Search Documents

By E. M. De Souza, J. F. Archibald

This paper examines aspects of Canadian mine backfilling operations that may be implemented to assist in reducing solid waste production, lowering energy costs, and restricting Greenhouse Gas emissions. Many Canadian underground mines use backfill to mitigate environmental effects associated with tailings disposal. Backfill production and disposal are energy intensive processes that require an average energy cost of 37.7 MJ/tonne of backfill to complete. Mine backfills, in engineering applications, also commonly make use of cement as a stabilizing agent. Cement requires an additional energy cost ranging between 4,637 and 6,600 MJ/tonne to produce. The large energy needs associated with mine backfilling and cement production operations create significant CO2 and Greenhouse Gas emissions. Approximately 1 tonne of CO2 and Greenhouse Gas is emitted for each tonne of Normal Portland Cement produced. For single mines producing 3,000 tonnes of backfill per day, considering both backfill and cement emission source terms, total emissions of CO2 ranging between 120.36 tonnes and 169.44 tonnes/day are anticipated. In Ontario, mining operations contribute 700,000 - 840,000 tonnes/year of CO2 and Greenhouse Gas emissions to satisfy backfill cement consumption needs alone. Potential reductions of cement in backfill would significantly reduce emission of these gases and lower their adverse environmental impacts. This paper identifies alternate, equally effective and lower cost binder agent strategies for cement in backfill that may lead to cement consumption reductions. Post-consumer glass represents one such potential alternative backfill binder. Over 950,000 tonnes of glass are disposed of annually in Canada, two-thirds of which exists in the form of easily recoverable glass packaging that is not currently recycled or reused. The partial replacement of cement by waste glass may address goals for reducing non-recyclable glass waste disposal; enhancing mine back filling operations; reducing total backfill energy costs; and ultimately reducing Greenhouse Gas emissions levels currently generated by the Canadian mining industry.

Jan 1, 2004

By R. H. Watson

A paper read by J. A. H. Church before the Northern Alberta Branch last February described a method of working thick inclined coal-seams from the dip upwards, with the view to preventing fire risk by using water for the stowage of waste workings, and extinguishing a conflagration should such break out, was favorably received; but there was some doubt as to the cost of such a method, as it involves a retreating system, which might prove too expensive for practical adoption. Let us consider a typical leasehold such as we are familiar with in the Rocky Mountains. The leasehold is crossed at one end by a mountain river, which is cut by the outcrop of a seam of coal, 30 feet in thickness, pitching as shown on the drawing herewith, which also shows the general line of the outcrop in elevation through the leasehold, which is two and a half miles long and contains 1,500 acres. The average lift is about 600 feet above river level and drilling has proved that the coalseam can be tapped at a depth of 1,500 feet, 2,000 feet down the pitch from the outcrop in the river, all as shown in the illustration, which is typical enough of our mountain conditions to serve the purposes of comparison of methods. We take up the leasehold and invest $30,000 to pay for drilling and prospecting; $30,000 more for the price of the lease to locator or holder, and say $100,000 to pay for a railway spur (it might cost twice this sum, but we are only comparing two methods in the same location) and "now we are ready to consider equipment and the cost of development.

Jan 1, 1924

By M. Souley, G. Armand, M. Ghoreychi, D. Seyedi, J. -B. Kazmierczak

"An anisotropic constitutive model is proposed in this paper accounting for both structural anisotropy and induced anisotropic plasticity. It is assumed that the rock is composed of a matrix and of potential planes of weakness. The matrix is assumed to be linear, transversely isotropic and the plasticity is described by a non linear yield function where the parameters are deduced from the nonlinear Hoek-Brown envelopes in pre- and post-peak, and derived from the laboratory characterization. A non-associated flow rule is used with a distinction between compression and extensional stress paths, as well as the absence of volumetric strain beyond large plastic distortion.The planes of weakness are considered as known a priori or assumed to be oriented perpendicular to the direction of the current minor principal stress. An elastic-perfectly plastic behavior according to the Mohr-Coulomb criterion is assumed in the planes of weakness; while the elastic part is considered as linear and transversely isotropic.Finally, the proposed model was implemented in FLAC3D and used to simulate triaxial compressions to provide a verification of the implementation. The applicability of the implemented model to reproduce damage (pre-peak) and/or failure developments around a circular opening is checked. The GCS drift, one of the mine-by experiments set up at the main level of the Meuse/Haute-Marne Underground Research Laboratory, is selected for this first application."

