Search Documents

By R. C. Buehl, M. B. Royer

High manganese slags of low phosphorus and iron content are produced by air oxidation of high phosphorus spiegeleisen in a basic-lined converter. Control of phosphorus and iron within specification limits for ferromanganese ore feed is obtained by a unique cyclic operating procedure. Various types of slags, or synthetic manganese ore, can be made. AN affiliated paper' describes the production of high phosphorus spiegeleisen containing 14 to 23 pct Mn and up to 4 pct P in an experimental blast furnace from open-hearth slag or manganiferous iron ore. This phosphorus content is too high for use of the spiegel in normal steel-production operations. Consequently, a preferential separation must be effected whereby the manganese is concentrated in a product that is usable in industrial operations. The preferential separation methods being investigated for this phase of the work are confined to pyrometal-lurgical processes for ready incorporation into steel-plant operations. It is fortunate that manganese is more actively oxidizable than iron or phosphorus, and therein lies a preferential separation method for isolating manganese from these two elements. Silicon is more strongly oxidizable than manganese, and its oxidation precedes, or occurs simultaneously, with manganese. Therefore, manganese and silicon are separable into a high manganese oxide slag phase while the phosphorus and iron remain in the molten metallic state. Complete separation of these elements represents an ideal condition which is not generally attainable in actual operations. This pyro-metallurgical method for separating manganese from phosphorus and iron by preferential oxidation was investigated by blowing 500 lb of metal in a basic-lined vessel to obtain preliminary information on the effectiveness of the procedure. Certain conditions of attainment in the separation process are desirable in any method for removing manganese from high phosphorus spiegeleisen, such as: 1—High recovery of manganese in the oxidation product; 2—the product to be of equal or better quality than ferromanganese-grade ore—48 pct Mn minimum, less than 10 pct SiO2, and Mn-P ratio of 300:1; and 3—attainment of the enumerated objectives in a product amenable to industrial handling, such as a slag of high manganese content that will flow from the processing vessel and of sufficient fluidity for ready separation of metallic granules that may have become mixed with the manganese slag phase. Previous Work Recovery of manganese from low grade ores and industrial byproduct slags by smelting to spiegeleisen, with subsequent oxidation to synthetic ferro-manganese-feed ores, has been a subject for periodic investigation during the past four or five decades in the United States and Germany. Joseph' and associates of the Bureau of Mines North Central Experiment Station, Minneapolis, Minn., smelted manganiferous iron ores of the Cuyuna range, Minn., to spiegeleisen and subsequently tried air and ore oxidation procedures for concentrating the manganese into synthetic ferrograde manganese ore. Joseph's results on the operation of a side-blown basic-lined converter for air oxidation of manganese from molten spiegeleisen were so discouraging that the procedure was abandoned after 11 blowing tests. Much slag was thrown from the converter vessel; phosphorus content was four to five times the maximum allowable for ferro ore; and a manganese-iron ratio of only 2 or 3:1 was obtained in the slag instead of the required 8:1. Oxidation of manganese from spiegeleisen with about 0.5 pct P, by adding iron ore to molten spiegel in an experimental open-hearth furnace, proved moderately successful in Joseph's experiments. The main drawback to the operation was the necessity for over-oreing for effective oxidation of the manganese with consequent too high iron oxide residual in the slag. Furthermore, the phosphorus content was proportional to the iron concentration and therefore much too high, so that several hours of reduction by a carbonaceous material were required to adjust the iron and phosphorus to the desired content of high grade ferro feed. A troublesome feature of the slag product of the spiegel oxidation process was its lack of fluidity if the silica content was less than 10 pct, the concentration considered desirable for the synthetic ore. Approximately twice the desired concentration of silica was required to impart enough fluidity for transfer from the vessel by pouring. The acute shortage of manganese in Germany

Jan 1, 1953

By W. Denham Verschoyle

IN designing a pocket instrument whereby any given horizontal or vertical angle may be closely approximated, the following points should be kept in view, if general utility is aimed at 1. The instrument should be light and compact, so that it can be carried in the pocket, or in a sling. 2. It should be capable of observing any angle whatever, horizontal or vertical. 3. Since time is often an important consideration in making a preliminary survey, it should be capable of giving the horizontal and vertical angle at one observation. I do not know of any instrument that will fulfill these requirements, except the one here described. Where the depression- or elevation-angle of the distant object, whose bearing is required, exceeds 50 or 60 degrees, it becomes difficult or impossible with a prismatic compass, for instance, to obtain accurate results; and since it frequently happens, particularly in mining, that much work requires to be done beyond that limit, it is obvious that an instrument which can be used to observe a high angle just as easily as a low one, if not absolutely a necessity, will at least be a great convenience. How this " pocket transit " attains to the required degree of universality will be understood from the diagram, Fig. 1, in which B is a beveled, graduated circle, attached to and freely revolving about the center of the magnet A. Light falling on B is reflected through a window in F (the compass-box), along the line AC, and is again reflected back to the eye at D by the prism C. By a simple arrangement, the sight-line DCE can be completely revolved in the vertical plane DE, which is normal to AC. It is clear, then, that no matter through what vertical

