Search Documents

By D. Mills, G. B. Craig

ZIRCONIUM has been float-zone-refined in an electron-beam furnace and the redistribution of oxygen, iron, and tungsten has been measured. The iodide zirconium used in the present experiments initially contained both oxygen and iron in the range 100 to 200 ppm by weight, and tungsten in amounts less than 10 ppm. Float-zone refining of zirconium, using induction heating, has previously been attempted by Kneip and Betterton1 and Langeron.2 Kneip and Betterton were primarily interested in the removal of iron and nickel. They achieved some purification, with respect to both these elements, in material given up to six passes at 150 mm per hr under an argon atmosphere. Langeron reported purification for a large number of elements after four completed passes in a static vacuum system operating at pressures less than 10-6 mm of Hg and with rates of zone travel between 30 and 40 mm per hr. He did not report oxygen concentrations, but stated that there was inverse segregation of this element. westlake5 has also used a minimum of four zone passes to remove iron from zirconium. No rates or conditions were given. Belk6 has shown that tungsten contamination can occur during electron-beam melting. He reported an increase from 0.01 to 0.05 pct by weight tungsten in molybdenum after four complete zone passes. The vacuum system for the electron-beam unit used in the present investigation consisted of a single-stage rotary pump backing a liquid-air-trapped oil-diffusion pump. A pressure of less than 10-8 mm of Hg was obtained with Dow-Corning 705 fluid in the diffusion pump. In order to avoid contamination of the zirconium by evaporation from the tungsten filament, a special focusing cage4 was employed. Three rates of zone travel, 114, 38, and 4 mm per hr, were investigated, with the liquid zone moving from the bottom to the top of the bar. The bars used were 3 mm diam and the total melted length was 130 mm. Oxygen was analyzed by neutron-activation analysis using a neutron flux of 10' neutrons per sq cm per sec to form the isotope N16 by the 016 (n,p) N16 reaction. The standard deviation is quoted for each oxygen determination. The iron and tungsten analyses were performed spectrographically, and the precision is estimated to be ±6 pct. Analyses for tungsten were all below the detectable limit of 10 ppm, confirming the protection given by the focusing cage. No significant redistribution of oxygen was found at the two higher rates of zone travel. The redistribution of oxygen and iron obtained after five passes at a rate of zone travel of 4 mm per hr (1.1 x 10-4 cm per sec) is recorded in Tables I and 11. Burris, Stockman, and Dillon3 have estimated the distribution of solutes during multipass zone refining. Using their curves for an effective distribution coefficient of Keff = 1.5 and 2 for oxygen and Keff = 0.3 for iron, the expected concentrations were estimated for the present material. These are shown in Tables I and 11, along with the experimentally measured values. The calculated concentrations are based on a molten-zone length of 10 pct of the total melted length, whereas in the present experiments the molten zone was approximately 5 pct of the total melted length. The effect of zone length on solute redistribution is most pronounced after a large number of zone passes. Comparison with Pfann's published data8 for solute redistribution for various Keff's and zone lengths indicates only small differences at low numbers of completed zone passes. It is evident that the expected distribution has not been realized in the case of iron. Scrapings of material deposited on the inner surfaces of the electron-focusing cage were found to be magnetic. It is, therefore, concluded that redistribution of iron is masked by evaporation. Deposition of iron inside the focusing cage was observed at all rates of zone travel. The results of the investigation may be summarized as follows: 1) Segregation of oxygen is typical for a solute with a distribution coefficient, Keff > 1. 2) No redistribution of oxygen takes place at high rates of zone travel. 3) The distribution coefficient for oxygen lies between 1.5 and 2.0. 4) Purification with respect to iron occurs mainly by evaporation. 5) The focusing cage is effective in preventing tungsten contamination.

