Search Documents

By A. R. Orban, R. B. Engdahl, J. D. Hummell

The initial phase of a research program on smoke abatement from Bessemer converters is described. In work sponsored by the American Iron and Steel Institute, a 300-lb experimental Bessemer converter was assembled to simulate blowing conditions in a commercial vessel. Measurements of smoke and dust were also made in the field on a 30-ton commercial vessel. During normal blows the dust loading from the laboratory converter averaged 0.51 lb per 1000 lb of exhaust gas. This was similar to the exhaust-gas loading of a commercial vessel. The addition of hydrogen to the blast gas of the laboratory converter caused a decided decrease in smoke density. Smoke was also reduced markedly when methane or ammonia was added instead of hydrogen. The research is continuing on a bench-scale investigation of the mechanism of smoke formation in the converter process. DURING the past 2 years, on behalf of the American Iron and Steel Institute, Battelle has been conducting a research program on the control of emissions from pneumatic steelmaking processes. The objective of the research program is to discover a practical method for reducing to an unobjectionable level the emission of smoke and dust from Bessemer converters. PRELIMINARY INVESTIGATION Although conceivably some new collecting technique may be devised which would be economically practicable for cleaning Bessemer gases, no such system based on presently known principles seems feasible because of the extremely large volume of high-temperature gases involved. Hence, the research is being directed toward prevention of smoke formation at the source. A thorough review was first made of former work to determine the present status of the cleaning of converter gases. No published work was found on work done in the United States on collecting smoke or on preventing its formation in the bottom-blown, acid-Bessemer converter. In Europe, however, a number of investigations have been made on the basic-Bessemer converter. Kosmider, Neuhaus, and Kratzenstein1 conducted tests on a 20-ton converter to obtain characteristic data for dust removal and the utilization of waste heat. They concluded that because of the submicron size of the dust, special equipment would be necessary to clean the exhaust gases. Dehne2 conducted a large number of smoke-abatement experiments at Duisburg-Huckingen in a 36-ton Thomas converter discharging into a stack. A number of wet-scrubbing and dry collectors were tried unsuccessfully. A waste-heat boiler and electrostatic collector with necessary gas precleaners was felt to be the best solution for this particular plant. Meldau and Laufhutte3 determined that the particle size was all below 1 µ in the waste gas of a bottom-blown converter. Sel'kin and zadalya4 describe the use of oxygen-water mixtures injected into a molten bath in refining open-hearth steel. They claim that with use of oxygen-water mixtures the amount of dust formed was reduced between 33.3 and 20 pct of its previous level, and emission of brown smoke almost ceased. Pepperhoff and passov5 attempted unsuccessfully to find some correlation between the optical absorption of the smoke, the flame emission, and the composition of the metal in a Thomas converter in order to determine automatically the metallurgical state in the melt. In a recent U. S. Patent (NO. 2,831,762)' issued to two Austrian inventors, Kemmetmuller and Rinesch, the inventors claim a process for treating the exhaust gases from a converter. By their method the inventors claim that the exhaust gases from the converter are cooled immediately after leaving the converter to a degree that oxidation of the metal vapors and metal particles to form Fe2O3 is inhibited in the presence of surplus oxygen. Gledhill, Carnall, and sargent7 report on cleaning the gases from oxygen lancing of pig iron in the ladle. They claim the Pease-Anthony Venturi scrubber removed 99.5 + pct of the smoke, thereby reducing the concentration to 0.1 to 0.2 grain per cu ft, which resulted in a colorless stack gas after the evaporation of water. Fischer and wahlster8 developed a small basic converter and compared the metallurgical behavior of the blow with that of a large converter. Later work by Kosmider, Neuhaus, and Hardt9 on the use of steam for reduction of smoke from an oxygen-enriched converter confirmed that the cooling effect of steam is detrimental to production. From review of all of the published information on the subject, it was concluded that a practical solution to the smoke-elimination problem had not been found. Accordingly, it was deemed desirable to investigate the feasibility of preventing the initial formation of smoke in the converter.

Jan 1, 1961

By M. Cohen, W. J. Harris

The recent application of lineal analysislt2 to the austenite-martensite reaction has made possible a quantitative study of the kinetics of this transformation during rapid cooling. Martensite range curves can thus be constructed to portray the onset of the reaction at Ma and its subsequent progress as a function of temperature down to and below the ambient. It now seems in order to investigate other aspects of the martensite transformation, using this quantitative method of approach. One of the least understood characteristics of the austenite-martensite reaction is that of stabilization which has been defined by Troiano and Greninger3 as 'la lowering of Ma, resulting from aging, without change in chemical composition of the parent solid solution." In other words, if the hardening quench is arrested at a predetermined subcritical temperature (TA) for a sufficient period of time, more austenite may be retained at a given lower Or reference temperature (Tr) than if the steel had been cooled directly and rapidly to Tr in the first place. For the purposes of the work at hand, the extent of stabilization produced by the isothermal treatment at Th is measured explicitly in terms of the excess austenite (6) that exists in the steel at T,, over and above the amount that is normally present after direct quenching to T,. T, is conveniently taken to be room temperature, but this choice is not essential and is sometimes undesirable. The holding temperature (TA) may be above or below M,, and still cause stabilization depending upon the themistry of the austenite. stabilization has been found to occur in the presence of bainite4 and of martensite6,6,7,8 as well as in the absence of either,g The phe-nomenon of stabilization is not concerned with (and may even be obscured by) ferrite formation or any other type of phase change occurring at T~ that alters the chemistry of the remaining austenite. Such a structural change would obviously influence the martensite transformation during subscquent cooling. Stabilization, however, is more subtle; it appears to manifest itself without detectable variation of the austenite composition, whether in the presence or absence of transformation products. There are relatively few direct references to stabilization in the literature. The stabilizing effect of room temperature aging and tempering on the subzero transformation of retained austenite has been clearly shown in plain carbon,6,8 low alloy6s7.8 and high alloy tool steels.10'5 ssa- with the as-hardened steel, the degree of stabilization increases with tempering time and temperature through

Jan 1, 1949

By D. A. Dahlstrom

Although the liquid-solid cyclone is a relatively recent innovation in the field of coal preparation, various authors have already indicated three distinct applications to operations encountered in the modern tipple. Driessen's articles and work at the Dutch State Mines exhibited its possibilities in the bene-ficiation of fine coal with apparently high efficiencies down to the 200-mesh fraction. l,2,3,4 Other publications point out its use as a recoverer, thickener, and preliminary dewatering agent of fine coal which in too many cases is being wasted due largely to former high operating cost limitations.M Finally, certain authors have emphasized the practicability of applying the cyclone to the elimination of coarse and fine solids from water slurries in the tipple in order to produce a water suitable for recycle purposes containing only minute particles far below the 200-mesh size.6 This would result in a closed water system for many cases, with its accompanying economic and operating advantages to locations where water quantity and quality problems are severe; better operation of washing equipment using a consistent water devoid of injurious fine particles; lowered maintenance costs due to the lesser abrasion resulting when the fine abraiding particles are removed; and the greater ease of disposing of refuse streams of reduced volume containing greater percentages of solids. While the three applications have been indicated to be feasible, only a meager amount of data is available on capacities and solid elimination eficiency as a function of design variables and cyclone friction loss. This information is essential for the optimum use and construction of the solid-liquid cyclone, and accordingly, work on the problem was initiated at Northwestern University. For the unfamiliar reader, briefly the cyclone consists of a cylindrical section mounted above a truncated cone. The feed nozzle enters the cylindrical ring tangentially with the underflow nozzle permitting discharge of the concentrated solids located at the apex of the cone. The overflow nozzle through which the clarified water exits is centered in the cylindrical section at the top of the cyclone. Half sections of experimental cyclones will be found in Fig la and 6. The feed slurry enters with a tangential velocity, thus creating a spiral pattern of high centrifugal force. The solid particles of sufficient size and gravity are ejected outward to the walls and spirally discharge to the underflow. Most of the water with uneliminated fine solids moves radially inward along the path of the outer

