Search Documents

The words ""Uncertainty"" and ""Risk"" pervade every discussion about mining exploration and investment. Perhaps these terms are subjectively understood by industry professionals, but objective portrayal of these concepts outside the industry is a woefully undeveloped science. This paper addresses current industry understanding and practice regarding quantitative risk assessment techniques, and provides examples of the application of three of these techniques. Probabilistic techniques for financial risk assessment are valuable adjuncts to conventional financial analysis, and address a range of issues not assessable by any other means. The value of whole-of-project probabilistic risk assessment is currently debatable for decision-making purposes, but is seen as important as a mechanism to focus attention to the critical issues that ultimately impact on project success. The dissection of project capital into risk and non-risk components provides valuable insights into risk characteristics not readily quantifiable in any other way. This technique also provides a framework for more objective ""what if?"" scenario evaluation and for the capital structure of resource projects. Finally, mechanisms for the valuation of undeveloped reserves are examined, and guidelines suggested. The importance of reliability in production cost estimates is highlighted and the impact of early development on reserve valuations is discussed. The importance of economics throughout all stages of the evaluation process is fundamental.

Jan 1, 1994

Bacterial leaching of sulfide minerals are fairly well established in heap, dump and in situ leaching and the primary bacterial treatment of refractory gold concentrate using CSTR have gained industrial prominence in recent years. Three cultures, a mesophile T ferrooxidans (DSM583), a moderate thermophile Sulfobacillus acidophilus (strain YTF1) and a extreme thermophile (Sulfolobus strain BC65) were used for the biooxidation (pre-treatment) of the Porgera gold-bearing pyrite concentrate under optimum O2 and CO2 enriched air (30 per cent O2 and ten per cent CO2) based on volume ratios. The positive effect of using oxygen and carbon dioxide enriched air for the biooxidation of gold-bearing pyrite mineral was clearly demonstrated where an increase in Fe release rate by a factor of 2.8, 1.8 and 1.5 for DSM583, YTF1 and Sulfolobus respectively were observed compared with the shake flask tests. The lag phase observed with the other test conditions such as in shake flask or with air decreased by about 80 per cent for all three cultures. The average observed dissolved oxygen concentrations in the pulp for these tests were 8.7, 5.8 and 5.0 mg/L for DSM583, YTF1 and Sulfolobus respectively, indicating that O2 was not limiting in these tests. The pulp redox potential was observed to increase with time for all tests coincident with the leaching rate and reaching a maximum of 663 mV, however the maximum value differs for each strain, with DSM583 exhibiting the highest followed by YTF1 and Sulfolobus. Biooxidation of pyrite under optimum gas enrichment at different pulp densities showed near total Iron extraction occurred for pulp densities of three, ten and 20 per cent (w/v). At high pulp densities, more so at 40 per cent than 30 per cent (w/v), the leaching rate decreased rapidly for tests with YTF1 and Sulfolobus. Monitoring of dissolved O2 shows that O2 demand increased with increasing pulp density and the average dissolved O2 concentration observed for YTF1 and Sulfolobus at 40 per cent solids concentration was 1.0 mg/L and below, suggesting limiting oxygen and carbon dioxide conditions for these two cultures. The decrease in leaching rate observed at high pulp densities (30 and 40 per cent) under optimum gas enrichment was accompanied by low metal dissolution and low redox potential values which was attributed to shear stress due to attrition of cells by high solids concentration, toxicity of metal ions especially Ag and Fe and the formation of precipitates and jarosites as confirmed from XRD analysis of leach residues hence impeding the leaching process. Limiting conditions due to high pulp density and viscosity were only observed for YTF1 and Sulfolobus. The subsequent cyanide leaching for precious metals from the pre-treated pyrite concentrate in all cases shows the extent of gold and silver recovery increased with the degree of pyrite oxidation and Au and Ag recoveries in excess of 80 per cent were achieved compared with only 18.1 per cent and 35.9 per cent for gold and silver respectively when treated by direct cyanide leaching on the original, untreated concentrate.

