Search Documents

By D A. Williams, P J. Chapman

The acceptable rate of rise of the tailings beaches on upstream-raised tailings storage facilities (TSFs) is critical to life of mine planning. This is illustrated through a case study in Western Australia presented in this paper. Accurate estimates of expected beach slopes, the maximum rate of rise at which the tailings can be placed, and the dry density that the tailings solids will achieve after deposition (stored density) are required in order to design TSFs that will allow upstream raises to be constructed safely and economically. Where operations have been occurring for some time, these three parameters are able to be measured and can be well-defined. If process plant throughputs are proposed to increase through mine expansion, for example, increasing the rate of rise of the tailings can compromise the potential for upstream TSF raising, thus influencing the viability of such an expansion, the timing for its implementation, and significantly increase costs.This paper outlines how rate of rise can be a key constraint, and that ‘rules of thumb’ that are typically applied may not result in the outcomes they were meant to achieve. An example of an experimental method to justify an increase to the ‘rule of thumb’ ~2.5 m/year limit for gold tailings in a semi-arid climatic setting is discussed, followed by rate of rise modelling that ultimately framed the decision-making process for a mine expansion. The rate of rise modelling method was adopted to carefully distribute tailings deposition across four TSFs, comprising nine separate tailings cells, in order to maintain appropriate rates of rise. The implications resulting from various deposition splits are presented, including the need for expansion. In addition, this paper outlines the effect of rate of rise on the state (density) of the tailings after deposition, and provides commentary on how anecdotally acceptable rates of rise, based on the aforementioned ‘rule of thumb’ of 2.5 m/year may not provide assurance of geotechnical stability through the tailings achieving a dilative state, as has been thought in the past. An example of the influence of rate of rise on the state of the tailings, with respect to air-drying and the critical state line (CSL) for the material, is presented. The data indicate that reducing the rate of rise may allow a higher dry density to be achieved through air-drying (evaporative desiccation), sufficient to move the material from the contractive to the dilative zone (i.e. from above the CSL, to sufficiently below it).CITATION:Chapman, P J and Williams, D A, 2018. The importance of rate of rise in life-of-mine planning of an upstream raised tailings storage facility – a case study, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 350–360 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By G J. Harbort, K Lam, C Sola

The relationship between the geology of porphyry copper deposits and their processing performance is an area of interest. Being able to predict comminution properties of the ore from physical characteristics and geological descriptions would allow an increase in the precision of capital cost estimates, operating cost estimates and throughput rates. This geometallurgical approach would reduce the requirements for expensive comminution tests.As the comminution circuit is the highest capital cost item in the plant and a possible throughput bottleneck, understanding the variability in hardness within the orebody is critical. A geometallurgical model allows calculation of ore hardness values in mining blocks from ore characterisation data. This model subsequently uses a combination of simulation and power-based approaches to relate ore hardness and flotation feed size to grinding circuit throughput.This paper reviews the geometallurgical models developed for seven porphyry copper deposits and discusses the strengths and shortfalls of the methodology and similarities and differences between the different deposits.CITATION:Harbort, G J, Lam, K and Sola, C, 2013. The use of geometallurgy to estimate comminution parameters within porphyry copper deposits, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 217-230 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By A Parbhakar-Fox, S C. Dominy

