Search Documents

By M S. Henderson, R D. Alorro, L G. Dyer

An alternative leaching system for rare earth element recovery from monazite is under development. The initial stage utilises oxalic acid to convert the rare earth phosphate into an oxalate salt through dissolution and reprecipitation and it is the efficiency of this stage that governs the overall recovery achieved. It has previously been proposed that lixiviant consumption is the primary limitation in this process. This work further investigates a range of conditions in an attempt to further elucidate the factors influencing the achievable conversion in this stage. It has been shown that the pH may be governed by multiple reactions both consuming and producing acid (thus the mild change over time). The importance of proper mixing and potential to operate at lower temperature with only moderate impact on kinetics has also been demonstrated. Staged/sequential leaching is more effective in fresh solution as opposed to restoring the lixiviant concentration with subsequent reagent addition, suggesting some impact of solution composition. However, contrary to previous findings, subjecting the leach residue to fresh solution resulted in significant decline in leach rate and overall dissolution. This may be because a greater proportion of conversion was achieved in stage 1 in this work than in previous investigation. This may indicate that eventual passivation or the presence of some more refractory REE minerals limits dissolution. Iron dissolution was relatively consistent upon exposure to fresh solution, displaying the ability of the solution to continue to leach the goethite component of the concentrate.

Aug 24, 2022

By E Jak

A viscosity model has been developed for both completely liquid and heterogeneous, partly crystallised slags in the Al2O3-CaO-æFeOÆ-SiO2 system in equilibrium with metallic iron. The Urbain formalism has been modified to describe the viscosities of the liquid slag phase over the complete range of compositions and a wide range of temperatures. The Roscoe equation has been used to describe the effect of presence of solid suspension (slurry effect) on the viscosity. The parameters of the viscosity model were optimised to describe large experimental data set in the low-order subsystems, as well as in the multi-component system. The computer package FACT was used for prediction of the proportion of solids and the composition of the remaining liquid phase. The model provides a good description of the experimental data (over four thousand experimental points) in liquid phase, and liquid + solid mixtures, over the complete range of compositions and a wide range of temperatures. This model can now be used for viscosity predictions in industrial slag systems. An example of the application of the new model to slag cleaning and reduction smelting processes is given in this paper.

Jan 1, 2000

By D J. Williams, S Islam

Fine-grained coal tailings slurry undergoes only limited settling and self-weight consolidation, and tends to remain slurry-like and unsuitable for conventional laboratory consolidation testing. In addition, constant rate of loading consolidation testing is more representative of the continuous disposal of tailings slurry into a tailings storage facility (TSF) than conventional step loading. The laboratory consolidation testing of coal tailings slurry under a constant rate of loading has been carried out in a purpose-built, large-scale, slurry consolidometer, instrumented with load cells and pore water pressure (PWP) transducers. In the slurry consolidometer, the rate of loading may be varied to represent the actual rate of rise of the tailings in the TSF. A slow rate of loading increases the test duration, while too fast a rate of loading may build up very high excess PWP, without achieving significant consolidation. For the particular fine-grained coal tailings slurry tested, the rate of loading in the slurry consolidometer is varied to access its effect on the development and dissipation of excess PWP. The resulting consolidation parameters are evaluated and explained using the recorded settlement and PWP data.CITATION:Islam, S and Williams, D J, 2018. Optimisation of constant rate of loading slurry consolidometer testing of fine-grained coal tailings, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 72–80 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By Boontanjai C, Boyapati ER

Reagents used for batch flotation tests were Aeroxanthate-343 & 350, Dow Z-6, & reagent-4037 (from Benambra) as copper collectors; Na2SiO3 & Na2S2O3as gangue depressants; lime & HCl as pH regulators; and pine oil & MIBC (methyl isobutyl carbinol) as flotation frothers. A Denver Sub A flotation cell of capacity 250 gms was used for the batch flotation experiments. Atomic absorption spectrophotometer was used for copper assays and microscopy for selectivity and liberation studies. Melbourne tap water was used throughout the experiments. Unless otherwise stated, the following parameters apply to the flotation experiments: flotation impeller speed - 1300 rpm, pulp density during flotation- 22%, reagents addition - in 4 stages, total conditioning time for collectors - 8 minutes, total flotation time- 9 minutes. A variable quantity of copper mineral collector according to the test in question was added, then conditioned the pulp for 2 minutes. The froth was removed by hand, scraping the full length of the cell at constant depth every 10 seconds. No frother is required for this copper tailing flotation. Four concentrates were collected after addition of collector and conditioning at 2,4,6 and 9 minutes. The pulp volume was maintained at a constant level to yield a constant froth depth.