Jan 1, 2015

By F. T. Manns, G. Harper

"The Swayze gold mine is an Archean vein deposit in northern Ontario. The veins are superimposed on a conjugate joint system and are contained within an anastomosing alteration envelope in a metadiorite body. Reserves were estimated on the basis of fire assays of channel samples and car load samples from underground mine openings, surface and underground diamond drilling and surface trenching. A semi-variogram constructed from channel samples along one of the drifts yielded a horizontal, regionalized influence of approximately 9.0 m. Common industry practice has been to use 6.1 m for similar deposits in Ontario. Proven ore was defined from underground openings. The maximum extrapolation distance for proven ore along strike and dip from a data point is taken to be 6.1 m. Probable ore is extrapolated 7.6 m from a data point in a mine opening or from a drill intersection. Possible mineralization is based on geological continuity one-half the distance to a neighbouring data point.The mineral inventory estimate of 1.45 million tonnes at a grade of4.8 g Au/tonne gives an excellent outline of the geology of the deposit. The deposit contains 313 000 tonnes of ore reservesat a fully diluted grade of6.9 g Au/tonne. These figures include dilution for several reasons: (I) a 2.1 m mining width is used rather than the more typical 1.5 m width to allow for over break because of the shallow dip of some vein zones; (2) over break is allowed for adjacent to major unmineralized dykes; and (3) grams of gold are deleted from estimates to allow for the mining of unavoidable minor dykes.A personal computer with off-the-shelf software was used to compile 712 geologically defined ore blocks and sort them into a number of revealing categories. The computer was used to perform grade sensitivity tests, as well as to evaluate depth potential. Hopefully, the reiterative aspect of the method has randomized the errors and helped to cancel their effects."

Jan 1, 1987

By A. B. Walker

The effects of the injection of dry limestone additives into boilers for the sorption of sulphur dioxide have been studied in pilot and full-scale systems. The effects of such injections on boiler mass particulate emissions as well as collectability characteristics of the fly ash and reaction products are presented. Implications of the effects on the design and economics of particulate collectors, in particular electrostatic precipitators, are discussed.

Jan 1, 1971

By Yoshimasa Funakawa, Kazuhiro Seto, Akio Kobayashi

A new hot rolled high strength steel consisting of ferrite matrix and nanometer¬sized precipitates was developed. The ultra fine precipitates were identified as TiMoC2, and the strengthening by the precipitates was evaluated more than 300MPa in case of TS/800MPa grade steel. Due to the strengthening effect of the ultra fine precipitates, alloy elements for solid solution hardening can be reduced. It is notable that the steel shows very high yield strength (730MPa in case of TS/800MPa) and very high local elongation leading to excellent stretch flange formability at the same time. The mechanical properties of the steel are attractive for chassis parts and structural parts of auto body. The steel has been produced commercially, and applied to the parts successfully.

Jan 1, 2004

By Hermann A. Derbuch

Twin Mining made a conscious decision when it changed from gold mine explorer and developer to become a diamond explorer in Canada?s Arctic. It was a decision of survival in an environment that saw junior gold companies either disappear or turn into dot com companies. Twin Mining learned fast and staked within weeks of that decision the first 50 sq. km of claims on, what became, its TORNGAT property at 59½° latitude on the east coast of the Ungava Bay in northern Quebec. This land position, 724 diamonds later (including 322 macro diamonds of gem quality, white and transparent) grew to 507 sq. km today. The 74° latitude called when Twin Mining exercised the option to acquire 3 claims owned by Helix Resources Inc. which revealed exceptional diamond potential. A gem quality 5.4 mm (0.768 carat white and transparent) diamond and the discovery of 16 pipes on 15.2 ha convinced Twin Mining?s board to sanction the deal. Both properties have outstanding features. Kimberlite Dykes and Pipes are in outcrop. The property locations have deep-sea access near existing infrastructure. Their locations are in an environment that is stable and development friendly and has a positive track record with successfully operating mines near-by.