Jan 1, 2004

By C Beal

Proper understanding and management of production drilling in sublevel cave (SLC) mines is essential for meeting production targets and for avoiding inefficiencies that could lead to costly bottlenecks. In many SLC mine management models drilling is considered a derivative activity of firing and bogging. Its scheduling is considered to be implied in a firing schedule and given an arbitrary target completion, ‘several weeks’ or ‘a month’, ahead of production firing. Like development, drilling activities are most efficient when conducted separately from other production activities. Unlike development, however, it is not apparent during planning and feasibility how far in advance of firing drilling activities ought to be conducted. This paper presents a method of defining a minimum threshold of drilled stocks above which drilling, firing and bogging operations occur most efficiently. As an example, the drilling activities, procedures, and maintenance at Glencore Xstrata’s Ernest Henry Mine are presented, and the larger scale consequences of improvements to these areas are presented to illustrate their importance in the operation of an SLC mine.CITATION:Beal, C, 2014. Understanding the role of production drilling and drilled stocks in efficient operation of a sublevel cave mine, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 235–242 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By N N. Viswanathan, D Kumar, S Kumar

In secondary steelmaking, calcium treatment is practised to modify the solid alumina or spinel inclusions into liquid or partially liquid calcium aluminates. It has been seen that the dissolved calcium reacts with sulfur or oxygen present in the steel to form CaS or CaO type of transient inclusions. Post-calcium treatment these transient inclusions further react with pre-existing alumina or spinel inclusions and modify them. In addition, direct modification of pre-existing inclusions is also reported in the literature. In the present study, laboratory-scale induction furnace-based experiments are carried out to melt electrolytic iron in an alumina crucible followed by deoxidation with aluminium. The CaS-based composite material, prepared in-house, is added after the aluminium deoxidation to study the stability of CaS at the steelmaking temperature. Multiple steel samples were also taken to track the dissociation of CaS by means of sulfur pick-up in steel. Additionally, inclusion analysis of these steel samples was also performed to track changes in the chemical composition of inclusions in response to CaS addition. It has been seen that the CaS dissociates leading to a gradual pick-up of sulfur in steel. The scanning electron microscope – energy dispersive X-ray spectroscopy (SEM-EDS) analysis reveals that the alumina crucible and floated alumina inclusions are modified into calcium aluminates and the extent of modification depends on the contact time of CaS with the two sources of alumina mentioned earlier. However, the modification of alumina inclusions in the bulk steel did not occur during these experiments.

Jun 19, 2024

By N B. McCaffrey, V Glenn, C Johns, P D. Erskine, A T. Fletcher

"Underground coal mining is the dominant method of extracting thermal and coking coal in the southern and western coalfields of New South Wales. Monitoring mining-related subsidence forms an important component of environmental impact assessments and subsidence management plans, particularly when there are conflicts between the interests and requirements of mining and environment and community groups. However, there are few specific guidelines for monitoring the impacts of subsidence on terrestrial and aquatic ecosystems, leading to inconsistent policy approaches and highly variable abilities of monitoring programs to accurately detect biological change.This paper highlights the use of a conceptual framework to guide the development of a long-term ecological monitoring program at an underground coalmine in the Western Blue Mountains, New South Wales. Two pilot studies are described: determining the level of observer agreement to assess the condition of a vulnerable tree species (Capertee Stringybark) comparing field sampling methods for detecting a rare heath shrub, Epacris muelleri, using a power analysis to determine sampling intensity requirements.These examples demonstrate that investment in initial pilot studies to test different monitoring approaches can have long-term benefits for stakeholders by more confidently being able to detect potential impacts.CITATION:McCaffrey, N?B,?Glenn, V, Erskine, P?D, Johns,?C?and Fletcher, A?T, 2014. Detecting long-term ecological impacts of subsidence from underground coal mining – a tale of two pilot tests, in Proceedings Life-of-Mine 2014, pp 139–152 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 16, 2014