Jan 1, 1967

By Evan Just

Attempting to analyze a 25-year forecast after less than a third of the time has elapsed may seem premature. The President's Materials Policy Com- mission's report necessarily painted with a broad brush and made no claim for pinpoint accuracy in its predictions. More importantly for present purposes, it made no attempt to predict the detailed courses of production and consumption during the period forecasted. Several statistical highs and lows may very well lie between now and 1957, so comparing recent figures with points taken from the report on a straight-line basis would be illogical. Moreover, the report assumed that the general trend of consumption-domestic and foreign-would be upward. Contrarily, domestic figures were lower in 1957 than in 1950. Therefore, to project curves from 1950 through 1957 leads to conclusions that are probably false. Many in the industry would feel more uncertain about forecasting 1975 domestic conditions now than they would have been in 1950, even though nearly a third of the 25 years has elapsed. In making comparisons, several statistical problems are encountered. The Paley report figures for 1950 were estimated in several cases and corrected figures vary as much as 10 pct. For example, the report placed 1950 lead consumption at 800,000 tons, whereas actual consumption was 885,000 tons. Obviously, in comparing more recent figures with the report's projections, adjustments must be made for positions taken in error from the start. Over the long pull, such discrepancies will probably be insignificant, but they must be noted in comparing short-term changes.

Jan 10, 1959

By C Gunther

The term metamorphism as commonly used means any change in a rock in either form or composition, from whatever cause. By metasomatism, according to Lindgren, is meant a metamorphism that involves a change in the chemical composition of a rock by the addition or subtraction of substance. Certain types of metamorphism are due to the action of mineralizing solutions, and are closely connected with ore deposition; they form, therefore, valuable guides in the exploration for ore-deposits. Other types of metamorphism are due to regional processes, and are not connected with ore deposition. By dynamo-regional metamorphism is meant a primary alteration of rocks over large areas under conditions of pressure, flow- age, and heat. This process produces schists and gneisses from either sediments or igneous rocks. It is thought that there is little migration of minerals or of elements in dynamo-regional metamorphism, and that the changes are due chiefly to recrysallization and rearrangement of original minerals in bands with their major axes oriented normal to the direction of greatest pressure. Under these conditions limestones are commonly altered to marble, and sandstones to quartzite, basic igneous rocks to greenstone or serpentine, while rocks of normal or acid com- position commonly yield the usual types of schist or gneiss. Dynamo-regional metamorphism, extending over large areas, has no connection with mineralizing processes, and is, therefore, no guide to ore deposits; while this process has certain features, such as characteristic mineral associations, in common with contact metamorphism, the results of the two processes may usually be distinguished without difficulty.

Jan 1, 1932

By J. A. Retty

HOLLINGER CONSOLIDATED GOLD MINES LTD., through two subsidiary companies, has the exclusive right to prospect in two contiguous areas in central Labrador. This paper presents the results of the mineral exploration that has been conducted in these areas to date. One of the subsidiaries of Hollinger. the Labrador Mining and Exploration Co. Ltd., under an agreement with the Newfoundland Commission of Government, holds an area of approximately 20,000 sq.mi., which comprises the western portion of Newfoundland-Labrador and includes the upper basins of the Hamilton and Naskaupi Rivers. (The main area of the deposits so far discovered may be located on a map at about 67° west longitude and 55° north latitude.) The other subsidiary of Hollinger, Hollinger North Shore Exploration Co. Ltd., has licensed from the Province of Quebec an area of approximately 3900 sq.mi. lying directly north of the Newfoundland-controlled area at the headwaters of the George, Whale, and Swampy Bay Rivers. The M. A. Hanna Co., large iron-ore operators of the Lake Superior region, are participating in the project. With the exception of the years 1940 and 1941, field work has been conducted in the Newfoundland area since 1936, and in the Quebec area since 1939. Hollinger assumed the management in 1942. The field base is at Hollinger Lake, some 300 miles north of the tidewater base at Seven Islands, Quebec, which, in turn, is just west of the mouth of the Moisie River, on the Gulf of St. Lawrence. Air transportation is used exclusively to service the operation.

