Search Documents

By N. E. Garner

Laboratory experiments were conducted to investigate the cutting of a single diamond on limestone and shale under simulated down-hole conditions. A high-pressure chamber was modified by adding a rock-rotating device so that planing tests could be run. Weight on the diamond, diamond geometry and differential pressure across the face of the rock were varied. It was found that (I) high differential pressure reduced the volume of rock cut by the diamond at a given bit weight by strengthening the rock and changing the mode of failure; (2) a finely powdered rock left in the bottom of the grooves reduced the volume cut by as much as 50 percent; and (3) orientation of a single diamond about the axis of a drill point had considerable influence on diamond cutting efficiency. INTRODUCTION Diamond bits consist of many diamonds held in a matrix provided with water courses for fluid passage to clean, cool and lubricate the diamonds as they drill formation. Each diamond contributes its share to the overall effectiveness of a bit, but a lack of understanding of the performance of a single diamond has hampered efforts to engineer improvements in diamond bits. The need for those improvements prompted this study. This paper describes the findings of a laboratory investigation of the outting action of a single diamond where the differential pressure between the wdlbore and formation, diamond geometry and vertical force on the diamond were independently varied. The tests were conducted in a pressure chamber that provided relative horizontal motion (planing) between a rock and diamond under simulated down-hole pressure conditions. EQUIPMENT HIGH-PRESSURE CHAMBER WITH ROTATING DEVICE The high-pressure chamber used in previous rock mechanics studies' was modified for this study by addition of a rock-rotating device. The modified chamber (Fig. 1) differs from the old chamber in that the rock can be rotated to provide relative horizontal movement between the rock and the penetrator which may be a small element of a diamond or a drag bit. In this study the penetrator was a single diamond. The rock sample holder inside the chamber is mounted on a thrust bearing and is connected to the external drive mechanism by a stem that passes through two seal elements. The seal elements are needed to allow formation pressure to enter the bottom of the rock sample through a small hole in the stem. The Kapseal seal elements (Tefion boots backed by O-rings) provide low friction (hand free) even at differentials of 5,000 psi. The drive mechanism is a variable-speed transmission with a speed range from 0 to 30 rpm and an output torque of 2,800 in.-lb. A right-angle-drive gear box couples the drive to the stem. The new design has two independent pressure systems (formation and borehole) to simulate down-hole rock stress environment. Formation pressure enters from the bottom of the rock through a 6-in. diameter area, and borehole pressure acts over the remaining surface. A 14-in. layer of zero fluid loss oil-base mud poured over the top of the rock and an O-ring seal on bottom allow a differential between the borehole and formation pressures. Bayol 50 was used as the hydraulic fluid in the chamber. The differentials reported here were obtained by elevating the borehole pressure while keeping the formation pressure at zero.

By D. R. Hay, E. Scala

STUDIES of structure-sensitive properties, especially mechanical behavior, have shown that grain and subgrain structure play an important role. The mechanical properties of tungsten, in particular, are sensitive to the nature of the intergranular structure. Substructure and dislocation networks in single-crystal and polycrystalline tungsten have been studied by Nakayama et al.' Various orders of substructure were observed ranging from a microscopic first order (grain diameter: 2 to 8 mm) to a microscopic second order (grain diameter: 50 to 300 p), and, within the latter, dislocation networks forming an even smaller order of substructure. In their single crystals, grown by arc fusion, the degree of misorientation in each order was small: 16'3OU, -11, and -10" for the first-, second-, and third-order substructure, respectively. To study the properties of polycrystalline tungsten, powder metallurgy tungsten is generally used. However, in a mechanical property investigation, the zone-melted or arc-fusion crystals are more desirable than the powder metallurgy product due to their higher purity and absence of porosity and other defects inherent in consolidation by powder metallurgy. Grain boundaries can also be produced in melted stock by working and recrystallizing. However, material with subgrain mis orientations of the order of several degrees (high-angle substructure) has not been reported previously and is the subject of this communication. Crystals were grown by electron-beam, floating-zone melting. The starting material, Sylvania Pure-tung welding rod, was given one zone pass at a traversal rate of -2 mm per min. Through control of the zone temperature, it was possible to influence the degree of crystal perfection. By maintaining the zone at a high degree of superheat, high-perfection crystals could be grown. However, at temperatures only slightly above the melting point, the zone-melted crystals contained a high-angle substructure. A sensitive control of the zone temperature was not possible due to the difficulty of estimating the temperature of the zone and of providing a constant supply of power to the sample. Therefore, an empirical method, using the shape of the molten zone as a criterion, was adopted as an indication of temperature. At high degrees of superheat, the surface tension of the molten zone decreases and a neck forms at the top of the zone, whereas at low zone temperatures the diameter of the zone remains reasonably uniform. Although it was not possible to obtain a continuous variation of misfit angle, the conditions could be directed toward the growth of either high- or low-angle substructure by maintaining only a slight neck in the zone (sufficient to establish that it was molten) or a well-necked zone, respectively. Mass spectrographic analyses of both types of material revealed no significant differences in the concentrations of their impurities. The degree of misorientation at high angles was obtained by measuring the angular spread of spots corresponding to a single reflection on a Laue back-reflection photograph. Fig. 1 shows a typical Laue back-reflection photograph of a crystal with a 3-deg spread. By measuring the angular deviation of the spots corresponding to a single reflection from the mean center of the spots around which constant angular deviation contours were drawn, an average angular spread of misfit could be calculated. The angular average was weighted by the number of spots observed in each angular interval. At angles greater than 5 to 6 deg the spots from different reflections begin to overlap, and cannot be associated with a particular reflection. Laue back-reflection photographs taken at different locations on samples .with approximately 3-deg spreads showed only a small difference in angular misorientation, less than 8' of arc, within individual specimens. The microstructure was examined using Berg-Barrett X-ray extinction contrast microscopy. Berg-Barrett photographs taken directly on the as-grown surface, Fig. 2, show an essentially equiaxed subgrain structure of -0.1 mm in average grain diameter in both high- and low-angle crystals. Fig. 2(a) is a photograph of a sample with a low misfit angle and Fig.