By K L. Avarmaa, M A. Rhamdhani, A D. P Putera, H T. B M Petrus, G A. Brooks

Multistage slag treatment was carried out to investigate boron removal from metallurgical grade silicon. Boron is known to be one of the most difficult elements to remove from silicon. Depending on boron initial concentration, boron can be removed from silicon into certain level; most previous studies have attained final 50–100 ppmw (parts per million weight) boron in the silicon using slag treatment. The term ‘multistage’ refers to a process where the resulting silicon from the initial slag treatment is further refined multiple times using a new slag. In this study, an initial slag composition of 45CaO-45SiO2-10Al2O3 (wt per cent) was utilised. Using this technique, boron level in the silicon was expected to be gradually lowered because the new slag will always have more capacity to reach the equilibrium distribution coefficient (LB = (ppmwB)slag/(ppmwB)Si). The current study was carried out through combined thermodynamic calculations (using FactSage™ ver 8.2, by Thermfact Ltd, thermochemical package) and high-temperature experimentation. The thermodynamic calculations were carried out for reactions at 1500, 1550, and 1600°C for three different scenarios: 1. Single stage refining with varied slag to Si ratio. 2. Multistage refining with slag to Si ratio of 1:1. 3. Multistage refining with slag to Si ratio of 2:1. The multistage experimental work was carried out at 1550°C under inert gas atmosphere each time for 2 hrs, with slag to Si ratio of 2:1. The simulation results indicate that the boron distribution coefficient stay essentially constant with varying slag to Si ratio and temperature, around 1.8 to 2, and the experimental results measured LB in the same range, between 1.5 and 2.5. By harnessing this feature, the simulation showed that boron can be removed by approximately 78 per cent in each stage. The experimental result confirmed that the boron concentration in the silicon was reduced by a total of 97.8 per cent from its initial value using four stages of slag treatment, from initial 270 ppmw down to 6 ppmw.

Aug 21, 2024

By A Hughes, S G. Rosin

This paper presents the design and construction approach adopted for the widening and stabilisation of the existing decline tunnel forming part of the Scenic Railway Upgrade project at Katoomba in the Blue Mountains of New South Wales (NSW), Australia. The overall upgrade project included new trains and track, rebuilding of the top and bottom station and installation of a new winch and control system. All the works were undertaken over an eight-month period between August 2012 and April 2013 as part of a $30 M upgrade of the railway.The railway is the steepest cable-driven line in the world at a maximum of 52° extending over 350 m and descending from the escarpment into the Jamison Valley. The track was built in the 1880s for coal haulage and is recognised as a remarkable engineering achievement for its time. The tunnel section extends for about 120 m at the start of the decline and is about 3.5 m wide and 3.5 m high. The tunnel was excavated principally within medium to high strength Banks Wall sandstone and given that the widening only involved about 200 mm of trimming of the crown and sidewall this aspect of the work was not a critical support issue, except at the upslope portal. The tunnel crown however is entirely intersected by a major near vertical shear zone which presented significant challenges for the tunnel stabilisation works.Three-dimensional laser survey scanning was used for definition of the tunnel clearance envelope for the widening, and also to subdivide the tunnel into various geotechnical sections to assist in support design. Specifically oriented rock bolts extending beyond the shear zone into stable rock were used together with mesh, shotcrete and extensive strip drains and flushing points for drainage of the shear zone.Unique aspects of this project were included into the specifications and work methods. This included construction of a mobile working platform for tunnel works, the use of dry shotcrete application, difficult access for rock bolting and limiting vibration during the tunnel trimming works due to the risks associated with crown instability. The works also took into consideration particular safety constraints/work exclusion areas to address the risk of detachment of rock which could mobilise downslope to the track area below. This was required because other works were in progress such as micro-piling and bottom platform works which were being undertaken concurrently with the tunnel work.CITATION:Rosin, S G and Hughes, A, 2014. Scenic Railway Tunnel upgrade in the Blue Mountains, New South Wales – an approach to design and construction, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 607–618 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By Baafi EY, Appiah HK

