Search Documents

By A K. Raina, V M. S R Murthy

Rock mass response in blasting is an important element to determine the performance of a blast along with its other outcomes. The near-field monitoring for rock mass response analysis is vital for determining the behaviour of a blast; however, due to costly and cumbersome methods involved in such measurements the subject has received scant attention so far and the publications on this account are perfunctory in nature. This paper presents a non-destructive method to monitor the blast-induced pressure in the rock mass at a distance from a blasthole. The methodology of monitoring and a few examples of actual field monitoring are detailed in this paper. The responses of the rock in the near-field of a blasthole under dynamic loading have been documented to predict fragmentation and throw. The proposed method has also been used in limited cases earlier by the author to predict flyrock using a semi-empirical method and trajectory equation. The pros and cons of the method are discussed while throwing light on the actual response and the prediction of fragmentation and throw of blasted rock.CITATION:Raina, A K and Murthy, V M S R, 2015. Measurement of blast-induced pressure in bench blasting and deciphering explosive performance through rock mass response analysis – a methodology, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 501–508 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Parkes DB

The excavation of sandstone of generally medium strength for the Liverpool Link Line by Dosco Mark 2A Roadheaders has demonstrated the versatility and good performance of road- headers in suitable rock formations. A description is given of the strata traversed by the tunnels together with descriptions of equipment and crews, excavation sequences, operating difficulties and the results achiev- ed. In addition tunnel construction is des- cribed for a difficult section where there was only O.Sm clearance between invert and a four lane vehicular tunnel below, and O.5m clearance between tunnel crown and a century old sewer above.

Jan 1, 1976

By G Capes, L Morizzi, N Mitkas, E Jones, D Grant

This paper describes the mining setting for the sub-level open stoping (SLOS) mining method used at Olympic Dam (OD), and investigates the range of stope performance conditions encountered over 30 years of production, using a qualitative description of the factors influencing performance. Utilising a continuous improvement tool, the Plan-Do-Check-Act (PDCA) process, and a forward-looking rock mechanics program, the intent is to identify the key factors driving productivity and performance to create a stable and achievable long term mine plan.

Mar 15, 2021

By D Timms

The Kempfield deposit is located in the Hill End Trough, one of several intracratonic basins developed during Silurian–Devonian time, in the eastern province of the Lachlan Orogen, Eastern Australia.The deposit contains an oxide resource of 5.8 Mt @ 58 g/t Ag and a sulfide resource of 14.4 Mt @ 45 g/t Ag, 1.7 per cent Zn and 0.6 per cent Pb, classified and reported in compliance with the JORC Code. The deposit has been previously explored by a number of companies, including INCO, Shell, Jones Mining, Golden Cross Resources and recently Argent Minerals Ltd (Argent). Argent is currently completing a definitive feasibility study with a view to mining the deposit.The deposit is hosted at the boundary between the Molong High to the west, comprising Ordovician sediments and volcanic rocks and the Hill End Trough to the east, interpreted as a back-arc basin containing Silurian sediments and siliceous-feldspathic volcanic rocks. The boundary between these two strato tectonic units is an imbricate thrust fault zone known as the Copperhannia Thrust.The Kempfield deposit is hosted in felsic volcanic rocks known as the Kangaloolah Volcanics. These have been in-faulted and folded into the Middle Ordovician meta-sediments of the Coombing Formation of metasediments along the Copperhannia Thrust. The Kangaloolah Volcanics belong to the Late Silurian Mumbil Group, comprising submarine carbonate-shale facies interspersed with extensive felsic volcanic piles, which grade conformably upwards into turbiditic sandstone and siltstone sequences (interpreted to represent a deeper depositional environment). These turbiditic rocks are known as the Campbells Formation, comprising siltstone, sandstone and andesitic tuff. The rocks at Kempfield are metamorphosed to lower greenschist facies, reflected through the different type of schists.Silver, gold, lead, zinc mineralisation is hosted in barite-rich horizons, near the boundary to quartz-phyric tuffaceous rocks in submarine, immature, reworked felsic ash tuffs. Barite appears to be hosted in greatest concentrations by the coarser grained volcanoclastic sandstones and grits, whilst intercalated siltstones are volumetrically minor and tend to return low barite and silver. Mineralisation is hosted in stratiform and probably stratabound barite-rich horizons. A northeast-trending, steeply dipping, metamorphic cleavage (S1) occurs throughout the project area.

