Search Documents

By Fred D. DeVaney

W. O. Philbrook (Carnegie Institute of Technology, Phila.)—Mr. DeVaney's paper is a valuable addition to the growing technology of the magnetic roasting of lean iron ores. His furnace is ingeniously designed to permit close control of the process and to achieve high thermal efficiency by counter-current heat exchange and the withdrawal of both solid and gaseous products at relatively low temperatures. The principle of using a lean reducing gas to avoid over-reduction of the ore even at high operating temperatures (for rapid re-action rate) is thoroughly sound. The gas analyses and flow rates reported, however, are internally incon- sistent and render suspect any details of a heat balance based upon them. While it is entirely proper to consider the entrant gas as a reagent and to account only for the heat evolved by consuming a portion of the gas, many operators are accustomed to a heat balance using the total calorific value of the reagent supplied; and comparison of heat balances made with different bases of calculation can be quite misleading. Since Mr. DeVaney's paper is likely to be cited frequently in future discussions of magnetic roasting processes, it seems worth while to point out the internal discrepancies and to give alternate values of heat requirements for different bases of calculation.

Jan 1, 1954

By Walter Crafts, C. M. Offenhauer

IN the course of study of the heat-treatment of low-alloy steels, the behavior of alloy carbides at subcritical temperatures was found to vary from that indicated by published investigations. In order to establish the ranges of formation of carbides in low-chromium steels, a series of steels containing up to 0.60 per cent carbon and 7.5 per cent chromium has been investigated with respect to the type of carbide formed after quenching and tempering at subcritical temperatures. The types of carbide formed as products of austenite transformation to pearlitic and pseudomartensitic structures have also been determined. There have been numerous investigations of the carbides in chromium steels and diagrams of the iron-chromium-carbon system.1 Westgren, Phragmén and Negresco2 identified the following carbides in chromium steels: [Cementite Fe3C (containing up to about 15 per cent Cr) Trigonal carbide Cr7C3 (containing up to about 55 per cent Fe) Cubic carbide Cr4C (or Cr23C3) (containing up to about 25 per cent Fe) Orthorhombic carbide . Cr3C2 (containing only a few per cent Fe)] The most complete information on the iron-chromium-carbon system was supplied by Tofaute, Sponheuer and Bennek3 and by Tofaute, Küttner and Büttinghaus.4 By means of dilatometric and microscopic studies, sections of the diagram were established. This diagram showed the presence of the special carbide Cr7Ca in steels containing about 2.5 per cent to 12 per cent chromium in low-carbon steels and from about 5 to 20 per cent chromium in r per cent carbon alloys from A1 to room temperature. The present investigation has shown that a carbide inversion from Fe3C to Cr7Ca occurs in chromium steels containing more than about 1 per cent chromium after hardening and tempering at subcritical temperatures above about 500°C. The type of carbide observed to be more stable in quenched and tempered specimens was also found to be produced by direct austenite transformation in corresponding ranges of temperature and composition. EXPERIMENTAL PROCEDURE The steels used in these experiments were made in magnesia-lined crucibles in high-frequency furnaces and were poured into 2-in. ingots. The ingots were forged into 1-in. round bars, and all heat-treatments were conducted on specimens of this section .size. Sections of the bar stock 8 in. long were hardened in air, oil or water depending on the composition, after heating to a temperature sufficiently high to dissolve the carbides. The low-carbon and low-chromium steels were not entirely martensitic after quenching, and contained some ferrite and pseudomartensite. No pearlite was observed in the microstructures after auenchine. The quenched bars were cut into

Jan 1, 1942

By Peter J. Lean

The introduction oE computer control in the grinding circuit of the New Broken Hill Consolidated Limited concentrator in the early 1970's gave smoother operation at optimum performance. The ore feedrate and water additions to the grinding circuit were controlled to operate each of the ball mill/ rake classifier grinding units at the upper limit of the circulating load while classifier overflow density was maintained to give a product size and pulp density suitable for flotation. An incremental expansion of the concentrator in 1981-82 included the installation of hydrocyclones in closed circuit with three of the four ball mills. Without the rake classifiers in circuit the previous control strategy could not be used and the complex interaction of hydrocyclone performance characteristics when classifying coarse grained sulphide ore resulted in the over-grinding of the lead mineral galena. Testwork aimed at optimising grinding circuit performance recognised the enhanced tendency of higher specific gravity minerals to report to the cyclone underflow. The data has been evaluated on an individual mineral basis and then used to develop a model For grinding circuit control. The development of the model which uses inputs of ore feedrate, metal content of the Feed and slurry density of the cyclone overflow to predict the size of the minerals in the grinding circuit product is described and model predictions are compared with plant performance.