Jan 1, 1990

By L Smith, R Beckie

Controls on environmental loading from acid rock drainage (ARD) are not well understood in waste rock material. In particular, relationships between subsurface flow and the timing, duration, and intensity of leaching of metals and acidity from waste rock dumps remain ill defined. This study investigates field-scale relationships between subsurface flow processes and geochemical processes in unsaturated waste rock. A 12-metre tall, unsaturated waste rock pile, constructed in 1994, was deconstructed and sampled at Key Lake, Saskatchewan, Canada, during the summer of 2000. A detailed sampling methodology was developed to characterise physical and chemical properties of waste rock material within the waste rock pile. Physical properties were characterised by measuring soil-water suction, volumetric water content, and grain-size distribution at 60 random locations within the pile and grain-size distribution at 20 grid locations within the pile. Attempts to develop a field-based soil water characteristic curve from physical field-data failed due to spatial variability and hysteresis of waste rock properties. As a result, grain-size distribution was used as a relative measure of subsurface flow. Paste pH, pore-water geochemistry, mineralogy, and water-soluble extraction results were used to characterise geochemical processes and sulfide oxidation at each of the 20 grid locations. Geochemical characterisation results demonstrated the preferential weathering of marcasite relative to pyrite and chalcopyrite. Dolomite was the main buffering carbonate mineral. Gyspum, jarosite and iron oxyhydroxides were the main secondary minerals. Pore-waters contained up to 800, 11.7, and 6 mMolar (78 000, 690, 1400 mg/L, respectively) of sulfate, nickel, and uranium, respectively, suggesting significant weathering has occurred. Measures of weathering indicators show no discernable correlation with grain-size distribution nor do they show any spatial relationship within the sampled grid. Reasons for this may include limited duration of waste rock exposure to weathering and development of fluid flow-paths, and limitations of characterisation methods used. Indeed, six years may not be long enough for weathering patterns to develop due to fluid flow-paths in this unsaturated waste rock pile.

Jan 1, 2003

By E U. Petersen, D R. Cooke

Hydrogen and oxygen isotopic constraints on hydrothermal fluid composition from the Pliocene Boyongan and Bayugo porphyry copper-gold deposits (southern Philippines ) reveal mixing of magmatic and sea water reservoirs as the hydrothermal system evolved. Magmatic-equilibrated fluids (d18O: +8.3ë to +9.1ë; dD: -61ë to -51ë) are represented by hypersaline brines implicated in copper-gold transport and deposition. These dominate the fluid inclusion assemblage in early comb-quartz (unidirectional solidification textures), miarolitic quartz, and in K-silicate-stage quartz-K-feldspar ¦ biotite veins. Fluids responsible for post-K-silicate alteration assemblages of pyrite-clay (illite, pyrophyllite and kaolinite), alunite and smectite are represented by low-moderate salinity two-phase inclusions in co-existing quartz. These are interpreted as mixtures of evolved magmatic fluids (d18O dD: -42ë to -20ë) with evolved Pliocene sea water (d18O: + 4.0ë; dD: +4ë). The isotopic evidence for sea water involvement in the hydrothermal system suggests that porphyry emplacement and associated diatreme formation could have occurred in a submarine setting. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

Carbonate replacement tin deposits in the areas studiedhere are genetically related to biotite granites. Biotite in the granites is distinguished by distinctive compositional features. High MgO content is found in biotite in the Renison Bell granite; high MnO and A1203 contents in the Gejiu granite; and high FeO content in the Xinlu granite. The compositional features of biotite in the granites are reflected in skarn minerals formed around the granites.Granites associated with these tin deposits are characterized by different accessory minerals. Magnetite-bearing granite in the Xinlu deposit is related to the andraditic garnet (andradite 40-45 mole%)-hedenbergite skarn, with tin mineralization occurring in the contact skarn only. The sphene-bearing granite in the Gejiu deposit is related to the grossular garnet (grossular 50-60 mole%, almandine 20-30 mole%) -salite skarn, with tin mineralization occurring in the contact skarn, as well as stratabound replacement orebodies in the distal skarn. The ilmenite-bearing granite in the Dachang deposit and the Renison Bell deposit is related to the grossular-diopside skam, with tin mineralization occurring 500-1500 metres vertically and 1.5-3 km horizontally away from the granite contact.