Jan 1, 1968

By S. C. Sun

With the aid of emulsifiers, intense high-frequency sound waves are capable of emulsifying any collector in water. The data show also that ultrasonically emulsified collectors are more effective in floating minerals than the nonemulsified collectors. THE use of ultrasonics in forming emulsions is not new. As early as 1927 Wood and Loomis reported preparation of emulsions with ultrasonics. In 1935 Rschevkin and OstrawskyV escribed the use of great ultrasonic power in producing fine emulsions of various oils and paraffin in water. Recently Oyama and Tanaka3 employed ultra-emulsification to increase the effectiveness of sodium ethyl xanthate in flotation of chalcopyrite and galena. An emulsion is a two-phase system consisting of two incompletely miscible liquids, the one being dispersed as finite droplets In the other. The dispersed liquld is known as the internal or discontinuous phase, and the surrounding liquid is termed the external or continuous phase. There are two types of emulsions; one is oil-in-water (O/W) and the other water-in-oil (W/O). The word oil refers to the liquid other than water. Circumstances exist in which the emulsion type is not clearly defined, and the internal and external phases both contain portions of the opposite phase. This is said to be a dual emulsion. Among the many hypotheses, 5a, B proposed for the formation of emulsions, the Bancroft's adsorbed film or double interfacial tension theory is widely accepted. Bancroft 7, 8 deduced that in the process of emulsification the interfacial tension between oil and water is lowered by the formation of an emulsifying film, which contains the adsorbed molecules and/or ions from the emulsifying agent and the two liquids. This film has two interfacial tensions, one with the water and the other with the oil, which are not necessarily equal. The difference in interfacial tension between the two surfaces of the film is chiefly responsible for forming different types of emulsions. For example, if the interfacial tension between water and film is less than that between oil and film, the film will become convex on the water side, thereby tending to form an oil-in-water emulsion. On the other hand, if the interfacial tension between water and film is greater than that between oil and film, the film will become concave on the water side, thereby tending to make a water-in-oil emulsion. In line with this theory, emulsifying agents soluble in water have the tendency to form oil-in-water emulsions, while those soluble in oil form emulsions of the reverse type. Apparatus and Experimental Procedure: The ultrasonic apparatus shown in Fig. 1 consisted of a hypersonic generator (A), Brush Development Co. model Bu-204; a hypersonic transducer bowl (B) whose resonant frequency is 400 kc per sec; and a round-bottomed glass tube (C) of 2.2 cm ID and 21 cm in length. The acoustical output power of the hypersonic transducer bowl was standardized with a Hewlett Packard vacuum tube voltmeter, model 41 0B, across the hypersonic generator output. The glass tube, containing the materials to be emulsified, was placed 1 cm above the central surface of the transducer bowl, which was filled with water as shown in Fig. 2. Ultrasonic emulsification was performed in three steps, although a one-step method has been used: 1) emulsifying the predetermined amounts of col-