Jan 1, 1984

By H. H. Vogel

THIS paper describes the milling practice and operating results of the recently installed heavy-media separation plant of Barton Mines Corporation, the world's largest producer of garnet. This pioneer application of heavy-media separation (sink-float) processes for the beneficiation of a nonmetallic ore is unique in many respects, the details of which will be apparent from the following presentation. CHARACTERISTICS OF THE ORE The property is on Gore Mountain, 5 miles west of the village of North Creek, New York, and 11 miles by road. The altitude of the mine is approximately 2800 feet. The valuable mineral, garnet, occurs in a surface deposit, the ore body being about ¾ mile long and varying in width from 50 to 300 ft. The garnet, principally almandite, Fe3A12 (Si04)3, occurs in a metamorphic rock of uncertain origin. The gangue mineral is principally hornblende, which constitutes from 40 to 80 per cent of the rock. The remainder of the gangue is divided between plagioclase feldspars and hypersthene, with smaller amounts of biotite, apatite and pyrite. The garnet content of the ore body varies from 5 to 20 per cent of the mass and averages about 10 to 12 per cent. The garnet occurs as crystals, mostly imperfectly developed, known locally as "pockets." These crystals vary in size from a fraction of an inch to a foot or more in diameter. Occasionally crystals have been found up to 30 and 36 in. in diameter but they average 4 to 6 inches. Nearly every crystal of garnet is surrounded by a rim of coarsely crystalline hornblende. The quarry faces are striking in appearance, showing crimson-red garnet crystals with their coal black rims scattered over a grayish black background. The specific gravity of the garnet is 3.8 to 4.1 while that of the hornblende ordinarily is 3.07 to 3.24. Some specimens of very dense hornblende have been found with a specific gravity as high as 3.40. The garnet crystals are laminated in structure, and readily cleave into flat, tabular pieces with sharp, chisel-like edges. Even when crushed to a very fine size, the garnet retains this flat, sharp, slivery grain shape. This characteristic, together with its hardness and toughness, gives it its value as an abrasive. FORMER OPERATIONS Mining operations have been carried on for 60 years. Until 1023, only the oxidized (soft rock) section of the ore body was mined. The oxidation, which affected the garnet only slightly, made possible the removal of the garnet from the rock by hand after it was blasted down, using small hand picks. In 1923 a mill was erected on the property, and was rebuilt and redesigned in 1928. Before the adoption of heavy-media separation, concentration was effected by

Jan 1, 1943

By C. W. Spencer, B. F. Addis, G. H. Bishop, C. A. Steidel

STUDIES of the inter granular attack of metals by liquids have generally been confined to polycrys-talline specimens. This note reports the results of preliminary studies of the penetration of bismuth-rich Ni-Bi liquids into oriented bicrystal specimens of nickel. It is found that isothermal penetration follows a parabolic rate law and shows a definite anisatropy with respect to direction on the grain boundary surface. Nickel bicrystals containing < 100> tilt boundaries were grown using the Czochralski method. Relative misorientation of the parent crystals was controlled to ± 1deg. The boundaries are straight in the growth direction, i.e., the common <100>, and generally straight in the transverse direction, as shown in Fig. 1. The starting material, Inco HPM grade nickel was contained in a recrystallized alumina crucible and maintained under argon. Bicrystals typically contain 30 ppm C, less than 10 ppm S, O, N, and 50 ppm residual metallics, principally iron and silicon. Specimens, as schematically illustrated in Fig. l(c),were cut from bicrystal ingots using a thin water-cooled abrasive wheel. To insure removal of all residual strain, which accelerates the penetration, specimens were round through 600 grit silicon-carbide, chemically polished, and annealed for 4 hr at 1375°C under argon. The procedure described by Cheney et al.1 for exposing specimens to

