Search Documents

By Champoux. G., E. Ghali, W. Zhang, G. Monteith, A. -M. Lafront, G. Houlachi

The efficiency of the electrowinning process of zinc depends on the performance of oxygen evolution reaction, anode quality and corrosion resistance of lead anodes. Original surfaces of rolled commercial lead-silver anodes were examined using conventional polarisation methods in acid zinc sulfate electrolyte with manganese sulphate at 38 °C. The self-discharge method (potential decay) following 5 h polarisation at 50 mA cm-2 was considered to evaluate electrochemical activity, oxygen overpotential and anode stability. The influence of silver content is compared to that of the microstructure, the fabrication process and the composition of the corrosion products. Polished anode samples have also been examined for microstructural and corrosion performance studies. The experiments show that the duration of the plateau at 1600 mV versus SHE, the potential level (active corrosion state/stationary state) and the rate AEco/At during the decay could be a good indicator to compare the corrosion rates of the anodes in industrial zinc electrolytes.

Jan 1, 2008

By Jin Li

The tensile properties and microstructure of AZ91 Mg alloy before and after equal channel angular extrusion (ECAE), and the fracture behavior during tensile testing for as-extrusion and ECAE AZ91 were investigated. The alloy was performed ECAE from one to eight passes at 498K. The elongation decreased with the pass number increasing after ECAE. Grains were refined, partial coarse ß-Mg17Al12 phase fell to pieces, fine ß-Mg17Al12 precipitated in the AZ91 Mg alloy after ECAE. During tensile test the a-Mg/ ß-Mg17Al12, a-Mg/Al8Mn5 interface and the grain boundaries in a-Mg matrix acted as the crack initiation sources. The frequency of micro-cracks at the a-Mg/ß-Mg17Al12 interfaces and grain boundaries increased after ECAE, which accelerated the growth and coalescence of the micro-cracks during tensile test and resulted in the decrease of elongation of AZ91 Mg alloy by ECAE.

Jan 1, 2006

By Lise-Aurore Lapalme

Structure of the Presentation ? sustainable development and its social dimension ? challenges that mining is facing ? responses by industry ? corporate social responsibility ? the role of government Sustainable Development ? new perspective on how we view development ? consider how minerals and metals contributes to sustainable development ? challenge to better understand economic, environmental and social aspects ? make social aspects more broadly understood and appreciated

May 1, 2002

By R. Noorani, M. Cai

"Excavation of deep underground openings in highly stressed grounds can generate new fractures near the openings. As a result, rock mass bulking may occur, leading to large wall deformation. A better understanding of brittle rock failure and the associated fracturing process at the laboratory scale is an essential step towards evaluating dilation behavior of rocks. A grain-based model that can capture dilation behavior of rocks under various loading conditions at the laboratory scale can be a useful approach to study rock mass bulking at the field scale. The aim of the paper is to study the dilation behavior of rocks at the laboratory scale employing numerical simulation. A modified grain-based model is used to simulate the macroscopic response of crystalline rocks by considering micro-fractures at the grain scale. Grains generated with the Voronoi tessellation are allowed to fail in tension or in shear using a strain-softening model. Damage is represented by either grain boundary fracture or grain failure, or the combination of the two. As stress increases, the process of damage, fracture initiation and coalescence in rocks can be captured.The grain-based model was calibrated using test data of the Lac du Bonnet granite and a parametric study was conducted. Numerical simulation results showed that the proposed modeling approach is able to capture most of the mechanical properties, fracture pattern, and dilation behavior in both unconfined and confined loading conditions. In an unconfined compression test, interactions of microscopic fractures may lead to macroscopic shear or axial splitting failure depending on the chosen micromechanical parameters. Numerical experimental results show that the dilation behavior of the model is strongly related to the failure mechanism of rocks. Tensile-failure-dominated failure mode generates large dilation due to the formation of new cracks that are sub-parallel to the loading direction. On the other hand, shear-failure-dominated failure mode produces small volume increase. One significant finding from this study is that in order to capture large dilation using grain-based UDEC models, intragranular grain failure should be considered."