Jan 1, 1956

By Ralph Hultgren

IN solid solutions atoms of differing sizes occupy the same crystalline lattice, requiring that some of them be compressed and others expanded. The energy involved has been called misfit strain energy and is an important concept of crystal chemistry. If the atomic sizes and elastic constants of interatomic bonds are known, the misfit energy may be calculated,' provided certain simplifying assumptions are allowable. Usually, isotropic crystals are assumed and interatomic distances are taken to be the statistical average determined from X-ray diffraction. Such calculations yield values of the misfit energy of the order of 1 or 2 kcal per atom in alloys such as Au-Cu at compositions of 50 atomic pct. However, evidence has accumulated in recent times that atoms change their sizes with composition of alloys, implying electronic rearrangement of the bonds. The size changes have been found particularly by application of the X-ray method developed by Warren, Averbach, and Roberts.' Thus, Averbach, Flinn, and Cohen3 determined radii in Au-Cu alloys. Oriani4 showed that these new radii led to a calculated misfit energy in disordered AuCu, which was decreased from the values calculated by the usual theory more than twenty-fold, to only 80 cal per g atom. Thermodynamic calculations from the phase diagram5 also show misfit energy to be no more than a few hundred calories per g atom in this alloy. The question of what electronic rearrangements are possible therefore becomes compelling in estimating misfit energy. In the following pages the results of certain calculations on the AuCu tetragonal superlattice are submitted. Conclusions drawn from these should be applicable in large degree to disordered solid solutions. As in all ordered states, bonding distances in the superlattice are individually known, rather than being merely average distances as found from lattice constants of disordered states. Moreover, only the Au-Au and Cu-Cu distances are strained; the elastic constants of these are known in the elementary state. In the usual calculation it is necessary to assume elastic constants for Au-Cu bonds. Misfit energy has thus been calculable without the need of many simplifying assumptions usually made. It is still assumed that equilibrium bond lengths and elastic properties of the bonds are the same in the alloy as in the pure metals. As previously discussed, this is probably not correct. Also assumed is that the bonds are not affected by strain of neighboring bonds. A calculation of Young's modulus from compressibility data shows this to be far from true; extensive electronic rearrangements take place. It would seem that misfit energy cannot be calculated from elasticity data for the elements. The usual methods may, however, give an upper limit which is often much higher than the true value. The question of electronic rearrangement is, of course, a complex one. Pauling's theory gives a simple, approximate treatment of the relation between type of bond and bond distance. This has been applied with some success to the Au-Cu system, as will be shown in a later section. Misfit Energy in Au-Cu Alloys Hume-Rothery and Raynor6 discuss the Au-CU system as a type example of strain energy. The gold atom is 12.8 pct larger in diameter than the copper atom, near the size factor limit beyond which solid solubility is severely restricted. They therefore consider the misfit energy to be large, a conclusion for which they believe they find evidence in the phase diagram. Gold and copper are completely miscible in the solid state, but the alloy has a minimum melting point at an intermediate composition. From this Hume-Rothery and Raynor conclude that the strain energy is nearly large enough to prevent miscibility; the phase diagram tends toward a eutec-tic type. In Ag-Cu, which has almost identical size relationships, solid miscibility is quite limited; whereas in Au-Ag, where atomic sizes are nearly the same, there is complete miscibility without a minimum in the melting point. From their arguments the heat of formation of Au-Cu would be expected to be endothermic or only slightly exothermic, that of Ag-Cu to be endothermic, and that of Au-Ag to be exothermic. Deviations, from Ve-gard's law of additivity of atomic radii support these conclusions, since Au-Cu and Ag-Cu both have pronounced positive deviations, and Au-Ag has a negative deviation. Nevertheless, Au-Cu alloys form exothermically; indeed, considerably more exothermically than Au-Ag, Table I. Hence, strain energy must be much less important in this case than Hume-Rothery and Raynor have supposed.