Aug 22, 2011

By Richards BG, Komdeur W

Instability in spoil piles and in high wall slopes in natural overburden has been ex- perienced at Utah's Goonyella Mine since com- mencement of operations in early 1971. Annual production targets, although gener- ally met since the commencement of operations, required modifications to stripping and mining techniques and the rapid re-scheduling of oper- ations around unstable areas, but culminated in the earlier than planned acquisition of addit- ional stripping equipment. An understanding of failure mechanisms was developed within a collaborative study of pitwall instability between Utah Development Company and the C.S.I.R.O. Division of Applied Geomechanics. Results showed that pitwall instability occurs as structurally controlled deformations along planar failure surfaces; spoil pile failures are precipitated by moist- ure ingress and subsequent loss of strength of base layer materials; highwall failures de- velop over areally extensive bedding planes in conjunction with inclined and subvertical fractures caused by overburden blast damage.

Jan 1, 1978

By N Ganjian, A Delavar, F Rashidi Nejad

Iran is one of the most seismically active countries in the world, being crossed by several major fault lines that cover at least 90 per cent of the country. As a result, earthquakes in Iran occur often and are destructive. So, it is important to consider the seismic stability and reliability of all structures including tailings dams.In this study, the tailings dam stability of the Sangan Iron Ore Mine in Khorasan Razavi, Iran is considered for the case study. The tailings storage facilities of the mine have three cells with the capacity of 45 million cubic metres. The first cell, which has three stages of dam raising, has been recently brought into operation. This cell has a downstream-raised retaining embankment. As the risk of seismicity in this area is high, seismic response of this dam was evaluated by numerical methods. To do this, appropriate models were developed for materials used in foundation and body of the embankment. Then for seismic stability analysis, Tabas (Iran – 1978) and Chi-Chi (Taiwan – 1999) earthquake acceleration simulations were applied.The results of this study indicated that the upstream portion of Stage 3 of the dam and dam crest did not experience significant horizontal displacements during earthquake period, but the downstream portion of Stage 3 of the dam showed a maximum horizontal displacement of 60 cm at the third stage of dam raising. This is three times more than what was estimated by the designer. Also, the maximum vertical displacement resulting from simulation of the Tabas earthquake was 35 cm. The results of dam response to Tabas and Chi-Chi earthquakes indicate that displacement, shear stress and pore pressure by the Tabas earthquake were higher than the case of Chi-Chi earthquake. The higher energy of Tabas earthquake and the higher frequency near to the natural frequency of Tabas earthquake could be the reasons of this difference. The results of this case study confirm that if the studied tailings dam impacted by an earthquake of a similar magnitude to Tabas, the dam will be seismically stable and the developed strains will not be significant.CITATION:Delavar, A, Rashidi Nejad, F and Ganjian, N, 2015. Seismic stability analysis of Sangan Iron Mine Project tailings dam, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 173–182 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By T Trott, G Lumley

"The mining industry suffers from a shortage of professional and other workers. Research and analysis has demonstrated a close correlation between high performance in productivity, maintenance and safety. There is also a significant correlation between engagement and performance. It is the hypothesis of the authors that mines can use a strategy of establishing themselves as a high-performance mine to attract and retain high caliber professional people: step 1 is to become best practice in equipment performance (productivity, maintenance and safety) step 2 is to brand the mine as æbest practiceÆ by sharing what has been confidential performance and outcome information with the general industry.Previous research has shown that many professional people are attracted by the prospect of a high achieving site because of the learnings and the support for continually doing better. In addition, a link has been established in previous research between productivity and safety. Operators and drivers are attracted to sites which have fewer dangerous people operating or driving. Good management delivers exceptional performance and a work site which high caliber managers and operational personnel people want to work at. The strategy requires commitment and proper execution but it can work. The strategy needs a specific approach and this paper will discuss this. A case study is provided from a mine which over a nine month period increased dragline performance by 15 per cent and reduced stress on the boom by 30 per cent. This mine paid the employees (professional and operational) $25 000/a less than the major mines but the operators and professional people would not leave; in fact, people were happy to be paid less to work there.CITATION:Lumley, G and Trott, T, 2012. Using best practice operations as a strategy for attracting and retaining professional people, in Proceedings International Mine Management 2012, pp 35-52 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 20, 2012