Jan 1, 1950

By M. Schwartz, S. K. Nash, R. Zeman

Knoop hardness in the rolling plane and in the longitudinal plane of hot-rolled and cold-rolled sheets of sublimed magnesiu?w was measured as a function of the angle between the long axis of the indenter and the rolling direction. These measurements were correlated with similar data taken on the (0001) and (1010) planes of a single crystal of magnesium where the hardness was measured as a function of the angle between the long axis of the indenter and the [1120] direction. The results were analyzed for compliance with the hypothesis of Daniels and Dunm to account for slip, and with a similar hypothesis to account for twinning. Some hardness anisotropy data are also presented for magnesium-indium and magnesium-lithium solid solution alloys. It is well known that the hardness of a crystalline specimen is different for its different surfaces, and also that the hardness is a function of direction within a single surface. Variations in hardness for single crystals have been found to be much larger than those for polycrystalline materials. Also, materials having low crystal symmetry were found to have a greater anisotropy of hardness than those of high symmetry. 0'Neill1 and Pfeil,2 using a 1-mm Brine11 ball, studied single crystals of aluminum and iron, respectively; and they found a variation of hardness of about 10 pct between readings taken along the principal crystallographic faces. Daniels and Dunn3 found that the Knoop hardness number varied about 25 pct as the long axis of the indenter rotated on the basal plane of a zinc single crystal. The variation on the (1450) plane was about 100 pct, and the average hardness on this plane was about twice that of the basal plane. They also studied the variation of hardness within the (loo), (110), and (111) faces of a single crystal of silicon ferrite and found variations of about 25 pct although the average values for these planes were almost identical. Single crystals of zinc were also studied by Meincke.4 He found that the Vickers hardness numbers varied about 30 pct depending on whether the axis of the indenter was parallel or perpendicular to the (1010) and (1110) planes. Mott and Ford,5 using a Knoop indenter, found a 25 pct variation in hardness on the basal plane of zinc. Crow and Hinsley6 studied heavily cold-rolled bronze, steel, brass, copper, and other metals. They found that the difference in hardness numbers based on the difference in the length of the diagonals of the Vickers indenter was from 5 to 12 pct. Some minerals and synthetic stones show a very large anisotropy of hardness. Robertson and Van Meter7 found the Vickers hardness of arsenopyrite to vary from 633 to 1148 kg per mm2. stern8 using the double-cone method on synthetic corundum found the hardness number to vary from 950 to 2070. And winchell9 reported a variation of hardness number from 184 to 1205 in kyanite. The variation of hardness as a function of direction in a given crystallographic plane in single crystals possesses a periodicity which is related to the symmetry of the lattice. Daniels and Dunn3 found a six-fold periodicity of hardness in the (0001) plane of zinc. They found that the hardness curves of silicon ferrite had a four-fold symmetry in the (100) plane, a two-fold symmetry in the (110) plane, and a six-fold symmetry in the (111) plane. Mott and Ford5 also reported a six-fold symmetry of hardness in the basal plane of zinc. And vacher10 found two-, four-, and six-fold periodicities of hardness in copper on the (110), (100), and (111) planes, respectively. The purpose of this paper is to report the results of an investigation on the anisotropy of hardness as a function of orientation in single crystals of mannes-ium, and samples of rolled magnesium, magnesium-indium, and magnesium-lithium solid solution alloys. The anisotropy of hardness of pure magnesium which had been hot rolled, and then cold rolled various amounts to fracture, was studied by means of Knoop indentation hardness numbers; and the results were correlated with the preferred orientation as determined by quantitative X-ray pole-figure data. A comparison was made of the hardness data obtained from the rolled sheets and those of single crystals of magnesium. In order to obtain a more fundamental understanding of the variation of hardness and of Knoop hardness testing, the data were analyzed by

Jan 1, 1962

By Neils Hansen

The microstructure of dispersion-strengthened aluminum aluminum-oxide products containing from 0.2 to 4.7 wt pct of aluminum oxide has been examined by optical and transmission electron microscopy, and the flow stress has been determined at room temperature and at 400C by tensile testing. Products were examined as recrystallized and as high-temperature extruded, and the microstructures consisted of a fine dispersion of oxide particles in a matrix divided by respectively recrystallized grain boundaries and subgrain boundaries. The flow stress (0.2 pct offset) at room temperature of recrystallized dispersion strengthened aluminum aluminum-oxide products is the superposition of dispersion strengthening and grain boundary strengthening. This superposition has been found to be linear. The flow stress (a) can be related to the grain size (t) by the Petch equation: ing content of oxide and k is a constant independent of the oxide content. For extruded products a similar relation has been found by replacing the grain size by the subgrain size. The k-value is of the same order for the two types of structure, which shows that the subgrain boundaries are as effective slip barriers as grain boundaries. Tensile testing at 400C of re-crystallized and extruded products shows that oxide dispersion strengthening is very effective, whereas the strengthening effect of grain boundaries and subgrain boundaries is small. THE microstructure of dispersion-strengthened products consists of hard particles finely distributed in a metal matrix. The strengthening effect of the dispersed phase has been fairly well established,1 and it has been found that the size and volume fractions of the dispersed particles are important structural parameters. However, in many dispersion-strengthened products which have been worked and heat-treated during manufacture the matrix is divided into well-defined grains or sub-grains, which may also have a strengthening effect. A model of the matrix strengthening in dispersed products worked during manufacture has been proposed,2 introducing the energy of the structure as a strengthening factor, especially at low temperatures. A difficulty in this model is, however, to relate this (stored) energy to the structural parameters directly observable as for instance grain size. The strengthening effect of the matrix grain size after recrystallization has been in- vestigated for nickel-thoria (TD-Nickel) products3 and for copper aluminum-oxide products. Conclusive results were, however, not obtained as the grain size of TD-nickel was constant. 5 to II , after recrystallization at temperatures from 700 to 1200°C and as the copper products containing 5 to 1 wt pct of aluminum oxide could not be recrystallized even after severe cold reduction and heat treatment at 1050C. For aluminum aluminum-oxide products containing from 1 to 5 wt pct of aluminum oxide it has been shown that the tensile strength at room temperature decreases when an extruded product is cold-worked and recrystallized. The matrix in the extruded products is divided into well-defined subgrains of micron size, and as the grain size of the recrystallized products is about two orders of magnitude higher, it is obvious that grain boundary strengthening occurs. Preliminary results8 have indicated that the flow stress containing no grain boundaries, A is a constant and t is the subgrain size. At elevated temperatures the effect of boundaries is more complex; it has been shown11 that recrystallized products having an oxide content of about 3 wt pct are more creep resistant than extruded material in the temperature range 400° to 600°C, whereas on application of a higher strain rate the tensile flow stress (0.2 pct offset) is higher in extruded than in recrystallized aluminum—5 wt pct aluminum oxide products at temperatures from room temperature to 427°C (800), Finally it has been shown12 that the Brinell hardness at 350°C of extruded products having about the same content of aluminum oxide increases with decreasing grain size, determined by X-ray line-width measurements. The present study was undertaken to obtain a quantitative relationship between the tensile strength and the grain size of aluminum aluminum-oxide products in the recrystallized as well as in the extruded state. The tensile testing was performed at room temperature and at 400uC. The grain size of the recrystallized products was varied by changing the degree of cold-work preceding the recrystallization heat treatment. In extruded products grain (or subgrain) size variations were obtained by high-temperature heat treatment after extrusion. EXPERIMENTAL a) Materials. Aluminum aluminum-oxide products have been manufactured by consolidation of aluminum powder covered with a layer of aluminum oxide formed during powder manufacturing. The products examined were manufactured from atomized powder containing