The prediction of acid and metalliferous drainage (AMD) from mine waste materials is critically important during all stages of the mine value chain. However, to determine such geoenvironmental characteristics static and kinetic testing of individual waste units must be performed on representative samples. The importance of sample selection cannot be underestimated; it is the single most critical aspect of any geoenvironmental investigation. Poor sampling techniques and inadequate sample selection will contribute to excessive variance, difficulties in interpretation and incorrect assessment. By undertaking mesotextural characterisation based on hyperspectral mineralogical data (with sulfur assay data if available), opportunities to improve sampling strategies are presented. Such data will inform the selection of samples for low-cost total sulfur, paste pH and geoenvironmental logging, which collectively will allow for accurate AMD forecasting and improved sampling practices to be achieved. Once sampled, robust quality assurance/quality control (QA/QC) protocols must be developed where the use of international certified reference standards become obligatory. This is currently not practised, resulting in inter-laboratory discrepancies when undertaking waste classification. Further improvements in geoenvironmental characterisation testing lies in the adoption of blended static testing protocols, whereby blends of waste materials can be efficiently tested so as to give an early forecast as to whether they will produce acidic or metal-laden drainage. Such information is integral in developing a waste schedule that will allow for a non-acid forming waste landform to be constructed right from the start of the operational phase. Ultimately, improvements in this discipline lie in technological innovations with regards to mineralogical characterisation, and by offering geoscience and minerals engineering students a competent education in the discipline. Collectively, this will empower a step-change in AMD prediction and waste handling, and will make the realisation of the United Nations Sustainable Development Goals a reality, rather than a dream.CITATION:Parbhakar-Fox, A and Dominy, S C, 2017. Sampling and blending in geoenvironmental campaigns – current practice and future opportunities, in Proceedings Eighth World Conference on Sampling and Blending , pp 45–54 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By D Mcleod, S Brindley, S Green

The design and engineering of flotation circuits is driven by numerous inputs, including (in no particular order) testwork outcomes, site considerations, type of separation required, energy sensitivity of the flotation response, personal experience and preference for flotation machines, maintenance access requirements, operability, level of automation and capital constraints.This paper discusses these and other issues in the Australian context and covers the flotation of copper/gold ores and polymetallic (copper/lead/zinc) ores. The paper discusses aspects of the following: how should testwork be done and what are the important inputs and outcomes? how should testwork results be interpreted and how does this impact on equipment selection? what processes can have a critical impact on flotation circuit performance, eg thickening and regrind? what options are available with the typical æflatÆ Australia site? how do you minimise capital cost and what impact can this have on flotation circuit operation and maintenance? how should circuits be controlled and operated? Particular focus is placed on some practical aspects of process design and engineering and the potential impact that engineering decisions can have on flotation plant operation.

Jan 1, 2005

By C M. Standen

The SAG mill at Rasp Mine has undergone a number of liner design modifications since commissioning in 2012, making liner wear and failure difficult to predict from historical data. During 2017, several instances of liner failure or near failure were experienced resulting in unplanned downtime for emergency relines or to patch liners in the lead up to a planned shutdown. The strategy for relining mills is often to minimise the frequency of relines (and subsequent shutdown costs) by extending liner life, achieved through design modifications. However, it was observed that as the Rasp SAG mill liners wear, mill performance declined with power draw increasing and throughput declining. Opportunity and inefficiency costs start to erode the revenue per additional tonne milled for a given set of liners, and in turn the benefit of delaying relines. As such, optimising the frequency of relines becomes a trade-off between reline costs and opportunity/inefficiency costs in delaying relines. The aim of this paper is to demonstrate a frame work for analysing costs using a marginal economic analysis with the assumption that the Law of Diminishing Returns can be applied to the life of mill liners. The SAG mill operating variables can be modelled to determine their impact on costs and an optimal reline point can be defined where the total costs are minimised. This prevents unexpected failures due to accelerated wear by providing justification to reline earlier and thereby allowing efforts to be focused on sustaining milling performance.CITATION:Standen, C M, 2018. An economic approach to optimising mill reline frequency – a case study of SAG mill relines at Rasp mine, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 197–206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By D Howe

The Athena gold deposit was discovered in 2007 by Gold Fields Australia Ltd, at the St Ives Gold Mine, 35 km southeast of Kambalda, Western Australia. Gold anomalism was identified in sheared Paringa Basalt as a result of a regional scale aircore drilling program, in association with geophysics. In the 18 months following discovery, the deposit was intensely drilled and by June 2009, it was announced that the Athena deposit contained an ore reserve of 1.7 Mt @ 5.6 g/t for 316 koz. This was followed by a feasibility study, and as a result mine development commenced in November 2009.The Athena mineralisation is hosted in a discrete, north-south striking, steep to moderately dipping shear zone within the southwest dipping Paringa Basalt. Vein intensity has a strong correlation to grade and vein type varies from early thin quartz-albite-sulfide (pyrite and/or pyrrhotite) shear parallel veins to strong brecciation and irregular veining with quartz-albite-actinolite-biotite-pyrrhotite infill. The geology preproduction process developed at the Argo mine was refined and improved following a business improvement project. The aim of the process is to construct detailed geological interpretations prior to development allowing informed mining decisions to be made. The process delivers significant cost savings and revenue enhancements.The development of macroscopic classification scheme was critical to determine ore or waste in the early phases of mining. The Style of Deformation, Alteration and Veining (SAV) Code was the result, and has been enhanced as greater geological knowledge is gained over time.