By J Knoblauch, D, P J. J Strobos, C Foggo

The Sally Malay Project is located 120 km north of Halls Creek in the eastern Kimberley region. Since commissioning, ongoing improvements on the plant have resulted in recoveries now greatly exceeding the initial design targets. The continual optimisation endeavours of the Sally Malay metallurgy department included an automation project that was done in close collaboration with Mintek. In this team effort, several problem areas were addressed and the FloatStar advance control system was successfully commissioned to stabilise and optimise the flotation circuit. The remote location of the Kimberley Nickel Mines operation, fly-in, fly-out roster and the current mining boom makes the acquisition of experienced flotation staff difficult. The implementation of an automated flotation control system reduces this burden and contributes to the training of inexperienced staff. This paper illustrates not only the process control improvements achieved as a result of the installation of the FloatStarÖ advanced control system, but also how it has assisted operational personnel with their understanding of the process.

Jan 1, 2006

By F Sinaga, E Widijanto

PT Freeport IndonesiaÆs Deep Ore Zone (DOZ) mine is the new underground block caving mine within the East Ertsberg Skarn System (EESS) which started production in mid-2000. The DOZ will produce 25 000 tpd using mechanised block cave mining method and will be the fourth underground mine opened within the EESS deposit. A review of the DOZ extraction bolting design was conducted in November 2000. The aim of this review was to re-evaluate the effectiveness of the current design in relation to bolt length and spacing and to challenge some questions about the technical background of the design. For instance, the influence of the rock condition on the design. To review this bolting design, several books and papers are reviewed and several experienced people have been contacted to give their opinion. The methodology used for this review is:reviewing the technical background of current design; collecting ideas and alternatives; collecting data from books and personal communication and conducting analysis; and conclusion and proposed design.

Jan 1, 2002

By E Ferrow, R Herbert, M E. Malmstr, M Fuchs

The study of microbial sulfide oxidation and oxidation rates of tailings requires the use of sterile control samples in laboratory experiments for comparison purposes. The need for sterile tailings sand is also apparent in the study of microbial communities and processes. This study compares six different methods with regard to sterilisation efficiency and investigates chemical and mineralogical changes in the samples as the result of sample treatment. In addition, the effect of sterilisation on mineral weathering rates is also studied. The efficiency of the different methods with regard to sterility is estimated by most probable numbers (MPN) of both sulfur and iron oxidising bacteria. The sterilisation methods that were compared are: washing with sterile water, washing with ethanol, applying antibiotics, repeated heating to 70¦C, autoclaving, and γ-irradiation. There are several possible drawbacks with the different methods, including the risk of an applied chemical acting as a substrate for micro-organisms in the system, and the risk of altering the tailings. The results show a substantial difference in sterilisation efficiency between the treatments. For example, autoclaving, repeated heating, ethanol and irradiation efficiently kill micro-organisms, rendering an undetectable amount of bacteria after one month of incubation, whilst washing with water exhibits virtually no microbiological effect, with a bacterial content comparable to the control. The use of antibiotics for sterilisation ranks intermediate: the lag-phase was twice as long in the antibiotics treatment compared with the controls. X-ray diffraction, optical and electron microscopy, M÷ssbauer spectroscopy, and mineral magnetism indicate no significant change in the bulk mineralogical composition. However, X-ray photoelectron spectroscopy analyses show that with some of the treatments, sulfides are partially oxidised, as indicated by the formation of sulfate and partially û oxidised sulfur species at the tailings surfaces. Aerated batch weathering experiments performed on sterilised tailings samples and untreated controls indicated that while the initial rates of element (S, Fe, Cu, Zn, Mg, Na, K, Ca) release may differ between the samples, over the course of ~100 days of experiment at pH 2 and room temperature, the rates declined toward a similar value for all samples. To conclude, there does not appear to be one perfect method for tailings sterilisation. Autoclaving and heating damage the mineral grain structure and oxidise the sulfide surfaces. Ethanol, antibiotics and rinsing greatly alter the pore water chemistry through the washing procedure. In addition, ethanol and denatured antibiotics might serve as a substrate and also, in the case of antibiotics, adhere to mineral surfaces thus obstructing chemical reactions. Irradiation seems to be the preferable method on an overall basis, although the formation of surface Fe3+ was suggested by M÷ssbauer spectroscopy.