Jan 1, 1962

By F. L. Grammer

In these day, when anthracite is less extensively used as a blastifurnace fuel than it was a generation ago, and managers endeavor to maintain regular and known ore-mixtures, the " freezing " of tuyeres, cinder-notch or iron-notch is infrequeut; and, consequently, the oil-burner or " kerosene blowpipe "* is seldom employed; and furnace-foremen have, to a considerable degree, forgotten their former cunning and persistency in the use of the drill and sledge. Still, in starting new or abandoned plants with untrained labor, and in running some of our large 100-ft. furnaces, slips, resulting in very cold furnaces, may occur, even under experienced managers. During my superintendence of the Cleveland, O., blast-furnaces, such a misfortune, owing to a dearth of trustworthy foremen, was experienced; and our electrician, Mr. Thomas Martin, proposed to open the tuyeres and cinder-notch by means of the heat of the electric arc. We have heard that the surface-cracks or marks developed in rolling heavy plates have been closed by electric welding, as by a soldering-iron, and also that an electric burner has been employed at some German blast-furnaces; but the experiment was quite novel to us; and I think it constituted one of the first, if not the very first, successful application of this device, for the purpose named, in the United States. †

Jan 1, 1902

By W. D. Forgeng, B. F. Decker

IT has been known for almost a century&apos; that silicon and nitrogen combine when heated to a high temperature. Three nitrides have been reported, SiN, Si3N,, and Si,N, containing 33.3, 40.0 and 42.9 pct nitrogen by weight, respectively. The existence of SisN, is well established but that of Si,N, and SiN is doubtful. The first systematic study of the reaction between silicon and nitrogen was made in 1910 by Weiss and Engelhart" who determined the rate at which silicon absorbed nitrogen at temperatures from 1250°C to

Jan 1, 1959

By E. H. Crabtree

THE heavy-media separation plant at the Central mill of the Eagle-Picher Mining and Smelting Co., near Picher, Okla., was started in February 1939. Since that time twenty-four million tons of lead-zinc ore has been treated in the mill, of which approximately 70 pct has been treated by heavy-media separation. Until January 1945, galena concentrate from the flotation plant was used as the sink-float medium. At that time minus 100-mesh ferrosilicon was substituted for the galena, and its use has been continued. The purpose of this paper is to compare the operating results and the costs of operation of the two media. For the purpose of this comparison the period Jan. 1, 1943, to Jan. 29, 1945, has been taken to represent the operation using galena medium; the period Jan. 29, 1945, to Sept. 1, 1946, to represent the ferrosilicon medium. During the first of &apos;these periods about seven and one-half million tons was milled; during the latter, or ferrosilicon period, more than five million tons was milled. It is believed that these tonnages are large enough to give representative data. FLOWSHEET The Central mill has a capacity of 15,000 tons per day. Briefly, the treatment used consists of crushing the ore through 11/2-in. and wet-screening out the minus 3/16in. portion. The minus 1 1/2 plus 3/16in. washed product is treated by the heavy medium; the minus 3/16-in. product is deslimed and jigged. The heavy-media cone tailing is discarded and the cone .concentrate is recrushed and jigged for the production of a coarse lead concentrate. The cone concentrate, impoverished of lead, is then ground in ball mills and treated by differential flotation. The minus 3/16-in. jig product is similarly treated. HEAVY-MEDIA PLANT The heavy-media cone plant treating the minus 1 ½ plus 3/16-in. product consists of one open-top cone 20 ft in diameter by 20 ft deep, equipped with a central airlift. Concentrate is discharged from the top of the airlift to a 3 by 14-ft low-head Allis-Chalmers drainage screen. Medium drains back into the cone, from the first half of this screen. The last half of the screen is provided with washing sprays for further removal of medium. Cone tailing is similarly drained and washed. Undersize from the washing screen is thickened and then cleaned in the medium-cleaning plant. When galena was used as a medium, cleaning was done in Fagergren and Denver flotation machines. The ferrosilicon is cleaned in three 36-in. and one 24-in. Crockett magnetic separators. A flowsheet of the cone plant is shown in Fig 1.