Aug 22, 2011

By R Kroukamp, G Rech

CRONIMET Australia in cooperation with Speciality Metals International, the mining lease holder of the Mt Carbine Tungsten mine, have demonstrated the preconcentration and processing of large (>12 million tonnes) tailings and mine waste dumps on site in far north Queensland. The first stage of this project has proven the economic viability of preconcentration using sensor-based particle sorting whilst ensuring high recovery of industry critical tungsten minerals – wolframite and scheelite. Sensor-based sorting technology have enabled the production of a sorter product to feed the existing wet gravity plant ensuring higher recoveries and increasing concentrate production. Processing of 1,000 tonne low grade samples using the TOMRA x-ray transmission (XRT) ore sorter installed on site, has reduced the volume of material entering the downstream wet processing plant by up to 60%. The sorted 10-25mm size range produced the highest upgrade ratio (product/feed) of 24:1 and achieved sorter concentrate grade of 1.52% WO3, sorter waste grades below 0.014% WO3 and metal recoveries of up to 93.4%. The appropriately sized, barren sorter waste material is also sold as aggregate and other quarrying products and thus adding to the overall economic benefit of the project. The utilisation of the sorting technology on site has produced an economically viable project, significantly reduced capital cost, and reduced the time to market of the final tungsten concentrate. The next phase of the project includes design and installation of a larger two sorter plant capable of over 150t/h feedrate.

Nov 10, 2020

By W Akpan

The Royal Bafokeng community in South AfricaÆs North West Province represents a unique case in Sub-Saharan Africa in terms of its positioning in the natural resource economy. It receives royalties directly from mining firms for the extraction of Platinum Group Metals, which include platinum, ferrochrome, rhodium and palladium. In 2007, royalty income of about R290 million (approximately US$32.2 million) was reported. Such direct revenues have enabled the community to invest in educational, medical and other social infrastructure, thus complementing governmentÆs social provisioning efforts. Indeed, the Bafokeng community owes its present-day modernisation efforts to mineral rights, and in particular, the legal-institutional arrangement that has enabled it to play an active role in South AfricaÆs lucrative extractive economy. However, the distribution of platinum wealth in this community is not only uneven, but also appears to have had little impact on the broader socio-economic conditions in the community. Despite claims by community leaders of heavy investment in education and skills development, the community continues to be faced with very high levels of unemployment, illiteracy, sprawling informal settlements, poor access to medical facilities and malnutrition. This paper examines the sociological paradoxes and contradictions thrown up by the approach adopted to involve community members in the mobilisation of mining royalties for developmental ends. The central argument is that the current æmodelÆ contradicts the communityÆs stated goals of using platinum wealth to drive up broad-based development and modernisation. This is mainly because it leaves out the vast majority of community members, who are uneducated and unskilled. The core analysis is based on pilot data from an ongoing study in the Royal Bafokeng community.