Jan 1, 1990

By S Hapugoda, H Han, L Lu

Charcoal produced from Syzygium Zeylanicum trees was widely used in ancient Sri Lankan iron smelting practices. Charcoal made from Syzygium Zeylanicum tree trunks, branches and leaves were analysed by optical mineralogy and SEM and found to contain unusually high concentrations of calcium oxalate (CaC2O4.H2O – CaOx) crystals in plant cells. Partial and full reduction tests of a high-P Brockman ore were conducted at several temperatures with coke and coke doped with CaOx and CaCO3. It was observed that CaOx promoted reduction and generated comparatively more metallic iron in reduced samples. Furthermore, CaOx encouraged phosphorous partition into slag phases than into the metallic iron, suggesting CaOx can a potential alternative fluxing material to calcium carbonate for treating high-P iron ores in ironmaking processes.

Sep 18, 2023

By Robertson K. S, Hunter T. C

AEG-Elotherm's electromagnetic dosing channel, or Eldomet, is a recent invention enabling the transport and metering of molten metals. The development of a reliable refract- ory lining, and the use of suitable construct- ion and operating techniques has led to the successful application of the Eldomet for casting copper anodes at Copper Refineries Pty. Ltd.

Jan 1, 1974

By A G. Noble

Tunnelling for hydro-electric power projects can be a very challenging component of the overall development. In contrast to urban transportation tunnelling where the logistics for access and supply of power, water and other essentials are readily available, hydropower projects are usually in very remote locations and all necessary plant, equipment, spares and materials need to be brought in and the site must function as a self sufficient unit.For a large scheme the river diversion tunnel(s) are usually on the initial phase critical path in order to meet the non-negotiable deadline of river diversion before the onset of the wet season. A newly formed tunnelling crew, once mobilised to the site for the project, will face the first major learning curve of the project’s systems and logistics during this critical tunnelling activity.Power tunnels convey the water to the turbines in the powerhouse and are usually on the critical path for the main works, especially if the scheme comprises a powerhouse located within an underground cavern. A modern cavern arrangement requires a complex warren of various openings: access adits, ventilation/cable tunnels, shafts, surge tunnels, etc.Hydropower tunnel construction tends to be dominated by tunnel boring machine (TBMs) or drill-and-blast excavation techniques and each has its challenges in very remote locations. TBMs still have long lead times as for any type of project, but additionally require a thorough roads and bridges infrastructure assessment of the country from the port of entry to the site to ensure a problem-free delivery. In some cases the project also requires the establishment of a complete precast concrete segment production facility and the space for creation of laydown areas; there is no ‘just-in-time’ delivery mechanism applicable to typical remote hydropower sites.This paper highlights the technical and risk management considerations in the planning, design and construction of tunnels for hydropower projects. It contrasts the typical factors that govern the design of urban transportation tunnels with those for remote hydropower tunnels. The perspectives of stakeholders are provided including those of international lenders. With examples from large and small scale projects across the globe it provides an insight to all parties and in particular, those tunnellers that are working in the hydropower field for the first time.

Mar 8, 2011

By A Woodley, N C. Kunz

A mine site water balance is important for communicating information to interested stakeholders, for reporting on water performance and for anticipating and mitigating water-related risks through water use/demand forecasting. Gaining accuracy over the water balance is therefore crucial for sites to achieve best practice water management and to maintain their social license to operate. For sites that are located in high rainfall environments the water received to storage dams through run-off can represent a large proportion of the overall inputs to site; inaccuracies in these flows can therefore lead to inaccuracies in the overall site water balance.Hydrological models that estimate run-off flows are often incorporated into simulation models used for water use/demand forecasting. The Australian Water Balance Model (AWBM) is one example that has been widely applied in the Australian context. However, the calibration of AWBM in a mining context can be challenging. Through a detailed case study, we outline an approach that was used to calibrate and validate AWBM at a mine site. Commencing with a data set of monitored dam levels, a mass balance approach was used to generate an observed run-off sequence. By incorporating a portion of this observed data set into the calibration routine, we achieved a closer fit between the observed versus simulated data set compared with the base case. We conclude by highlighting opportunities for future research to improve the calibration fit through improving the quality of the input data set. This will ultimately lead to better models for run-off prediction and thereby improve the accuracy of mine site water balances.CITATION:Kunz, N C and Woodley, A, 2013. Improving the accuracy of mine site water balances through improved estimation of run-off volumes, in Proceedings Water in Mining 2013 , pp 267-272 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By Russell P