Jan 1, 1945

By Edward L. Vickers

The Pacific rim countries, comprising more than half the globe, represent a complex mix of developed and developing nations. The area comprises a large segment of the industrialized world. Within its boundaries are also found many of the world's greatest mineral resources largely concentrated in the less developed countries. The conflicting objectives of these developed and developing nations are giving rise to changes in the traditional patterns of world resource development. Powerful political and socio-economic factors affecting the world today are having a great bearing on natural resource developments in the Pacific basin. New forms of partnerships have been emerging in developing nations which have had a great impact on the mining com- munity, lending institutions, as well as political relations. The United States and Japan have been substantially responsible in the past for the development of natural resources in this area of the world. Their role, however, is undergoing significant metamorphosis. The rapidly changing economic and social environment in the developing countries is producing new tensions which affect future collaboration between producers and users of natural resources. To understand current problems, I believe, it is worthwhile to examine historical trends in this area which may help defining alternatives facing us in the future. In modern times the United States was the first country in the Pacific basin to start development of resources on a massive scale. It began with the major exploration of the mineral-rich west of the United States and extended significantly later into Latin America and Australia. In the early 1950's, Japan became a significant

Jan 1, 1976

EDWIN M. CHANCE (communication to the Secretary?).-The subject of miners' lamps. has long interested me and it would seem that the thought that has been given to it by the Bureau of Mines, and the users

Jan 6, 1917

THE Annual Fall Meeting held in Chicago in conjunction with the celebration of a Centennial of Engineering brought forth a round of field trips and symposiums which did much to add to the store of information of the 240 who registered for the gathering. Instead of a scattered program, technical papers were grouped together in organized symposiums, where the particular importance of each report was enhanced by presentation in context. Despite the heavy accent on technical papers and informative field trips, those attending the meeting had ample time to enjoy the benefits of a visit to Chicago. The AIME dinner dance was held at the Palmer House, in the Red Lacquer Room. The Chicago Section played host Friday evening at dinner. The MBD held four sessions at the meeting headquarters, the Palmer House, September 4 and 5. Featuring the meetings was a review of taconite concentration and new theories on comminution. The first session opened with a paper on the Structural Features Which Effect the Concentration of Iron Formations, presented by F. J. Tolonen. The paper was centered upon the various members of the low grade iron formations of the separate Michigan districts. The study correlated macrostructure, microstructure, and concentration tests. [ ] Beneficiation Characteristics of Michigan Low Grade Iron Ores, presented by F. X. Tartaron, cochairman of the session, reviewed the work of his laboratory on the beneficiation of low grade ore taken from various strata of a deep shaft on the Marquette Range. The paper included data on flotation, gravity separation, magnetic separation, and combinations of these processes. The economics of low grade ore treatment generated great interest. Ty. Maki offered a compilation and correlation of field results with magnetic separators in ferrosilicon and magnetite medium recovery circuits. Following the morning session, 130 persons attended a luncheon, followed by a brief business meeting. Later, a film illustrating the grinding, separation, and pelletizing steps investigated by the Mines Experiment Bureau, was presented by H. H. Wade. T. E. Ban, and L. J. Erck gave a report on pelletizing which evoked much discussion. R. A. Limons presented a paper on the Mineralogy of Blast Furnace Sinter, for its author, H. M. Kraner. Friday sessions featured a new hypothesis for high speed drill rod milling and a new technical approach to comminution. Jack Myers commented that Consolidated's large rod mill was a hammer mill turned inside out. Steve Erickson described the use of Cyclones for Heavy Media Concentration of Iron Ore Fines. Bob Meaders gave a Progress Report on the Aerofall Mill. Shiou-Chuan Sun described an improved high frequency analyzer for studying the conductivity of suspensions of various minerals. L. A. Roe discussed a magnetic reflux condensor which enabled him to determine the degree of liberation of magnetic iron ores. Roy A. Johnson described a function of the hydroscilator in which the fan rake was eliminated in favor of a conical bottom. The Industrial Minerals Division sessions held September 5 and 6 and were well attended. The Friday morning session was particularly concerned with developments and advances in industrial minerals with special emphasis on the Chicago area. The first two papers dealt with transportation on the Great Lakes and fuel movement into the Chicago area. The third paper proved to be of great interest, turning the spotlight on the fairly new hydraulic mining methods introduced by a silica company in the Ottawa, Ill. field.