Jan 1, 2003

By A G. Guinea

If you were reading this article in a newspaper or similar in the 1800s, you would know that the world was firmly in the grip of the Industrial Revolution. You might have been one of the families that decided that an agriculturally based existence was no longer for you, and that the promise of a factory job was more appealing and more secure. And it was. Financially at least. Not so much from a workplace safety perspective.

May 5, 2022

By D Cliff, B Belle

Trigger action response plans (TARPs) are inherent to managing multiple hazards such as high gas content with multiple coal seams, high spontaneous combustion propensity, heat and ventilation. TARPs aim to provide assurance and guidance when the situation deviates from the original plan or there is a change in conditions that could be hazardous. Over the years, learnings from various incidents have continuously required coal operations to revisit the TARP trigger values that were based on historical data or guidance values from the industry. In most cases, the background to the basis of TARP statistical data (ie average, maximum, hourly or daily for the monitoring or sampling location) is unknown. The introduction of real-time monitoring devices to monitor gases and airflows has provided greater understanding of the hazard scenarios and their controls. This paper analyses the carbon monoxide data from operating longwall mines and compares these with the historical trigger values to understand the changes and identify improvement opportunities while setting trigger levels in the TARPs. As an example of setting trigger values, those used during the sealing of a panel are explored in terms of setting values based upon the sampling location and the level of risk. It is envisaged that the learnings shared herein will further enhance the understanding and management of multiple hazards in Australian coalmines.CITATION:Belle, B and Cliff, D, 2015. Improved trigger action response plan development based upon mine-specific data, in Proceedings The Australian Mine Ventilation Conference, pp 73–78 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

The An Shan iron ore deposit is the biggest low-grade oxidised iron deposit in China. Over the past ten years, about 120 SLon verticalring-pulsating high gradient magnetic separators units have been installed in An Shan to process oxidised iron ore. This paper describes how several plants have upgraded their old technologies to new technologies with SLon magnetic separators as the key equipment for controlling tails grades, including using reverse flotation as the key technology for iron concentrate cleaning, These plants have been modernised with beneficial results at low cost.

Jan 1, 2009

By W D. Rech, K W. Keskimaki

As an integral part of the conversion from rail haulage to conveyor haulage at Henderson, over six kilometres of drifting and several large complex openings were mined. The deepest of these areas was nearly two kilometres beneath the surface, bringing all of the challenges of rock stress and heat that come with mining at these depths. Though many mines operate at these depths, the development of the infrastructure necessary to support a 36 000 tonne per day caving operation brought some unique challenges to the development mining activity. The issues handled include: finding experienced staff for a æfast trackÆ development program; rock bursts and ground conditions; inflow of 50 degree centigrade water; acceleration of the project completion; large diameter raise boring and difficult muck handling.

Jan 1, 2000

By W P. Darcey

Jabiru Metals completed a feasibility study on the Jaguar Base Metal Project in July 2005. The study was based on conventional truck haulage via a decline. Conveyor haulage was considered but not in sufficient detail to provide a meaningful comparison. The current study investigates the cost and productivity of alternative ore transport systems for the Jaguar project. The options considered are conventional underground truck, conveyor, road train, rigid frame truck, monorail haulage and shaft hoisting. Shaft hoisting was not considered in detail due to the high capital outlay for such a relatively short mine life of less than six years. This study goes beyond the common approach of evaluating haulage systems in isolation; it includes development costs, timing of ore production and costs associated with mine services as well as administration and milling costs. The results of this study indicate that the best haulage option for the Jaguar project is conventional truck using the Hitachi AH400 trucks. The net present value (NPV) for this option is A$8.13 million higher than the next best option namely the Kiruna E635 electric truck. The conveyor option has the lowest operating cost per tonne of ore but the longer development time negatively impacts on its NPV. The monorail option is considered impractical due to the number and length of trains required to achieve production targets.