Jan 1, 2015

The JKRBT (JK Rotary Breakage Tester) is a newly developed impact breakage testing device for rapid ore breakage characterisation, and has recently been commercialised after a three year comprehensive validation study, involving five major mining companies and six industrialised JKRBT units deployed worldwide. Comparisons of breakage mechanisms and characterisation data between the JKRBT and the Drop Weight Tester (DWT) indicate that, despite the differences in the breakage modes, the JKRBT can provide statistically similar A*b parameters, by using a data reduction procedure which takes into account the difference in the number of contact points, strain rate and potential for secondary breakage. Feedback from the validation sponsors has indicated higher productivity and better repeatability of the JKRBT compared with the DWT. This better precision, combined with the JKRBT?s wider particle size capability and wider specific energy range, provide a more powerful tool, ideally suited to rapid mapping of ore hardness in geometallurgical and comminution applications.

Jan 1, 2012

By J. Schick, V. Granger

Nowadays, all French former uranium mining sites are remediated and redeveloped. If needed, mining waters containing radium have to be treated before discharged into the environment. Classical radium treatment consists in a (Ba,Ra)SO4 salt precipitation and radium monitoring was carried out using a time-consuming analysis called emanometry. Three zeolite samples have been tested to remove 226Ra from mining water. In batch experiment, radium was totally (R=100%) and quickly removed after 2 minutes contact time. Continuous sorption experiments were carried out through a vertical column at lab scale. Chabazite is the most efficient zeolite with an 226Ra activity below 0.2 Bq/L until 60000 Bed Volume. Chabazite is always efficient although radium content in material reaches 150 Bq/g. 226Ra uptake was also tested at semi-industrial scale on a pilot plant. More than 3000 m3 were successfully treated with a radium content below 0.1 Bq/L. The environmental impact assessment of Ra-chabazite was characterized by using batch leaching tests made according to the NF EN 12457-2 standard as applied on all wastes. Ra-chabazite stability is excellent during this test: radium leaching is very low, less than 0.005%. A new 226Ra measurement method was developed by ICP-MS for a better analysis reactivity. This new method was carried out in a couple of minutes with a lower sample volume than emanometry. The validation was performed according to the French NF T90-210 standard for the calibration function definition, the limit of quantification, the accuracy and the interferences.

Jan 1, 2020

By Chandrakala Kari, Divyang Shah, Lakshmi Kanth Reddy, Kaushik Vakil, Sanjay Sarkar, Bhavin Desai

