further up the chain?? For example, to metallurgists ‚What information would you like from the geology group before the ore enters the mill?? The geology group may already have information important to mineral processing but not know it is of interest. This could, for example, be in the form of a geometallurgical drill core log that contains quantitative measured values. This paper focuses on the interaction between the mining, geology, mineral processing and environmental groups, using ore properties resulting from geological alteration to identify potential impacts throughout the mining process and discusses how a cross discipline approach can benefit all.

Jan 1, 2014

By Xing Yang, Zhen Peng, Guangwen Zhang, Haifeng Wang, Yaqun He

"Triboelectric separation of ilmenite ore based on the tribocharge differences between ilmenite and gangue minerals was conducted in this study. Triboelectric characteristics of ilmenite and its associated minerals were studied using polyvinyl chloride (PVC), pentatricopeptide repeats (PPR), copper, polymethyl methacrylate (PMMA), stainless steel (SS), teflon and quartz glass (QG) tribochargers in lab triboelectric unit. Results demonstrated that the ilmenite particles tribocharged positively while gangue minerals tribocharged negatively using PVC as tribocharger. The particle size also has a significant effect on tribocharge, and the -0.125+0.074 mm is the optimal size fraction of triboelectric separation. Charge-mass ratios of minerals increase with the increases of tribocharging length, but the increasing rate gradually reduce. At 1.5 m tribocharging length, charge-mass ratios of ilmenite, quartz, feldspar and mica are up to 6.07 nC/g, -6.05 nC/g, -4.30 nC/g and -4.56 nC/g, respectively. Based on the triboelectric characteristics of each mineral, triboelectric separation of ilmenite was conducted, and the grade of ilmenite ore increased from 15.47% to 28.40%. INTRODUCTION As a transition metal titanium plays an irreplaceable role in medical, aerospace and materials due to its light weight, high strength and corrosion resistance. Pure titanium dioxide is an excellent white pigment and is widely applied in industries of paint and textile. Ilmenite is the main raw material for titanium industry. For the beneficiation of ilmenite, series methods have been proposed, such as the application of dry magnetic and wet gravity separations to separate the ilmenite from the zircon and rutile. Electrostatic separation is extensively used in the beneficiation of heavy mineral sands for the recovery of rutile, zircon and ilmenite while flotation is used to separate fine ilmenite (Mehdilo et al., 2014; Fan et al., 2014). Compared with flotation and gravity separation, electrostatic separation does not consume water, and native properties of materials will not be changed and energy consumption will be reduced (Wang et al., 2014). Thus, the wide application of electrostatic separation and other dry separation methods is a trend in separation and purification industry, especially in water-scarce areas."

Jan 1, 2018

By I. Gombköto

In the EU-region, the automatically operated approximately 200 (rotating hammer) shredder plants processing large technical equipment (end-of-life vehicles, large household appliances) annually produces 8-9 million tons of non-metallic grinded by-product, which ends in landfills, without recovery. Although this by-product is organic material, still contains large amount of metal components worth recycling. These operations, such as shredding and processing end of life vehicles or mixed metal components are a growing market and it is become more potential if EU directive 2002/96/EC will become obligatory for new member and candidate countries and they have to apply EU regulations. Eddy current separators (ECS) are one of the most important units of separation of non-ferrous metals from insulators in waste recycling. The product of ECS processing of shredded ELV?s is usually a mixture of Al, Cu, Brass and stainless steel. This mixture has relatively low price on the market, while purified metal products are required by smelters for which shredder operators are able to get even higher price. Our aim at University of Miskolc was to find solution producing pure metal products using dry separation processes. Authors are presenting a possible solution, using ECS. Institute of Raw Material Preparation and Environmental Processing possesses an ECS, equipped with 305 mm wide belt, and a concentric magnetic rotor. The subject of our work was to investigate the behaviour of model particles with different shape, conductivity (aluminium and brass), orientation and size in order to separate Al and Brass. We used model particles with similar shapes of shredder plant originated ones. The magnetic flux and magnetic frequency was constant and derived by the design of the rotor. During our research work, belt speed and rotor speed of ECS were varied. The particle distance and trajectory caused by throwing was determined and the results are reported in this paper.