Mar 21, 2011

By K Saito, M Hasegawa

Removing sulfur and phosphorus from molten iron can be expressed by the following reactions, respectively. [S]Fe + (O2-)slag = (S2-)slag + [O]Fe [P]Fe + (3/2) (O2-)slag + (5/2) (FeO)slag = (PO43-)slag + (5/2) Fe(liquid) These equations indicate that desulfurisation and dephosphorisation have opposite oxygen potential conditions. If a small amount of desulfurisation slag not removed is carried over to dephosphorisation process, the reaction of sulfur mentioned above proceeds toward left hand resulting in increasing sulfur content in molten iron. For better understanding of such re-sulfurisation reaction in hot metal pre-treatments, the present study aimed at evaluating the effect of iron oxide on the sulfur distribution ratio between slag and hot metal. To measure sulfide capacities and FeO activities simultaneously at temperatures below the melting point of pure iron, CaO-SiO2-FeO and CaO-Al2O3-FeO ternary molten slags were brought into equilibria with copper-iron-sulfur liquid alloys, and the equilibrium oxygen partial pressures were determined with an electrochemical technique involving the stabilised zirconia solid electrolyte. The experimental results showed that the sulfide capacity increased with an increase in FeO content, and this trend was consistent with the fact that FeO was basic. Although the addition of FeO raised the FeO activity and oxygen potential, the calculated value for sulfur distribution ratio between slag and hot metal increased with increasing FeO content.

Jun 19, 2024

By D Kentwell

A resource model serves two main purposes depending on the stage of a project. The first is to provide an early indication of likely tonnages and grades at certain cut-offs so that decisions can be made on whether continued spending on the project is justified. The second is to provide a basis for mine planning, feasibility studies and reserves. Resource models are not designed for selection of actual blocks in the ground for processing. This is the purpose of a grade control model, which is created at a stage beyond both resources and reserves.Inferred, Indicated and Measured Resources contain different levels of uncertainty with respect to the accuracy of the resulting grade and tonnage curves. These uncertainties arise from three broad areas: quality of information, geological assumptions and estimation technique. This paper focuses on known problems with the ordinary kriging (OK) estimation technique. Resource estimates often produce smoothed block grade distributions with much lower block grade variability than true selective mining unit (SMU) block grade distributions. There are two main factors that are involved in this smoothing. Firstly, where the block size used for estimation is larger than the SMU block size, this will smooth the block grade distribution and move the grade and tonnage curves away from the true SMU block grade and tonnage curves. Secondly, and less well recognised, is that smoothing is inherent in the OK estimator. This also moves the grade and tonnage curves away from the true SMU grade and tonnage curves, even when the estimate is done at the SMU block size. There are a number of techniques, such as simulation, uniform conditioning and degraded search neighbourhoods that can provide a better approximation of the true SMU block grade and tonnage curves at the expense of individual block accuracy.This paper aims to explore the extent to which OK resource estimates designed to maximise individual block accuracy can differ from (an estimate of) the true resource at SMU block size in terms of grade and tonnage curves. The differences at economic cut-offs and above are examined. In some cases these differences are significant. Both the OK estimation technique and block size play a part in the differences observed. To do this we will examine a number of commodities and deposit types using real project data.The conclusion is that the current industry standard default practice of targeting maximum individual block accuracy (conditional unbiasedness) using OK at resource stage, without consideration or evaluation of the extent of associated smoothing at SMU scale, can lead to significant errors in fundamental mine planning decisions. This then has implications for resource classification if the classifications are based heavily on the OK quality without consideration of the true SMU distribution.CITATION:Kentwell, D, 2014. Aligning resource estimates with mine planning, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 185–192 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By A G. Tomkins