Jan 1, 1947

By John Henderson

Densities of melts 0f the lime-iron oxide-silica system in contact with solid iron have been measured by the maximum bubble pressure method in the temperature range 1250° to 1440°C and the composition range 0 to 40 mol pct lime, 15 to 100 mol pct iron oxide, and 0 to 55 mol pct silica. Densities range from 4.65 g cm 3 for wustite at 1440°C to 2.75 g cm-&apos; at 1350°C for a melt containing 30 mol pct lime, 20 mol pct iron oxide, and 50 mol pct silica. The results are interpreted in terms of a postulate that the melts can be regarded as a random array of oxygen ions in which regions of local order exist to satisfy the coordination requirements 0.f the cations. An understanding of the nature of metallurgical slags is basic to the development of a sound theoretical description of heavy metallurgical extractive and refining processes. Because these liquids are complex, direct measurements of their properties has not thrown much light on their structure. This has led to the approach of measuring the properties of simpler liquids, and building up their complexity until slag compositions are reached. In this way the density of liquid iron silicates was measured in a previous study1 and the present work represents a further stage in this synthesis. EXPERIMENTAL The technique used in the measurement of density was the maximum bubble pressure method. Details of the apparatus and procedure were similar to those previously reported,&apos; with the exception that a constant voltage transformer was used to supply the power input to the furnace and six silicon carbide resistance elements were used in place of the molybdenum winding. With these modifications melt temperature could be maintained within 1 centigrade degree during the course of a run. The silica used to prepare the melts was washed natural quartz ignited at 1000°C; wustite was prepared by air-melting A.R. grade ferric oxide in an iron crucible and lime was prepared by air ignition, at 1000°C, of weighed quantities of A.R. grade calcium carbonate, previously air-dried at 110°C. The finely ground constituents were intimately mixed in a glass ball mill prior to melting. Temperatures quoted are accurate to * 5°C and the standard deviation of the density values, calculated by the method of least squares, ranged from 0.5 to 1.8 pet. However, replicate determinations of density on different melts of the same nominal composition at the same nominal temperature did not vary by more than 1 pct, Table I, and this figure has been taken as an estimate of the accuracy of the density results. The density of carbon tetra-chloride was also measured as a check on the absolute performance of the experimental method. At 20°C a value of 1.593 * 0.002 g cm"3 was obtained; this compares with the literature value2 of 1.595 g cm"3. Results of experiments designed to measure the dependence of the density of lime-iron oxide-silica melts, in contact with solid iron, on composition and temperature are shown in Table I. Because iron sometimes precipitated in the sample during quenching, the Fe203 chemical analyses were only poorly reproducible and should be taken as a guide rather than as absolute values. Fig. 1 shows the data from various sources for the density of liquid iron silicates and Fig. 2 shows isodensity contours at 1410°C for lime-iron oxide-silica melts, calculated by graphical interpolation of smoothed curves drawn through the experimental results, together with the 1400°C results of Adachi and ogino3 and Pope1 and Esin.4 Fig. 3 shows the isothermal variation with composition of the volume of melt per gram ion of oxygen at 1410°C and Fig. 4 shows regions in which the temperature coefficient of this volume is negative, positive, or negligible (<0.005 cm3 deg-I). DISCUSSION a) Disparity Between Reported Density Results. Consider the system iron oxide-silica, the results for which are summarized in Fig. 1. Although there is some difference in the temperatures at which the various densities apply, this difference is not sufficiently large to account for the observed discrepancies. The reliability of the present results for the low-silica region has been confirmed by measurement of the density of liquid wustite by three different techniques. At 1410°C the density measured by a balanced-column method was 4.55 g cm"3, by a combination balanced-column and gas-densitometer method 4.59 g emd3, and by a pycnometer method 4.53 g cm"3. Schenck, Frohberg, and Hoffermann&apos; have also reported a value of 4.55 g cm"3 for the density of liquid wustite at 1400°C. It must be concluded, therefore, that neither Pope1

Jan 1, 1964

By D. A. Crerar, R. L. P. Kleinmann, R. R. Pacelli

A bacterium, Thiobacillus ferrooxidans, is of prime importance in the formation of acid drainage from pyritic material. Above pH 4.5, T. ferrooxidans increases initial acidification; below pH 4.5, it allows acidification to continue by oxidizing Fe2 +. Below a pH of approximately 2.5, the activity of F3+ is significant and results in steady-state cycling between oxidation of pyrite by Fe3 + and bacterial oxidation of Fe2 +. Laboratory and field tests demonstrate that inhibition of T. ferrooxidans by controlled release of anionic detergents can inexpensively reduce pyrite oxidation and acid formation.