Gases rich in sulfur dioxide generated as a by-product of smelting and converting operations of copper concentrate contain selenium apart from zinc, lead, copper, cadmium, bismuth, antimony, and arsenic. The gaseous stream is heat exchanged in waste heat boiler, dust collected in electrostatic precipitator followed by cleaning in reverse jet scrubber to remove fumes, halogens and fine dust before passing to DCDA Monsanto catalytic converter to produce commercial grade sulfuric acid. The gas cleaning section of the acid plant uses water to scrub the smelting gases. During scrubbing, precipitated solids, known as sludge, settles at the bottom of the reverse jet scrubber containing 30 to 40 wt% copper and selenium up to 40 wt% selenium. In the existing process, the sludge collected during scrubber cleaning process is directly recycled to the smelter for copper recovery. However, the selenium is expected to again vaporize due to high oxidation potential during smelting and converting, causing accumulation of selenium in sludge. In present investigation, a roasting process has been developed to recover the selenium from acid plant sludge before charging it to smelter for copper recovery. Selenium is associated with copper in acid plant sludge as copper selenide, as determined by X-ray diffraction and electron microscopy. Thermodynamic and thermo-gravimetry study revealed that the copper selenide phase present in the sludge was amenable to oxidation at 600°C forming oxides of copper and selenium (Cu-Se-O). However, the dissociation of selenium from the copper oxide was made possible by sulfatation using sulfur dioxide between 450°C to 600°C, resulting into the formation of CuSO4(s) and SeO2(g). Lab scale experiments were carried out in vertical tubular furnace to determine the optimum roasting conditions with respect to roasting time, temperature and molar ratio of O2:SO2. Using these optimum conditions, selenium up to 90 wt. % in the form of SeO2 vapors could be recovered from the acid plant sludge in a large scale commercial roaster. Roasted sludge free from selenium and containing oxides and sulfates of copper could now be recycled in the smelter for copper recovery. INTRODUCTION There is an increasing demand for minor metals due to their use in innovative technologies. Similarly, the increase in demand for selenium is expected due to disruption in sectors related to renewable energy and photovoltaic battery. Selenium is a chalcogen and a non-metal with black or red crystalline appearance. Selenium is used in the glass industry to decolorize glass and to make red-colored glasses and enamels. It is also used in solar cells and as a photographic toner. Selenium is used as a brasses in stainless steel to improve its machinability. Selenium sulfide is used in anti-dandruff shampoos. In spite of the toxicity of its compounds, selenium is also an essential trace element for humans and animals. Selenium occasionally occurs free in nature, but more often occurs as selenides of iron, lead, silver and copper. There is an urgent need for the development of new methods for selenium recovery from the existing resources. Commercially, selenium is obtained only from anode mud produced during electrolytic refinery of copper.

Jan 1, 2019

By Riggin P. R.

"IntroductionIndustrial Relations combines two very important relationships - employee relations and union relations.Employee relations always come into play when people are hired to perform tasks. Because mineral processing plants cannot be operated successfully without people, at least not yet, if they ever will be, employee relations must exist in an operatingplant.If the employees choose to be represented by a union, then a relationship with the union as an institution also comes into play. It is very important to note that unionization does not mean that the employee relationship is replaced by a relationship with the union. The latter is superimposed on the former, but it does not replace it. Similarities and overlaps in the two relationships will be present, some of which are of fundamental importance. Nevertheless, they are two different relationships and the reader should bear this in mind when reviewing those parts of this chapter which discuss unionization, collective bargaining, collective agreements, and work stoppages.These two important relationships, which we have chosen to combine and call industrial relations, have crucial roles to play in the social system which interrelates people performing the necessary tasks involved in the operation and maintenance of a plant. The technological organization - equipment, process layout and so forth - and this social system are interdependent and complementary. This chapter attempts to show that the potential level of effectiveness of both the technological organization and the social system depends on the recognition and nurturing of this nexus between them.Occupational health and safety and training are subjects for another chapter. But, both of these have been critical and longstanding employee relations topics . They are destined to take on added importance in the future. As issues in collective bargaining, they are also attracting increasing attention in all union relations. It is hoped that the reader will not isolate from industrial relations those topics which are being dealt with in another chapter. They are very much a part of it and we cannot refrain from making some reference to them."

Jan 1, 1989

By Yann Sivry, S. Subramanian, Divyasree C. Prabhakaran, Jean Riotte

The potential of a bacterial strain isolated from water samples collected from a chromite mine in Odisha, India has been assessed for the bioremediation of hexavalent chromium, a toxic environmental pollutant. The isolate was identified as Sphingopyxis sp., a Gram negative bacterium, adopting molecular biological protocols and biochemical characterization techniques. Detailed investigations on the bioremoval of Cr(VI) were carried out using Sphingopyxis sp. cells and the various parameters affecting the biosorption process were evaluated. About 55 % biosorption of Cr(VI) was obtained using Sphingopyxis sp. bacterial cells and the residual chromium in solution was found to be bio-reduced to the trivalent form, namely Cr(III). Thus, complete bioremediation of Cr(VI) could be achieved using the mine isolate, with contributions from both biosorption and bioreduction mechanisms. The Cr(VI) biosorption isotherm obtained for the isolate was found to follow a typical Langmuirian behavior and the free energy value of biosorption was determined to be ~-25 kJ/mol, indicative of involvement of chemical binding forces in the bioremediation process. The chromium biosorption kinetics by the isolate followed a pseudo second order reaction. The FTIR spectral studies revealed that carboxyl, hydroxyl, amino and phosphate groups were involved in the biosorption process. X-ray photoelectron spectroscopic studies on the bacterial cells interacted with Cr(VI) confirmed the presence of both Cr(VI) and Cr(III) on the cell surface. The electrokinetic studies revealed that the surface potential of the bacterial cells were less electronegative subsequent to interaction with Cr(VI), compared to the cells alone, which further testified to the binding of positively charged Cr(III) ions, formed by bioreduction of Cr(VI), to the bacterial cell surface. A marginal shift in the iso-electric point obtained for the bacterial cells interacted with Cr(VI), corroborated the involvement of chemical binding forces in the bioremediation process.