Jan 1, 1958

By Irving B. Cadoff, Alvin A. Machonis

The resistivity, Hall coefficient, Seebeck coefficient, and thermal conductivity were measured as a function of temperature for cation-rich alloy single crystals covering the composition range across the PbTe-SnTe system. Alloying of PbTe with up to 20 pct SnTe was found to have little effect on the energy gap. Above 20 pct SnTe the alloys were "p" type but below this range the sign could be varied by heat treatment. The lattice thermal resistivity of the compounds SnTe and PbTe is raised by alloying one with the other. Z values in the order the interesting values obtained. THE PbTe-SnTe system has several interesting features. For one, PbTe is a useful thermoelectric material and the possibility of improving its figure of merit by alloying with SnTe, an isomorphous compound, has been suggested since these pseudo-binary solid solutions generally have a more favorable ratio of electrical conductivity to thermal conductivity than either of the components.' Other interesting features relate to the conductivity mechanism, band structure, and stoichiometry of the compounds and their alloys. PbTe is a semiconductor with an energy gap of about 0.29 ev2 at room temperature whose conductivity sign and magnitude can be varied from "n" to "p" by controlling the proportion of lead and tellurium with respect to the stoichiometric ratio.3 Excess lead results in "n"-type conduction. SnTe is found to exist only as a "p"-type material of relatively high conductivity. This behavior is attributed to stoichiometric deviation by Brebrick4 but Sagar and Miller proposed that the behavior of SnTe must be due in part to the presence of an overlapped band. An investigation of alloys of this system, therefore, might give additional information which would permit one to evaluate which of the two proposals is the more appropriate one. Abrikosov et al.' studied the room-temperature electrical properties of these alloys and reported data for Seebeck coefficient and resistivity on poly-crystalline alloys. The present work is a more exhaustive survey of the PbTe-SnTe system. Re- sistivity, Hall coefficient, Seebeck coefficient, and thermal conductivity were measured over a wide temperature range for single crystals at 10-pct intervals of lead/tin ratio across the pseudobinary system. The relative concentration of tellurium was controlled so as to obtain metal-ion excesses in all cases. SAMPLE PREPARATION The crystals were prepared by melting elemental lead, tin, and tellurium in weighed proportions in evacuated Vycor capsules. The lead and tellurium were high-purity grades obtained from American Smelting & Refining Co. The tin was supplied by Comico. The proper calculated proportions of lead, tin, and tellurium were weighed and charged into prepared Vycor capsules prior to evacuation. The capsules were prepared from 15-mm Vycor tubing. A sharp point was worked on one end of the tube. A pyrolytic graphite coating was deposited on the Vycor walls by heating the tip to 800°C in an atmosphere of acetone-saturated argon. An additional coating of graphite was deposited on the pyrolytic coating from an Aquadag suspension. Above the coated tip the tube was reduced in diameter to form a constrictive neck. To avoid scratching the graphite coatings the charge was placed in the tube above the constriction. After a low-temperature bake, the evacuated capsule was sealed. On subsequent heating the charge melted down into the lower portion of the capsule. The crystals were grown by lowering the capsule through a Bridgman-Stockbarger furnace. The lowering rate was 1 in. per 8 hr. The upper portion of the furnace was set for 950°C and the lower portion for 800°C. In general the yield of single crystals was about 25 pct. The mixed compositions were, as expected, the most difficult to grow. The finished crystals were sectioned into 5/8-in. slices. The tip, end, and middle slices from each crystal were analyzed by X-ray fluorescence to determine the lead-to-tin ratio. The resulting values were used to plot a composition vs distance plot for each crystal. Slices were selected from each crystal, with the aid of the composition plots, to cover the complete range of compositions at 10-pct intervals. In general, the slices selected were taken from the seed end of the crystal where the longitudinal segregation (as determined from the X-ray fluorescence analysis) was a minimum. Laue single-crystal analysis and metallographic analysis was used to verify if a slice was single or polycrystal. Any grain boundaries were clearly visible in the as-cut and polished condition. In ad-

Jan 1, 1964

By E. H. Rose

IN these days of the spectacular in research and technological accomplishment, it is easy and natural to overlook some of the applications to everyday life of recent developments of a more pedestrian kind, or to fail to realize that sometimes two or three of the latter may be combined to serve a novel purpose in fields other than those in which they grew. The present remarks are to point out three such developments which might be combined to apply to an everyday function of the A.I.M.E. as an organization. By its Constitution, the A.I.M.E. is organized "to promote the arts and sciences connected with . . . minerals and metals, and the welfare of those employed in these industries . . .; to hold meetings for social intercourse and the reading and discussion of professional papers, and to circulate . . . among its members the information thus obtained . . .; and to . . . maintain . . . a library." By these words of Article I the profession of mining and metallurgy is recognized to involve many arts and sciences, of which the art and science of exchanging information is a leading one. As to methods of preparing or securing papers, the Constitution is silent.

Jan 1, 1944

By John T. Galey

A combination of two factors in addition to the current Federal drilling and price regulations reduced by 120 from I942 the number of new wells completed in southwestern Pennsylvania during the year. No new prospective area was found comparable to the Armbrust gas pool, Westmoreland Co., which accounted for a seventh of the last year's drilling, and it is considered doubtful whether, even if such a field had been discovered, the drilling contractors, who have been seriously affected by the manpower shortage, could have drilled many more wells than they did during the year. New wells totaling 445 were completed for a combined footage of over 1,250,000 Dry holes numbered 131 and had a footage of nearly 400,000. Old wells drilled deeper total 55, of which 17 were found nonproductive. Shallow Development Oil Oil completions yielded an initial of only slightly over one hundred barrels from 21 wells for about the same per well average as that of a year ago. However, 65 bbl. of this total came from two wells in two new strikes. The footage drilled of nearly 33,000 gives an average of nearly I00 ft. less per well than a year ago. Two old wells drilled deeper had a combined initial of only 4 bbl. The largest oil well of the year, 40 bbl., was found in the Speechley (U. Dev.) sand at a depth of 3492 ft. in German township, Fayette County. The location is several miles east of the nearest oil production hut as the area that could be occupied by a pool is fairly well delimited by drilling, the extent of this production would not appear to be large. The other notable oil production was found in the Dunkard (Penna.) sand, Cumberland township, Greene County, at a depth of 1065 ft. Here the first well had an initial of g bbl. and the second 25 bbl. However, a third proved dry, and as this area is also delimited by drilling, the pool doubtless will be of small area. Gas Gas completions yielded an initial of slightly over one hundred million cubic feet per day and new wells, totaling 303, account for all but four million of this volume. Old wells drilled deeper, numbering 35, found gas. The per well average in new drilling of approximately 320 M cu. ft. is nearly 165 M cu. ft. less than a year ago and the total footage is slightly over 830,000, which is about a quarter of a million feet less than in 1942. Average rock pressure of new completions is approximately 365 lb. per sq. in. The entire volume of new production is from the Upper Devonian or higher stratigraphic horizons. In Allegheny County, the grestest activity was in Forward and Plum townships. Wells there account for more than one half the completions. One large well was drilled in Forward township and an open flow of 3.623 million cubic feet was found in an old Gantz (U. Dev.) sand area. The top of the sand was encountered