Jan 1, 1982

By N. J. Grant, A. W. Mullendore, Y. Ishida

Creep tests were performed at 500°F on polished specimens of A1-3 pct Cu at stresses of 2000, 4000, and 6000 psi. The effects of the size and distnbution of the second phase were studied in connection with the mechanisms of deformation, especially grain boundary sliding. Although the amount of grain boundary sliding varied considerably for the different heat treatments, yestriction of grain boundary sliding is not due primarily to precipitate on the grain boundary. NUMEROUS prior investigations of grain boundary sliding, notably those of McLean, 1 Rachinger, 2 Rhines, Bond, and Kissel, 3 and Brunner and Grant,4 have established the importance of this phenomenon in the deformation of pure aluminum and its solid-solution alloys at elevated temperatures. An extension of this kind of study to the case of a simple two-phase structure is an important step towards understanding the deformation behavior of more complex alloys. A two-phase A1-3 pct Cu alloy was selected for this study. The creep behavior of alloys in this system has been studied by Sully and Hardy,5 by Underwood, Marsh, and Manning,&apos; and by Pelloux, Chaudhuri, and Grant.7 In these studies, the prior heat treatments were such that some precipitation took place during the tests in most cases. Pelloux, Chaudhuri, and Grant7 studied the creep of A1-2 and 3 pct Cu alloys in the overaged condition. Their results indicated that the structure most effective in promoting high-temperature strength consisted of a fine, closely spaced grain precipitate and large, widely spaced particles on the grain boundary. The present work consists of quantitative meas- urements of grain boundary sliding during creep of an A1-3 pct CU alloy with four different precipitate distributions. The aims were to quantitatively define the role of the second phase on grain boundary sliding, and to obtain information regarding the mechanism of grain boundary sliding. MATERIALS AND PROCEDURE A high-purity A1-3 pct Cu alloy, kindly supplied by Alcoa, was used in this investigation. The composition of the alloy in weight percent was as shown in Table I. This composition is such that A12Cu exists as a second phase at temperatures below 850°F. A homogeneous grain size of 0.6 to 0.8 mm was obtained by annealing the machined test bars for 5 min at 1000°F, furnace cooling to 930°F, and homogenizing for 5 hr. Following the recrystalli-zation and homogenizing anneal, four different heat treatments shown in Fig. 1 were utilized. The F7 and F5 treatments utilize a furnace cool to the aging temperature while Q7 and Q5 have a water quench from the homogenization temperature before aging. Figs. 2 to 5, and Table 11, show the size and shape of precipitate dispersions obtained with the above heat treatments. The heat treatments produce variations in the dispersion both in the grains and along the grain boundaries. Precipitate particles along the grain boundaries are rounded and large (about 1.5 p diameter) in the F5 and F7 structures (Figs. 3 and 5). The grain boundary precipitate was somewhat smaller (0.9 p diameter) in the Q7 structure and no grain boundary precipitate was detected in the Q5 structure using light microscopy. The pre-

Jan 1, 1964

I. THE ENERGY CRISIS STILL EXISTS A. ALTHOUGH IMMEDIATE SHORTAGE IS NOW ALLEVIATED BY: 1. Increased imports through lifting of Arabian embargo; a. Imports were 6.5 million bpd during the week ended January 17, or 1.3 million bpd higher than last year. b. 1.7 million bpd higher than March &apos;74. 2. Decreased demand resulting from higher prices and conservation. a. January 1975 demand was 17.9 million bpd, 0.1 million bpd lower than January 1973 and … b. 2.0 million bpd, or 10% under originally projected demands for January 1975. c. Gasoline (excluding tax) went up 59% from 27d/gal in August 1973 to 43c/gal in September 1974. d. Gasoline demand for January 1975 was 6.3 million bpd, 0.1 million bpd higher than 1973 but 0.7 million bpd ( 10% ) under projected demand. 3. Increased crude and major product inventories. a. January 17, 1975 crude and major product inventory was 794 million bbl, 99 million bbl higher than the same date in 1973. b. 105 million bbl increase since April 12, compared to only 38 million bbl increase during the same period in 1973.