Jan 1, 2016

By U. Caliskan, S. Miskovic

Gravity separation is a technique that depends on the difference in density of minerals for their separation. Although this method is one of the oldest separation techniques, it is still preferred in the industry because of its low capital and operating cost while it is environmental-friendly. In this paper, we present a new numerical methodology that can be used to investigate dynamics of dense slurry flows in gravity separation systems. A simple channel with a set of riffles is selected as a test platform in order to observe the effect of the riffle shape on segregation profile of particles with different densities. It is believed that the riffle shape would affect the slurry flow and possibly cause one class of particles to segregate within the riffle zone. The turbulence, as a disturbance effect within the riffle zone, causes heavy particles to displace the light, that is, the heavy particles will be trapped in riffles, while the lighter particles are carried by water to the end of the channel, which is an example to uninterrupted suspension. MP-PIC model in OpenFOAM is used to study the effect of riffle shape and slurry percentage of solids in this simple gravity separator on particle segregation profile of four discrete mineral density classes, which are Quartz/Clay (SG 2.6), Pyrite (SG 4.2), Chalcopyrite (SG 5.1), and Gold (SG 19.32). Gold particles are found to be readily captured and retained in the riffles because of their high density, while particles with the intermediate densities are more influenced by the flow. The developed model framework has been proven robust and capable of providing physical results even for the flows with a very high percentage of solids, characteristic for mineral processing operations. INTRODUCTION Gravity-based ore concentration techniques make use of differences in density of minerals within an ore to enable separation of valuables from the gangue. As some of the oldest techniques used for ore beneficiation, they are known to offer a range of benefits such as low specific energy consumption and low capital and operating costs (Burt, 1999; Falconer, 2003; Holland-Batt, 1998), however, they suffer from low selectivity, poor separation efficiency, and low capacity. Gravity separation techniques are common practices in the mining industry and are employed widely for the precious mineral concentration, iron ore recovery and coal preparation (Kroll-Rabotin, Bourgeois, & Climent, 2013; Laplante & Spiller, 2002; Williams, 1997). For example, gravity separation systems are highly applicable for precious metal enrichment operations by being included in primary grinding circuits, shaking table tailing separation, pre-concentration of leach feed and flotation concentrate enrichment for both flash and conventional flotation purposes (Burt, 1999; Falconer, 2003; Holland-Batt, 1998; Laplante & Spiller, 2002; McAlister, 1992). Gravity separation can be employed in the copper processing circuits by being integrated into the pre-flotation circuit to capture the gravity recoverable gold (GRG) and any free copper aiming to enhance the gold and copper recovery of the plant. When native copper and GRGs are present in the deposit, this integration not only facilitates plant overall performance via removal of the valuables early in the circuit, but it also reduces downstream operational expenditures due to less retention time of coarser copper particles in the system.