Jan 1, 1944

By John T. Galey

A combination of two factors in addition to the current Federal drilling and price regulations reduced by 120 from I942 the number of new wells completed in southwestern Pennsylvania during the year. No new prospective area was found comparable to the Armbrust gas pool, Westmoreland Co., which accounted for a seventh of the last year's drilling, and it is considered doubtful whether, even if such a field had been discovered, the drilling contractors, who have been seriously affected by the manpower shortage, could have drilled many more wells than they did during the year. New wells totaling 445 were completed for a combined footage of over 1,250,000 Dry holes numbered 131 and had a footage of nearly 400,000. Old wells drilled deeper total 55, of which 17 were found nonproductive. Shallow Development Oil Oil completions yielded an initial of only slightly over one hundred barrels from 21 wells for about the same per well average as that of a year ago. However, 65 bbl. of this total came from two wells in two new strikes. The footage drilled of nearly 33,000 gives an average of nearly I00 ft. less per well than a year ago. Two old wells drilled deeper had a combined initial of only 4 bbl. The largest oil well of the year, 40 bbl., was found in the Speechley (U. Dev.) sand at a depth of 3492 ft. in German township, Fayette County. The location is several miles east of the nearest oil production hut as the area that could be occupied by a pool is fairly well delimited by drilling, the extent of this production would not appear to be large. The other notable oil production was found in the Dunkard (Penna.) sand, Cumberland township, Greene County, at a depth of 1065 ft. Here the first well had an initial of g bbl. and the second 25 bbl. However, a third proved dry, and as this area is also delimited by drilling, the pool doubtless will be of small area. Gas Gas completions yielded an initial of slightly over one hundred million cubic feet per day and new wells, totaling 303, account for all but four million of this volume. Old wells drilled deeper, numbering 35, found gas. The per well average in new drilling of approximately 320 M cu. ft. is nearly 165 M cu. ft. less than a year ago and the total footage is slightly over 830,000, which is about a quarter of a million feet less than in 1942. Average rock pressure of new completions is approximately 365 lb. per sq. in. The entire volume of new production is from the Upper Devonian or higher stratigraphic horizons. In Allegheny County, the grestest activity was in Forward and Plum townships. Wells there account for more than one half the completions. One large well was drilled in Forward township and an open flow of 3.623 million cubic feet was found in an old Gantz (U. Dev.) sand area. The top of the sand was encountered

Jan 1, 1944

By Richard A. Sheppard

Zeolites-crystalline hydrated aluminosilicates of the alkalis and alkaline earths-are important rock-forming constituents in sedimentary rocks and are potentially valuable industrial minerals. They have a framework structure that encloses interconnected cavities occupied by the relatively large cations and water molecules. The cations, chiefly sodium, potassium, and calcium, and the water have considerable freedom of movement within the structure and give the zeolite their cation- exchange and reversible-dehydration properties. Some zeolites have essential contents of barium, strontium, or magnesium. The basic structure

Jan 1, 1975

By SIDNEY ROLLE

ACURSORY glance through the literature on the subject reveals that the ablest minds in the land are devoting themselves to the great question of labor, of which employment is one of the fundamentals. Volumes have been written and the end is not in sight. Employment management is today about in the position that efficiency was 15 years ago. During the early days of the war, and perhaps for a year or so before, labor was plentiful. As the war progressed and Europe drew on us for munitions, employers began to compete with one another for', all, classes of labor. Labor was difficult to obtain, wages rose, the labor turnover increased, and employers began to install employment departments, welfare plans, and all sorts of schemes, but the labor efficiency dropped. As the war progressed, greater and greater production was demanded. New factors were introduced each day. The government, labor unions, industrial councils, all tended, it seemed, to make the situation almost intolerable. Wages rose to fantastic heights, the cost of living rose higher and higher, and the efficiency dropped still further.