Sep 1, 2012

By V. Sheikhzadeh, M. Saghaeian, R. Hejazi, A. Abazarpoor

The research aimed to compare the chemical analysis (K, Na, Cl) of Iranian concentrate plants, which are the main source of materials corrosion in the pelletizing plants. Cl alongside alkaline elements (especially K) may cause corrosion and plug in the grate plates and other involved equipment. Therefore, it is tried in the processing plants to remove impurities from the concentrate to prevent potential problems in pelletizing and iron/steel making processes. Part of these impurities are existed in the nature of ores and others are sourced in the processing water. Various samples from the largest Iranian concentrate plants including Chadormalu, Gol-e-Gohar, Jalal-Abad and Sechahun were prepared to investigate the possibility of alkaline problems for each samples. The amount of Cl, K and Na of Chadormalu sample was obviously low and therefore no alkaline problem is expected. The Cl content of Gol-e-Gohar sample was high (980 ppm) while amount of K was less (0.008 Wt. %). Due to low content of K, most of Cl will release as Cl2 or HCl and so problems caused by KCl plugging would not be a problem. The amount of Cl in Sechahun case was nearly same as Jalal-Abad (400-600 ppm), higher than Chadormalu and less than Gol-e-Gohar samples. However, the K content was higher than all samples (0.04 Wt. %). Therefore, the amount of evaporated K would be 2-4 times more than other samples. Since the amount of Cl and K is simultaneously higher than usual iron ores, therefore alkaline problems may be a serious prevention factor for the continuous operation of this plant. In order to solve this problem some counter-measures is suggested and discussed including cleaning system, partial dust enriched with KCl removal and variation in the materials type of involved equipment.

Jan 1, 2018

By Zhou Junwu, Han Long, Song Zhenguo, Sun Chuanyao

The deposit genesis, the ore property, and the mineral characteristics, which has a close relationship with the beneficiablity, could be regarded as the “Genetic Properties”, actually are the determining factors for beneficiation process development. However, in conventional concentrator’s process development and engineering, there have been lack of systematic research and test on those genetic properties, also lack of well-established collecting, statistics and analysis system for those huge amount of data such as the historical mineral processing technique research, process mineralogy study, practical operating and engineering data. Obviously it is far less than enough for profound integration combining modern IT together with traditional mineral processing technology, as a result there are a number of disadvantages in mineral processing R&D and engineering, such as long term, high cost, low efficiency as well as repetitive testwork not making full advantage of previous experiences. Aiming to make utmost of those Genetic Properties and overcome above disadvantages in mineral processing R&D and engineering, the concept of “Genetic Mineral Processing Engineering (GMPE)” is put forwarded, and the strategical study has been conducted on this regard, with the main focus on following aspects: a) Testing and extraction of the “Genetic Properties”; b) Establishment of data base and data warehouse of GMPE; c) Intelligent decision making system for beneficiation process; d) Verification testwork; e) Virtual concentrator. The technical route proposed is to firstly conduct research and test on those Genetic Properties mentioned above, based on that the specific data base will be set up and applied for intelligent process recommendation and simulation with a few verification testwork conducted in the meantime, finally achieve a fast, high efficiency and precise determination of technology and process for ore beneficiation. The systematic study on the three-in-one GMPE would make an innovative breakthrough in conventional mineral process testwork research and engineering methodology, and provide technical support for the concentrator’s design and upgrading.

Jan 1, 2018

By Rob Morrison, Andrew Scott

"Long before a modern mine commences operations it has already become a wealth of information. After start up, it can generate enormous quantities of data - especially with semi-automated data acquisition by instrumented mine equipment.However, much of this data is of limited use for evaluation of (potential) performance unless it links in some way to the site business model.An underlying reason for this waste of data is that the different cultures, financial, technical, community, environmental, etc, not only have many areas of interest but also have very different conceptual models by which they evaluate performance.It is too ambitious to attempt to bring all of these cultures together - in a single step.However, the success of the Mine to Mill - project has demonstrated that substantial operational value can be added by using a more integrated approach to comminution. The next logical step is to integrate measurement and then to track performance from ore body model to saleable product and waste disposal. From resource to product also represents a path from very sparse, highly variable data to much more detailed measurement and more representative sampling.However, in both cases the data collected is strongly focused on the technical requirements - not on the business model.This paper considers how to define at least some of the key decision points in terms of some case studies.Performance data from many areas might be used to derive simple models which can then be used for forecasting and optimisation of planning."

Jan 1, 2003

In the present work, the flotation behaviours of zircon, rutile and ilmenite using sodium oleate as collector in absence and presence of depressants were thoroughly investigated. The maximum in the flotation recovery of any of the above minerals falls within similar pH ranges. A range of inorganic and polymer depressants were examined in order to improve the separation of zircon from rutile and ilmenite. Optimum values of conditioning pH and depressant concentration to achieve maximum recovery and best selective floatability of zircon were obtained. Selective flotation of zircon from Ti-bearing minerals was anticipated from single mineral experiments under different pH values, depressant and collector conditions.

Jan 1, 2014

By P. T. L. Koh

The effect of particle shape on the flotation process has been investigated in laboratory experiments with monosized spherical ballotini and roughly ground ballotini. The particles were treated by partial methylation with trimethylchlorosilane to achieve varying degrees of hydrophobicity. In flotation, the process of film thinning and liquid drainage is critical in the formation of a stable bubble-particle attachment and this is affected by the particle shape and surface hydrophobicity. The rate of attachment affects the overall flotation rate. Flotation tests with different particle sizes at various degrees of partial methylation have been performed in a modified Denver cell. Predictions from a computational fluid dynamic model of the cell which incorporates fundamental aspects of bubble-particle attachment are compared against flotation test results. Contact angles of the particles have also been measured using the capillary rise technique to indicate surface hydrophobicity.

Jan 1, 2014