Jan 1, 1952

THE Boston meeting, August 29-31, was in many ways one of the pleasantest the Institute has enjoyed in years. Much hard work had been done by the committee, and with excellent results. The program had been purposely restricted with the idea that a smaller, more homogeneous audience formed the best basis for a regional meeting, and the event fully justified the plan. The one hundred and sixty-three members and guests attending were dominantly interested in geophysical methods or their application, and, despite the highly technical character of the papers and the unusual heat, attendance and interest in the technical sessions were well sustained. The exhibition of geophysical instruments and aerial maps added greatly to the meeting.

Jan 1, 1928

New Products Equipment

Jan 11, 1950

By W. R. Crane

While professiorlally engaged in the oil- and gas-fields of Kansas, in measuring the pressure and flow of gas-wells, and studying the phenomena attendant upon the production of both oil and gas, I noticed in the flow of gas a peculiar and interesting feature. That there are actual lines of flow in liquids (non-compressible fluids) discharged through an orifice, or a short section of pipe, is shown by the external shape of the discharge—the vena contracts. Such lines of flow are not observable in the discharge of gas from an orifice. It can hardly be questioned that they exist. That they are not apparent is probably due to the very small weight of the gaseous particles, which climinishes the momentum of their movement in a given direction, acquired before they issue from the orifice, and also to the expansion of the gases, which would exert a powerful influence in overcoming any such tendency in their flow. Gas flowing from an orifice, supplied by a large reservoir or blowing-engine, exhibits almost the reverse of what is noticed with liquids. Namely, the gas assumes the form of an inverted truncated cone, of large angle: with its apex-end at the orifice. (See BB, Fig. 1.) This external ahape assunled by the flow of gas shows, however, marked differences under varying conditions of volume and pressure. For instance, a large volume of gas under high pressure, flowing through a 2- or 3-in. pipe, as in the case of a natural gas-well, assumes a more definite conical form, the angle of which increases as the pressure falls. Moreover, outside of the well-defined inverted cone is a thin conical heath or zone of gas, A A, the angle of which is considerably greater than that of the main cone, and increases with +1UNIVERSITY OF KANSAS, LAWRENCE, KANSAS.

Jan 1, 1905

By Francois E. Heuze

INTRODUCTION Rock slope stability typically is governed by the geological discontinuities. This stability can be improved by drainage, unloading, adjustment in slope orientation, adjustment in slope angle, and also by reinforcement such as bolts or tendons. This paper addresses the modeling of bolt reinforcement in rock slopes. Most geological discontinuities such as joints have rough surfaces; they dilate during shear displacement. Their shear strength is characterized by two envelopes (Fig. 1); the peak envelope is distinct from the residual envelope when the joints can dilate. If the dilation is restrained transversely, such as with bolts, the normal stress will increase and the joint strength also will increase. It has been demonstrated that this increase may be considerable (Obert et al., 1976). The new normal stress at peak strength is a com- posite function of the properties of the rock mass and of the steel (Heuze, 1979). Hence, the dilation and its resultant effects on joint shear strength must be included in the analysis and design of the reinforcement. We present a model which can be used to perform such an analysis. Early studies of rock reinforcement in mining and civil applications (Lang, 1957 - Panek, 1962 - Osen and Parsons, 1966 - Lang, 19721, did not consider the specific effects of bolts on joint shear strength. In 1973, Heuze and Goodman reported direct shear tests on rough sandstone joints with bolts perpendicular to the joint plane (Fig. 2). The peak shear strength of such joints was greatly in excess of the shear strength of the unbolted joints. The excess