Jan 1, 1970

By C. D. Hall, F. E. Dollarhide

Fluid Ioss agent.s for crude oil and for water have been studied in dynamic tests. A treatment using a spearhead with a fluid loss agent followed by plain fluid appears feas ible in crude oil, but not in water. An equation for spearhead depletion shows that spurt loss relative to fracture width must be low, if the portion of spearhead fluid in the treatment is to be small. The presence of colloidal matter in crude oils aids the fluid Ioss agent. Unlike in kerosene, where flow limited the agent deposition, in crude oils the filter cake continually formed and leak-off declined. The volume-time relation varied somewhat for different crudes, but was best described by a square root of time function. Spurt loss was inversely proportional to agent concentration. After the fluid loss agent initiated the filter cake, the crude oil colloids built on it effectively. A 2-minute or a 5-minute spearhead with double the normal agent concentration gave the same fluid Ioss curve as the same concentration did for a 30-minute test. The agents tested in water gave fluid Ioss plots on which, for the first few minutes, volume was proportional to the square root of time, but later became proportional to time. For fracture area calculation the customary square root of time function is a satisfactory approximation. Leak-off rates and spurt losses were higher in water systems than in oils. The spurt Ioss tended to be inversely proportional to concentration. In spearhead tests, the filter cakes were not eroded by water flow. However, the rather high spurt loss values make spearhead treatments impractical for water-based fluids. Introduction The effects of dynamic testing conditions on the performance of fluid loss agents in kerosene have been studied previously.' We have extended the work to include crude-oil- and water-based fracturing fluids. An understanding has been gained of the mechanisms of formation and functioning of the filter cakes of fluid loss agents. The practical aspects of evaluating performance of agents in relation to fracture area calculations also are considered. The feasibility of using the fluid loss agent in a spearhead stage of the treatment is examined further for both types of fluids. Experimental Procedure The dynamic fluid loss tests were performed in an apparatus similar to the high-pressure apparatus described in a previous publication.' A fracturing fluid was circulated over a rock surface located in a closed pressurized loop. The fluid flowed axially over the cylindrical surface of a core 2 in. in diameter X 3.5 in. long, mounted (with the flat ends sealed off) in a pipe, with 0.117 in. annular clearance. The filtrate was collected in a central hole in the core and led through valves to graduated cylinders. Provision was made for changing quickly the circulating fluid during the test (spearhead runs) without interrupting the filtration pressure. The only modifications were to add heating tapes and water jackets for the tests with crude oils, all conducted at ISOF, and to change all parts exposed to the test fluid to stainless steel for the tests with water-based fluids. The latter tests were made at room temperature, 80F. Three crude oils were tested. A mixed crude, obtained from a local refinery, contained a considerable amount of light ends. For safety reasons, it was stripped to 250F vapor temperature before use in the fluid loss tests. The other two oils were used as obtained from lease tanks. One was a greenish-brown, 37" API paraffinic crude, and the other was a black, 32" API asphaltic crude. The fluid loss agent for oil, here designated for brevity as Agent A, was Adomite@ Mark II*, a granular solid commercial agent, the same as previously tested in kerosene.' Three different compositions of fluid loss agents were tested in Tulsa tap water. Agent B was adomit& Aqua*, a solid commercial fluid loss agent, comprising clays and hydrophilic gums principally derived from starch. Agent C was a mixture of three parts of Agent B with two parts of silica flour. Agent D was Dowel1 J137, a mixture of guar gum and silica flour. The test cores were cut from contiguous blocks of Berea or Bandera sandstones. For the oil tests, the cores were oven dried, evacuated, saturated with kerosene, and the kerosene permeability was measured. The cores used with the water-based fluids were pretreated by saturating with 3 percent calcium &loride solution to minimize pemeability damage by the fresh water due to clay migration. The

Jan 1, 1969

By W. T. Bishop, G. A. Crowe

While the literature in the United States on general polarographic technique is extensive, very little appears to be directly applicable to the analysis of flotation tailings. For this reason, it seemed worth while to present a few polarographic methods of ore analysis that have been in constant use in the laboratories of the Hercules Experiment Station for the past few years. At the time of our initial investigation of the polarographic method, there was little or no mention of its specific application to flotation tailings. It was therefore necessary for us to establish suitable conditions for the analysis of our flotation tailings and to consider possible interfering constituents. The polarograph, or dropping mercury electrode, method was discovered in 1925 by J. Heyrovsky and M. Shikata,1 of the Charles University, Prague. This method has since received extensive development and the literature contains many articles on the use of the polarograph for the quantitative determination of metals as well as anions, oxygen in solution, and reducible organic compounds. Kolthoff and Lingane,² by the publication of their book, "Polarography," in 1941 did much to advance the knowledge and use of the polarograph. In chapter 25 of that book, methods for the polarographic analysis of brass, steel and iron products, alloys, and zinc ore are given. Aluminum,³ cadmium,³,4 cobalt,4 cop-per,³-9 gold,10 iron,3,11 lead,³,l2,l³ molybdenum,14 nickel,4,8,9 tin," and zinc³,4,5,7 in ores have been analyzed by the polarograph. However, most of the work on tailing samples has been published in Russian journals and translations are not yet readily available. In this paper we will describe the method that was developed and used in our laboratory for the determination of copper, zinc, and lead in flotation tailings. Principle OF the Method The polarograph is an instrument for applying a potential to a mercury pool and a dropping mercury electrode separated by a solution, and for measuring the resultant electrical current. The procedure is essentially a small-scale electrolysis, in which the voltage required to reduce or oxidize the material identifies it qualitatively and the current measures the concentration quantitatively. Different constituents in a sample may often be determined simultaneously provided they reduce at sufficiently different voltages. An example is the determination of copper and zinc in the same solution. The reduction potentials are quite far apart, as shown in Fig. I. The polarographic method is particularly useful in the range of concentration between those normally determined by spectographic and chemical methods. In

Jan 1, 1947

By G. A. Crowe, W. T. Bishop

While the literature in the United States on general polarographic technique is extensive, very little appears to be directly applicable to the analysis of flotation tailings. For this reason, it seemed worth while to present a few polarographic methods of ore analysis that have been in constant use in the laboratories of the Hercules Experiment Station for the past few years. At the time of our initial investigation of the polarographic method, there was little or no mention of its specific application to flotation tailings. It was therefore necessary for us to establish suitable conditions for the analysis of our flotation tailings and to consider possible interfering constituents. The polarograph, or dropping mercury electrode, method was discovered in 1925 by J. Heyrovsky and M. Shikata,1 of the Charles University, Prague. This method has since received extensive development and the literature contains many articles on the use of the polarograph for the quantitative determination of metals as well as anions, oxygen in solution, and reducible organic compounds. Kolthoff and Lingane,² by the publication of their book, "Polarography," in 1941 did much to advance the knowledge and use of the polarograph. In chapter 25 of that book, methods for the polarographic analysis of brass, steel and iron products, alloys, and zinc ore are given. Aluminum,³ cadmium,³,4 cobalt,4 cop-per,³-9 gold,10 iron,3,11 lead,³,l2,l³ molybdenum,14 nickel,4,8,9 tin," and zinc³,4,5,7 in ores have been analyzed by the polarograph. However, most of the work on tailing samples has been published in Russian journals and translations are not yet readily available. In this paper we will describe the method that was developed and used in our laboratory for the determination of copper, zinc, and lead in flotation tailings. Principle OF the Method The polarograph is an instrument for applying a potential to a mercury pool and a dropping mercury electrode separated by a solution, and for measuring the resultant electrical current. The procedure is essentially a small-scale electrolysis, in which the voltage required to reduce or oxidize the material identifies it qualitatively and the current measures the concentration quantitatively. Different constituents in a sample may often be determined simultaneously provided they reduce at sufficiently different voltages. An example is the determination of copper and zinc in the same solution. The reduction potentials are quite far apart, as shown in Fig. I. The polarographic method is particularly useful in the range of concentration between those normally determined by spectographic and chemical methods. In