May 1, 2001

By John Redstone, André R. Laplante

"Le rebroyage des concentrés d'hématite en usine (Sidbec-Normines, Port-Cartier) et en laboratoire a été modélisé selon le modèle de Reid (1965).L'effet du pourcentage solide sur la cinétique de broyage a été étudié en usine. La fonction de sélection corrigée (pour tenir compte de l'effet du pourcentage solide sur le temps de rétention) augmente lorsque le pourcentage solide augmente de 80 à 84 pourcent. Cette amélioration est contrebalancée par une augmentation de la quantité de pulpe court-circuitée, à des pourcentages solides supérieurs a 81%. La densité optimum de broyage se situe à 84 pourcent.Comme alternative au mode d'opération actuel, l'assemblage des broyeurs en série plutôt qu'en parallèle a également été simulée. Le moins 44 µm passe alors de 68.1 à 72.5 pourcent, ce qui correspond à une capacité supplémentaire de 32 tonnes à l'heure par broyeur. Ces résultats doivent toutefois être interprétés avec prudence, car la cinétique de broyage n'est généralement pas linéaire lorsque le taux d'alimentation est plus que doublé.IntroductionL'usine de bouletage de Sidbec-Normines Inc. a été décrite par Morimoto (1977), Lévesque et al. (1979) et Pabst (1979). La section de broyage des concentrés contient six broyeurs à boulets en parallèle et en circuit ouvert, d'un diamètre de 5. 18 mètres et de 10.36 mètres de longueur. Ils contiennent chacun environ 350 tonnes de boulets d'acier forgé de 3.8 cm de diamètre. Le concentré est broyé de 10 pourcent moins 150 µm (100 mailles) à 65-68 pourcent moins 44 µm (325 mailles), à un pourcentage solide de 78 à 80 pourcent. Cette fragmentation poussée exige une consommation d'énergie de 32 kWh/tonne. Cette énergie est surtout libérée sous forme de chaleur, la pulpe étant déchargée a une température de 68-72° C. II en résulte un milieu de broyage corrosif, et une consommation de boulets élevée, de 3.4 à 4.0 kg / tonne broyée."

Jan 1, 1983

By Northeastern University, B. Y. Cui, B. Y. Wang, D. Z. Wei, W. G. Liu, Z. C. Guan, S. L. Gao

To recover iron values from low grade ores by reverse froth flotation method, further research on cationic collectors used in reverse flotation of iron ores is launched to promote the utilization efficiency of iron ores. In this paper, one new cationic surfactant, bis(2-hydroxylethyl) dodecylamine (BHD), that could be dissolved in water easily was used as collector for quartz flotation. Flotation results indicated that BHD shows stronger collecting performance on quartz than hematite. The maximum recovery of 96.30% to quartz is obtained at a collector concentration of 20.0 mg/L in the pulp pH range from 5 to 7. This collector can be used to float quartz from hematite. And optimal separation results with 86.59% iron recovery and 66.60% iron grade to synthetic sample were achieved at a collector concentration of 20.0 mg/L and pulp pH of 5.02 when hematite and quartz were mixed at a mass ratio of 3:2. The adsorption mechanism of the collector on quartz surface was investigated by XPS analysis, infrared spectroscopic analysis and zeta-potential measurements, which revealed that electrostatic attraction and hydrogen bonding adsorption occur between collector and quartz surface.

Jan 1, 2016

By O. G. Olvera, L. S. Quiroz-Castillo, P. J. Valenzuela-Guerrero, D. G. Dixon

The effect of sulfuric acid concentration on the extractions of arsenic and copper in the catalyzed batch leaching of an enargite concentrate was studied. The acid concentrations studied were 60, 45, 30 and 15 g/L. The experimental series yields maximum copper extractions of 96 to 98% in an interval of 81 - 185 h leaching time for 60 - 15 g/L initial sulfuric acid concentration; all the copper extractions plateaued after these values; the rates and plateaus of copper extraction are increased with higher acid concentrations. Arsenic extractions reached maximum values of 89% in 57 hours, 57% in 49 hours, 33% in 25 hours, and 25% in 112 hours respectively; these maximum values were followed by a steep decrease in arsenic concentration, which indicates a precipitation event occurs in the process. According to the literature and process conditions, the arsenic precipitates obtained are iron arsenates similar to scorodite. The stability of the residues was tested using the Toxicity Characteristic Leaching Procedure (TCLP) from EPA; the residues for the four concentration levels passed the TCLP test, reporting arsenic leaching values below 1 mg/L.