The Prestea Goldfields Ltd of Ghana, West Africa has produced over 170 t of gold with average grade of 11 g/t since 1912. The deposits occur in a wide shear zone which closely follow the Birimian-Tarkwaian contact. Both the Birimian and Tarkwaian systems are of Precambrian age. Underground exploration is carried out to delineate ore bodies by means of AX size diamond drilling at 50 m sampling intervals. After the orebody has been delineated, development work is carried out by exposing the gold reef. Channel sampling is then carried out at about 3 m intervals in both the stope and stope drives. A channel sample length is commonly 0.6 in, but may vary depending on physical characteristics of the reef. The values of channel samples are linearly combined to obtain the average reef or slope values and/or widths of the exposed sections. The sampling practice and methods of improving the efficacy of sampling at the mine are described.

Jan 1, 1976

On Monday, October 25th, 1971 at approximately 12.15 a.m. the night shift proceeding underground discovered smoke at No.1 and No-3 cut throughs on the eastern side of the belt heading and in close proximity to the upcast shaft. Attempts to control the fire continued throughout the morning; as the position underground altered various procedures were adopted in an effort to contain and control the fire. Despite these efforts at approx. 12.40 p.m. a sudden change occurred which made it necessary to withdraw all workmen from underground, the vicinity of the Tunnel entrances and upcast shaft. Sealing of the mine at the entrances was the only remaining alternative. Several boreholes were put down to enable sampling of the atmosphere and air temperatures to be taken. This was essential as a guide to determining when conditions were suitable to allow exploration of the area using mine rescue self contained breathing apparatus.

Jan 1, 1972

By Rao S. B, Baafi E. Y

A venturi based multi-scrubber air cleaning system has been developed for dust control along a longwall face in coal mines. The system consists of a number of scrubbers. strategically placed along the wall face which deliver cleaned air at high exhaust velocity into the middle section of the longwall cross-section thus dividing it into two zones. The aim is to maintain the walkway on the powered support side as a zone of relatively clean air. Laboratory studies have shown that the scrubber's average efficiency is 90 per cent. Field trials in three longwall faces have shown that. under normal operating conditions. 40 to 50 per cent average protection efficiency can be achieved within 3 m to 4 m downstream of the scrubber. A three-dimensional finite element computational fluid dynamic model. FIDAP. was used to simulate the airflow patterns the dust concentration and the scrubber dust control technique at a typical longwall face. Results of simulations tally very well with the field results.

Jan 1, 1995

Lateritic nickel ore occurs as a supergene or residual deposit as a result of the tropical weathering of underlying ultramafic rocks. The mineralisation may be as hydrated Ni-Mg silicates, like garnierite (silicate ore); or as hydrated Ni-Fe oxide (oxide) ore. Non-sulphide ore represents only 30% of the tonnage mined, but represents 85% of the total world's nickel reserves. A typical lateritic profile consists of 4 zones above the unweathered ultramafic parent rock: Zone 1: the "upper laterite" which is dark red-brown, porous and concentrically structured. It contains 0.2 to 0.8% Ni, 48.0 to 72.0% Fe, and 0 to 9.5% MgO. It is often capped by a ferricrete crust. Zone 2: the "middle laterite", which is red-brown to light brown and more porous than the above zone. It contains 0.8 to 1.5% Ni, 42.0 to 48.0% Fe and 0.5 to 6.0% MgO. Zone 3: the "basal laterite" which is yellow-brown to yellow-orange,

Jan 1, 1974

Western Mining Corporation, managing partner of the Windarra Nickel Project are in- stalling a raise-bored haulage shaft and under- ground crushing system at the Mt. Windarra Nickel Mine. The system will be the second of its type installed by W.M.C., the first being in- stalled at the Otter-Juan mine in Kambalda in 1976/77. Both haulage systems became necessary as a result of the increasing production limi- tations, and escalating costs of a deep decline mine. The Windarra haulage system required a single 3m diameter vertical raise drill hole to a depth of 470 metres. Two five tonne skips in balance will hoist crushed ore and mullock to the surface, at a design rate of 200 tonnes per hour, effectively reducing truck haulage leads by up to 50%. It is expected the project will be in full operation by mid 1982 and will enable the mine to achieve an annual production rate of 600,000 t.p.a. by 1983.