Jan 1, 1947

By J. Larsen-Badse

The resistance to dry sliding abrasion us been measured for some hardened and tempered carbon steels. The wear resistance, defined as the reciprocal of the volume loss per unit sliding distance, is found to vary linearly with the hardness of the abraded surface. The data fit two lines, one, of high slope, for the pure metals and for the annealed steels and another, of smaller slope, for the hardened and tempered carbon steels. A relationship is developed showing the alwasion resistance to be proportional to the hardness of the material and to en, where n is the exponent of work hardening. The values of n and of the hardness FOR most materials a high resistance to abrasion is generally associated with a high value of indentation hardness. Brine11 even used the abrasion resistance as a measure of hardness in an attempt at expanding the hardness range covered by his indentation-hardness test.' When comparing different types of materials there is, however, only a very general relation between abrasion resistance and hardness. Sample brittleness seems to contribute to the deviation from a direct relationship. In general, increased brittle- are those relating to the heavily deformed abraded surface. However, for materials having n constant or varying m a regular manner over a wide range of strailts, the wear resistance will also be a linear function of the bulk hardness of the material. For tempered steels containing a dispersion of cementite in ferrite the increase in wear resistance due to the dispersion is found to be a linear function of the volume fraction of Fe3C and of the reciprocal of the mean free ferrite path. This indicates indirectly that the yielding of this material, when it is already heavily deformed, follows the Orowan criterion. ness leads to decreased abrasion resistance.' When comparing materials in the same group, e.g., the metals, the spread is less. Kruschov found that the abrasion resistance of pure metals and of annealed steels is directly proportional to the hardness of the metal. For hardened and tempered steels he obtained another linear relationship, one of smaller slope and intersecting the line for the pure metals at the location of the data for the annealed steels. He also found that the abrasion resistance of cold-worked metals is independent of the degree of cold working. This shows, as he concluded, that the process of abrasion work hardens the metal in the surface region to a very high degree.

Jan 1, 1967

By B. W. Vallat

(San Francisco Meeting, October, 1911.) THE Newport mine, located at Ironwood, Gogebic county, Mich., on the Gogebic iron-range, is owned and operated by the Newport Mining Co., for the mining of iron-ore. I. GEOLOGY. The general geology of the Gogebic range has been determined and recorded at different times by well-known geologists,) and their work will be referred to briefly in connection with the local conditions in the mine. The strike of the formation across this property is about 15° north of east. The, general dip is 68° to the north. At the base of the formation on the south lies the granite. Looking north, at right angles to the strike of the formation, we have the foot-wall of quartz-slates and quartzite about 400 ft. wide; the iron-formation about 800 ft. wide, and the hanging-wall of black slates. The iron-formation is composed of banded jasper and quartzite together with iron oxide and concentrations of iron-ore. In character the ore is a soft red hematite, with occasional masses of hard blue "steel ore." The formation is crossed in many places by diorite dikes, which cut through at various angles, the larger or main dikes dipping into the foot-wall in a SE. direction at angles varying from 15° to 30°, while numerous small dikes occur which strike through the formation in a vertical plane and at approximately right angles to the main dikes. There are various theories concerning these dikes, especially as to the time of their origin with relation to the ore-deposition. The commonly-accepted theory is that the dikes were there first, but there are some who contend that they were formed

Nov 1, 1911

By E. T. Turkdogan, P. Grieveson

Experimental results are presented for the rate of solution of nitrogen in a iron in the temperature range 750° to 873°C and in 6 iron in the temperature range 1410° to 1470°C. It is shown that the rate controlling process is diffusion of nitrogen into the iron. The diffusiting of nitrogen in a and 6 iron is derived from the results, and the temperature dependence of the diffusivity is represented by the equation D = 7.8 x e- 18,900/RT sq cm per sec. The solubility of nitrogen in a and 6 iron, in equilibrium with 1 atm pressure of nitrogen, has been measured. Using these results and other available data, it is found that the variation of the logarithm of nitrogen solubility with the reciprocal of absolute temperature is nonlinear. In an Appendix, some results of Darken and Smith are presented for the rate of solution of nitrogen in iron using ammonia + hyidrogen mixtures. These data also support the view that diffudsion of nitrogen in iron is the rate-controlling process when ammonia + hydrogen mixtures are used. A considerable effort has been made to obtain data on the solubility1-5 and diffusivity of nitrogen in a iron6-l2 because an understanding of the effect of nitrogen on the properties of steel must be based on an accurate knowledge of the properties of nitrogen in pure iron. However, no information is available concerning the kinetics of solution of nitrogen in a and 6 iron. Recently the authors13 have investigated the rate-controlling mechanism operating in the kinetics of solution of nitrogen in y iron. This study was directed to determine the rate-controlling processes for similar reactions with a and 6 iron as well as to establish values for the solubility of nitrogen in equilibrium with nitrogen gas in a and a iron. EXPERIMENTAL The procedure used in experiments to determine the rate of solution in cylindrical iron rods was the same as that described in a previous communication.13 Ferrovac E grade iron used in all experiments contained the following impurities in weight percent: C, 0.005; Mn, 0.001; P, 0.002; S, 0.006; Si, 0.006; Ni, 0.025; Cr, 0.002; V, 0.004; W, 0.02; Mo, 0.01; Cu, 0.001; Co, 0.01; 0, 0.007. After cleaning the surface, the iron rods were treated in an atmosphere of purified hydrogen for 17 hr before the reacting gas was introduced for known experimental times. After quenching, the samples were sectioned radially and analyzed for nitrogen. In addition to experiments using rods, iron foils were used in the measurements of solution rates of nitrogen in a iron. The foils of two different thicknesses were prepared by cold rolling Ferrovac E grade iron cylindrical rod to 0.051 and 0.152 cm. Foil samples were used in a rectangular form 5 cm long and 1.25 cm wide. The specimens were thoroughly cleaned of surface oxide with fine emery cloth and degreased with carbon tetrachloride immediately before entry into the furnace. The experimental procedure was the same as that used in the study with rods. At the completion of an experiment, the foil samples of the nitrogenized iron were analyzed for nitrogen after discarding 0.3 cm from the perimeter of the specimen. Iron foils were nitrogenized and denitrogenized in the a and 6 range with a gas mixture of 95 pct N and 5 pct H for times varying from 5 min to 2 hr. Results obtained for the average composition of nitrogen in iron for these experiments are presented in Fig. 1. Prior to the denitrogenization experiments, the samples were saturated with nitrogen at 1000°C and 0.67 atm N, giving a uniform nitrogen concentration of 0.0204 pct. According to the known a-y phase boundary in the Fe-N system,14 this composition lies within the ferrite region at temperatures 750" to 850°C. Use of this initial nitrogen content insured that reaction occurred between the gas and a single solid phase, a iron. Examples of the results for the mean concentrations of nitrogen in cylindrical iron rods, 0.356 cm radius for both the a and 6 ranges are given in Fig. 2. Typical examples of the results obtained for the radial distributions of nitrogen in rods are presented in Fig. 3. It appears that the results for radial distributions can be extrapolated to constant surface compositions which agree with the equi-