"Approximately 32 per cent of the worldÆs total gold production has come from greenstone belts (Frimmel, 2008). In these regions numerous small to large, quartz vein-associated gold deposits are hosted in metamorphic rocks ranging from lower greenschist to granulite facies. Historical exploration has focused its efforts on rocks of greenschist to lower amphibolite facies because these seem to contain the most deposits. Consequently, these regions are now reaching mature brownfield status, particularly in developed nations, and finding new deposits is becoming progressively more difficult. In comparison, regions of similar tectonic setting, but instead containing high-grade metamorphic rocks of mid-amphibolite to granulite facies, have received little attention because the first explorers found fewer deposits there.However, these regions certainly do contain some very significant gold deposits such as Hemlo in Canada (~684 t Au), Renco in Zimbabwe (~31 t Au mined since 1980), the very profitable Challenger deposit in South Australia (~36 t Au; recovered + reserve + resource), and the most recently discovered Tropicana deposit in Western Australia (~182 t Au; reserve + resource). High-grade metamorphic terrains therefore offer explorationists an excellent opportunity to move onto relatively green fields within developed nations, which carry less risk associated with development. However, explorationists have comparatively little knowledge of the geological controls on gold distribution in high-grade terranes because: industry experience lies in traditional lode-style gold deposits these gold deposits are geologically more complex there has simply been minimal research conducted on these deposits as a holistic group.Furthermore, research conducted in the last five years has shown us that the previous widely accepted model for gold genesis in these terranes, the crustal continuum model, is incorrect. Here, I discuss features from several gold deposits hosted in high-grade metamorphic rocks and use these to define two categories for explorationists to consider: deposits that formed prior to peak metamorphism (metamorphosed gold deposits) deposits that formed well after peak metamorphism (post-metamorphic gold deposits). There are none that have been convincingly shown to have formed during peak metamorphism.CITATION:Tomkins, A G, 2013. Gold deposits in highly metamorphosed terranes, in Proceedings World Gold 2013, pp 23-26 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 26, 2013

Central to any business is its Asset Management Plan which encapsulates the business context and key organisational objectives such as profitability, safety and environmental standards. Life Cycle Planning (LCP) is a key component of an overall Asset Management Plan. A comprehensive approach to Life Cycle Planning forecasts the financial expenditure required to support the performance of the asset over the business life. It incorporates capital, maintenance and operational expenditure along with an estimation of economic life. Within its body the LCP provides the detail of the maintenance plan and method of its execution. Once optimised the LCP becomes the overarching plan executed through the application of several elements of the Asset Management Plan to ensure the return on investment from the assets is optimal. Each of the elements of the LCP is bound by a set of loops that provide information based on the analysis of outcomes. These loops drive the continuous improvement of performance and cost over the life of the asset. In this way we ensure that the LCP is a dynamic plan responsive to the changing business environment. The paper being presented today will describe the process undertaken and the outcomes derived when this approach was applied to a $600 M+ coal handling and preparation plant in QueenslandÆs Bowen Basin. It will also delve into the difficulties encountered from both technical and cultural aspects; the latter proving to be the most difficult to manage. It will describe the hurdles and barriers that hampered progress including the human influences and the natural desire to revert to what has been done in the past when things became a bit difficult. In the end the results are there to show that the upfront expenditure and investment in time was time and money well spent and the outcome has the operation well placed to manage the assets in a manner designed to deliver the optimal business outcome.

Jan 1, 2007

During operations, mining and metallurgical processes may generate effluents such as tailings water, acid mine drainage (AMD) and seepage and process acid streams. Depending on the type of ore and the metallurgical process, these effluents may contain one or more toxic compounds (eg acidity or alkalinity, cyanide, ammonia and/or nitrate, heavy metals, total suspended solids (TSS), sulfate) in elevated concentrations requiring treatment before their discharge to the environment or recycle/reuse in the process. Natural oxidation of sulfide minerals present in mining wastes (eg tailings and waste rock) at mining sites may generate AMD, which is characterised as a low pH, high acidity effluent containing heavy metals and sulfate. If generation of AMD cannot be controlled and/or prevented, AMD needs to be collected and treated for neutralisation of acidity and reduction of metals and TSS to meet regulated water quality standards. It is important to note that some of these compounds may persist in run-off from mine sites, even after the mine and processing facilities are decommissioned. Treatment of mining and metallurgical process effluents can be accomplished by means of various physical, chemical and/or biological methods. The mode of process application may vary from the use of either specifically designed, controlled and automated facilities or passive systems. Lime neutralisation and precipitation is the most common method used in the mining industry to treat AMD. To reduce the problems associated with disposal and long-term storage of the resulting sludge, the use of a high-density sludge process (HDS) has become a preferred option. The use of other chemical reagents, waste or by-products from other industries, and biological sulfate reduction methods can also be considered as viable options for site-specific situations. Recently, several passive treatment systems have been designed and successfully operated, even in the cold North American climate. This paper will discuss available options and provide insights for selecting a suitable method for a given situation using case studies from projects conducted by Golder Associates around the world over the last decade.

Jan 1, 2006