Jan 1, 2009

By R Stead

So many ceramics look the same, but are they?In the past 20 years, there have been significant changes in the materials available, as well as changes to the supply chain, for ceramics used in wear applications in the hard rock mining industry. The biggest change in supply has been from the Chinese market, with many suppliers promoting their products as æstate of the artÆ. Some of them are state of the art, but are they all? There will be some concluding remarks in this respect.There are still some outstanding new developments coming from the more traditional suppliers and these should not be ignored. However, as an end user, how can one be sure that the product received meets the technical specifications of that material?This paper will address some of the questions on how to differentiate between different materials by giving a technical overview of the current (but not exclusive) range of popular ceramics, plus incorporating how these ceramics are used in process plant products by presenting case studies. The presentation will include technical data coupled with micrographs of various ceramics to illustrate just why they are different.It will also be shown that by careful selection of the wear material, it is possible to gain significant benefit when using superior materials in an ore processing plant. The impact of cost of the products, life, process efficiency, and reduced maintenance costs will be considered using cyclone components as an example.The properties (including the microstructures) of the various ceramics will be compared to the application in order to get some understanding of what is considered good or bad.Misra and Finnie (1982) summarised their paper, æA review of Abrasive Wear of MetalsÆ by saying:à it is difficult to give guidelines for selecting materials for abrasive wear resistance. Each application is a different one, and a design engineer has to take into account various other factors such as impact, fatigue and corrosion which are often coupled with abrasive wear. The same applies to ceramics.CITATION:Stead, R, 2013. Applications of ceramic wear materials in the gold industry, in Proceedings World Gold 2013, pp 325-330 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By C Simpson, J M. F Clout, G Plummer

Detrital iron deposits (‘DID’) in the Hamersley Province of Western Australia have been successfully mined and processed as small quantities of saleable standalone or blended lump and fine ore products over many decades. Despite their past, present, and potential future exploitation, they have received far less geological attention than the economically more significant higher grade bedded iron deposits (BID) or channel iron deposits (CID). DID are composed of Pliocene to Quaternary unconsolidated colluvial/alluvial hematite gravels with minor sand, silt, and ferruginous clay, as well as minor iron rich hematite clast conglomerates. DID mineralisation at Solomon has been subdivided into six distinct stratigraphic units, DID-5 (lowermost) to DID-0 (uppermost) based on differences in clast and matrix textures and mineralogy, degree of consolidation/lithification, particle size distribution and replacement textures. The most significant accumulations of DID-1 to DID-5 are in tributary valleys that have been cut through the Joffre Member of the Brockman Iron Formation on either side of the main Kings-Queens valley which contains the CID. DID-5 and DID-4 are ferruginous conglomerate, referred to as canga, with four subtypes recognised. DID-4 is composed of BID hematite clasts cemented by hematite or goethite. DID-5 is characterised by partial to complete replacement of BID hematite clasts and matrix by the yellow ochreous and brown to black vitreous forms of goethite. DID-3 to DID-0 are unconsolidated hematite detritals composed of largely (>80 weight per cent) fine to coarse gravel, minor sand and little silt or clay. The gravel clasts are largely composed of hematite and hydrohematite that replace BID, micro-nanoplaty hematite-martite-ochreous goethite (m-nplH-M-oG) BID, reworked canga, hematite pisoids, siliceous hematite BID (micro-nanoplaty hematite-martite-quartz, m-nplH-M-quartz), chert (~10–20 per cent) and minor (<5 per cent) Banded Iron Formation (BIF). Hematite abundance decreases from DID-3 to DID-0 whilst siliceous hematite BID is highest in abundance in DID-0 and lowest in DID-3. A key finding of the study is that >90 per cent of mineralised detrital clasts are derived from hypogene altered BID micro-nanoplaty hematite-martite with subsequent later supergene ochreous goethite mineralisation hosted by the Joffre Member. The DID genesis model entails interpreted Palaeoproterozoic siliceous hematite hypogene microplaty BID mineralisation of the Joffre Member undergoing Cenozoic supergene leaching of quartz and replacement by ochreous goethite to form low phosphorous BID micro-nanoplaty hematite-martite-ochreous goethite clasts. BID martitenanoplaty hematite-martite-ochreous goethite clasts and detritus eroded from hill slopes were deposited in the valleys as an initial single DID-5-DID-4 unit over a weathered pre-CID basal conglomerate. DID-5 and DID-4 underwent goethite cementation of the matrix followed by replacement by hydrohematite, hematite, and maghemite. DID-3 formed during subsequent periods of erosion of largely DID-4 hematite clasts and pisoids. Groundwater flow-through hematite canga resulted in partial to complete hydration replacement of DID-4 hematite clasts and matrix by ochreous and vitreous goethite to form DID-5. Deposition of DID-2 to DID-0 was via reworking and deposition of DID-5 to DID-4 canga and DID-3 as clasts and pisoids/ooids, as well as siliceous hematite and BIF sourced from the Joffre Member in the hill slopes.