Jan 1, 1964

By R. L. Fleischer, W. F. Hosford

Tensile data for coarse grained aluminum Polycrystals suggest that the "grain size" effect is not due to dislocations piled up at grain boundaries but rather is primarily a relative size effect due to surface crystals being weaker and less confined. STUDIES directed at interpreting hardening of poly-crystalline metals normally identify their strain hardening properties with those in some particular type of single crystal.1"4 The recent recognition in face centered-cubic metals of a nearly linear stage with rapid hardening occuring at comparable rates for both polycrystals and single crystals, suggested that the same process or processes determine both cases and hence that there exists some justification for the use of single crystals to understand polycrystals. Further evidence for the above view may be found by an approach initiated by Chalmers:5 By using bicrystals of controlled orientation it is possible to begin to assemble a polycrystal and also to study grain boundary effects in detail. In this way it has been found that a single grain boundary affects easy glide but not the subsequent stage II hardening.6 This result suggests that a sensitive way to observe grain boundary effects in polycrystals would be to vary grain size and measure easy glide. As will be seen, easy glide is only possible for coarse-grained samples, and hence the results will serve to fill in the gap in measurements between single crystals and bicrystals on one hand and fine-grained polycrystals on the other. One problem inherent in comparing single crystals with polycrystals is the uncertainty as to what slip systems are acting in a polycrystal. To compare the two types of samples, rates of shear hardeninn---L. on the acting -planes are needed. and these may be computed only if it is known what particular systems are active. The acting systems were examined for a coarse-grained polycrystal and it will be shown that the systems supplying the preponderance of slip can be determined with little ambiguity. EXPERIMENTAL PROCEDURE Twelve samples of aluminum were prepared by chill casting into a heated graphite mold, followed by annealing at 635° ± 5°C for 24 hr with an 8-hr fur- nace cool, and finally either etching7 or electropol-ishing.' The samples, with a 7 to 10 cm length between grips and 4.4 by 6.6 mm in cross section, were deformed at a strain rate of about 3 10 -3 . per min in a tensile device which has been described elsewhere.5 The composition was reported by Alcoa as 99.992 pct Al, 0.004 pct Zn, 0.002 pct Cu, 0.001 pct Fe, and 0.001 pct Si; nine samples were deformed while immersed in liquid helium and three in air at room temperature. The stress-strain curve for one of the samples (P-1) deformed at 4.2 "K has been reported previ~usl~.~ This sample was selected for determination of active slip systems. Eighteen of the crystals were examined by optical microscopy to determine the angles of slip line traces and by X-ray back reflection to determine orientation. By this means the slip planes were determined and the resolved shear stress factors for possible slip systems could be computed. Finally each sample was sectioned so that after etching, the number of crystals could be counted for each of ten newly exposed surfaces. The average of these ten values will be termed n, the number of crystals per cross section. Values of 11, varied from 1.9 (nearly bamboo structure) to 12.7. Sketches of typical cross sections appear in Fig. 1. RESULTS AND DISCUSSION: SLIP SYSTEMS 1) Determination of Acting Slip Planes—The stress axis orientation and operative slip planes in eighteen crystals of sample P-1, as determined by slip line traces and crystal orientation, are summarized in Fig. 2. For one of the crystals two planes had a common trace. so that the traces alone did not distinguish which plane or planes were slipping. However it was found that the stress resolving factor for the primary system was 0.386, .while that for the most stressed system in the other plane (indicated bv the dotted arrow) is 0.138. It will be assumed tgerefore that only the primary plane acted. Since the orientations were determined after extending the samples 4 pct, the stress axes may be rotated from their original value by as much as 2 deg in some cases. It is interesting to note that in five crystals only one slip plane acted, in eight two acted, and in five three planes were observed—an average of two slip

Jan 1, 1962

By E. Miller, J. M. Eldridge, K. L. Komarek

The thermodynamic properties of liquid Mg-Ge alloys have been determined between 1000°and 1500°K by an isopiestic method. Germanium specimens, heated in a temperature gradient and contained in covered graphite crucibles of special geometry, were equilibrated with magrtesium vapor in closed titanium tubes. The crucible design allowed free access of magnesium vapor to the samples during the equilibration to form alloys of magnesium and germanium, but prevented magnesium losses from the crucibles on quenching the titaniuin tubes to terminate the experimental runs, thus preserving the equilibrium alloy compositions. The activities and partial molar enthalpies of magnesium and the integral thermodynamic properties of the system were calculated from the experimental data. THE Mg-Ge phase diagram' shows one congruent melting compound, Mg2Ge, of essentially stoichio-metric composition, two eutectics, and very limited terminal solid solubilities. Very little information is available on the thermodynamic properties of the Mg-Ge system. The free energy of formation of Mg,Ge was recently deter-mined2 by a Knudsen cell technique in the temperature range 610° to 760°C. The standard enthalpy of formation of Mg,Ge was measured calorimetrically by Bever and coworkers.3 The present study was undertaken as part of a general investigation of the thermodynamic properties of the homologous series of Mg-Group IVB systems, i.e., Mg-Pb,4 Mg-Sn,5 Mg-Ge, and Mg-Si. An isopiestic technique was used which was developed by the authors5 for investigating the thermodynamic properties of liquid Mg-Sn alloys. Specimens of the nonvolatile component, contained in covered graphite crucibles, are heated in a temperature gradient in an evacuated and sealed titanium reaction tube, and equilibrated with magnesium vapor of known pressure. The method employs crucibles of special geometry which preserve the high-temperature equilibrium composition of liquid alloys having a highly volatile component such as magnesium on termination of the experimental runs by quenching the crucibles to room temperature. EXPERIMENTAL PROCEDURE First reduction germanium of 99.999+ pct purity (Eagle-Pitcher Co., Cincinnati, Ohio) and 99.99+ pct magnesium metal (Dominion Magnesium Ltd., Toronto, Canada) were used. The graphite crucibles were machined from high-density (1.92 g per cu cm) graphite rods (Basic Carbon Corp., Sanborn, N.Y.) which had a maximum ash content of less than 0.04 pct. The non-reactivity of graphite with germanium at the temperatures used in this study had been previously established by Scace and Sleck.6 The experimental procedure has been previously described in detail.5 The selection of a particular crucible geometry for a run was determined by a combination of imposed experimental conditions, the principle being that more tightly covered crucibles were required to preserve alloy compositions during quenching when higher magnesium pressures and higher specimen temperatures were used. Depending upon the composition range of the equilibrated alloys the source of the magnesium vapor was either pure magnesium or a two-phase mixture of Mg2Ge + Ge-rich liquid of known magnesium pressure. The experimental runs can be divided into the following three groups on the basis of crucible geometry and magnesium source material. Crucibles with Small Holes and Pure Magnesium Reservoirs. The crucible dimensions were identical to those of the Mg-Sn investigation5 except that the hole diameters were reduced to 0.010 in. because of the higher temperatures and higher magnesium pressures involved in the Mg-Ge system. During an equilibration run, magnesium vapor diffused from the reservoir to each specimen through the small holes, one drilled through the crucible lid and two others drilled through graphite baffles positioned vertically inside the crucible between the lid hole and the specimen. Since the magnesium pressure was high, i.e., in the range 117 to 277 Torr, during the equilibration time of approximately 24 hr, equilibration was not impeded by these holes. A specimen composition at equilibrium was fixed by the relative temperatures of the specimen and the reservoir, and by the thermodynamic properties of the system. Upon brine quenching the titanium reaction tube to end a run the vapor pressure of magnesium above the liquid alloys decreased exponentially with decreasing temperature, and the small cross-sectional areas of the holes (4.9 x 10"* sq cm) drastically reduced magnesium losses from the crucibles. Because of its low vapor pressure, germanium losses from crucibles during a run were at most 0.2 mg for pure germanium and correspondingly less for the alloys. This crucible geometry satisfactorily retained the equilibrium alloy compositions on quenching for magnesium-rich (from 3 to 33 at. pct Ge) alloys provided their temperatures were below the melting