Jan 1, 1921

By George W. Sears

In preparing this symposium, our ambition was to elicit authoritative expression of opinion concerning important selected phases of the industry from men active in it. Responses to requests for contributions were gratifying, especially so in view of the short time available. The generous and cooperative spirit of the industry as a whole is amply evident. Responses were received from the following, who are therefore the true authors of the paper: W. G. Adamson, General Manager of the pershin; Quicksilver Co., Lovelock, Nev.; Dudley Baird, Vice President, Pacific Foundry Co., San Francisco; Walter W. Bradley, State Mineralogist of California; W. D. Burcham, General Manager of the Brewster Quicksilver Consolidated, Terlingua, Tex.; William Forstner, San Francisco; H. W. Gould, of H. W. Gould & Co., San Francisco; Marcus Hulings, General Manager of the Chisos Mining Co., Terlingua, Tex.; Frank J. Katz, Chief Engineer, Division Mineral Statistics, United States Bureau of Mines, Washington, D. C.; Lloyd J. Lathrap, Superintendent, Nevada Quicksilver Mines, Inc., Lovelock, Nev.; W. R. Moorehead, General Manager, New Idria Quicksilver Mings, Inc., Idria, Calif.; F. W. Oakes, Jr., Terlingua, Tex.; C. N. Schuette, San Francisco. Brief Economic History of Quicksilver in the United States Quicksilver ore was first discovered in the United States at what was later the New Almaden mine in California, in the year 1824. Production also began here, but not until 1850, when it was stimulated by the active demand caused by gold-mining operations. Prospecting for quicksilver was active, high-grade ores were found and ample production lowered the price from $100 per flask in 1850 to about half that figure for the greater part of the next 10 years. During the succeeding decade, many new quicksilver mines were found; production increased at a time when the local demand diminished, so that most of the product was exported. The third decade of quicksilver mining in the United States witnessed the development of the pan amalgamation process, particularly in Com-stock silver-mining operations. A suddenly increased demand sent prices soaring, the all-time peak of quicksilver production followed, and the highest price was soon replaced by the lowest one on record. Huge quantities of quicksilver were exported between 1870 and 1880 and exports continued in decreasing measure for three decades to 1910. In

Jan 1, 1930

Arizona ROBERT E. TALLY, Chairman CARL E. ~IILLS, Secretary-treasurer, P. 0. Box 1462, Jerome. Ariz. W. S. BOYD THOMAS H. 0. O'BRIEN F. W. MACLENNAN Boston Meets first Monday each winter month GAL~N H. CLEVENG~, Chairman HOLCOMB J. BROWN, Vice-chairman F. I,EROY FOSTER Secretary-treasurer Room 8-219, Mass. lnst: of Tech., Cambridge Mass. A. E. WELLS H. A. WENTWORTH

Jan 1, 1928

By Douglas A. Karvonen

INTRODUCTION Although the economy in the Province of Saskatchewan has historically been agriculturally oriented, a major source of wealth has been realized through natural resources such as petroleum and natural gas, coal and uranium and since the 1960's - potash. Potash or potassium chloride, in the form in which it is presently produced in Saskatchewan, is used primarily as fertilizer, a source of potassium, one of three essential elements required for healthy plant growth, with about 5% of production sold to the chemical industry for use in such products as soap and liquid detergent, glass and ceramics, textiles and some pharmaceuticals. Saskatchewan is estimated to have approximately 40% of known world potash reserves and its ten active mines account for some 25% of annual world production. POTASH CORPORATION OF SASKATCHEWAN In an effort to guarantee a fair and lasting economic benefit to the Province of Saskatchewan, the Potash Corporation of Saskatchewan (PCS) was created on February 4, 1975 through an Order-in-Council under the Crown Corporation's Act and later on April 1, 1976, the Potash Corporation Act provided for its continuation. PCS was given the mandate to acquire ownership of a significant portion of the potash mining capacity in Saskatchewan and to establish an organization capable of operating the facilities, marketing the product, and conducting all of the other activities necessary for a successful corporation competing in the world potash industry. The corporation is the largest potash producing and selling organization in the Western World - or third largest in the world. (See also Figure 1). PCS through its wholly-owned subsidiary, PCS Mining, has acquired a whole or partial interest in five geographically distinct producing properties or divisions, representing today more than 40% of Saskatchewan's potash producing capacity. The acquisition of each division was followed by a program designed to exploit and maximize the particular opportunities at each minesite for increased production. To that end, PCS Mining has taken an active lead in expanding to meet future demand and has implemented expansion programs at all properties except for its Esterhazy Division where it has a long-term processing agreement with International Minerals & Chemical Corporation (Canada) Limited. Through its wholly-owned subsidiaries, PCS Mining, PCS Sales and PCS Transport, this provincial crown corporation has the ability to operate as a producer and marketer of Saskatchewan's potash. In certain instances PCS, the parent company, assists in the financing of various projects undertaken by the subsidiaries and in other cases the subsidiary involved arranges its own financing. POTASH RESERVES As a background to the specific issue of financing, it is helpful to describe briefly the nature of the deposit which supports the industry - our collateral, if you like. The potash beds underlying Saskatchewan are sedimentary rock deposits formed by the gradual evaporation of an inland sea during the Middle Devonian period roughly 400 million years ago. Now known as the Prairie Evaporite, this formation stretches from North Dakota and Northeast Montana through Southern Saskatchewan into North-Central Alberta. These beds lie at mining depths ranging from 950 - 1000m (3,000 ft) below the surface, where conventional mining methods can be used, and to 1,650m (5,000 ft), where solution mining must be

Jan 1, 1985

By C. E. MacQuigg

MAN?S desire to harden metal is older than recorded history and obviously would date from the moment when he found his implements were not equal to the demands of service. This need for hardness in metal may be divided roughly into two main classifications: (1 :I need for hardness through- out-for purposes of greater strength or elasticity of the whole implement or member, and (2) need for surface hardness alone. A strong steel needed to transmit stresses or resist de- formation is an example of the first class. In metals only surface- hardened, the chief need is for resistance to wear. Obviously the whole gamut of all uses can be imagined- from the extreme of a simple cantilever supporting a load in space to that of a solidly supported face plate serving to resist wear. It is the in- creasing of wear resistance which I propose to discuss.