Jan 1, 2014

By S. Hunt, S. Jayasekera, J. Kyle, N. Perera, K. Stone

A preliminary investigation has been conducted to determine the conditions for the precipitation of phosphate from the liquor produced after a hydrochloric acid pre-leach and rare-earth recovery from a rare earth containing fluorapatite concentrate from the Nolans rare earth deposit in the Northern Territory of Australia. The results show that at 50oC the phosphate can be precipitated in two stages using limestone to produce a Stage 1 precipitate containing most of the impurities including iron (94%), aluminium (92%), fluoride (98%), uranium (84%) and thorium (94%), followed by a relatively pure Stage 2 dicalcium phosphate precipitate (DCP) containing only 0.05% Fe, 0.05% Al, 0.1% F, 0.01% U, and <0.01% Th. The initial Stage 1 precipitate contained about 25% of the phosphate while the remaining 75% reported to the Stage 2 phosphate precipitate. Depending on the required radioactivity specifications, the amount of phosphate in the Stage 1 precipitate could be reduced. Reagent requirements were 11.4 kg limestone (as pure CaCO3) per cubic metre of solution for the Stage 1 precipitate and 39.7 kg limestone (as pure CaCO3) per cubic metre for Stage 2. The analysis of radionuclide balance indicated that radionuclides deported mainly to the final filtrate (86.4%) compared to Stage 1 precipitate (5.4%) and Stage 2 precipitate (8.2%). Settling and pressure filtration tests indicated the precipitates were both readily settled and filtered. The final moisture contents of the Stage 1 and Stage 2 precipitates were 62.5% and 49.3%, respectively.

Jan 1, 2014

By J. D. Wright

This paper describes current milling practice at Endako Mines Ltd., a molybdenum producer in central British Columbia. The various steps in the crushing, grinding and flotation of the ore are outlined, with emphasis on the metallurgy of the latter operation. Tailings disposal and concentrate assaying methods are also described.

Jan 1, 1969

By S. R. Noble, F. R. Harris, E. T. C. Spooner

"The Logtung deposit discovered in 1976, is an example of large tonnage (162 million tonnes), low grade (0.13% WO3 and 0.052% MoS;) W(scheelite)-Mo mineralization related to multiple felsic intrusions. Because mineralization is predominantly fracture-controlled (> 95 %) rather than disseminated, Log tung is not a skarn deposit. Metamorphism of the Logtung country rocks (interbedded calcareous shale and graphitic quartizite) to a series of competent reaction skarns (quartz-diopside-garnet calc-silicate, biotite quartzite and wollastonite-vesuvianite calc-silicate) clearly precedes W-Mo mineralization. Hence mineralization was related to permeability created by hydraulic fracturing and not replacement processes.Logtung shows a theme of several phases of mineralization (4) related to multiple intrusions (>2) which is similar to that of the Climax and Urad-Henderson Mo systems. The earliest quartzmolybdoscheelite vein system, which consists of a typical ""porphyrystyle"" crackle-breccia of thin (0.5 mm to 4 mm) quartz-garnetdiopside- molybdoscheelite veins, is related to a high Si02 (approx. 76%), seriate-porphyritic monzogranite stock (approx. 2 km by 0.5 to 1 km) of Cretaceous age (118 ±2 Ma [2u]; Stewart, 1983). Later quartz-pyrite scheelite (fluorite-KINa-feldspars-molybdenite) veins, with prominent green, hornblende-bearing alteration selvages, and quartz-molybdenite (-pyrite-jluorite-scheelite) veins are related to a quartz-feldspar-spessartine-rich garnet porphyritic felsic dike complex approximately 500 m across. Both intrusive phases have anomalously high Wand Mo concentrations of about 100 ppm and 50 ppm respectively, which Stewart (1983) attributes to a primary enrichment. The final stage of mineralization consists of a prominent 4.5 km by 1 km zone of 1 em to 1 m wide polymetallic sheeted veins centred on the felsic dike complex. The system is zoned from quartz scheelite-molybdenite-pyrite-blue-green beryl-jluoritebismuthinite veins in the core to Pb-Zn-Ag veins with abundant arsenopyrite and minor Sn (approx. 0.1%) in the northeast. The focus of recurrent intrusive and hydrothermal activity was located above a flank or nose of the monzogranite stock.The distribution of WO3 and MoS2 grades within the approximately 750 m (across) by 300m (evaluation depth) mineralized zone is a result of the variable superimposition of the four separate vein systems each with different W:Mo ratios. Well-defined Wand Mo ore, shells such as those at Climax, Henderson and Mt. Emmons did not develop at Logtung. The upper surface of the mineralized zone, as shown by the 0.03% MoS2 contour defines an elongate dome with an apical region approximately coincident with the felsic dike complex. Hydrothermal alteration occurs as well-defined vein selvages, and not as pervasive zones.The Logtung deposit shows many similarities to porphyry Mo deposits in the western Cordillera and may be identified as a porphyry W(scheelite)-Mo deposit, with a W:·Mo ratio of 3.3:1. The principal reasons are: (1) mineralization is spatially associated with porphyritic granitic intrusions and (2) much of the scheelite and molybdenite occurs in typical ""porphyry-style"" vein stockworks"