Polyurethane resin (PUR) is extensively used in almost all coal producing countries. On the local scene, PUR components suitable for underground application were selected and subsequently, trials were carried out at several coal mines. This paper describes the work at Pikes Gully Colliery (B.P.3Coal), where water flow rates of up to 4.5 m (1000 gallons) per minute, were reduced to 1-1.5 m /minute at the tirst stage of application. Subsequent trials were carried out at West Cliff Colliery (Kembla Coal and Coke). A variety of PUR chemical mixtures were tested in coal ribs and in the roof of intersections and roadways. The trial results are presented with all particular details. Using the PUR injection method, the roof, at the most difficult intersection, was stabilised and 'de-bonded' roof bolts were re-sealed. At Pikes Gully and West Cliff Collieries, 2 tonnes and 3 tonnes of PUR chemicals were injected, respectively. The technique, primarily based on German experience (Bergwerksverband), was used by Delta Control Systems Pty. Ltd. ACIRL was closely associated with the trials, which were monitored by installation of the measuring Stations.

Jan 1, 1986

By King D

Recent field experiments in the United Kingdom (Buchanan, 1979) have shown that the in-seam technique is capable of detecting a 1m fault in a 3m seam, at a range of 280m and with a resolution of ¦40m. Comparable tests in Australian collieries are proceeding. Although the practicality of an implementation of the technique on a routine basis remains to be demonstrated, the potential of the technique for the prediction of outbursts clearly warrants detailed examination. This potential will,depend, inter alia, on the level and scale of variations in elastic (and anelastic) properties of bodies of coal undergoing stresses associated with mining. Available data, mainly from studies of the seismic properties of gas saturated reservoir rocks, confirm the intuitive view that stress increases give rise to increases in seismic wave velocity and decreases in wave attenuation, markedly at low stresses (as pore spaces close with little resistance) but less so as stress increases. Such increases are of the same order as aniso- tropic effects, but should provide impedance contrast sufficient for detection by in-seam seismic methods. At higher stresses, cracks form within the rock mass. Results from research on earthquake prediction provide some clues to the behaviour of sedimentary rocks sub- jected to large stresses. In particular, the

Jan 1, 1980

Ore textures in Australian BIF-derived ores are quite complex and have formed the basis for ore genesis models, which includes hypogene upgrading or supergene upgrading then regional metamorphism for the microplaty hematite ores and supergene upgrading for the martite-goethite ores. Despite a high level of ore texture knowledge, little is known about the spatial distribution of ore textures within deposits or their relationship to downstream processing. This paper describes a new iron ore texture classification system to better understand the vertical textural zonation characteristics of Australian BIF-derived deposits, the interpreted role of recent supergene upgrading processes on modifying primary ore textures and their implications for downstream mineral processing. The iron ore textural classification scheme presented uses textural groupings defined on the basis of similarities in mineralogy, ore texture, porosity, mineral associations and hardness. The scheme is non-genetic and has been successfully applied to deposits in the Pilbara, Yilgarn and Gawler cratons. The main ore texture groups include dense martite/hematite, microplaty hematite, microplaty hematite-goethite, martite-goethite, goethite-martite and goethite-rich. Each group can be further subdivided into physically hard to softer subcategories. The ore textural groups can be divided into those interpreted to be associated with primary replacement of BIF and secondary textures resulting from more recent modification by near-surface hydration or dehydration processes. A schematic vertical section through BIF-derived deposits consists (from surface) of detritals underlain by a carapace, both of which may have been eroded, followed by a hydrated zone with replacement of primary ore martite and microplaty hematite by vitreous goethite. The hydrated zone is underlain by 0.2 - 6 m thick zones of intense dehydration and textural infilling of porosity with hematite and hydrohematite. Immediately below the dehydration zone is a strong zone of leaching, where more porous and friable ore textures occur, followed underneath by a gradational contact with primary ore. Secondary supergene processes can impact on beneficiation with hydration and leaching resulting in more difficult density separations at the concentrator stage due to reductions in density differences between ore and gangue and loss of heavy media into pores. Supergene modification of primary BIF-derived ore textures can substantially change lump metallurgical properties, with hydration and dehydration favourably increasing lump yield but reducing resistance to thermal shock whilst leaching will give the opposing outcome. The lump properties of ore textural groups appear to be relatively consistent within and between the iron ore deposits examined.