Jan 1, 1982

By D J. Williams, S Islam

Worldwide production of black coal amounts to about 8 billion tonnes. Perhaps 20% of this annual production is washed to improve its quality, generating perhaps 250 million tonnes of coal tailings annually, generally in the form of a slurry. The coal tailings slurry is typically thickened to about 25% solids by mass prior to disposal to a tailings storage facility (TSF), and hence comprise mostly water (about 85% by volume), plus sand, silt and clay-sized mineral particles and carbonaceous material. While the tailings settle and consolidate on deposition in the storage facility, their high moisture content makes them prone to run-out should the tailings dam fail, and makes rehabilitation of the tailings difficult. Hence, it is important to understand the consolidation and shear strength of coal tailings. Laboratory consolidation testing of coal tailings from a slurry to a soil-like state has been carried out in a purpose-built, large-scale, slurry consolidometer, instrumented with load cells and pore water pressure (PWP) transducers. Laboratory vane shear testing of coal tailings produced at different gravimetric moisture contents has also been carried out. The test results have allowed a regression model to be developed relating the peak vane shear strength of the coal tailings to their gravimetric moisture content.CITATION:Islam, S and Williams, D J, 2018. Consolidation and shear strength of coal tailings slurries, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 62–71 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By O van Baalen

The Ernest Henry Mine is a copper-gold open pit operation situated in northwest Queensland, Australia. It is owned and operated by Xstrata Copper, with a current throughput of 11 Mtpa, however, open pit operations are scheduled to cease in mid 2011. The deposit dips approximately 45º and extends for at least another 400 m vertically below the final 530 m deep pit design.Construction and development of a sublevel caving (SLC) operation beneath the open pit was approved in December 2009. The feasibility design requires 39 km of development to be completed prior to production, which will commence in the fourth quarter of 2011. Initial ore production will be trucked and will increase to 3 Mtpa by the end of 2012, after which a hoisting shaft will be used. Ore production will then increase to 5 Mtpa in 2013 and ultimately to 6 Mtpa in 2016.Two 3000 kilo watt of refrigeration (kW(R)) modular refrigeration plants will be installed, as well as two 1600 kW mixed-flow fans capable of a combined flow rate of 780 m3/s at a total pressure loss across the mine of 2000 Pa. The main fans will be installed underground and will exhaust into the base of the pit.The following challenges were faced in the development of the ventilation and refrigeration network:•a relatively steep geothermal gradient,•tropical ambient conditions,•working under a wide pit shell, and•a large underground trucking fleet prior to shaft commissioning.A considerable number of ventilation studies were conducted with later studies extensively using Ventsim Visual™ mine ventilation software to complete the design process of the ventilation and refrigeration networks, including the comparison of several alternative designs. The paper focuses on design challenges prior to the commissioning of the hoisting shaft, and discusses resistance optimisation and occupational hygiene-related design parameters, such as heat and diesel emissions, production level ventilation, main fan selection and location, and refrigeration requirements.

Mar 21, 2011

The Pongkor Gold Mine employs 678 staff. The mine is owned by the Indonesian state company PT Antam Tbk and is located 100 kilometres south west of Jakarta, in Java, Indonesia. Mine and infrastructure development started in 1992 following intensive geological exploration over 15 years. First gold production was in June 1994. The mine comprises three main orebodies: Ciguha, which is nearly mined out, dips at 75¦ from surface to 150 m. Kubang Cicau, dipping at 80¦ from surface to 230 m, and averages 3.5 metres thick at a grade of 10 g/t Au and 128 g/t Ag; and Ciurug, dipping at 60¦ from surface to 300 m and averages eight metres thick at a grade of 14 g/t Au and 172 g/t Ag. Present global ore reserves are 4.6 million tons at a grade of 12.3 g/t Au and 133.6 g/t Ag. Exploration is continuing for new veins. Initial mining was by manual cut and hydraulic fill at Ciguha, followed by Kubang Cicau. In 1996, it was proposed to convert Ciurug to a mechanised cut and fill operation. Two single boom jumbos and three load-haul-dumps (LHDs) were purchased with the assistance of a gold loan from NM Rothschild and Sons. Implementation of this upgrade was delayed by both a national economic crisis and an invasion of the concession by illegal miners. It was not until May 1999 that raise bore vent rises and access drift infrastructure commenced. Major underground development started in 2000 and is continuing. Production cut and waste fill stoping started in July 2001. The change from manual to mechanised methods has required a total change in work practices and attitudes. However, the process has resulted in a production increase from 600 tpd to 1200 tpd. A three-month compliance test (a condition of the financing loan) was successfully completed, from July to September 2001, with an average production of 700 tpd at Ciurug and 500 tpd from Kubang Cicau.