Jan 1, 2019

By W. A. Lang

"IntroductionCARBONIZATION, gasification, and chemical utilization of coal are interrelated topics, which makes it difficult to review one without indicating its connection with the others. Hence, in Progress in Coal Technology, Series No. 5: Carbonization, reference was made to gaseous products recovered in the carbonization of coal, and .to a number of chemicals made from the tars, light oils, and ammoniacal liquors which are by-products of coal carbonization.In this, the sixth paper in the review series, prime consideration will be given to the complete gasification of coal to give a fuel for domestic industrial, or power purposes and a synthesis gas suitable for the manufacture of gasoline, Diesel oil, and chemicals. The hydrogenation of coal, an alternative source of liquid fuels and of chemicals, will be reviewed, as will be a number of processes for •the recovery of chemical products from coal by extraction and chemical treatment."

Jan 1, 1952

By David Davidson

Overview- Points To Be Addressed ? Review the building blocks of a successful and vibrant industrial economy ? China?s current position in the global economy ? China?s voracious appetite for raw materials ? Distortion in import/export trends ? Areas of strategic importance for China - Steel and its components - Agriculture self sufficiency - Energy now and for the future ? Do current valuation techniques fairly value ?strategic? assets? China ? The Economical Miracle - Massive shift in population from rural to urban - ?Middle class? growing rapidly, hence strong consumer growth - China is the manufacturing center for the world ? cheap labour and - modern facilities - Infrastructure build out ?US$585b stimulus package and 5 year plan - Rail ? 30,000 kms of new track planned by 2020 - Power ? 50% capacity increase, including 35 nuclear reactors - 100 major new airports - State of the art process and manufacturing facilities - Port capacity ? 100m TEU capacity increase by 2020 Class 1 national highway ? 35,000 km?s by 2020

May 1, 2010

By Jan W. Merks

The objective of metrology in mineral exploration is to derive unbiased confidence limits for masses of metals contained in reserves and resources. Sets of test results for gold and silver determined in pairs of interleaved bulk samples give unbiased confidence limits for the central value of each metal. The same sets of test results show how to verify spatial dependence by applying Fisher?s F-test to the variance of a set and the first variance term of the ordered set. A significant degree of spatial dependence gives a higher degree of precision for the central values of gold and silver. Plotting variance terms of an ordered set against the variance of the set and its lower limits of asymmetric 99% and 95% confidence ranges gives a sampling variogram. Sampling variograms put in plain view where spatial dependence in sampling units or sample spaces dissipates into randomness. The application of statistical methods to test results for sets of ordered core samples within boreholes, and for sets of ordered ore volumes within profiles, plays an important role in defining reserves and resources.

Oct 1, 2009

By E. L. Chanturiya

The research and characterisation for compositional, physicochemical, structural, electrical and flotation properties of various pyrite samples for a copper-zinc sulfide ore was carried out. Various methods were used during the research, such as optical microscopy, X-ray diffraction, electron probe micro-analysis (EPMA), phase emission analysis, routine chemical analysis, auger electron spectroscopy (AES), scanning electron microscopy (SEM), back-scattered electron images (BSE), potentiometry, and instrumental neutron-activation analysis, flotation. Analysis of obtained results established the interrelation between impurity structures and concentration of electric charge carriers in minerals, Butyl xanthate sorption and flotation yield of pyrite. The research concluded that pyrite samples differ by morphology, micro defects of structure, concentration of donor and acceptor impurities (Co, As, Sb, etc.) and conductivity parameters (thermo-electrical force, specific resistance and concentration of charge carriers The peculiarity of pentagon-dodecahedral pyrite is the high concentration of electric charge carriers (electrons) and the more negative surface potential (by 25–75 mV) in comparison to cubic pyrite. The surface of cubic varieties is more active, therefore it is oxidized in alkaline lime medium much faster, than the surface of pentagon-dodecahedral varieties. This phenomenon is caused by high reaction ability, irregular jointing and defects of cubic pyrite. This promotes the increase of calcium ion sorption on its surface and the decrease of Butyl xanthate sorption. According to this, an increase in alkalinity (lime medium) from a pH of 10.0–11.5 leads to an increase of gold content reporting to the tail of bulk flotation. Gold content is increased from 0.58 g/t (?? 9.5) to 1.9 g/t (?? 11.6), which represents an increase in gold recovery of 24.68 to 79%, respectively.