Jan 1, 1983

By G. G. Hancock, H. H. Johnson

Hydrogen gas at atmospheric pressure is shown to cause substantial embrittlement in a martettsitic high-stretzgth steel. Subcritical crack growth is observed at very lom stresses and with high growth rates. It is suggested that an adsorbed layer of hydrogen atoms at the crack-tip surface provides the damaging hydrogen. Oxygen in small quantity, as little as O.7 pct by volume, is shown to eliminate subcritical crack growth in gas environments caused by hydrogen or water vapor. However, dissolved oxygen in water has little or no influence upon crack-growth rates. Oxygen-stopped cracks may be restarted by water, or by hydvogen or water vapor if oxygen is removed from the environment. These observations are interpreted in terms of preferential adsorption of oxygen at the crack tip and the formation of an oxide barrier. RECENT investigations1-3 have demonstrated that environmental factors are frequently responsible for delayed failure in martensitic high-strength steels. The environment causes crack initiation from preexisting cracklike flaws at unexpectedly low stresses, often far below the uniaxial yield strength. The crack then propagates at a rate controlled by the environment and the crack-tip stress-field intensity; during this period crack propagation will cease if either the stress or the aggressive environment is removed, and this may be considered a definition of subcritical crack growth. Fracture occurs when the crack has grown to a critical length, such that the fracture toughness of the steel is exceeded. Several liquids are known to cause delayed failure, but water and water vapor are the most severely damaging of the environments investigated to date.'-3 It has been suggested that hydrogen produced during corrosion reactions may be the actual embrittling agent2 The severe embrittlement caused by water vapor inevitably raises the question as to whether other gas environments are damaging. Previous work4'5 has demonstrated that high-pressure hydrogen (2250 psi or greater) is an effective embrittling medium, as measured by such criteria as reduction in area, notch tensile strength, and time to failure. Moreover, the embrittlement was eliminated by the addition of small quantities of air or oxygen to the high-pressure hydrogen, but it was not influenced by additions of nitrogen or argon.4 In the present study attention is focused upon gas environments at atmospheric pressure, in particular hydrogen and oxygen. The influence of these constituents upon the initiation and growth of a crack from a pre-existing cracklike flaw in a high-strength steel was determined directly by the electric-potential method of monitoring crack growth. MATERIALS AND PROCEDURE The H-11 steel was supplied by the U.S. Naval Research Laboratory as 3 by 12 by 0.065 in. sheet specimens with 1-in. transverse center slots. The slot tips were finished by Elox machining to a radius of 0.001 in. or less. The yield strength was 230,000 psi; chemical composition and heat-treatment schedule are given in Table I. The experimental apparatus, precracking procedure, and incremental loading sequence have been described previously.3 In the only significant change, precracking was sometimes carried out by a hydrogen embrittlement and baking technique. All experiments were conducted at room temperature; the hydrogen gas environment was purified by a commercial palladium purifier. Crack initiation and propagation were followed by the electric-potential method,'-3 using a calibration that has been recently dicussed. Stress-field intensities at the crack tip were computed by the conventional Irwin frmula; the plasticity correction was negligible and therefore not included. EXPERIMENTAL RESULTS A striking brittleness associated with molecular hydrogen at atmospheric pressure is demonstrated by the data in Table I1 and Fig. 1, which indicate that subcritical cracks in hydrogen initiate at lower stress-field intensities and propagate more rapidly than in fully humid argon. Ki and Kf are the crack-tip stress-field intensities at initiation and termination of subcritical crack growth, respectively. Termination, of course, corresponds to fracture. In both hydrogen and humid argon Ki is less than Kf

Jan 1, 1967

By R. P. Rothwell

THE first difficulty mentioned is that in some instances two or more beds of coal separated by sandstone or slate rocks of considerable thickness in one part of a basin, are found running together in another part. Of course, we may happen to strike first the part of the basin where there is but a single seam, and in this case the bed would appear to divide into two or more branches within a short distance. Such cases are not rare in the anthracite coal-fields. I would suggest as an explanation of this phenomenon the gradual sinking of the peat-marsh-the embryo coal-bed-on one side, and the moving forward of the marsh, so that on one part of the bed the formation of peat would still be progressing, while another part, being under water, would be covered with mud and sand. Thus we have different portions of the same bed of different ages. Now if the sinking of the marsh be stopped for a time, the bed will become thicker in the portions left exposed, and if the sinking now changes in direction, so that the part that had previously gone down com¬mences to rise, we should have the phenomenon of a bed, continuous throughout, with one portion overlying another, and separated from it by rock strata. These are exactly the conditions observed in splitting beds. While one side of the lake is sinking, and the peat-marsh moving on in that direction, the other side may be rising,