Nov 8, 2021

By P Walker, I Crnkovic, D Bennett

The Phu Kham deposit represents a copper-gold porphyry system, with mineralisation present in skarn, stockwork and disseminated styles. Significant folding and alteration events have created a complex heterogeneous mineralogy horizon. Weathering and water table contact have created a leached zone, overlying transition zones with supergene chalcocite- dominant secondary copper mineralisation and clay-rich gangue. Primary ore copper mineralisation is mainly chalcopyrite with minor bornite. The major challenges to the copper-gold flotation process are a wide size distribution of chalcopyrite mineralisation and poor primary grind liberation, a high pyrite content in skarn ore requiring aggressive pyrite depression conditions, clay-rich gangue and non-sulfide copper mineralisation in weathered zones, and a significant association of gold with pyrite.The Phu Kham concentrator has been developed as a conventional semi-autogenous grinding (SAG) and ball milling circuit followed by selective rougher flotation, regrinding and cleaner flotation to produce a copper concentrate containing payable gold and silver values. The concentrator flow sheet design offered a capital efficient compromise between high copper recovery bulk sulfide flotation with large cleaning capacity, and lower recovery copper selective rougher flotation to ensure concentrate specification of 24 per cent copper grade could be achieved. This paper will examine and discuss concentrator flow sheet development, including projects implemented since commissioning to improve copper recovery, and future projects designed to maintain and enhance copper in concentrate production with decreasing copper grade and increasing pyrite content of ore feed, and increasing hardness of primary ore.CITATION:Bennett, D, Crnkovic, I and Walker, P, 2012. Recent process developments at the Phu Kham Copper-Gold Concentrator, Laos, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 257-272 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By A Mooney, G Balog, P Burns, R Brooks

This paper outlines the rationale for the location of the crusher, geotechnical analysis and basis of ground support design, design and scheduling of the chamber and supporting excavations as well as the operational outcomes and lessons learned. Contributions from mining operations, planning, geotechnical and infrastructure teams enabled the Crusher Station One excavation to be completed on schedule, with opportunities taken for underground mining and infrastructure to work safely in parallel to deliver crusher station infrastructure on schedule. Installation of crusher infrastructure was ongoing at the time of writing.

Mar 15, 2021

By J Samosir, L A. Snyman

Northparkes is located 27 km north of the township of Parkes in central New South Wales, Australia. The operations consist of underground block cave mines and an ore processing plant that produces high-grade copper and gold concentrate. Production is currently sourced from the E48 Lift 1 block cave mine and open cut stockpiles. Mining commenced at Northparkes in 1994 as an open cut operation. Underground block cave mining began in 1997. Northparkes was the first mine in Australia to use the highly efficient block cave mining method, which relies on gravity and natural rock stresses to fragment the ore.An issue affecting production in 2011 was the stability of the E48 mine. A small portion of the drives on the extraction level began to deteriorate as the ground support system failed. The problem was temporarily fixed by stopping production in three extraction drives and tight filling selected areas within these drives (and drawpoints) with low-strength concrete. This action provided immediate support and stability whilst allowing time to investigate potential ground support remedies. From these investigations it was decided to use resin injection technology and additional ground support to stabilise the rock in the aforementioned extraction drives as the concrete plug was excavated in a controlled advance and sequence. This made the area safe and ensured the ongoing safe operation of the E48 mine. The redevelopment of one of these drives began late in 2011, with the remainder being progressively redeveloped over the next two years in order to maintain the extraction level stability.This paper looks at the strategies employed to safely re-open previously converged drawpoints and associated extraction drives that were subject to high abutment loading that was possibly associated with premature cave breakthrough.CITATION:Samosir, J and Snyman, L A, 2014. Redevelopment at Northparkes following significant drive closure, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 87–92 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