Jan 1, 1939

By K. H. Nimerick, B. E. Scott, F. J. Beafore

A unique freeze conditioning agent (FCA) which functions by forming structurally weak ice rather than suppressing the freezing point of water has been successful in alleviating frozen coal problems. Frozen coal treated with FCA has been quickly unloaded at temperatures below -17.8OC (O°F). Other applications of FCA include deicing: conveyor belts, idler, idler arms, and other moving parts that have been impeded by ice.

Jan 1, 1980

By N. V. Hansell

l. INTRODUCTION. THE last few years have shown an increasing interest in the subject of beneficiating iron-ores -in all iron-producing countries. In the United States, this movement has been slower than in certain parts of Europe, for the obvious reason that the abundance and relative cheapness of the Lake Superior iron ores has hindered the development of enterprises for the preparation of low-grade ores. Gradually, however, conditions have changed. The world's consumption of iron is increasing enormously. Being in 1900 about 40,000,000 tons, in 1910 ii was already 60,000000; and there is no reason to doubt that for the near future the increase in iron-consumption will continue at the same rapid rate, especially with, the development of China, certain parts of Africa, and other regions which have hardly been touched as yet by modern industrialism. It is. therefore, not surprising that apprehension is felt that the known available iron-ore resources of the world are gradually being depleted. Signs of this feeling are the recent investigation, under the direction of the U. S. Geological Survey, of the iron-ore resources of the United States, and the estimate presented to the last International Geological Congress, at Stockholm, Sweden, of the iron-ore resources of the world. These investigations have emphasized the fact that the known high-grade ore-deposits are limited in extent, and will, at a not distant future, be exhausted, compelling the iron industry to depend for raw material on the enormous deposits of low-grade ores which are distributed over almost all the world. The discovery of new deposits of high-grade ore, in countries not yet thoroughly explored, will not materially change this prospect. Of course, the part which such new deposits will play in the future cannot be forecast. The difficulty and cost of transportation will probably exclude many of them from use at the present centers of the iron industry.

May 1, 1912

By B. D. Cullity, K. S. Sree Harsha

When a copper or aluminum single crystal is swaged into wire, the resulting deformation texture depends on the original orientation of the crystal. The<100> and <111>orientations me essentially stable, while <110> is unstable. The greater the <100> content of the deformation texture, the stronger the wire is in torsion. the greater the<111>content, the stvonger it is in tenszotz. The preferred orientation (texture) of fcc wires, either after deformation or recrystallization, is usually a double fiber texture in which some grains have <100> parallel to the wire axis and others have <111>. The relative amounts of these two texture components, as reported by different investigators for the same metal, vary considerably. Previous work in this laboratory&apos; has shown that the starting texture of a wire, i.e., the texture which it has before deformation, can have a decided influence on the texture produced by deformation. In particular, it was found that the deformation texture of copper wire is essentially a single <100> texture, if the wire before deformation contains only a <100> component. This is true even when the deformation is carried to more than 98 pct reduction in area. This paper reports on further studies of the role played by the starting texture. Copper and aluminum single crystals of various orientations have been cold swaged into wire, and quantitative measurements of the resulting deformation textures have been made. The tensile and torsional properties of the deformed wires have also been measured, and the relation between these properties has been correlated with the texture of the wire. These measurements were made in order to demonstrate that a cold-worked wire can be made relatively strong in torsion and weak in tension, or vice versa, by proper selection of the texture before deformation. MATERIALS The copper was of the tough-pitch variety, containing, by weight, 99.962 pct Cu, 0.003 pct Fe, 0.025 pct 0, and 0.0021 pct Si. The aluminum contained more than 99.99 pct .&apos;41; the only reported impurities were 0.001 pct Fe, 0.001 pct Si, and 0.003 pct Zn, by weight. Large single crystals of these metals were grown by the Bridgman method in graphite crucibles and a helium atmospliere. Cylindrical specimens of predetermined orientation, about 1.5 in. long and 0.36 in. in diameter, were machined from the as-grown crystals and then etched to 0.25 in. to remove the effects of machining. Their orientations were checked by back-reflection Laue photographs, and they were then swaged to a diameter of 0.050 in. (96 pct reduction in area). 111 order to study the "inside texture" of the deformed wires, they were etched, after swaging, to a diameter of 0.040 in. before the texture measurements were made. TEXTURE MEASUREMENTS The fiber texture which exists in wire or rod can be represented by a curve showing the relation between the pole density I, for some selected crystal-lographic plane, and the angle $ between the pole of that plane and the wire axis (fiber axis). Such a curve will show maxima at particular values of , and these values disclose the texture components which are present. The relative amounts of these components can be determined2&apos;3 from the areas under the maxima on a curve of I sin F vs F. It is seldom necesszlry to measure I over the whole range of F from 0 to 90 deg, since the existence of maxima in the low-F relgion can be inferred from measurements confined to the high-F region. The X-ray measurements were made with a General Electric XRD-5 diffractometer and filtered copper radiation, according to one or the other of the following procedures: 1) A method developed in this laboratory,4 involving diffraction from a single piece of wire. 2) A modification of the Field and Merchant method.5 This method was originally devised for the examination of sheet specimens, but it can easily be adapted to the measurement of fiber texture. Three or four short lengths of wire are held in grooves machined in the flat face of a special lucite specimen holder. The axes of the wires are parallel to the plane defined by the incident and diffracted X-ray beams, and the holder to which the wires are attached can be rotated step-wise about the diffractometer axis for measurements at various angles 9.