Jul 1, 1907

By Mark R. Lamb

THE various methods of treating pulp in air-agitation tanks offer problems for experiment and study which are fascinating as well as practical. The usual method heretofore has been to fill each tank in turn, agitate the mixture the required period and then discharge the treated pulp into a storage-tank, from which it. is drawn to the filter as required. A later method is to run the pulp from the tube-mill, classifier, thickener, or settler into the first of a set of tanks, and thence continuously or in series through the remaining tanks, finally drawing off the pulp to a continuous filter, or to a pulp-storage tank if the filter is of the intermittent type. It is this method which I propose to discuss here in a preliminary way, with the idea of going exhaustively into the examination of the results of a series of experiments in a later paper. It may be of interest to note that the design of a cyanide-plant has recently been completed in which the estimated cost of the agitation-tanks, storage-tanks, and pumps was 30 per cent higher for the charge-agitation arrangement than for the series plan. The first question in studying the series method is, "What is the actual period of treatment undergone by the pulp?? One first supposes that by chance some of the pulp may get through with little or no treatment, while other portions may stay in the tanks a needlessly long period. The former is not probable or even possible, and the latter is, practically, true to only a limited extent. The greater the number of tanks the greater is the percentage of chance that all the pulp will be treated equally. Without going into the mathematical analysis of the problem (which is of little value, since it is based on problematical premises), its important terms may be clearly grasped by thinking of, or " visualizing," the conditions when,

Jan 1, 1910

By H. L. Sauder, J. L. Newman, C. Waddell

An instrument capable of measuring subsurface flow rates is described. The instrument is self-contained and may be run on piano wire line. It detects flow by means of an impeller suspended between two torsion wires. The force of the well fluid striking the impeller causes the impeller to rotate, exerting a torsional force to the wires. This force is determined by recording the angle of rotation of the impeller on film using a battery-driven, clock-controlled camera. The impeller is sensitive to flow in either direction and the same instrument can be used to measure injection as well as production rates. Changes in direction of flow, such as might be caused by thief zones, are measurable and are indicated by a reversal of the direction of rotation of the impeller. Adjustment of the sensitivity of the instrument to measure a wide range of flow rates is accomplished by the use of different size torsion wires. An umbrella-type fluid trap, which contacts the casing or wellbore, diverts the flow through the flow tube. The fluid trap remains closed while rurrning in the hole and can be opened at any point in the well. The instrument with the trap closed is 1 3/4 in. OD and may be run through 2 in. tubing. Successful flow profiles have been made on wells with flow rates ranging from 60 BID to 4,000 B/D at surface pressure up to 4,500 psi. The instrument is designed for high-pressure and high-temperature operations. INTRODUCTION The need for an instrument that will measure flow rates in a wellbore is as old as reservoir engineering itself. A number of such devices have been designed within the past few years. Some of these have been described in the literature1,2,3,4,5,6 One of these devices1. a hot-wire anemometer type, made many successful jobs in dry gas producing areas. Difficulty was encountered when this flowmeter was used in wells producing liquids and development work was initiated to overcome this difficulty. The present flowmeter is the result of this work and provides an instrument with a wider range of application in the industry. Consider- able development work has been done on the tool involving many changes in the mechanics of recording the flow readings, however, the basic principle of flow detection has remained the same since its inception. PRINCIPLE OF OPERATION The basic principle of operation of the flowmeter is the utilization of a portion of the kinetic energy of flowing well fluid to impart a rotational force to an impeller suspended between two torsion wires. This impeller, Fig. 1, is a screw-type propeller with the blades having a pitch angle of 40. As the well fluid passes through the instrument it strikes the impeller. The resulting force rotates the impeller and twist\ the torsion wires to a balance point at which the torque imparted to the wires balances the force required for the impeller to deflect the well fluid. The impeller is symmetrical and a change in direction of the flow results in a reversal of the direction in which the impeller is deflected. Thus the direction of the flow as well as its velocity is indicated. A dial is attached to the impeller by means of a hollow tube through which the upper torsion wire extends. The angular position of the impeller is recorded by photographing the dial at frequent intervals. In any given set of torsion wires the modulus of shear and polar moment of inertia remain constant and the deflection varies directly with the applied torque. The deflection imparted to the torsion wires also varies as the square of the fluid velocity. Further, the velocities represented by any two given deflections hear the following relationships: and Where V = velocity of flow stream and O ;= deflection. This is the basic relationship which is used to calculate the relative velocities represented by a given set of deflections where the velocity represented by any one of the deflection readings is a known quantity. For a given torque, the deflection of the torsion wire varies inversely as the fourth power of the wire diameter. Wire sizes ranging from ,005 in. in diameter to .022 in. in diameter can be used. The range of

Jan 1, 1957

By George A. Hill

WE of the oil industry, devoted to freedom of initiative, free competitive enter- prise, and free American institutions, applaud, with one voice, affirmation by the President of the national will and purpose to preserve and to protect, against all aggressors, "our American way of life with our individual and national freedom." We subscribe utterly and completely to this guiding declaration and seek its further definition as applied to the oil industry. Fortunately for all, the policy of the Government, after adequate study and deliberation, has been given precise definition. The National Defense Advisory Commission, with its patriotic, highly qualified, and distinguished personnel, has unanimously agreed to and adopted twelve general principles governing national defense contracts and also fair labor standard requirements. The President of the

Jan 1, 1940

By N. A. Ziegler

THE chief difficulty in determining oxygen in steels is its tendency to form a variety of compounds. Almost every element, found as an ingredient in steels, maybe expected to be present as an oxide. Some of these oxides have widely differing properties, and consequently behave differently when attempts are made to reduce them by the vacuum fusion method. As I pointed out in a paper published in the Transactions of the A.S.S.T., Vol. 20, No. 1, many experimenters are spending considerable time and effort in attempting to deter¬mine the degree of completeness of the above reactions, and hold different opinions on the matter. In studying this subject the following table, taken from Hodgman and Lange's "Handbook of Chemistry and Physics" may be used as a guide.