Jan 1, 2016

By Robert B. Parsons

"A t last the legal red tape which has tied up flow-through share financing has been cut. New rules effective for deals signed after 1986 simplify flow-through financing by removing the necessity f or cumbersome agency relationships. But there is no free lunch-the new rules require increased government reporting. And beware federal tax reform promises to have a good look at the new flow-through share rules. IntroductionFlow-through shares have always worked better in theory then reality as an effective financing tool. The concept is straightforward: a transfer of risks, tax deductions, and potential returns. But the mechanics of the old flow-through rules made the transfer of risk impractical to impossible by placing the responsibility for incurring Canadian exploration expense (CEE) on investors. The new rules are significantly more realistic, shifting that responsibility to the issuing corporation. However, every silver lining must have a few clouds around it. In the case of the new flow-through rules, the more obvious negatives are increased reporting requirements and reductions in CEE eligible for flow-through by amounts of assistance received. The new rules are effective for deals signed after 1986, however, so a few old-style deals are still around. Practical Difficulties with Old RulesThe old rules which applied to investments in flow-through shares were structured so as to make it the responsibility of the investor, rather than the issuing corporation, to perform the Canadian exploration expense for flow-through. Since most investors had neither the expertise nor the inclination to incur the CEE, this requirement necessitated the use of cumbersome arrangements whereby the investors would appoint an agent (usually the issuing corporation) to incur CEE on their behalf. Although the issuing corporation might consequently be the party which actually spends the flow-through share funds on CEE, the awkward legal structure of such an arrangement made the investor the ""principal"" incurring the CEE. As such, the requirements of the old rules were met and the investors could receive their flow-through share s."

Jan 1, 1987

By M. Rafati

In this investigation, the effects of T4 and T6 heat treatments of AZ91 magnesium cast alloy have been studied. The effects of different microstructural details such as morphology, size and distribution of precipitates and their influence on fracture mechanisms were investigated by optical and scanning electron microscopy. The mechanical strength of the alloy after T6 treatment was found to increase in comparison to the T4 treatment, due to the formation of discontinuous precipitates in the grain boundaries. Precipitation in this alloy occurs in two ways: continuous precipitation, which nucleates and grows inside the grains, and discontinuous precipitation, which forms at the grain boundaries. During ageing, the length of the continuous precipitates increases, and, hence, interprecipitate distance decreases. The formation of discontinuous precipitates causes initiation and propagation of cracks at and the weakening of the grain boundaries. This is the principal reason for the reduction of the ultimate tensile strength in T6 heat treatment in comparison to the T4 condition.

Jan 1, 2006

By J. Lu, J. B. Wiskel, D. G. Ivey, E. Niemi, H. Henein

Simulated TMCP using a Gleeble was undertaken to evaluate the effect of the austenite to ferrite cooling rate, coiling temperatures of either 400°C or 500°C and the magnitude of plastic deformation at the coiling temperature on the hardness of a Grade 483 (X70) steel. For comparable apparent cooling rates and deformation conditions, the hardness of the samples were independent of coiling temperature The application of a minimum compressive deformation > 8% was required to increase hardness at both simulated coiling temperatures of 400°C and 500°C. An increase in hardness was also observed with increased cooling times between 800°C and 500°C (i.e., slower cooling rates).