Jan 1, 1995

By Adrian E. Scheidegger

"AbstractThe possibilities of deriving pertinent information about fractures in an oil pay from data obtained by core analysis are investigated. It is shown that it is possible to obtain an estimate of the fractured area per unit volume of the pay, and that the size of the fractures can be estimated if their shape is known. A suggestion of a routine procedure for the analysis of fractures is given.1.-IntroductionMany oil fields are producing essentially from cracks or fractures. Where this is the case, it is important to be able to obtain a knowledge of the size and distribution of those fractures in the oil pay. This knowledge has to be derived from the analysis of cores taken from the fields, as it is generally impossible to follow a fracture through the pay by direct means. The necessity of using statistical methods to extrapolate the meagre information obtained from the cores of the wells is therefore indicated.It is known that the fractures are much bigger than the diameter of the cores; thus, if they strike a core, the latter will generally fall into two pieces. The angle of the fracture with the vertical can be measured and, if oriented cores are taken, the exact position of the surface element representing the intersection of the fracture with the drill stem can be determined. Sometimes the edge of a fracture can be seen in a core. The number of •Cores that show such an edge can be noted. Of course, one has to be careful to distinguish between original fractures in the pay and fractures in the core caused by drilling operations. Only the former are relevant."

Jan 1, 1955

By Brian W. Mackenkzie, Jozef Lajzerowicz

This paper is intended to familiarize planners in the noncommunist world with the district planning approach used in eastern Europe for mining development. It deals generally with the basic nature of the district planning problem, the planning process for mining development and the state organization for the planning of mining districts. A number of applications of district planning techniques to both established and new eastern European mining districts are described.

Jan 1, 1971

By Y. Duna

The reliability of mine ventilation systems is critical to normal and safe production in a mine and includes reliability of the following parts: ventilation system branch (or passage), ventilation structures, ventilation network, and the fan. Among these, the reliability of a ventilation branch may be considered the foundation of the whole ventilation system. The branch ventilation flow includes four parameters: air volume; toxic and hazardous gas concentrations; temperature, and dust concentration. The calculation model for the reliability of a branch was established based on the analysis of normal distribution of flows in any one branch. Then, the efficiency of the ventilation structures and fire risk compromising the reliability of branch was studied. The results obtained were as follows: if the air volume, toxic and hazardous gas concentrations, temperature and coal dust concentrations of the branch are within reasonable limits, set at any stable state and at the same time, then this branch is reliable.

Aug 1, 2013

By Marc C. Bétournay

A number of successful proof-of-concept projects have been carried out to replace conventional power application, such as diesel and rechargeable batteries, in underground mine vehicles. This has led to the development of the world?s first fuelcell production vehicle, a mine locomotive. A mine loader project has also started and several other projects are planned. These projects are providing the mining industry with the required information to make this technology shift possible. The application of fuelcell power will yield several important benefits such as the elimination of underground diesel emissions, significant reduction in the primary extraction?s sector greenhouse gas emissions and support for a more productive scenario. This article reviews these successes, discusses ongoing and potential projects and presents the technology application benefits that could be possible for mining operations.