Jan 1, 2002

By Nicol SK, Engel MD

Ion flotation involves the adsorption of ionic species, in association with surfactant molecules, at the surface of rising gas bubbles, for the purpose of recovering and concentrating those ions. The objective of this study was to optimise the ion flotation process using a heap-leach liquor, containing gold cyanide, and the surfactant cetyl trimethyl ammonium bromide (CTAB). The aim was to minimise the surfactant reagent dose, maximise the throughput of feed liquor in the process, and satisfy the dual constraints of a high gold recovery and a high volume reduction factor. Development of a first order model of the ion flotation process formed the theoretical basis for the test program procedure and the interpretation of the results. Batch tests were used in order to determine the ultimate recovery curve for the heap leach liquor-CTAB surfactant system. The results indicated that a surfactant dose of about 0.083 g/l would be necessary in order to achieve a satisfactory gold recovery. Continuous tests were then performed on a small-scale pilot plant at the Newcastle Laboratories. The optimum result achieved was a gold recovery of 85 per cent, a volume reduction factor of ten, and a feed throughput of 2.3 m3/m2-h. Recent work also indicates that very much higher volume reductions can be achieved using a larger diameter vessel. The improvement may be a consequence of a reduction in wall effects and hence an improvement in foam drainage.

Jan 1, 1993

By G E. Smith, G N. Lye

Wall control blasting practices are necessary to reduce the impact of blasting on mine faces but can also have a significant negative impact on mine productivity and operating costs. The conventional practice in deep open pit mines is to use so-called trim blasts adjacent to pit walls. To provide burden relief these trim blasts have fewer rows than full production blasts and are fired to a cleared free-face; hence they are termed æunchokedÆ. This practice leads to scheduling constraints on the pit operations and can cause ore dilution due to excessive muckpile movement. The use of such trim blasts stems from the perception that increased wall damage results from æchokedÆ blasts. These concerns are based on the unproven assumptions that blast vibration levels and explosive gas penetration increase with increased blast burden and face confinement. This paper describes work undertaken as part of a major investigation into wall control blasting at the KCGM Fimiston Mine, Kalgoorlie, Western Australia. It details a study to assess damage effects due to blast burden. Borehole air pressure measurements and borehole video camera inspections were done behind a series of single blastholes drilled with varying burden distances, as well as behind a dedicated trim blast and a full production blast. It was found that the measured damage effects, including visible rock cracking, dilation, and the limited extent of gas penetration behind the blastholes, did not vary significantly with burden or blast type for the cases tested. This result was in complete agreement with detailed vibration measurements conducted by Blair and Armstrong (2001) during the study, which found that vibration was independent of blast burden. As a result of these investigations, changes to the blasting practices at the mine were implemented. Dedicated trim blasts and free-face blasting have been replaced by modified production blasts and the practice of æchokingÆ blasts has been introduced. This has resulted in a significant improvement in productivity and cost savings without compromising pit wall integrity.