Jan 1, 1873

By E. W. Davis

THIS nation has been depending upon the Lake Superior iron ranges for most of its iron ore requirements for over half a century. Furthermore, it can continue to draw the major portion of its ore requirements from the same source for another century or more, but to accomplish this, great changes must take place in the present ore mining industry. Preliminary preparations for these changes are now underway and in the next few years decisions of far-reaching importance must be made. But to understand the situation, it is first necessary to know something of the nature and occurrence of the Lake Superior iron formation. So far as is known, the merchantable grades of iron ore remaining in the various Lake Superior ranges are as shown in Table 1, which shows that

Jan 1, 1947

By J. H. Swisher

In measuvements of the solubility of nitrogen in fer-rilic Fe-P alloys, tile nitrogen solubility is found to be Less in pIrospliorus-bearing alloys than in pure iron. The reduction in solubility is about 20 pct in a 1.0 wt pct P alloy at 1300°C and about 30 pct in a 0.23 wt pct P alloy at 440°C. Diffusion coefficient measurements at 1150 and 585°C show that phosphorus also decreases the nitrogen diffusivity in iron. In previous work on the Fe-P-N system, phosphorus was found to reduce the nitrogen solubility in liquid iron slightly.&apos; Indirect evidence for similar behavior in a Fe at low temperature was obtained by Dickenscheid and Brauner.&apos; These authors found that phosphorus reduces the height of the internal-friction peak due to dissolved nitrogen. The results of Dickenscheid and Brauner were confirmed by J. C. Swartz of this Laboratory in a single internal-friction experiment using the same specimen stock as in the solubility measurements described below. In the present investigation, the solubility of nitrogen in a fer rite-stabilized Fe-1.0 wt pct P alloy was measured in the temperature range from 800" to 1300°C. Additional experiments were performed in the temperature range from 440° to 585°C, using an Fe-0.23 wt pct P alloy and NH3-H2 gas mixtures. EXPERIMENTAL The experiments were performed in a vertical tube furnace wound with platinum wire. For experimental temperatures of 800°C and above, a mixture of 5 pct Hz in N2 was used as the reacting gas. The gas mixture was prepurified from oxygen by passage over platinized asbestos at 450°C, and subsequently over anhydrone to remove water. Flow rates of the gases were measured with capillary flow meters. The temperature was measured before and after each experiment with a Pt/Pt-10 pct Rh thermocouple. The specimens used for the high-temperature solubility measurements were in the form of rectangular plates, 0.534 by 1.6 by 3.8 cm. The specimens were cleaned in trichloroethylene and annealed for 2 hr in hydrogen at the beginning of each experiment. In measuring the nitrogen solubility, the specimens were held in the reacting gas until equilibrated, then cooled in a water-cooled copper block at the bottom of the furnace. The time needed for equilibration at 1150°C was determined by measuring the average nitrogen content of the 1.0 pct P alloy as a function of reaction time. As will be described, the nitrogen diffusivity in the alloy at 1150°C is only slightly less than its calculated diffusivity in pure iron. At temperatures other than 1150°C, the reaction time used in measuring the nitrogen solubility was about twice the calculated equilibration time for pure iron at the same temperature. With a few exceptions, the procedure for the low-temperature solubility measurements was the same as that described above. The compositions of the NH3-H2 gas mixtures were determined by collecting gas samples from the gas train and analyzing them for NH3 by titration with HC1. The specimen thicknesses were less than those used for the high-temperature experiments, eg., 0.124 and 0.051 cm for measurements at 585° and 440°C, respectively. Nitrogen concentrations were obtained by chemical analysis, using the Kjeldahl method. The Fe-P alloys were made by adding ferrophos-phorus to electrolytic Plastiron (Type 104 A). Commercial ferrophosphorus, containing 3 pct Mn and 0.35 pct Si as the major impurities, was first purified by melting under an FeO slag. In a separate heat, the electrolytic iron was melted and vacuum-carbon-deoxidized prior to making the ferrophosphorus addition. The principal impurities and their concentrations in weight percent in the 1.0 pct P alloy are as follows: Mn, 0.01; Si, <0.01; C, 0.01; 0, 0.003; and N, 0.0012. The impurity levels in the 0.23 pct P alloy are con-