Jan 1, 2002

By B A. Webler, P Su, P C. Pistorius

Advanced high-strength steels (AHSS) typically have much higher aluminium concentrations (by an order of magnitude or more) than conventional low-carbon aluminium-killed steels. The resulting lower oxygen activity at the steel-slag interface changes the kinetics and thermodynamics of steelslag reactions. Previous work showed that the rapid transformation of alumina inclusions to spinel inclusions, and spinel to periclase, occurs because of the relatively high concentration of dissolved magnesium. In this paper, experimental results on nitrogen removal by ladle slag are compared with predictions based on the available thermodynamic databases. As in previous work, the kinetics was modelled by assuming mass transfer control, with steel or slag mass transfer limiting. The results show that significant removal of nitrogen by steel-slag reaction is possible.

Aug 21, 2024

By P Martin, A Somarin, S Bailey

Field-based research was conducted to investigate the performance of field portable X-ray fluorescence (FPXRF) in the analysis of reverse circulation (RC) drill chips in iron ore exploration. For years, FPXRF has been considered unsuitable for iron ore exploration due to the limitations of the elements it is capable of analysing for, in particular its inability to measure light elements (Mg, Al, Si, P, S). With the advent of the use of silicon drift detectors (SDD) in FPXRF, light elements are now measurable elements. However, doubt over the appropriate use of this new technology still exists due to the absence of reliable comparative field data. These doubts concerned the ability of the FPXRF data to correlate strongly with the laboratory assay of the same samples. It was believed that inconsistent grain size and other variables not being controlled would contribute greatly to this perceived unreliability.We tested RC chip samples on-site in the Pilbara, with the portable Thermo Scientific Niton XL3t X-ray fluorescence (XRF) analyser for a range of elements including Fe, Mn, Al, Si and S and then compared the results with laboratory assay data. A strong correlation indicates that the FPXRF results are reliable. Furthermore, to show the effect of simple sample preparation, we also analysed pulps of the same samples in the same way.The correlations were good for all of the elements of interest for the RC chip samples (R2 values between 0.82 and 0.9), and excellent for the pulps (R2 values between 0.89 and 1). The results also showed a direct correlation between sample preparation and improved quality of results with the FPXRF. This indicates that FPXRF can produce data from unprepared RC chips for Al and Si that, when compared with laboratory assays, is reliable for a field application in drilling and grade control. CITATION:Somarin, A, Martin, P and Bailey, S, 2013. Non-destructive analysis of diamond core for light elements using Niton field portable x-ray fluorescence, in Proceedings Iron Ore 2013 , pp 117-230 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By Stone I

Tahmoor Mine is located in the southern Sydney Basin 80km south-west of Sydney and produces 1.2 MT of Bulli Coal annually. Bord and pillar methods used to date will be supplemented by a longwall system. Difficult roof conditions have been experienced since mining began in 1979. A dominantly horizontal stressfield promotes shear failure in the thinly interbedded roof sequence of shales, laminites, siltstones and fine sandstones. General roof conditions and failure characteristics are related to the angle between the roadway direction and the principal horizontal stress direction. The apparent stressfield changes direction, magnitude and the ratio of principal horizontal components across the mine workings in response to both in situ and mining induced causes. Initial roof support of 5 x 2.1 m bolts per W-strap at in intervals, with mesh, was upgraded to include RSJ's in order to support areas of failed roof. This support system was inefficient and costly. A third system of support emphasizes roof reinforcement with full resin encapsulation of 2.1 m bolts in W-straps. The number of bolts per strap (6-8), extra butterfly straps and bolts, and W-strap spacing is determined for each area by expected roof and stress conditions. Intersections are pre-bolted and ribs are supported in some areas. Pillar dimensions, order of drivage and roadway width have each been altered to improve roof control. The intensity of roof deformation at the face varies from panel to panel and causes development rates to decrease to 30% of the maximum. 1. Manager, Tahmoor Mine, Tahmoor, N.S.W. 2. Senior Geologist, BP Coal, Picton, N.S.W. Roof conditions in each area of the mine are characterised and then projected to future development areas based on the relationship between stressfield orientation, relative roadway direction and face conditions. Planning information available includes expected development rates, roof support requirements and areas of changing conditions. Future improvements of strata control involve defining support design parameters for the range of mine conditions already seen at Tahmoor.