The problem of comparison of island arc&apos;s andesites in terms of petrochemical data is exa- mined. It is definitely established that only two main factors exist controlling the petroche- mical variety of the Kurile arc&apos;s andesites.Ori final multivariate statistical technique and computer software are used to extract these fac- tors. It is shown as well that the chemical com- position of igneous rocks depends on the type and structure of the Earth&apos;s crust. The follo- ~cing interpretation is proposed for the two factors describing petrochemistry of andesites: the first one is the depth to the Benioff seis- mofocal zone and the second one is supposed to indicate the position of the peripheral magma chambers. The basic trends of variations in the chemical composition components depending on the changes in the controlling factors are de- Tcnnined.

Jan 1, 1987

By I Lourel

In evaluating the installation of an in-pit crushing and conveying (IPCC) system for any mine, a number of options are available for each of the dig side, transport and dump side operations. Some of them are moreappropriate than others; given the pit arrangement, the material being handled and the rates at which it needs to be moved. This paper seeks to document the options that might be employed, and to rank them in terms of their applicability at any mine and their practicality overall, with a view to nominating those that would be most suitable for further study.

Jan 1, 2009

By D Liu, M Edraki, L Berry

The presence of clay minerals slows down the settling rate and mitigates compact consolidation efficiency in tailings dewatering. The increasing use of saline water in many plants, affects the dewatering performance and presents the mining industry with new concerns. Efficient tailings dewatering is a great challenge due to the complexity character of tailings, especially clay mineralogy, clay content, and water chemistry. In this study, existing studies of the effect of different affecting parameters, such as pH, ionic strength and polymer flocculants, on clay aggregation behaviours are reviewed. The settling behaviours of three types of commonly observed clay minerals in tailings, kaolinite, bentonite, and illite, are also investigated in saline water with different water salinity as a case study. The settling rates of clay minerals are found to be affected by water salinity, clay type, clay content and polymer dosage levels. High salinity water hinders the settling of kaolinite but assists the settling of bentonite and illite through formation of different aggregation structures.The current work has indicated that strategies to promote more rapid dewatering could include adjusting flocculant type or level, water salinity and salt balance, and tailings solid content levels. Implementing dewatering strategies may require a more detailed knowledge of the effect of surface chemistry on the nature and strength of the clay inter-particle forces. This study discusses the research gaps on how to better manage clay-rich tailings in saline water and identifies new research directions. The development of a water management model, supported through in-line monitoring data to predict and manipulate of the surface chemistry of the clay component of the tailings could be a new direction to manage the issues associated with clay minerals in the process of dewatering and tailings management. Mine planning (water use requirements, operating costs) could benefit from more detailed studies on dewatering of clay-rich tailings in saline water. CITATION:Liu, D, Edraki, M and Berry, L, 2018. Improving the dewatering efficiency of clay-rich tailings in saline water, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 476–484 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By P Gehrke, S O’Gorman

The precise measurement of NO2 was historically difficult in road tunnels, hence criteria and design analysis was based on converting from NOx concentrations via a set NO2:NOx ratio. The reliable direct measurement of NO2 is now possible, however design analysis is still dominated by emissions tables and formulas specified in terms of NOx. For converting from NOx to NO2 in a road tunnel environment in Australia, the ratio has typically been assumed to be ten?per?cent. This has generally been based on the recommendation in PIARC (2000) and on the ‘average’ value cited in PIARC (1995).Determining this ratio is important as changes in engine technology and in-tunnel pollution criteria along with improvements in CO and particulate emissions control, may mean that NO2 will become the driving factor for future ventilation requirements. Correct selection of this ratio can directly impact the ventilation capacity and system design.Recent research has indicated that choosing a constant ratio of ten?per?cent for all tunnels may not be appropriate. The in-tunnel ratio has been estimated to be as much as 20?per?cent to 30?per?cent and depends on the location in the tunnel, the type of ventilation system and the traffic/fleet characteristics. This paper discusses the effect of some of these parameters on the NO2:NOx ratio in road tunnels.The findings indicate that the ten?per?cent upper limit on the NO2:NOx ratio in PIARC (2000) may be a conservative value for design purposes for longitudinally ventilated road tunnels of typical length in Australia. A value of seven?per?cent to eight?per?cent may be more appropriate in some circumstances. However, the value chosen will depend on the specific tunnel in question and the confidence in traffic conditions expected. Values above ten?per?cent may be encountered for short periods but usually when the NO2 levels are low.CITATION:O’Gorman, S and Gehrke, P, 2014. NO2:NOx ratios in Australian road tunnels, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 95–102 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By L Thorburn