Jan 1, 1967

By Samuel G. Lasky

What the evidence prevails upon the mind to believe, depends upon the mind as well as upon the evidence. M. L. IN a recent discussion of the mineral resource position of the United States, published in the September 1946 issue of MINING AND METALLURGY, I expressed my conviction that ore deposits of major magnitude remain to be found in this country and that they can be found without undue cost or risk. I stated with equally strong conviction, however, that if the search for such deposits is to be notably successful there must be, among other things, a reorientation of philosophy and mental habits on the part of many who would be connected with the search. I would now like to enlarge upon that statement. For such a purpose, we may consider that the search for concealed deposits involves four steps: (I) the selection of areas for further study; (2) the geologic study of those areas in order to verify their general favorableness and in order to choose specific patches worthy of being tested; (3) the decision whether exploration of the patches chosen should actually be undertaken; and (4) the exploration itself. The first two steps and the last rest upon the judgment and skill of geologists. The third step-the decision whether exploration should be undertaken-rests upon management. In my opinion, the philosophies or principles that have guided these steps in the past are now inadequate. PHILOSOPHY OF APPRAISAL If concealed deposits are to be looked for, how are the places of their possible concealment to be recognized? Every known mineralized area still in the prospect stage has already been repeatedly examined and condemned. As for those deposits concealed under later rocks, there may be not even the clue of a near-by outcrop for engineer or geologist to consider. How then, are we to know where to look? Geologic Probability In the early days of our mining industry, ore deposits were found mainly by "following the ore." Later, as such opportunities decreased, and as geologic concepts became accepted, deposits were found more and more through use of the notion of geologic probability. Many instances can be cited wherein a courageous operator ignored the implications of the unsuccessful efforts of predecessors and, solely by "following the ore," converted a discredited prospect into a good mine. Similar experience doubtless will occur in the future, but "following the ore" will no longer in itself find new deposits in the amount needed. Nor can enough new ore be expected from further use of the notion of geologic probability, for, as mentioned above, our known prospects `have already been ex-

Jan 1, 1947

By H. I. Aaronson, C. Laird

Although the past results of X-ray experiments indicate that the broad faces of 0' plates are coherent with their matrix, dislocations lying in arrays have frequently been observed at these boundaries by transmission electron microscopy. Critical experiments employing the latter technique have been carried out in order to determine the origin of these dislocations. It is concluded that 8' plates are essentially coherent with the matrix at their broad faces throughout the aging temperature/time envelope studied. Virtually all of the dislocation arrays observed are deduced to have been formed by plastic deformation accompanying transformation. The proportion of dislocations arising from convexity of the plates is shown to be negligible by comparison with that from plastic deformation. At the higher aging temperatures, a[001] dislocations appeared in moderate numbers. These dislocations were traced directly, however, to the ledgewise dissolution of 0' occasioned by the formation nearby of 0 crystals. On the other hand, since there is a parametric difference normal to the broad faces of the ?' plates, mismatch dislocations do form at their edges. A previous conclusion that these dislocations have Burgers vectors of type a[001] was confirmed directly. The edges of 0' plates were observed to develop octagonal shapes when growing, but circular shapes during dissolution. 1 HIS paper presents the results of an investigation of the interfacial structures of plates of the transitional phase, 8', formed in an A1-4 pct Cu alloy. In a companion paper, Part 11, the effects of these structures upon the migration kinetics of a:?f boundaries are reported. This work is pa.rt of a general program designed to establish the basis of precipitate morphology. The present authors in Al-Ag,1 and whitton2 previously in U-C alloys, have used transmission electron microscopy to examine directly the vander Merwe3-6 networks of dislocations anticipated7 to compensate the small amount of lattice misfit normally founda at the broad faces of Widmanstatten plates. Since the broad faces of 0' plates are considered to be perfectly coherent with the corresponding habit planes in the a matrix,' no dislocations should be present at these faces. Many reports have been published, however, giving evidence to the contrary.10-18 The primary objective of this investigation was therefore to ascertain the nature of these dislocation structures. An attempt to do this is described in the first three sections of this paper. Inspection of the matching of the a and 8 ' lattices at the orientations of the 0:0' boundary corresponding to the edges of 0' plates raises the possibility that these edges may be made up of rather closely spaced edge- type misfit dislocations oriented so as to be sessile with respect to the lengthening or shortening of the plates. Since this structure should severely inhibit migration of the plate edges (Ref. 7, Part II), a situation not originally anticipated,' an experimental determination of the interfacial structure of the edges of 8' plates was clearly in order, and is reported in Section III. Those aspects of the experimental procedure applicable to both Parts I and I1 are presented in the next section. Specific procedures applicable to individual aspects of each investigation, and also the relevant surveys of the literature, are then individually reported in the appropriate sections. I) GENERAL EXPERIMENTAL PROCEDURE The material used in both parts of these studies was the same as that of a previous investigation:" strips of A1-3.93 pct Cu, 0.009 in. thick, prepared as before, solution-annealed at 548°C for 6 hr, and quenched. Details of subsequent aging, and in some cases deformation treatments, are given in the Experimental Procedure sections of the individual parts of both papers. Specimens of the heat-treated strips were electro-thinned as beforeLg and examined in a Philips EM 200 microscope equipped with a goniometer stage. A commercial hot stage, of the grid-heater type and capable of * 30-deg tilt about one axis in the plane of the specimen, was also used for kinetic studies. The usual precaution of calibrating for the additional heat supplied by the electron beam was taken.19 A 16-mm cine cam-I era mounted outside the viewing window was frequently used to record the transformations. Conventional selected-area diffraction and dark-field viewing techniques were used to identify the precipitates in the foils. Normal bright-field images corresponding to two-beam diffracting conditions or dark-field images were employed to characterize the dislocations observed at the interfaces of the precipitates. The application of these techniques to the study of an interphase boundary, and the interpretation of the images,20'21 has been fully described in a previous paper.'

Jan 1, 1969

By S. G. Epstein

Using the capillary-reservoir technique, electromi-gvation rates of cadmium and indium in liquid bismuth were measured at several temperatures. The electric mobility of cadmium Jrom 305° to 535°C and indium from 310° to 595°C can be expressed as a function of temperature by the equations UIn = 1.52 x 10-3 exp sq caz per v-sec Migraion of both solutes was cathode-divected at a rate rnore than four tiMes tHAt previously found for siluer in liquid bisnmth. The electric mobilities of cadmium and indiulrz in liquid bismuth at 500° C are nearly identical with their respective mobilities in mercury at room temperature. AS part of a systematic study of the variables which are considered to control electromigration in liquid metals, the electromigration rates of cadmium and indium in liquid bismuth have been measured. Mass transport properties of silver in liquid bismuth have been reported previously,&apos; and measurements of tin and antimony in liquid bismuth are forthcoming. Comparisons will be made with literature values for these same solutes in mercury.2&apos;3 This series of solutes was selected to determine the effect of the solute valence on its electromigration. Silver, cadmium, indium, tin, and antimony have nearly equal atomic masses but have chemical valences ranging from +1 to +5. They are all fairly soluble in bismuth above 300°C and all have radioactive isotopes, which are an aid in making analyses. EXPERIMENTAL TECHNIQUE Electromigration of cadmium and indium in liquid bismuth was measured by the modified capillary-reservoir technique previously described.&apos; In this method irradiated cadmium or indium is added to bismuth to form alloys containing about 1 wt pct solute (<2 at. pct solute). Several quartz or Pyrex capillaries: 1 mm ID and 5 cm long, vertically oriented, are simultaneously filled in the reservoir of the liquid alloy. A direct current is passed through two of the capillaries, which contain tungsten electrodes sealed in the upper end. The other capillaries sample the reservoir during the experiment. After a measured time interval the capillaries are removed from the reservoir and rapidly cooled. The glass is then broken away from the solidi- fied alloy, which is then weighed, dissolved in acid, and analyzed for solute content by chemical and radiochem-ical techniques. An electric mobility (velocity per unit field) can be calculated from the amount of solute entering or leaving each capillary by the simplified expression1 in which Ui is the electric mobility of the solute, ?mi the solute weight change, Ci the solute concentration of the reservoir, I the current, p the alloy resistivity, and l the duration of the experiment. This expression is valid as long as the experiment is terminated before a concentration gradient develops across the capillary orifice. Earlier experiments showed that the concentration gradient formed initially at the electrode changes with time and eventually reaches the orifice, due to back-diffusion. This condition produces a solute exchange between capillary and reservoir by diffusion or convection, opposing the electromigration, which results in a lower measured value for the electric mobility. To determine if the concentration gradient had reached the orifice, the capillaries used in some of the experiments were sectioned at 1-cm intervals and the solute content of the alloy from each section was radiochemically determined. A typical concentration profile for an experiment with indium in bismuth is shown in Fig. 1; cadmium in bismuth showed similar behavior. As illustrated in the graph, very little back-diffusion has occurred in the capillary containing the cathode, since the concentration gradient is confined to the upper 1 cm of the capillary. In the capillary containing the anode, however, the concentration gradient is much broader, extending nearly to the orifice, even though the net change in solute concentration is nearlv the same in both capillaries. Since cadmium and indium probably lower the density of bismuth when alloyed, depletion of the solute from the alloy adjacent to the anode would increase the density of the liquid in the uppermost region of the capillary. This would give rise to convective mixing within the capillary, causing the broadened concentration gradient. Conversely, the alloy adjacent to the cathode should have a reduced density as the solute concentration is increased by migration, explaining the "normal" concentration profiles found in these capillaries. This disparity was not found for electromigration of silver in bismuth. Both metals have similar densities at the operating temperatures, and nearly symmetrical concentration profiles were found in the two capillaries of each exueriment. This density effect was also apparently encountered when an attempt was made to measure diffusion coefficients for indium in liquid bismuth by the same technique which was successfully used to measure diffusion of silver in bismuth.&apos; Capillaries 1 mm ID and 2 cm