Jan 1, 1933

By R. J. Quigg, G. S. Doble

Commercial stress -relieved TD Nickel bar was shown to retain room- and elevated-temperature tensile strength after exposure up to 2501°F. Cold swaging increased both room -temperature and 2000°F tensile strength. After annealing at 2500°F the strengthening due to swaging was retained at 2000°F hilt eliminated at room temperature. Annealing produced changes in hardness and X-ray half peak width indicating the presence of recovery processes as 1071° as 1000°F but no recrystallization of swaged material was noted at any temperature. In contrast to swaging, rolling induced a recrystal-lized structure after annealing. The tensile strength of this recrystallized structure was comparable to the cold-worked condition. High-temperature tensile properties of as -received bar were highly anisotropic with the transverse tensile strength being one fifth the longitudinal value. The aniso-/ropy is affected by working direction and may he partially reversed by changing the direction of metal flow. The divergence in tensile strength, beginning above 550°F or- approximate one third the absolute melting point, is strain-rate dependent. T D Nickel is a commercial dispersion-hardened alloy containing 2 vol pct thoria. The dispersion, consisting of spherical particles 0.030 to 0.050 in diameter with an interparticle spacing of less than 1 is reported to maintain stable properties up to 2400°F.1 This stability of second phase results in maintenance of elevated-temperature strength at higher temperatures and longer times than normal nickel-base superalloys.2 The purpose of this paper is to describe the effect of various mechanical working operations on the strength and microstructural stability of TD Nickel bar. MATERIAL AND PROCEDURES All material used in this study was commercial TD Nickel bar. This material is produced by a chemical process which results in a nickel powder containing a dispersion of thoria particles. The powder is then pressed, sintered, extruded, and subsequently worked to bar stock. Three starting materials from three separate lots were used: as-extruded bar. 1-in.-diam stress-relieved bar, and 1/2-in.-diam stress-relieved bar. Since TD Nickel bar stock is cold-worked without a recrystalliza-tion anneal, the accumulated deformation or degree of cold work in these materials increases as the bar diameter decreases. Some of the 1/2-in.-diam bar was swaged to 1/4 in. diameter at room temperature in order to produce an as-worked condition for comparison with the stress-relieved stock. Tensile testing was performed on an Instron Tensile Tester at a constant crosshead speed of 0.020 in. per min. The 0.2 pct offset yield strength was measured from the load-crosshead movement plot. Specimen gage dimensions were 0.080 in. in diameter by 0.40 in. in length, producing a strain rate of approximately 0.050 min-1. Specimens were tested in air and heated within a resistance-wound furnace controlled to ±5°F. A 15-min soak at temperature was employed before testing. Samples were heat-treated in air and specimens machined after exposure with sufficient material removed to eliminate any surface contamination. X-ray line breadth was determined from a diffractometer scan of a transverse face of a bar using copper K, radiation. Metallographic preparation utilized standard mechanical polishing with Carapella's etch. Specimens for electron microscopy were electropolished in a 1:7 sulfuric/methaol solution and chromium-shadowed collodion replicas prepared. RESULTS AND DISCUSSION I) Effect of Elevated-Temperature Exposure on the properties of TD Nickel. The effect of various elevated-temperature exposures on the room-temperature tensile strength of TD Nickel is shown in Table I. In the unexposed condition the tensile strength, reduction in area, and hardness all increase with increasing accumulated deformation while the elongation decreases. After exposure at 2500°F the strength of all three materials decreases to about 65,000 psi and the elongations increase slightly. The apparent increase in strength of the 1-in. bar after a 2000°F treatment is probably experimental scatter. These results indicate that the room-temperature strengthening due to additional deformation is annealed out upon elevated-temperature exposure. In contrast to the room-temperature data, the 2000°F tensile strengths increase in order of increasing deformation even after exposure. Although some loss of strength occurs after exposure, much of the effect of working is still maintained at 2000°F. The room-temperature hardness after various

Jan 1, 1965

By H. J. Donnell, B. C. Parks, O&apos

In 1930 the late Dr. Reinhardt Thiessen set up a method of microscopic analysis and type classification of coal that has since been followed as standard practice in the coal-petrography laboratory of the Bureau of Mines. Thiessen's terminology which designated the constituent parts of coal in terms of botanical origin was introduced in 1920.1 The technique, however, of preparing a completely representative series of thin sections from a column sample of coal for use in making quantitative determinations of coal components with a microscope was developed about 10 years later by Thiessen and coworkers G. C. Sprunk and H. J. O'Donnell.2 Complete thin-section analyses subsequently have been made of 126 column samples of various ranks and types of American coals. The data and information were assembled from these thin-section studies and published in a large number of reports dealing chiefly with investigations of the coking and hydrogena-tion properties of certain American coals. In the years following adoption of Thies-sen's method, a considerable amount of work was done in collecting column samples of many coals, making routine thin-section analyses of these, interpreting the results, and finding practical application for the information in other fields of coal research. The many reports and papers covering the work in coal petrography, however, offer very little discussion that can be considered as critical appraisal of the technique. Criticism outside the Bureau most often has voiced questioning opinions concerning the accuracy of the method used of measuring coal components microscopically and classifying the coal into arbitrary types on the basis of the quantitative determinations. The principal purpose of this paper is to discuss in some detail and present data showing the results of certain investigative work done in the petrography laboratory on the accuracy of the Bureau's method of microscopic measurement of components in coal thin sections. Data from microscopic analyses on file made by G. C. Sprunk and H. J. O'Donnell were freely used in the investigation, and a table of columnar analyses from an unpublished manuscript by Sprunk is included in this paper for reference. In the course of the experimental work a method was developed for measuring in-strumentally with a planimeter the components shown in micrographs of selected thin sections. Measuring coal components with a planimeter furnished useful information for studying the accuracy of microscopically measuring the same components in thin sections. Petrographic Components and Type Classification of Coal Thiessen considered coal to be composed of two visibly different major components present in various types of coal in greatly varying proportions. He named