In 2009, the Queensland Government developed a series of amendments to environmental authorities (EAs) for mines throughout the Fitzroy Basin in response to studies that assessed the cumulative impacts of mine water discharges in the basin. One of the key amendments was the requirement for all mines in the Fitzroy Basin to develop and implement a receiving environment monitoring program (REMP). The intent of the REMPs was to provide baseline information on the condition of the receiving environments of the mines and any impacts resulting from release of mine-affected water. Since this time, the requirement to complete a REMP has been incorporated into new or revised EAs for mines (including metalliferous mines) in other regions, as well as for other industries that discharge to natural watercourses (such as coal seam gas). This paper discusses the approaches that can be used to incorporate biological monitoring and direct toxicity assessments into REMPs. It highlights the importance of collecting biological data using sound experimental design principles to investigate whether releases resulted in environmental harm; and the use of monitoring data, coupled with direct toxicity assessments, for setting more realistic, site-specific trigger values and release limits (compared to the default guidelines such as Australian and New Zealand Environment and Conservation Council (ANZECC), which may not be appropriate to the region). Implementation of a robust REMP can maximise outcomes for both the proponents and the environment.CITATION:Thorburn, L, 2013. Receiving environment monitoring programs - making the most out of biological indicators and direct toxicity assessments for monitoring of aquatic ecosystems, in Proceedings Water in Mining 2013 , pp 143-148 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By J Say, M Hawtin, L Carlon, P Cann

Historically, production from sublevels of the Ernest Henry Mine (EHM) started from blind uphole rises at the end of slot drives. Where previous investigations considered removing these slot drives and starting production with independent ore drives, any development savings were consumed when drives were extended to minimise ore loss. Since 2017, EHM and Orica have been investigating opportunities to optimise drill and blast practices by implementing Orica’s Wireless Electronic Blasting System (WEBS). To reduce ore drive development metres, a novel design was proposed utilising the WebGen™ 100 system to combine a rise with pre-charged widening firings. Initially these new rise and widening firings achieved results similar to previous EHM designs, achieving on average 81 per cent of design height and width. Due to poor performance of the fourth trial a significant re-design was required. Modifications included drill hole re-positioning, in-hole primer relocation and initiation delay adjustments. Since the re-design a step change in rise performance has been observed with rise and pre-charged widening shots averaging 95 per cent of design height and width. With rise and widening performance exceeding expectations, the removal of slot drives has allowed a substantial reduction in lateral development. Development savings of 165 m and 169 m from the RL1325 and RL1300 levels have been achieved. Primary draw and ore recovery has also increased due to the later addition of pre charged forward stripping rings. Level design changes have also significantly improved the mining cycle by allowing for a reduction in required ground support, improved secondary ventilation, a reduction of critical path development, simpler production scheduling and less wear and tear on machinery. Future mine level designs now incorporate key learnings and are proving beneficial to a variety of scenarios including changing orebody boundaries at depth.

Mar 15, 2021

By N Cusworth, W R. Mackenzie

"In 2007, the authors presented a framework for the conduct of resource project feasibility studies and provided guidance on minimum standards and best practice (Mackenzie and Cusworth, 2007).This paper will present the authors’ observations in relation to feasibility studies undertaken to support investments made during the unprecedented period of resource project capital investment since 2007. It will also provide comments on general trends in the mining industry’s approach to project assessment and update recommendations on best practice.CITATION:Mackenzie, W R and Cusworth, N, 2016. The use and abuse of feasibility studies – has anything changed?, in Proceedings Project Evaluation 2016, pp 133–148 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016