Jan 1, 1962

By William F. Boericke

CONSIDERABLE waste of oil and grease in lubricating motors and other machinery results from the use of bearings that are not totally enclosed. There is also the likelihood of damage to the bearing through the accidental introduction of grit or dust both in the oiling process and after, unless the cover is entirely dustproof. With the ordinary sleeve bearing that is only partly enclosed, it is generally easier for a careless attendant to cause trouble through neglect than with the ball bearing type, which from its design, must be totally enclosed to give effective service, and needs a minimum of attention. At one of the large mining companies which has taken a leading part in reducing unit costs and pioneering new developments in mining machinery, ball bearings have been gradually supplanting the conventional type of sleeve bearings on many of their motors, centrifugal pumps, and other machines in the mines. This innovation is not recent, as substitution of ball bearings on mine motors was first tried out by this company in 1909. Since then an increasing number of such bearings have been put in. They are now favored because of increased operating efficiency and reduction in lubrication costs.

Jan 1, 1926

By Philip S. Mathews

THE tremendous stimulus given to the mining industry by the gold and silver policy of the present administration has found the capital market for mines ill prepared to afford practical means of financing. Particularly has this been true of the host of abandoned high-cost producers and prospects which increased gold and silver prices have made potentially profitable. In a comparatively short time, experience has demonstrated abundantly that valuable properties have frequently failed to secure capital, while questionable properties have drawn to themselves and their promoters more of the public moneys than their prospects justify. Singularly enough the fault is usually attributable to faulty financing. Discussion and study of this problem are vital to the industry.

Jan 1, 1936

By William Sellers

tested without knowing anything of their chemical composition. I had these pieces separately placed upon 10-inch bearings under a 7-gross ton lianlrner, a piece of 2½-inch round iron laid upon them as a fuller, and the hammer allotved to fall from 20 inches above the fuller, which, according to Haswell, gave a ldow of 67.75 gross tons. The pieces were then turned orcr, the fuller placed upon the convex surface, and the harnnler allowed to fall from 13 inches above the fuller, giving a blow of 58.46 gross tons. You will see that the rails do aot show ally bigrls of ruptnre, and their color at the points of torture prove them to have been absolutely cold when the test was made. I thirk these rails ought to be reasonably safe in the track. As you see by this piece of the head of one of these rails, I had it plarred, and then some teeth cut in it by a cold clrisel, and one-half of them pounded down with a hammer. The teeth of my rack did not break off. The analyses of these rails substquently made are: I. 11. Carbon,... 0.110 0.880 Silicon,..0.050 0.058 Phosphorus ,..0.086 0.082 Manganese,.. 0.042 0 840 In conclusion, I will say that Dr. Dudley&apos;s paper as a contribu tion to our knowledge of steel rails is valuable and interesting, but I protest against his conclusions king reoeived as manufacturing or comtnercial axioms. From its being presented in the form-of a report to the leading railroad of the country from one of its trusted officers, as well as from the tone of the concluding deductions, it is liable to be so received by railroad men. If any railroad com pany desires rails made under either of Dr. Dudley&apos;s formulas, and are willing to pay a price large enough to cover the loss in making them, dl and good; but so long as the rail makers are compelled to gwrrantee the wear of their rails for a given number of years, justice reqnires that. the composition of the steel from which these rails are made should be left to them. WILLIAM SELLERS, PHILADELPHIA: The very interesting paper upon the wear of steel rails that has just been read preseak the record of a series of investigations that are extreniely valuable, and the deduction that bas been drawn from the results noted seems to be unavoidable; the tests, however, to which it is proposed steel rails shall be subjected hereafter, with a view to determine their quality, sllould

Jan 1, 1881