Jan 1, 1949

By H. A. Hoffman

Competition from an all-flotation plant, with demonstrated economies and efficiencies, plus a change in smelting contract and introduction of improved cyclones lead to conversion from gravity-flotation. Detailed descriptions are given of equipment installed and procedures used at St. Joseph Lead's Federal mill. Future plans include further quality control by instrumentation in all aspects of the mill operation. Also planned are improvements in materials handling systems. Competitive conditions will continue to dictate improvements and changes in the mill flowsheet. The advent of all-flotation mills in the Lead Belt was introduced by the Indian Creek mill in late 1953. This modern and efficient plant then became a pattern for the other mills in this area to re-evaluate their circuits in an effort to develop flowsheets that would improve operating conditions and metallurgy. The Indian Creek mill demonstrated that all-flotation would require considerably less operating and maintenance labor than the combination of tabling and flotation that was common in the Lead Belt at that time. Two significant changes occurred in recent years to allow all-flotation to be seriously considered in other Lead Belt mills. One was a change in the smelting contract which did not require gravity concentrate. Another was the development of cyclones which provided classification of the flotation feed in a very small space. Since the Federal mill was the largest concentrating plant in the Lead Belt it was felt that the greatest savings could be made by investigating the all-flotation possibilities at this mill. Interest was stimulated by the milling and ore dressing Depts. to determine if this mill would be converted without undue cost, provided the metallurgy could be improved. Accordingly, laboratory tests were initiated to learn what metallurgical benefit could be derived. Numerous tests were run which indicated that grinding to all-flotation would improve the tailing by as much as 0.02 pct Pb. This was quite significant when multiplied by the tonnage of ore treated. Projecting the added cost of power for extra grinding and flotation, and the additional flotation reagents required, plus additional new equipment that would have to be purchased, it would still add up to a considerable saving. The all-flotation mill would reduce man power by some 30 pct, and make a metallurgical improvement. Operating costs could be reduced bv 2$ per ton. The metallurgical improvement would amount to 4$ per ton, for a total of 6$ per ton of ore milled. An estimate of the cost of the conversion was set at $250,000. With the savings as estimated this could be paid off in about two years. On paper it therefore seemed attractive enough to justify a mill test. MILL TESTING One section of the Federal mill was made available for use as a separate test circuit. Cyclones and density controllers were borrowed from the Viburnum and Indian Creek mills. Denver flotation cells were obtained from the Desloge mill that was then shut down. Two 10-cell groups of Fagergren flotation machines, consisting of eight roughers and two cleaners in each bank, were segregated from the remainder of the plant. The 9x12-ft rod mill was continued as a primary grinding mill. The two 6%x12-ft mills on this section were converted from rods to balls, and the speed increased to 22.0 rpm. Cyclones were installed to close the circuit of these ball mills. The ground pulp from each of the ball mills was fed separately to its own bank of flotation cells so that two completely separated test circuits could be run in parallel. This test circuit operated on a three-shift basis from Dec. 22, 1959 to Mar. 21, 1960. The first few weeks were occupied in developing conditions for proper metallurgy and trouble-free operations. Results were rather erratic but as the ore dressing laboratory and the mill operators became more familiar with conditions they were able to obtain expected results, which could be duplicated day after day. The last five weeks of testing indicated the best results and are tabulated in Table I. During the first two weeks a Denver unit cell was used on No. 1 flotation circuit. Even though it recovered almost one half of

Jan 1, 1962

By O. Jay Myers

THE war effort has furnished the necessary impetus for better magnesium foundry practice. Four or five years ago, there were but a few formulas in general use for cores and mixtures for magnesium castings. Certain sands, binders, and inhibitors were specified and the proportions of these materials in each mixture were maintained between very narrow limits. As more and more war industries entered the field, much research was carried out and methods and practices were improved. Magnesium founding is still in a state of flux; therefore it is not uncommon to find one foundry spraying inhibitors on its cores, and another foundry using sand mixtures with incorporated protective agents. The basic core or dry-sand mold mixture for magnesium in use today is compounded with sand, core oil or resin binder, cereal, and moisture. Core oil or resin binder are added for baked strength while the cereal binder and moisture are for green strength. The normal mixtures (based on the weight of the sand) contain from 0.5 to 1.5 per cent of both cereal binder and core oil, and the moisture content varies between 1.5 and 5 per cent. The ratio of core oil to cereal binder varies from 60:40 to 40:60, while the correct amount of moisture depends upon the method of coremaking. PROTECTIVE AGENTS In all magnesium practice, protective agents are used in conjunction with the core and molding sands to prevent oxidation of the metal. The use of these inhibitors is not novel, but publications covering this field are not entirely adequate. Beck1 says Magnesium alloys decompose water to form magnesium oxide, hydrogen being liberated in the process (Mg + H20 -+ H21 + MgO). This reaction results in the blackening of the skin and the appearance of areas of porosity on the casting surface, the cavities of which are filled with a grey oxide powder (these are termed `burns'). Although sand cores for magnesium castings are thoroughly dried during the baking cycle, burning will take place on the castings unless the metal is protected properly. This type of burning is more difficult to define than the "water-magnesium" reaction cited by Beck. A possible explanation may lie in the following equation: 2Mg + 02 -s 2MgO Here, the source of the oxygen is not water, but the air in the mold cavity, together with the chemically combined oxygen in the core-binding media. Generally, two methods are used to prevent this reaction from taking place.