Jan 5, 1975

By E. H. Crabtree

The heavy-media separation plant at the Central mill of the Eagle-Picher Mining and Smelting Co., near Picher, Okla., was started in February 1939. Since that time twenty-four million tons of lead-zinc ore has been treated in the mill, of which approximately 70 pct has been treated by heavy-media separation. Until January 1945, galena concentrate from the flotation plant was used as the sink-float medium. At that time minus 100-mesh ferrosilicon was substituted for the galena, and its use has been continued. The purpose of this paper is to compare the operating results and the costs of operation of the two media. For the purpose of this comparison the period Jan. I, 1943, to Jan. 29, 1945, has been taken to represent the operation using galena medium; the period Jan. 29, 1945, to Sept. I, 1946, to represent the ferrosilicon medium. During the first of these periods about seven and one-half million tons was milled; during the latter, or ferrosilicon period, more than five million tons was milled. It is believed that these tonnages are large enough to give representative data. Flowsheet The Central mill has a capacity of 15,000 tons per day. Briefly, the treatment used consists of crushing the ore through I½- in. and wet-screening out the minus 3/16-in. portion. The minus 136 plus 3/16-in. washed product is treated by the heavy medium; the minus 3/16-in. product is deslimed and jigged. The heavy-media cone tailing is discarded and the cone concentrate is recrushed and jigged for the production of a coarse lead concentrate. The cone concentrate, impoverished of lead, is then ground in ball mills and treated by differential flotation. The minus 3/16-in. jig product is similarly treated. Heavy-media Plant The heavy-media cone plant treating the minus I½ plus 3/16-in. product consists of one open-top cone 20 ft in diameter by 20 ft deep, equipped with a central airlift. Concentrate is discharged from the top of the airlift to a 3 by 14-ft low-head Allis-Chalmers drainage screen. Medium drains back into the cone, from the first half of this screen. The last half of the screen is provided with washing sprays for further removal of medium. Cone tailing is similarly drained and washed. Undersize from the washing screen is thickened and then cleaned in the medium-cleaning plant. When galena was used as a medium, cleaning was done in Fagergren and Denver flotation machines. The ferrosilicon is cleaned in three 36-in. and one 24-in. Crockett magnetic separators. A flowsheet of the cone plant is shown in Fig I.

Jan 1, 1949

By Lawrence H. Van Vlack

DISCUSSION, H. L. Burghoff presiding C. S. Smith (University of Chicago, Chicago)—The author is to be congratulated on his valuable contribution to the extremely meager absolute data on interface energies in metallic systems. It is interesting to note that the ratio between a and r iron boundary energies is approximately the same in the quaternary alloy with silicon, carbon, and sulphur as in the binary Cu-Fe alloy. A value for the copper grain boundary energy can be obtained from the author&apos;s data, Tables IV and VI, by utilizing the energy ratios of the following pairs of interfaces: copper-sulphide/copper, copper y iron, y iron/y iron, y iron/ copper, and copper/copper. This gives a value of 595 erg per sq cm for the free energy of the copper grain boundary. Despite this circuitous route and the assumption that the y iron boundary is identical in alloys with and without sulphur and does not change between 1105" and 100O°C, this figure is in remarkably close agreement with other values of the copper boundary energy, obtained by equilibration against lead and against the free copper surface. It therefore appears either that impurities do not greatly affect the grain boundary energies or that boundaries in even nominally pure metals are already sufficiently contaminated so that further change has little effect.

Jan 1, 1952

By Roberto Pimentel de Souza, Helder Zenóbio

VRD started producing pellets in 1969 with one 2-million-t straight grate plant. In the beginning of April 1973, the second unit came on stream with an additional capacity of 3 million t/a of pellets. In January 1977, the third unit started, bringing the annual capacity to 8 million t/a. In the coming year (1978-79), three more units, 3 million t each, are expected to begin production. CVRD&apos;s experience with different binders and additives is described. Over the years several kinds of pellets have been produced to satisfy market requirements. General quality information is given for each.