Jan 1, 1968

By Herbert Hoover

YOUR committee asks that I speak today on the relations of the engineering profession to public affairs. That takes in a lot of ground. This being a cheerful occasion, I will assume that I should exclude the engineer&apos;s function as a taxpayer. This being a nonpartisan occasion, I will assume that I should not refer to his voting emotions in 1940. Perhaps what was in the minds of your committee was the application of engineering thought to the confusions of the times. That is also a lot of ground. I fear, however, its boundaries disappear in mirages and rainbows on all sides. Now any entry of the engineer into public affairs involves his breaking into the fields of the sociologists, the economists, and the politicians. However I don&apos;t know why, seeing the difficulties these professions are having, they should not welcome a little help.

Jan 1, 1939

By H. W. Camp

ALTHOUGH the situation in the oil industry during the past year has. not been conducive to large expenditures for development and research, there is little indication that such expenditures have been curtailed. While few outstanding achievements have been reported, considerable progress has been made in the development of new products and the adaptation of petroleum derivatives to new uses. The most important question facing the refiner today is the anti-knock quality of his gasoline. This year has seen the widespread adoption of the term "octane number" as a measure for anti-knock values, and in the latter months of the year the public has been made acutely aware of this condition through competitive advertising. Gaso-line is no longer priced on volatility and gravity alone, but on octane number as well; and premiums are being paid for material of relatively high octane rating. The situation has grown more and more competitive and has forced refiners continually to raise the octane rating of their regular and com-petitive grades, and at this writing the same situation exists for premium grades which have possessed relatively high anti-knock properties for some time. Straight-run gasoline produced from paraffin-base or semiparaffin-base crudes has an inherently low anti-knock value, and in order to convert this material to a higher quality it has been found necessary to crack an increasing percentage of the crude oil charge. By completely cracking the heavier portions of the crude, and blending back with the straight-run gasoline, it has been possible to produce an average of 63 to 65 octane number gasoline&apos; on average Mid-Continent crude. This operation carried to the fullest extent does not suffice, however, and the recent and rapid development of the so-called "re-forming unit," has resulted. The straight-run gasoline fraction is cut into two parts: a light, low boiling point gasoline; and a heavy gasoline or naphtha. The latter containing the low anti-knock portions of the gasoline, is sent through a re-forming unit and subjected either to high temperature ,or pressure, or both, which materially increases its octane number. On average Mid-Continent the blend of low boiling point straight-run,