Jan 1, 1945

By AIME AIME

TWENTY-TWO sections and all four of the divisions sent delegates to the annual meeting. They became so interested in the wide ranging dis6ussion of old and yet ever-new problems of Institute affairs that three instead of two sessions scheduled were necessary. Monday morning the meeting assembled with President Bassett presiding in the absence of President-elect Tally, who had been called to Baltimore by the serious illness of a brother. Thursday morning Vice-president Turner presided until Mr. Tally appeared after which the latter guided the sessions. Since reports from all of the active sections save one had been mimeographed and sent in advance to the delegates, detailed reports from each were dispensed with. The discussions dealt largely with membership problems, both local and national, with financing, speakers and programs, visits from national officers, and the conduct of the annual meeting. Many interesting and constructive suggestions were made and will be reported back to the sections by the delegates.

Jan 1, 1931

By Philip S. Morse

THE Australian lead-smelting plants began to use charges carrying high zinc percentages somewhat earlier than was common with American plants. When lead smelting first started in Australia the immense deposits of oxidized lead at Broken Hill were available but later these oxidized ores became exhausted and were replaced by sulfides. This was before the days of flotation and these sulfides when concentrated carried about 1 per cent. of zinc to 6 per cent. of lead. The works of the Sulphide Corpn. at Cockle Creek was perhaps the pioneer in high-zinc slags but the Port Pirie plant of the Proprietary Co. was a close and very able second and has continued the work to the present time. The Cockle Creek lead furnaces remained in operation until shortly after the war when most of the Broken Hill companies combined and took over the Port Pirie plant to treat their concentrates. As it was the practice both at Cockle Creek and Port Pirie to carry 20 per cent. or more of lead on the charge, it was found that under these conditions of large amounts of zinc in the charge, good roasting was absolutely necessary and matte production was unwise. The Hunting-ton-Heberlein system of roasting was introduced and later the Dwight & Lloyd process. In this way, by roasting the sulfide portions of the charge as thoroughly as possible and making no matte, a method of smelting was developed where the slag over long periods carried as high as 20 per cent. ZnO without serious furnace troubles, and slags carrying even up to 33 per cent. ZnO have been reported. The zinc slags were not very different in appearance from the ordinary slags produced in American practice except that they gave off more smoke and fume on tapping. The slag usually ran hot and freely, coming from the tap in a full stream. Normally there was little crust on the sides of the furnace and the tuyeres gave no trouble though they were always rather dark. At the works of the Sulphide Corpn. it was the custom, on account of the labor situation, to shut down the furnaces during the Christmas holidays, thus giving a campaign of about 12 months. The furnaces at the end of the run usually showed no crust on the sides, though crusts always occurred at the back and front ends. A furnace campaign of 22 to 23 months has been made at this plant where both sides of the

Jan 1, 1929

By M. R. Tek

A new method for correlating the data on multiphase flow through vertical pipe is presented. The correlation is based on a "two-phase f factor" concept which was developed and successfully applied to horizontal multiphase flow by Bertuzzi, Tek and Poettmann. Field data previously published on several flowing and gas-lift wells have been used as the basis for the developed correlation. The application of the method to actual two-phase flow problems indicate that this method is capable of predicting the pressure distribution in vertical multiphase flow strings well within the accuracy range usually desired for common engineering and design calculations. A new working chart developed for calculation of two-phase pressure gradients and a graphical step-by-step procedure for the computation of pressure distribution are presented along with an example problem. INTRODUCTION Multiphase flow through vertical pipe is encountered in many engineering installations. In petroleum, chemical process, nuclear engineering and many other industries, problems associated with simultaneous flow of two or more phases through vertical pipe have been of interest for a long time. This interest has increased considerably during recent years due to applications to new processes in petroleum production and refining and to problems of steam generation and heat removal from nuclear reactors. One prominent example of vertical two-phase flow is provided by the gas-lift process where oil, water and gas flow simultaneously. If the pressure profile in a gas-lift well can be predicted within reasonable accuracy, it would be possible to get good estimates of the power required to lift the oil, the optimum depth, the pressure and the rate at which to inject gas. Furthermore, the effect of production rate and tubing sizes on these quantities can be evaluated before any design decision is made on the installation and operation of the flow string. The majority of experimental work available in the literature deals with two-component systems where individual phase flow rates in and out of the pipe remain constant. The general problem of prediction of pressure drops in multiphase flow systems is very complicated. The co-existence of numerous flow patterns of widely different geometry and mechanism, conditions of surface instability and the nature of force fields acting upon the system are among the major difficulties commonly encountered. The classical approach of fluid dynamics which would be based upon the formulation and solution of Navier-Stokes equations has been found by many investigators completely devoid of any hope of success-—not only because of inherent nonlinearities but also because of insurmountable analytical difficulties standirng in the way of setting up the boundary conditions. The presence and effect of interfacial forces on mu1tiphase flow systems further complicate the theoretical approach. For these reasons, many investigators choose to adopt semi-empirical if not purely empirical approaches in order to obtain solutions of engineering utility. A prominent practical solution has been given by Poettmann and Carpenter' in the form of an empirical correlation. In their paper, total flowing densities of fluids and solubility effects of gas in oil have been taken into account for the correlation of field data covering a wide range of operating conditions for oil wells. They treated the gas. oil and water as a single phase of combined propcrties and correlated the multiphase friction factor as a function of the product (pvd), i.e., density X velocity X diameter of the flow string. However, because the product (pvd) is dimensional while the frictior factor is dimensionless, the generality of their result's is somewhat restricted. It seems that the omission 01 viscosity effect may be one of the reasons for the scatter of data as shown in their correlation chart. The concepts of the "two-phase f factor" and the "two-phase Reynolds' number function" were recently developed and successfully applied to correlate horizontal multphase flow by Bertuzzi, Tek and Poettmann.' Recently, two new methods of correlation by Tek and Chan' have been presented on simultaneous flow of liquid and gas through vertical pipe. These two methods of correlation and the working equations in field units necessary for their application are included in this paper. The extension of the conccpt of two-phasc Reynolds' number function successfully developed for horizontal flow into vertical multiphase flow systems, development and evaluation of working charts permitting calculation of two-phase pressure gradients and