May 1, 2003

By S. Eckert, M. Reuter, D. Obiso, S. Kriebitzsch, M. Akashi

The present paper focuses the application of CFD techniques to investigate the Top-Submerged- Lance (TSL) gas injection in liquid metal. Previous works of the authors have shown that up- and down- scaling procedures based on the modified Froude number have some shortcomings, as this approach does not take into account the interfacial and viscous forces. Indeed, surface tension and dynamic viscosity of the smelting slags (σ = 0.4-0.5 N/m, μ = 0.2 Pa·s) are higher than the operating fluids that have been used in literature (water, paraffin oil) to study TSL injection in down-scaled furnaces. In order to get closer to real systems, the authors study the TSL injection of Argon in a liquid metal. An experimental campaign was carried out in the X-ray lab at Helmholtz-Zentrum Dresden-Rossendorf (HZDR), where the eutectic alloy GaInSn was used as liquid phase. The alloy is liquid at room temperature, and X-Ray imaging is used to picture the multiphase flow in a quasi-2D vessel. The aim of the present work is to demonstrate the applicability of CFD techniques to model multiphase flows involving liquid metals, and validate the model using the data produced at HZDR. The commercial software ANSYS Fluent® was used together with the Volume of Fluid model to directly resolve the gas-liquid interphase. Some features of the flow, such as the void fraction distribution and bubble detachment frequency are tracked with CFD and compared to the experimental data. INTRODUCTION In the last thirty years the TSL smelting technology has increasingly been used for industrial non- ferrous smelting processes and is now one of the significant pyrometallurgical processes. Developed in the early 1970’s at CSIRO, the furnace is nowadays commercialized in different market sectors, including copper and lead smelting, zinc fuming, waste treatment and slag recovery (Floyd, 2005). Despite the wide application of these reactors in the pyrometallurgical market, some aspects of the process are still not fully clarified, since in-situ measurements and optical accesses are prohibitive because of the high temperatures and aggressive conditions. Phenomena such as the bubbling regime, the slag solidification and the submerged combustion still need a deeper scientific investigation to obtain a better understanding of the process.

Jan 1, 2019

By A. Saigal

The effect of temperature on the cutting forces during machining of alumina reinforced aluminum composites was investigated, Aluminum 6061, 10% Al2O3 reinforced composite and 20% Al2O3 reinforced composite were tested, A 5/8-inch diameter high-speed steel end mill, a Micro 100 TiN coated single edge endmill cutter and a two-fluted solid carbide insert cutter were used for tooling, The results, in general, showed an increase in the cutting forces as the temperature of the material increased, From the raw data, there are temperatures ranges in which the force data did decrease but they were insignificant with regards to predicting a downward trend. A regression analysis was used to understand which variables had the greatest affect on the forces being generated, The correlation and regression analysis showed that at 600 rpm (velocity: HSS- 98,2 sfpm, Micro 100 cutter - 78,5 sfpm, solid carbide cutter - 192,4 sfpm) the tooling, the workpiece material, built up edge, and temperature were statistically significant factors in the test, Tooling was a significant variable in all testing, The smallest forces recorded during machining were generated with the solid carbide two-fluted endmill cutter, Visually, the solid carbide tooling produced a better surface finish during the testing which made it the tool of choice, In addition, the force data proved that as the cutting speeds were increased, the cutting forces decreased.

Jan 1, 2005

By M. Yavuz

As a branch of Operations Research, decision making is a widely used application in both science and social sciences. There are many different methods developed to solve decision making problems in the literature. In this study, Fuzzy Analytic Hierarchy Process (AHP) method is performed for the selection of reclamation project selection in an open pit mine and the optimal solution of the problem is investigated. Different reclamation project alternatives are prepared for an open pit mine, which continues to its production activities in magnesite sector in Turkey. The data obtained from Magnesite Cooperation is used in the application of the method. A decision-making process is prepared as considering the project alternatives for the purpose of selecting the most suitable reclamation project. The entire criteria that affect the decision-making process are identified and transformed into a hierarchical structure. The problem is solved by using Fuzzy AHP method developed according to this structure. It is found that Fuzzy AHP is a method that may help decision-makers in solving different decision-making problems in mining.

Aug 1, 2013