Jan 1, 1932

By J. R. Low, M. Gensamer

During the course of an investigation into the drawability of automobile-body sheet steel, it became apparent that certain advantages would be possessed by a deep-drawing steel with a very low yield strength, but almost normal tensile strength, provided a reduction in yield strength could be accomplished without sacrifice of ductility and fine grain size. It would also be desirable to have this steel free from strainaging; that is, free from the tendency for the yield point to return after it had been eliminated by straining. It was known that wet hydrogen treatment acted to eliminate aging, but as carried out by other investigators, at relatively high temperatures, this treatment resulted in grain coarsening. It has been established by some of the experiments reported in this paper that all of these objectives can be accomplished by treatment in wet hydrogen at a low temperature, in the neighborhood of 720°C. The time of treatment is relatively short (about 3 hr. to completion with 20-gauge sheet) if the water content of the hydrogen atmosphere is made fairly high, say almost 30 per cent by volume. At this temperature, the grain size remains fine in the time required. After this treatment sheet reduced the usual amount by cold-rolling has a grain size of about A.S.T.M. No. 7. The yield point is completely eliminated, and the yield strength is reduced to a very low value, in the neighborhood of 15,000 lb. per sq. in. The stress-strain curve departs gradually from the straight-line elastic part after the fashion of nonferrous deep-drawing alloys. This elimination of the yield point is accompanied by a very low indentation hardness; for example, 32 Rockwell B or even lower. There is no aging as measured by increase in the yield strength upon aging at room temperature or for 3 hr. at 200°C., after stretching about 10 per cent in tension. Tensile strength is only slightly less than the box-annealed sheet, seldom dropping much below 40,000 lb. per sq. in. Elongation is practically unchanged, or increased slightly. The term yield point, as here used, refers to the phenomenon of heterogeneous deformation occurring at a substantially constant load, observed principally in annealed low-carbon steels. If such a steel is loaded in tension, the load increases steadily with elastic strain, suddenly falls, fluctuates slightly about some constant value for a time and then begins to rise again as deformation proceeds. The maximum initial load before the sudden drop is generally called the "upper yield point"; the value of the load where deformation proceeds at a

Jan 1, 1943

By C. E. Mills

The Verde mining district is in Yavapai County, in north-central Arizona. Jerome, the principal town, has a population of 6000 and the two important mines of the district—the United Verde and the United Verde Extension—lie almost within its limits. Perched high on the southwest side of the Verde valley, at elevations of 4800 and 5500 ft. (1463 and 1676 m.) respectively, both mines have long tunnels from their lower levels through which the ore is hauled to the smelters. Clarkdale, the smelter town for the United Verde mines, lies in the Verde valley 4.1 miles (6.5 km.) distant in an air line from Jerome and at an elevation of 3560 ft. The two towns are connected by the standard-gage railroad of the Verde Tunnel and Smelter R. R., a subsidiary of the United Verde Copper Co. This road is 11 miles long and has a compensated grade of 4 per cent. At Clarkdale it connects with the Verde valley branch of the Santa Fe railroad. Clemenceau, the smelter town for the United Verde Extension mine, lies 3.5 miles (5.8 km.) in a southeasterly direction from Clarkdale, at an elevation of 3420 ft. It is connected to the Verde Valley branch of the Santa Fe railroad at Clarkdale by the Arizona Extension R. R., a subsidiary of the United Verde Extension Mining Co. The portal of the haulage tunnel, at an elevation of 3757.5 ft., is also connected with the smelter town by 4 miles of standard-gage track belonging to the same company. In the vicinity of Jerome, the great southern escarpment of the Arizona plateau forms the northeast side of the Verde valley. The general level of this escarpment, or "rim" as it is called, is about 4000 ft. above the Verde River. A corresponding elevation is reached only by the highest peaks of the Black Hills, which bound the valley to the southwest. Two lava-capped mesas, known as "Mingus" and "Woodchute mountains," form the culmination of the Black Hills. That part of the Old Black Hills mining district which lies between their crests and the Verde River is now known as the Jerome, or Verde, mining district. If the smelter towns are not included, a strip about 7 miles long by 3 miles (11 by 5 km.) wide, embraces practically all of the properties belonging to the Jerome district. T-bis strip lies parallel to and along the side of the Verde valley from First View, 2 miles northwest from Jerome, to the

Jan 1, 1925

By W. B. Mather

Arkansas&apos; nonmetalliferous deposits are of many different types. The principal types briefly described in this paper are: clays, shales and slates; silica deposits; limestone and dolomite; barite; gypsum; celestite; nepheline syenite; greensand; phosphate; vermiculite; fuller&apos;s earth; bentonite; diamonds; sand and gravel. The future development of these deposits is expected to effect profoundly the industrial development of the state.

Jan 5, 1950