By W. L. Hill, W. H. Armiger, S. D. Gooch

The physical properties, chemical behavior under thermal treatment, and fertilizer value of fluorine-containing pseudowavellite (hydrous calcium aluminum phosphate) that occurs as phosphate clay admixed with quartz sand in an extensive deposit near Bartow, Fla., were determined by experiments in laboratory, pilot-plant, and greenhouse. When the mineral was heated at 500°C, 80 pct of the phosphorus become citrate soluble. The heated product, however, deteriorates markedly under moist conditions such as obtain in the soil. EXTENSIVE beds of a soft aluminiferous phosphate lie in the Bartow-Pembroke region of Florida. Although the extent of the deposit is unknown, it is thought that the equivalent of at least five million tons of material containing 25 pct P,Os exists on one large mine property alone, and soft phosphates similar in nature are known to occur elsewhere in the state. This aluminum phosphate, unlike fluorapatite, is rendered fairly soluble in neutral ammonium citrate solution merely by heating it at a temperature below 600 °C, a property made the basis of a process patent by the junior author.' The possibility of producing an available form of phosphorus from what has hitherto been a worthless natural phosphate prompted the Bureau of Plant Industry, Soils, and Agricultural Engineering to make a brief study of the Pembroke phos- phate during the war years with a view towards determining the optimal temperature for heat treatment and the reactions involved in the process. The results of this study supplemented by data and information furnished by the junior author are presented in this paper. Description of Natural Phosphate: The phosphate with admixed quartz sand and siliceous matter occurs as a low-grade (8 to 9 pct P2O5) clay-like material that can be beneficiated cheaply by making a water separation of the very fine material from the sand, floating off the fine material, settling the suspension to a thick slurry, and finally de-watering the slurry by vacuum filtration followed by drying. The product dried at 100 °C contains about 16 pct water and 25 pct P2O5, about 1/12 of which is citrate soluble. Partial analyses of representative samples of the crude ore and corresponding concentrate are given in table I. The concentrate is light yellow in color and even after being dried at 100°C sticks very noticeably to laboratory grinding and screening equipment. Under the microscope the ground material is predominantly light brown crystalline aggregates with index of refraction near 1.61. The principal phosphate mineral constituent was identified as pseudo-wavellite with admixed phosphosiderite.2 Pseudo-

Jan 1, 1951

By W. L. Hill, W. H. Armiger, S. D. Gooch

The physical properties, chemical behavior under thermal treatment, and fertilizer value of fluorine-containing pseudowavellite (hydrous calcium aluminum phosphate) that occurs as phosphate clay admixed with quartz sand in an extensive deposit near Bartow, Fla., were determined by experiments in laboratory, pilot-plant, and greenhouse. When the mineral was heated at 500°C, 80 pct of the phosphorus become citrate soluble. The heated product, however, deteriorates markedly under moist conditions such as obtain in the soil. EXTENSIVE beds of a soft aluminiferous phosphate lie in the Bartow-Pembroke region of Florida. Although the extent of the deposit is unknown, it is thought that the equivalent of at least five million tons of material containing 25 pct P,Os exists on one large mine property alone, and soft phosphates similar in nature are known to occur elsewhere in the state. This aluminum phosphate, unlike fluorapatite, is rendered fairly soluble in neutral ammonium citrate solution merely by heating it at a temperature below 600 °C, a property made the basis of a process patent by the junior author.' The possibility of producing an available form of phosphorus from what has hitherto been a worthless natural phosphate prompted the Bureau of Plant Industry, Soils, and Agricultural Engineering to make a brief study of the Pembroke phos- phate during the war years with a view towards determining the optimal temperature for heat treatment and the reactions involved in the process. The results of this study supplemented by data and information furnished by the junior author are presented in this paper. Description of Natural Phosphate: The phosphate with admixed quartz sand and siliceous matter occurs as a low-grade (8 to 9 pct P2O5) clay-like material that can be beneficiated cheaply by making a water separation of the very fine material from the sand, floating off the fine material, settling the suspension to a thick slurry, and finally de-watering the slurry by vacuum filtration followed by drying. The product dried at 100 °C contains about 16 pct water and 25 pct P2O5, about 1/12 of which is citrate soluble. Partial analyses of representative samples of the crude ore and corresponding concentrate are given in table I. The concentrate is light yellow in color and even after being dried at 100°C sticks very noticeably to laboratory grinding and screening equipment. Under the microscope the ground material is predominantly light brown crystalline aggregates with index of refraction near 1.61. The principal phosphate mineral constituent was identified as pseudo-wavellite with admixed phosphosiderite.2 Pseudo-