Jan 1, 1968

By P More

US 4,132,621-In the electrowinning of aluminum, the cells are aligned in a lengthwise direction so as to lessen the harmful influence of the induced magnetic fields Each cell is supplied with current from the preceding cell both via the head arid at least one side riser The output of the cathode bars is divided into two separate groups, the upstream group supplying the head of the subsequent cell arid the downstream group supplying the side risers of the subsequent cell This produces a substantial improvement in cell efficiency arid a greater regularity P Morel, J P Dugois, arid B Langon, assigned to Aluminium Pechiney. Jan 2, 1979 12 pp. (204¬243M) Filed 1-12-78 (868,861) Priority: France, 1-19-77 (77/2,213) US 4,134,806-Cells, anodes, arid methods for use in the electrowinning of nickel, cobalt, copper, zinc, or other metals from an acid ore leach solution or the like The cell is provided with vertically immersed stationary cathodes and stationary rod anodes which are noncorrodible by the electrolyte arid are electrocatalytic to the anode reaction. The spaced parallel anode rods are connected to electric current supply bars The anode rods have an electroconductive core made of a metal alloy arid a surface coating of an oxide of platinum or a platinum group metal The ratio of active cathode surface area to active anode surface area is preferably at least 3 0. De Nora arid C Traini, assigned to Diamond Shamrock Tech¬nologies, SA Jan 16, 1979 13 pp. (204-105R) Filed 9-15-77 (833,661) Priority Italy, 1-29-73 (19738 A/73). Same British 1,434,334-5, dated May 5, 1976 US 4,135,994-In the electrowinning of aluminum at a high current efficiency, the electrolytic bath is a mixed molten salt consisting of 2-15% by weight of aluminum trichloride, 15-83% of sodium chloride, 15-70% of combined calcium chloride arid magnesium chloride but riot more than 40% of calcium chloride, arid optionally up to 10% of barium chloride Preferably, plate-shaped graphite electrodes used for both cathodes and anodes are arranged in parallel inclined relation so that the axis in the lengthwise direction makes an angle of from 10° to 45° to the horizontal. T Ishikawa arid H Ichikawa, assigned to Nippon Light Metal Co Ltd Jan 23, 1979 4 pp (204-67) Filed 11-15-77(851,632) Same British 1,550,502, dated Aug 15, 1979

Jan 1, 1980

By J. F. Enrietto

Internal friction measurements were used to determine the effect of manganese on the solubility and precipitation kinetics of nitrogen. Manganese, in concentrations up to 0.75 pct, has little effect on the solubility at temperatures above 250°C. On the other hand, at Concentrations as low as 0.15 pct, manganese inhibits the formation of iron nitrides, especially Fe4N, even though it may not form a precipitnte itself. The precipitation and solubility of carbides and nitrides have been extensively investigated in the pure Fe-C and Fe-N systems.1-3 In recent years, some effort has been ispent in studying the influence of substitutional alloying elements on the behavior of carbon and nitrogen in ferrite.4 -7 In particular Fast, Dijkstra, and Sladek have investigated the effect of 0.5 pct Mn on the internal friction and hardness during the quench aging of Fe-Mn-N alloys.&apos;, &apos; They found that at low temperatures (below 200°C) the presence of 0.5 pct Mn greatly retarded quench aging. For example, after 66 hr at 200°C very little precipitation had taken place in the iron alloyed with manganese, whereas precipitation was complete after a few minutes in a pure Fe-N alloy. The effect of varying the manganese content and the details of the precipitation process were not mentioned in these papers. Fast&apos; postulated that manganese causes a local lowering of the free energy of the lattice with a resulting segregation of nitrogen atoms to these low energy sites. The segregated nitrogen atoms are bound so tightly to the manganese atoms that they cannot form a precipitate. The internal friction measurements of Dijkstra and Sladek tended to confirm the concept of segregation of nitrogen around manganese atoms, and the increase in free energy on transferring a mole of nitrogen atoms from a segregated to a "normal" lattice site was computed to be - 2800 cal. Dijkstra and Sladek9 distinguished between two types of precipitates: ortho, a nitride of appreciably different manganese content than that of the matrix, and para, a nitride with a manganese content essentially that of the matrix. With each type of precipitate a solubility, again designated ortho or para, can be associated. Since the internal friction maximum in alloys which were aged several hours at 600" C dropped almost to zero, Dijkstra and Sladek9 concluded that the ortho solubility must be very low. The effect of temperature on the ortho and para solubilities has no1: been investigated. There are obviously several gaps in our knowledge concerning the influence of manganese on the behavior of nitrogen in a-iron. It was the purpose of the experiments described in this paper to determine the following: 1) The ortho and para solubilities of nitrogen as a function of temperature. 2) The details of the precipitation process at elevated temperatures. 3) The effect of varying the manganese concentration on the above phenomena. EXPERIMENTAL PROCEDURE Internal friction is conveniently employed in studying the precipitation of nitrides and/or carbides from a -iron because it is one of the few parameters, perhaps the only one, which is not affected by the presence of the precipitate itself. For this reason, internal friction techniques were heavily relied upon in the present experiment. A) Preparat of -. All specimens were prepared from electrolytic iron and electrolytic manganese. Alloys containing 0.15, 0.33, 0.65, and 0.75 wt pct Mn were vacuum melted and cast into 25 lb ingots. After being hot rolled to 3/4 in. bars, the ingots were swaged and drawn to 0.030 in. wires. The wires wen? decarburized and denitrided by annealing at 750° C for 17 hr in flowing hydrogen saturated with warer vapor. To obtain a medium grain size, - 0.1 mm, the wires were then heated to 945oC, allowed to soak for 1 hr, furnace cooled to 750°C, and water quenched. Subsequent internal friction measurements showed that this procedure reduced the nitrogen and carbon concentrations of the alloys to less than 0.001 wt pct. The wires were nitrided by sealing them in pyrex capsules containing anhydrous ammonia and annealing them for 24 hr at 580°C, the nitrogen being retained in solid solution by quenching the capsule into water. Immediately after quenching, the wires were stored in liquid nitrogen to prevent any precipitation of nitrides. By varying the pressure of ammonia in the capsule, it was possible to produce any desired nitrogen concentration. B) Internal Friction. The internal Friction measurements were made on a torsional pendulum of the Ke type,&apos;&apos; a frequency OF 1. or 2 cps being used. For