Jan 1, 1981

By Robert Bakish

VARIOUS aspects of structure-sensitive corrosion of single crystals and polycrystalline aggregates of Cu,Au have been presented in papers by the author, in association with W. D. Robertson. Prompted by some observations in the course of these studies, a new approach to the problem was undertaken. Results of these new experiments are reported here. Thin slices, less than 2 mm thick, were prepared from single crystals 3.5 mm in diam grown by the Bridgman technique. The crystals were homogen- ized for 300 hr at 850°C. Crystals with no deformation, crystals deformed in tension to the yield point, and crystals deformed 20 pct in excess of the yield point were used. Crystals of several different orientations were studied. Slices were immersed for one month in 2 pct aqueous solution of FeCl3 and, subsequent to this immersion, were subjected to bending. Immersion and bending were carried out at room temperature. The size and geometry of the crystals did not permit accurate data on the loads involved. A most unexpected result was obtained in the process of bending these slices of Cu3Au crystals normal to the (110) plane. Completely brittle be-

Jan 1, 1958

By H. C. Fiedler

It was recently shown with 3.3 pct Si-Fe containing 0.026 pct S and 0.06 pct Mn that the extent of secondary recrystallization to a cube-on-edge texture is determined by the cooling rate from the solution temperature of the manganese sulfide inclusions.1 With a rapid cooling rate, many small inclusions rather than a few large ones are formed, which leads to increased restraint to normal grain growth and more complete secondary recrystalliza-tion. Strip samples 12 mils thick, rolled from 1-in.-thick slabs that were cooled at 130°C per min

Jan 1, 1964

By Arthur Mitchell

POSSIBLY in no other of the non-ferrous mining districts of this country has the use and develop-ment of mechanical loaders been carried to such an extent as in the "lead belt" of Southeast Missouri. It has become apparent to the four mining companies in the district that it is imperative to apply satisfactory mechanical methods to the chief remaining stage of the entire operations-mining, milling, smelting and refining-in which manual labor is still largely used to handle material in process. With increasing wages and with the reduction of the metal divisor by the extension of mining into lower-grade orebodies, the shoveling cost per ton of lead produced has become relatively so large that in an effort to reduce it there is ample justification for considerable capital expenditure. Hand shovelers load about 18 tons of ore per shift and the average grade is less than five per cent. lead. Further, the ore is relatively heavy, about 21 cu. ft. to the ton when broken, and is often so coarse and so closely compacted after shooting that it requires much more block-holing, sledging, and muscular effort to shovel than, for example, does the cherty and more granular ore of the Joplin district or the finer ore in the headings of a drift mine. No mining company desires to pay for mere back muscles if it be economically feasible to avoid it, and labor saving machinery should be susceptible of operation by older employees, who are no longer capable of the more strenuous manual occupations.

Jan 4, 1923

By C. J. McHargue

THE angles between the crystallographic planes in cubic crystals have been given by Bozorth,¹ in magnesium, zinc, and cadmium by Salkovitz,² and in tin by Nicholas. The determination of the orientation of single crystals and the study of plastic deformation require the knowledge of these angles and are often facilitated by use of a standard projection. Tables of these angles and standard projections have not been published for titanium or zirconium which have c/a ratios considerably less than those hexagonal metals for which this data is available. Accordingly, Table I has been prepared giving these angles. Fig. 1 presents a standard (0001) projection of titanium. The angle between (h1k1i1l1) and (h2k2i2l2) was calculated by means of the formula: h1h2 + K1K2 + 1/2 (h1k2 + h2k1 + cos 4 = [(hi2 + K + h1k1 + 3/4 l12 (h2² + C" a² 3/4 — l1 l2 C² k2²+ h2k2 + 3/4 —l2²) ] 1/2 c² The c/a ratio for titanium is taken from the data

Jan 1, 1953

Organization Place Date 1917 Mine Inspectors Institute of U. S. A Indianapolis, Ind. July 9-11 American Society of Sanitary Engineers Grand Rapids, Mich. Aug. 1-3 National Association of Stationary Engineers... Evansville, Ind. Sept. 10-15 National Exposition of Safety and Sanitation.. New York City Sept. 10-15 American Iron, Steel & Electrical Engineers.... Philadelphia, Pa. Sept. 10-14 American Institute of Metals Boston, Mass. Sept. 24-29 American Foundrymen&apos;s Association Boston, Mass. Sept. 24-29 Chemical Industries, Third National Exhibition. New York City Sept. 24-29 American Electro-Chemical Society Pittsburgh, Pa. Oct. 3-6

Jan 7, 1917