Jan 1, 1951

By H. J. O’Donnell, B. C. Parks

IN 1930 the late Dr. Reinhardt Thiessen set up a method of microscopic analysis and type classification of coal that has since been followed as standard practice in the coal-petrography laboratory of the Bureau of Mines. Thiessen's terminology which designated the constituent parts of coal in terms of botanical origin was introduced in 1920.l The technique, however, of preparing a completely representative series of thin sections from a column sample of coal for use in making quantitative determinations of coal components with a microscope was developed about 10 years later by Thiessen and coworkers G. C. Sprunk and H. J. O'Donnell.2 Complete thin-section analyses subsequently have been made of 126 column samples of various ranks and types of American coals. The data and information were assembled from these thin-section studies and published in a large number of reports dealing chiefly with investigations of the coking and hydrogenation properties of certain American coals. In the years following adoption of Thiessen's method, a considerable amount of work was done in collecting column samples of many coals, making routine thin-section analyses of these, interpreting the results, and finding practical application for the information in other fields of coal research. The many reports and papers covering the work in coal petrography, however, offer very little discussion that can be considered as critical appraisal of the technique. Criticism outside the Bureau most often has voiced questioning opinions concerning the accuracy of the method used of measuring coal components microscopically and classifying the coal into arbitrary types on the basis of the quantitative determinations. The principal purpose of this paper is to discuss in some detail and present data showing the results of certain investigative work done in the petrography laboratory on the accuracy of the Bureau's method of microscopic measurement of components in coal thin sections. Data from microscopic analyses on file made by G. C. Sprunk and H. J. O'Donnell were freely used in the investigation, and a table of columnar analyses from an unpublished manuscript by Sprunk is included in this paper for reference. In the course of the experimental work a method was developed for measuring instrumentally with a planimeter the components shown in micrographs of selected thin sections. Measuring coal components with a planimeter furnished useful information for studying the accuracy of microscopically measuring the same components in thin sections. PETROGRAPHIC COMPONENTS AND TYPE CLASSIFICATION OF COAL Thiessen considered coal to be composed of two visibly different major components present in various types of coal in greatly varying proportions. He named

Jan 1, 1948

By R. F. Evans, J. M. Avert

Much has been written of the glamour of magnesium from sea water, the Aladdin-like creation of a huge magnesium plant in the Nevada desert using cheap hydroelectric power from Boulder Dam; the marvels of the Hansgirg process for the electrothermal reduction of magnesium oxide by carbon, and the ferrosilicon process for producing magnesium from dolomite. This is the story of the production of magnesium by the electrolytic process, using steam-electric power supplied by a public utility, in a plant at Painesville, Ohio, 30 miles east of Cleveland on the shore of Lake Erie. The story is not without interest, since it involves several unique developments that provide the answer to a question frequently asked: How is it possible to produce magnesium metal economically at such a location as Painesville, Ohio? Basically, the answer lies in making use of facilities already in existence for the production of soda ash, which makes it possible to manufacture magnesium chloride, the principal raw material, cheaply enough to offset the high cost of electric power. To this is coupled the successful conversion of by-product chlorine into a product required for the war program. The source of magnesium for this opera- tion is the enormous surface deposit of high-grade dolomite in the region south of Toledo, within reasonable freight haul of Painesville. This same geological stratum underlies the Painesville plant, but unfortunately at a depth of about 3000 ft.— apparently too great a depth to permit underground mining to compete with the delivered cost of rock from surface quarries in other areas. The cost of dolomite obviously is an important factor, since the rock contains only some 12 per cent magnesium (20 per cent MgO) so that one dollar on the cost of stone means more than $8 in terms of its magnesium content, and more than that in terms of recoverable magnesium metal. Production of Magnesia from Dolomite In the summer of 1941, the Diamond Alkali Co. was well along with construction of a plant intended for the commercial production of refractory and other grades of magnesia from dolomite. The process to be used was designed to make maximum economic advantage of existing plant and operations by tying the production of magnesia in with the manufacture of soda ash in such a way as to make use of the lime [CaO)., value of calcined dolomite. The process finally adopted after a lengthy research and development program has much in common with the old Clerc-Nihoul process, but includes certain innovations found to be necessary or advantageous. Essentially, the process is based upon the following series of reactions:

Jan 1, 1949

By R. F. Evans, J. M. Avery

MUCH has been written of the glamour of magnesium from sea water, the Aladdin-like creation of a huge magnesium plant in the Nevada desert using cheap hydroelectric power from Boulder Dam; the marvels of the Hansgirg process for the electrothermal reduction of magnesium oxide by carbon, and the ferrosilicon process for producing magnesium from dolomite. This is the story of the production of -magnesium by the electrolytic process, using steam-electric power supplied by a public utility, in a plant at Painesville, Ohio, 30 miles east of Cleveland on the shore 'of Lake Erie. The story is not without interest, since it involves several unique developments that provide the answer to a question frequently asked: How is it possible to produce magnesium metal economically at such a location as Painesville, Ohio? Basically, the answer lies in making use of facilities already in existence for the production of soda ash, which makes it possible to manufacture magnesium chloride, the principal raw material, cheaply enough to offset the high cost of electric power. To this is coupled the successful conversion of by-product chlorine into a product required for the war program. The source of magnesium for this operation is the enormous surface deposit of high-grade dolomite in the region south of Toledo, within reasonable freight haul of Painesville. This same geological stratum underlies the Painesville plant, but unfortunately at a depth of about 3000 ft. apparently too great a depth to permit underground mining to compete with the delivered cost of rock from surface quarries in other areas. The cost of dolomite obviously is an important factor, since the rock contains only some 12 per cent magnesium (20 per cent MgO) so that one dollar on the cost of stone means more than $8 in terms of its magnesium content, and more than that in terms of recoverable magnesium metal. PRODUCTION OF MAGNESIA FROM DOLOMITE In the summer of 1941, the Diamond Alkali Co. was well along with construction of a plant intended for the commercial production of refractory and other grades of magnesia from dolomite. The process to be used was designed to make maximum economic advantage of existing plant and operations by tying the production of magnesia in with the manufacture of soda ash in such a way as to make use of the lime (CaO) value of calcined dolomite. The process finally adopted after a lengthy research and development program has much in common with the old Clerc-Nihoul process, but includes certain innovations found to be necessary or

Jan 1, 1945

By W. B. Humes

The use of high vacuum on a large industrial scale in the ferrosilicon process for the production of magnesium marks the coming of age of an important new metallurgical technique. The economical production of reactive metals, such as magnesium, which combine with all the well-known furnace atmospheres, has until recently been successfully carried out only by electrolytic methods. It is now apparent that, through the use of high vacuum, the distillation or sublimation of many metals can be done industrially at much lower temperatures, and hence in much simpler equipment, than heretofore has been thought possible. At the beginning of the present emergency, when the ferrosilicon process of producing magnesium was brought to the fore, little was generally known about vacuum engineering, practices, and techniques. In a comparatively short time, the available equipment has been adapted, new equipment designed and built, and a fund of know-how evolved to make possible the production of thousands of pounds of magnesium per day at pressures less than 1/ r0,000 of an atmosphere. Pilot-plant operations have been consistently maintained at pressures even as low 2s one micron (0.001 mm.). These low pressures, which previously were regarded as prohibitively costly or impossible to attain, have been demonstrated as economically feasible on an industrial scale. Necessity for Vacuum The main function of vacuum in the ferrosilicon process, and hence in most vacuum smelting processes, is to lower the temperature at which the metal may be distilled or sublimed from the reduction mixture. A secondary function is to protect the distilled metal from attack by the furnace atmosphere and to permit the formation of a dense condensate. In the ferrosilicon process, magnesium is formed by the reaction between dolomite and ferrosilicon: 2(Mg0-Ca0) -\- HFeSU / t=> aMg + MFe + (CaO)2-SiO2 The metal is distilled from the pelleted charge at a free air pressure of about 0.100 mm. of mercury (100 microns). This low pressure is not needed for the reaction, but rather serves to protect the metal vapor from the oxygen or nitrogen of the atmosphere and permits the formation of a condensate free of pyrophoric material. The reaction proceeds at air pressures as high as several millimeters of mercury, and evidence has been offered to show that the actual equilibrium pressure of magnesium at operating temperatures of 2I50°F. is somewhat higher. Experimentation indicates that the yield begins to decrease at pressures above 500 microns. While no real operating data are yet available on the relationship between

Jan 1, 1944

By G. W. Cullen

Niobium-tin has been prepared on insulating suhstrates hby simultaneous hydrogen reduction of gaseous niobium and tin halides. Stoichiometric material is greater than 98.8pct theoretical density, appears to he single-phase, and has a total impirity level less than 0.3 at. pct. Transition temperatures and lattice constants may he related to composition. Typical current densities in various fields and orientations are given. IT is known that Nb3Sn carries large current densities in high fields, 1 and exhibits an unusually high transition temperature2 and critical field.3 For these reasons high-field solenoids have been constructed of this material.4 Because of the emphasis on solenoid fabrication, much of the materials research has been directed toward development of wire geometries wherein the brittle Nb3Sn is supported by a more malleable metal or alloy. There are, however, basic studies and applications that can be carried out only on Nb3Sn supported by an insulator. Insulating substrates are desirable for a number of reasons: the substrate does not interact with applied or induced currents and fields; diffusion of metallic species into the de- posit is avoided, both during the preparation and during subsequent heat treatment; irradiated samples are not more active than the deposit itself. Unsupported Nb3Sn geometries may also be prepared by preferential chemical dissolution of the insulating substrate. This report describes the preparation and properties of Nb3Sn deposits on ceramic substrates. Experiments currently utilizing material prepared in the manner described in this report include the following: dependence of current-carrying properties on field strength and orientation 5,6 radiation damage,7,8 tunneling,9 thermal conductivity (substrate removed),1° microwave surface impedance," tube magnetization,6,12 resistivity as a function of temperature,13 and current density and transition temperature as a function of annealing.14 Possible practical applications include magnetic shielding, superconductor generators, and frictionless bearings. PREPARATION Methods for the deposition of elemental niobium and tin by hydrogen reduction of the gaseous metal halides have been known for some time,15,18 but only recently a procedure was developed in this laboratory17 for the codeposition of these two metals on a hotwire as the intermetallic compound, Nb3Sn. This method of simultaneous hydrogen reduction of the gaseous niobium and tin chlorides is used for the preparation of Nb3Sn On ceramic substrates. The procedure differs from that employed on a hot wire in that insulating substrates cannot conveniently be heated to temperatures greater than their surround-

Jan 1, 1964