Jan 1, 2005

By George J. Cymerman

Since 1978, Syncrude Canada Ltd. has been expanding steadily its oil sand mining and processing capacity while reducing unit energy requirements. At the current rate of ~180 M tonne/year oil sand, the originally adopted Karl Clark?s 80°C version of the Hot Water process would require some 53 PJ (53 x 1015 Joule) heat. If this amount of heat were to be derived from burning natural gas it would cost $369 M/y (at $7/GJ). Fortunately, effective recovery of waste heat from the upgrading operations at the Mildred Lake site obviated the need for water heating with natural gas. The oil sand hydrotransport technology, first utilized commercially in the mid-nineties at Syncrude?s North Mine, reduced slurry temperature from ~80°C to ~50°C, cutting the unit heat requirement from 293 MJ/tonne to 183 MJ/t. However, in the new 100 Mt/year Aurora Mine even a 50°C process temperature would still require 18 PJ of heat energy per year. Only limited quantity of 65°C water could be imported from Mildred Lake site and some waste heat would be available from Gas Turbine Generators. A new, Low Energy Extraction (LEE) process was developed to minimize heat requirements by further reducing process temperatures to 25°C in the slurry pipeline and 35°C in the Primary Separation Vessels (PSV). Unfortunately, when applied to certain ore facies in Aurora, the LEE process yielded disappointing bitumen recoveries, necessitating an increase in slurry temperatures from 25°C to 35°C in the pipeline and from 35°C to 42°C in Primary Separation. In 2004, an Optimized Low Energy process (OLE) was developed and piloted at Syncrude Research using a 2000 kg/hour pilot plant. In the OLE process, most available heat is applied up-front to produce 45°C pipeline slurry at a density of 1.58 kg/l. Once the pipeline conditioning process is completed, the slurry is flooded with cold (10°C) water, resulting in PSV temperature of 34°C. The overall heat and water requirements are the same, or slightly lower, compared to those of the LEE process ? but without the penalty in bitumen recovery. Processing 100 Mt oil sand at 34°C (96 MJ/t), rather than at 50°C (183 MJ/t), will save $61 M/y (@ $7/GJ) and reduce green house gas emissions by ~47 %. The OLE process is currently being implemented at the Syncrude Aurora Mine.

May 1, 2006

By B. R. McEwen, A. N. Samis, J. H. Gray

"The Quebrada Blanca Copper Mine is an open pit copper project located at 4200 m elevation in the Chilean Andes. The deposit is a world-class supergene enriched porphyry with a mining reserve of 89 Mt of 1.3% copper. The supergene zone will produce 6.3 Mt of ore per year for more than 15 years to produce 75 000 t of cathode copper per year.This paper will review the project geology the computer model ling of the deposit, the mine planning process and the property production scheduling. With copper production .fixed by the onsite electrowinning capacity, the planning and scheduling aspects to optimize the project NPV will be discussed. Some of the logistics, equipment. personnel and process difficulties of operating a mine at 42()() m elevation will also be described. IntroductionProject DescriptionThe Quebrada Blanca Copper Mine is an open pit copper project located in the northern part of the Chilean Andes. The project is based on the supergene enriched portion of a porphyry deposit which has a mining reserve of 89 million tonnes at 1.3070 copper. Below the enrichment blanket, the protore represents a further resource.All ore will be leached, the higher grade material will be crushed and stacked for thin layer heap leaching, and the lower grade and oxide material will be dump leached as run-of-mine material. Solvent extraction and electrowinning will be used to produce 75 000 tonnes of cathode copper per year. Power will be supplied by a 40 MW on-site diesel generating plant with the waste heat being used for process heating. The leaching operation will operate in excess of 15 years and may be followed by open pit mining and conventional ore concentration of the underlying primary sulphide mineralization.Because of the dry location water will be piped 37 km from a ground water source at the Salar de Michincha. Water requirements will be approximately 1.5 million m3/year. The operation will eventually employ approximately 550 people on a 7-day-on, 7-day-off rotation with two twelve-hour shifts per day with an on-site camp. Busing will be provided to the port city of Iquique."

Jan 1, 1994

By Ian E. Efford

The paper gives an assessment of Canada's energy supply-and-demand position, the current situation and projections into the future, as well as a review of some alternative energy futures for Canada. The main elements of Canada's energy strategy for the period 1977-1990, with particular reference to the role of energy conservation, are discussed, leading in to the development of the national energy conservation program.

Jan 1, 1977