Jan 1, 2001

By Morinaga K

The optical basicity (A, Pb2+ as probe ion) of various oxide glass systems has been measured to establish the new basicity scale of slag melts. Best conditions of glassy fragments to measure A were as follow, (1) 1 ti 4 x 10-2 wt% Pb content, (2) 0.2 mm in thickness, (ii) enough annealing (about 10 hr) at a temperature 200¦C below Tg., and (4) polishing a surface well. the variation of A with composition was correlated to that of relative oxygen activity of slag melts. The estimation of basicity of slag melts from it could be valid. The A of opaque and coloured quenched slags could not be measured. An approximately linear relationship, however, exsisted between the isomer shifts (b) of Fe3+ ion in slag derived from the Mossbauer effect and A. Therefore, -4 of various metallurgical slag could be estimated from this relationship. These results can be expected to establish the new basicity scale of slag melts as the Louis basicity.

Jan 1, 1980

By A D. Strand

The Coeur dÆAlene mining district in northern Idaho, USA is the second largest producer of silver in the world. The Proterozoic Revett Formation hosts most of the mesothermal Ag-Pb-Zn vein ore in the district; it consists of informally designated lower, middle, and upper members. All three members show up to an order of magnitude of southward thickening across the regionally significant Osburn fault. Changes in thickness of the Revett Formation across the Osburn fault reflect a major, down-to-the-south, crustal-scale fault that:was active during sedimentation, was periodically reactivated during the structural and metallogenic history of the district, and likely provided first-order control over regional fluid flow during mineralization events. Where vein structures intersect favourable strata, they produce rich ore; where vein structures cross unfavourable strata, they are poorly mineralised or barren. The most favourable host rock in the district is quartzite, which accounts for the large production from the quartzite-rich Revett Formation.The district has five main types of hydrothermal alteration:feldspar destruction, hydrothermal bleaching, carbonatisation, sulfidation, and silicification. Feldspar destruction is the most extensive and pervasive type of alteration, involving the district-wide absence of feldspar from Belt Supergroup rocks. Hydrothermal bleaching results from the destruction of hematite; it forms alteration envelopes that extend for tens to hundreds of metres into the wall rocks around many of the mineralised veins. Siderite alteration is most diagnostic of mineralisation, forming alteration envelopes that extend for tens to hundreds of metres into the wall rocks around all mineralised veins. Fine-grained arsenopyrite and/or fine-grained pyrite commonly form alteration zones adjacent to high-grade ore shoots that extend for metres to tens of metres into the wall rocks. Widespread silicification is most easily recognised by the presence of numerous quartz veins.

Jan 1, 2002

A research and testing facility has been developed at Simtars to allow the spontaneous combustion testing of coal on a large scale. In this adiabatic reactor, the coal particle sizing is closer to that which could be found in the goaf and therefore the reaction is more likely to simulate the underground situation. This allows aspects of the spontaneous combustion process and methods for detecting a heating to be investigated which cannot be done in an operational mine. Up to 18 tonnes of run of mine or crushed coal is loaded into the reactor and allowed to self-heat while the temperature and gas profiles within the coal pile are monitored. The gases evolved from the coal are analysed using a fixed gas monitor system and gas chromatography to determine which of the common mine fire indicators and ratios can be used to predict the onset and progress of coal heatings. Benchmarking of the inherent propensity of a coal to spontaneously combust at both the large- and laboratory-scale is also possible by comparing the sample against previously tested samples. It has been found that the coal particle size affects both the time it takes for the coal to react and the location of the developing heating. The heatings generate approximately one metre from the inlet but in the crushed coal case do not progress to an advanced heating stage until the æhot spotÆ migrates towards the coal surface where there is an increased oxygen supply. Physical properties such as the compressive strength of the coal also affect the heating size and the time it takes for a heating to develop. Higher strength coals appear to oxidise more slowly and therefore take longer to self-heat as oxidation of the coal is the heat-generating step in the spontaneous combustion process. The best indicators of the state of the heating were found to be CO make and GrahamÆs ratio which are independent of air flow. Investigation of a potential spontaneous combustion should begin as soon as the CO make or GrahamÆs ratio exceed the background levels. The results from the tests undertaken on a number of Queensland and NSW coals are reported here together with the implications for the mining industry.

Jan 1, 2005