Jan 1, 1986

This paper presents a review of computer techniques for the automatic contouring of geological and geophysical data with output as interactive display on graph plotters or graphics terminals and passive display on automatic drafting tables. The advantages of the method of fitting a triangulated surface to randomly distributed data using an advancing front algorithm are described, as well as the technique for determining interpolated values for the production of contour line segments and a contour smoothing algorithm. This contouring method is employed by the Geological Survey of Queensland and is implemented as an interactive system. An alternative method ideally suited to randomly distributed data involves the use of piecewise parametric cubic splines. This method which is ideal for sharp variations in magnitude and areal extent typical of geophysical anomalies is discussed. The mathematics of surface interpolation using non-parametric splines and an explicit piecewise surface fitting technique are discussed. Curve tracing techniques which are suitable for automatic contouring are also presented and the inherent advantages of interactive contouring using on-line plotters and graphics terminals for previewing of displays are described.

Jan 1, 1977

By H Aral, L Malishev

The carbothermic chlorination of titaniferous materials such as rutile, synthetic rutile (SR), upgraded slag and ilmenite in a fluidised bed is an established commercial process. In this work, ilmenite sourced from the Murray Basin area of South Eastern Australia was chlorinated and an assessment of the chlorination characteristics of the ilmenite, in terms of pre-treatment, type of reductant and reaction time was made. Selective chlorination of Murray Basin ilmenite to remove Fe and Mn was achieved in this work. A synthetic rutile sample containing around 93 per cent TiO2, one per cent Fe2O3 and 0.5 per cent MgO was produced at a chlorination temperature of 1000¦C with around 25 per cent loss of Ti as TiCl4. Raising the reductant to ilmenite ratio in the chlorination reactions increased the amount of Ti chlorinated. However, complete chlorination of Murray Basin ilmenite to produce FeCl3 and TiCl4, was not achieved under the conditions used in this work. Pre-oxidation of Murray Basin ilmenite before chlorination had little affect on its reactivity, compared with æas receivedÆ ilmenite. In contrast weathered West Coast ilmenite chlorinated appreciably better than West Coast primary ilmenite, in terms of bed residues remaining and amounts of elements removed. The presence of large amounts of Mg and chrome spinel grains in the Murray Basin ilmenite used in this study are likely to make it difficult to chlorinate directly in a commercial chlorinator. However, this is not to say these ilmenites will be unsuitable for chlorination applications. Further work is needed in the separation of Mg and chrome spinel grains from Murray Basin ilmenites and the products resulting from these tests could then be assessed in terms of chlorination performance, so that further processing options can be explored.

Jan 1, 2000

By K C. Corin, N Ndamase, M Tadie

Mining operations in arid regions are compelled to reduce their consumption of fresh water. Closed water circuits are an attractive solution and, in addition to reducing freshwater consumption, have the added benefit of reducing reagent consumption as well as the environmental impact by eliminating effluent discharge. Accumulating ionic species have been shown to hinder collector adsorption which reduces the recovery of valuable minerals. Numerous studies have investigated the effect of degrading water quality on collector adsorption however there is very limited understanding as to how this takes place from an electrochemical perspective. This study therefore aims to investigate how the presence of accumulating ionic species at varying concentrations affects the electrochemical adsorption of sodium ethyl xanthate onto galena. The synthetic plant water used in this study comprised of single salt solutions to isolate the effects of the ionic species of interest. The ionic strengths were varied between 0.0242 M, 0.0727 M, 0.1212 M and 0.2426 M which correspond to University of Cape Town (UCT) Centre for Minerals Research (CMR) synthetic plant waters of 1, 3, 5 and 10SPW, respectively. Mineral rest potentials indicated how changing water quality affected xanthate-mineral interactions. Microflotation observed the impact of changing water quality on mineral floatability.

Aug 24, 2022