Jan 1, 1962

By A. S. Yue

The movphology of the Mg-32 wt pct Al eutectic has been studied as a function of freezing- rate and temperature gradient. At slow freezing rates a lamellar eutectic was formed; whereas, a rod-like eutectic was generated at fast rates. The inter-lamellar spacing increased as the freezing rate decreased in aggreement with theoretical predictions. Lamellar faults, morphologically similar to edge dislocation models in crystals, were responsible for the subgrain structures in the eutectic mixture. A linear increase in fault density with freezing rate was observed. Fault concentl-ations of the order of 10 per sq cm for a range of freezing rates from 0.6 to -3.0 x 10 cm per sec were estimated. The transformation from lamella?, to rod-like morphologies was determined experimentally to be dependent on the freezing rate and independent of the temperature gradient. Moreover, the number of rods formed per- unit cross-sectional area increased exponentiallv with increasing freezing rote. BRADY&apos; and portevin2 classified eutectic structures into lamellar, rod-like, and globular according to the morphology of the solid phases present. Although this classification is quite descriptive, very little has been reported on the details of the mechanism by which the eutectic structures are formed. Recent work by Winegard, Majka, Thall, and chalmers3 and by chalmers4 on lamellar eutectic solidification suggest that the maximum thickness of the lamellae decreases with increasing rate of solidification due to inadequate time for lateral diffusion. scheilS and Tiller&apos; have shown theoretically that the lamellar widths indeed depend on the solidification rate. However, there has been no experimental evidence to support the theory. Chilten and winegard7 have studied the interface morphology of a eutectic alloy of zone-refined lead and tin. They found that the lamellar width decreased as the freezing rate increased in agreement with the theoretical predictions of scheils and Tiller.&apos; More recently, Kraft and Albright&apos; have investigated the microstructures of the A1-CuA12 eutectic as a function of growth variables. They observed lamellar faults present in the lamellar eutectic, similar to edge dislocation models in crystals. Furthermore, Kraft and Albright reported that they could not designate which extra lamellar was responsible for the formation of a lamellar fault even under electron microscopic magnification. In this paper, the morphology of the Mg-A1 eutectic structure is described. The effects of freez- ing rate on the interlamellar spacing and on the lamellar fault density are presented in detail. The transformation from lamellar to rod-like eutectics is discussed in terms of the freezing rate and the temperature gradient. EXPERIMENTAL PROCEDURE The experimental details of alloy preparation, the decanting mechanism and the determinations of the freezing rate and the temperature gradient have been reported elsewhere. Measurements of plate-edge angles were made with a microscope. The true angles used to determine the interlamellar spacings were determined by a two surface analysis technique.&apos;&apos; Since the decanted interface structure does not represent the true eutectic morphology on the solid,g all measurements were made from an area in the solidified bar behind the interface. Measurements of the apparent interlamellar spacings between the two phases of the eutectic were made on a photographic negative by means of a calibrated magnifier. Each value listed in Table I represents the average of thirty measurements on one negative. In general, these measurements are approximately equal with an error of less than pct. The average rod diameter for each specimen was also measured on a magnified photomicrograph. Each value of the diameter represents the average of fifty measurements. RESULTS AND DISCUSSION The experimental observations and their discussion to be presented here are restricted to the morphology of the eutectic structure and to the effects of the freezing rate and the temperature gradient on the solidification of eutectics. INTERLAMELLAR SPACING It has been shown previouslyg that the micro-structure of the decanted interface and the longitudinal section of the Mg-A1 eutectic is characterized by the presence of both lamellar and rod-like morphologies. The lamellae become more regular as the freezing rate is decreased. A three-dimensional photomicrograph representing a perfect lamellar morphology is illustrated in Fig. 1. The lamellae of the top and longitudinal sections of the specimen are regularly spaced while those in the transverse section are not quite straight and parallel. Their parallelism is slightly distorted because fault lines producing a discontinuity are present. A method for calculating the interlamellar spacings A, is described in Appendix 1. The true

Jan 1, 1962

By K. E. J. Rapperport, C. S. Hartley

The only slip system observed in zirconium crystals deformed at 77", 575", and 1075OK was (1010) [1210] with a critical resolved shear stress in tension of 1.0 kg per sq mm at 77°K; 0.2 kg per sq mm at 575 °K; and 0.02 kg per sq mm at 1075 OK. The active twin planes were {1012}, (1121}, (11221, and (11233) with varying temperature dependence. A detailed analysis for the slip direction using Laue spot asterism is appended. NeARLY all metals of the hexagonal close-packed structure exhibit basal slip, i. e.,(0002)<1120>- type slip. This is true of magnesium,&apos; zinc,&apos; cadmium,3 beryllium,4 titanium,= yttrium,6 and rhenium.Many of these such as titanium 5&apos;8-&apos;0beryllium,4&apos;" magnesium, and zinc13&apos;14 display other slip modes even at room temperature, and nearly all have been reported to slip on other systems under particular loading or temperature conditions of testing. As is shown in this paper, basal slip was not found at any of four test temperatures from 77" to 1075°K in hexagonal close-packed zirconium under the simple loading conditions of tension and compression, even though in one case the resolved shear stress on the inactive (0002) <llgO> system was twenty-five times higher than the critical resolved shear stress on the active (1010) [1210] system. This result is consistent with prior studies on the active deformation processes in zirconium deformed at room temperature. &apos;&apos;-I7 SPECIMEN PREPARATION A) Material—The zirconium used in this work was of two types: 1) as-deposited reactor grade crystal-bar, and 2) arc-melted and forged reactor grade crystal-bar. Typical chemical and spectrographic analyses of these materials as received, and after hydrogen removal and crystal growth are given in Ref. 17. Crystals of type 1) above have the letter prefix (A) and those of type 2) have the prefix (B) throughout this paper. B) Crystal Growth— he zirconium was machined into rectangular parallelepipeds about 0.2-in. scl in cross section and 2 in. iong. These were hand polished through 4/0 abrasive paper, electropolished, given a hydrogen removal anneal, and subjected to long-time anneals at 840 °C in vacuo to produce usable crystals.&apos;7 A second technique used to obtain large crystals was to cycle the samples two or three times between 1200" and 840°C, allowing them to remain at the higher temperature for about 4 hr and at the lower temperature for 5 days.17 These techniques yielded some grains which occupied the entire cross section of the bar and were as long as 3/4 in. C) Orientation Determination—After the growth of large crystals by thermal cycling, the samples were repolished with extreme care through 4/0 abrasive paper and electropolished. Metallographic examination after polishing showed the surfaces to be free of visible deformation traces. Standard Laue back-reflection X-ray techniques were used to find the crystallographic orientations of selected large grains with respect to a specimen face and edge. Fig. 1 shows the stereographic projections of the stress axes for the crystals used. The sharpness of the spots on the Laue photographs indicated that the crystals were of good quality. EXPERIMENTAL METHODS Nine crystals were deformed in tension at 77"K, nine in tension and five in compression at 300°K in previous tests,17 fifteen in tension at 575"K, and eleven in tension at 1075°K. All specimens were stressed by load increments. After a predetermined load was applied, the specimen was removed from the loading appratus and metallographically examined for deformation traces. An attempt was made to initially stress each bar so that some crystals slipped a small amount and others not at all. This was done to bracket the critical resolved shear stress. One bar of special orientation (B-11) was repolished and annealed at 1075°K for 1 hr after lower temperature deformation, before final deformation at 1075°K. In the other bars the loading by increments, followed by metallographic examination, was continued until the surface distortion would interfere with analysis, or until fracture. One example of a crystal pulled to fracture is shown in Fig. 2. This photograph shows a crystal (B-14C) which was pulled at 1075°K and failed by slip on two (10i0) planes. The approximate orientation of this crystal is illustrated in the figure. Specimens were deformed at 77°K in liquid nitrogen on a tensile machine using an insulated bucket with an internal hook to accept a clamped specimen.

Jan 1, 1961