Search Documents

By MARK H. LAMB

(Canal Zone Meeting, November, 1910.) THE recent growth of a sentiment among cyanide-plant designers against the use of gravity-stamps for the crushing preliminary to cyanidation may be said to date from the almost simultaneous perfection of the ribbed tube-mill liner and of the tall, air-agitation tank. The first step in the resulting change of practice was the universal adoption of the tube-mill for fine-grinding and the use of coarse screening oil the battery. This was the beginning of the surrender of supremacy by the gravity-stamp ; since merely the single fact that it was a more economical machine for crushing fine had retained it in favor as compared with ball-mills, rolls, or steam-stamps. The surrender, however, is not yet complete. It is the universal practice to use rolls where a relatively small tonnage is to be crushed coarse, as, for example, when coarse concentration is included in the plan of treatment. Power, attendance, repairs, and first-cost are smaller for the rolls, under such circumstances, than for stamps; and it is becoming daily more apparent that, with no concentration to provide for, the use of rolls and tube-mills, without the complication of trommels and elevators required by concentration, is rapidly gaining favor in the eyes of the leading designers. The next step was the use of the rapid-running Chilean mill between the gravity-stamps and the tube-mill, which again narrowed the field of operation of the gravity-stamp while radically widening its screen-aperture. Such a combination of stamps and Chilean mill offers advantages when fine concentration is necessary, since the reduction in the Chilean mill call be adjusted easily and governed by varying the screen-mesh. But even concentration is now looked at askance. One of the leaders of this metallurgy has abandoned the separation and

Jul 1, 1910

The Library of the above-named Societies is open frond 9 A.M. to 10 P.M., except on holidays. It contains about 70,000 volumes and 90,000 pamphlets, including sets of technical periodicals and the publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated front sources of information. To these the Library, through Its Library Service Bureau, can render valuable service through correspondence; letters requesting information will receive especial attention. The Library is prepared to furnish references and photographic copies of articles on mining and metallurgical subjects; to determine the existence of mining neaps, and to furnish general information on the geology and mineral resources of all countries. All communications should he made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be, sent more promptly and in more usable shape.

Jan 1, 1917

By Clyde E. Williams

DESPITE the confusion resulting from the depression and the beginnings of recovery, important progress in all branches of iron and steel metallurgy has been accomplished during the year 1933. Research work has been intensive and highly technical, with increasing attention paid to fundamentals. Plant application of research developments has been rapid. Highly specialized laboratory methods were used for the study of iron-ore concentration methods. More attention has been given by the blast-furnace operator to the sizing of ore and the elimination of fines from the charge by the use of sinter. Combustion in the open-hearth has been placed under better control and the insulation of open-hearth furnaces has spread rapidly, with resultant higher fuel efficiency and better control of the melting and refining operations. Control of iron oxide content in the slag and the determination of iron oxide and other inclusions in steel received great attention during the year.

Jan 1, 1934

By Thomas J. Menner

Jan 1, 1983

By F. C. Farnham

THERE has been very little, if any, uniformity in the reference datum used for magnetometer surveys. It has been the practice to choose a base station at which the magnetic field is assumed to be normal and call the difference in field strength between a given station and this base the anomaly at the given station. For small-scale surveys latitude and longitude corrections may or may not be applied, but for large-scale surveys such corrections usually are applied. The United States Coast and Geodetic Survey maps showing lines of equal magnetic intensity are commonly used to determine the normal latitude and longitude variation by scaling values from the map for given points and computing the change per mile north and the change per mile east. This method has been quite satisfactory for isolated surveys, but when two surveys originating at different base stations were extended until they joined, difficulty arose, not only because of discrepancies between base-station values, but also because of differences between the latitude and longitude correction factors used for the separate surveys. It is the purpose of this paper to describe a reference datum for magnetometer surveys which, it is believed, will eliminate most of the difficulty arising from this source. In order to be satisfactory, a general datum for magnetometer sur-veys should be as close as possible to the observed field and still he based on some assumed distribution of magnet poles, in order that the "normal" value of any component of the field for any given point may be computed to as many significant figures as desired. Such a field has been com-puted, and a comparison of the intensity of its vertical component with the average vertical intensity for the United States as shown by the U.S.C.G.S. map of lines of equal intensity for 1935 is shown in Fig. 1.

Jan 1, 1939

M. AlbERtson, Chairman. Production Engineer, Shell Petroleum Corporation, Houston, Texas. R. P. McLaughlin, Associate Chairman. General Manager, Burnham Exploration Co., Los Angeles, Calif. Eugene A. Stephenson, Secretary-Treasurer. Professor of Petroleum Engineermg, Missouri School of Mines and Metallurgy, Rolla, Mo. Ezecutive Commillee M. Albertson, Chairman. C. E. Beecher, Empire Oil & Refining Co., Bartlesville, Okla. L. L. Foley, Petroleum Engineer and Geologist, Tulsa, Okla. R. B. Kelly, Division Manager, Pure Oil Co., Fort Worth, Texas. Hallan N. Marsh, Production Engineer, General Petroleum Corporation of California, Los Angeles, Calif. R. E. Somers, Geologist, The Gulf Companies, Pittsburgh, Pa. Production Engineering T. V. Moore, Vice-chairman. Charge Production Research Division, Technical Service and Development Dept., Humble Oil & Refining Co., Houston, Texas. Joseph Chalmers. De Bataafsche Pet. Maatschappij, The Hague, Netherlands. M. L. Haider, Petroleum Engineer, Carter Oil Co., Tulsa, Okla. Emile HUGUENIN, Deputy State Oil and Gas Supervisor, Los Angeles, Calif. Carl E. Reistle, Jr., Petroleum Engineering Dept. Humble Oil & Refining CO., Houston. Texas. Produclion J. Terry DUCE, Vice-chairman. Geologist, The Texas Company, New York, N. Y. Basil B. Zavoico, Associate Vice-chairman. Consulting Geologist, Houston, Texas. Engineering Research R. L. Huntington, Vice-chairman. Associate Professor, Petroleum Engineering, University of Oklahoma, Norman Okla. Economics Sidney A. Swensrud, Vice-chairman. Assistant to the President, Standard Oil CO., Cleveland, Ohio. Refinery Engineering Walter Miller, Vice-chairman. Vice-president, Continental Oil Co., Ponca City, Okla.

Jan 1, 1937

By F. L. Bosqui

NO metallurgical process developed in the last half century has been more widely advertised to both technologists and lay- men, or has done more to promote efficiency and economy in the extraction of the valuable portions of ores than has the flotation process. Practically everybody has heard of this strange procedure whereby the heavy portions of an ore are made to float while the light parts sink. Some- times it is called froth flotation, the mineral-bearing froth being from the first a distinguishing characteristic. Many times it is called oil flotation, because a thin film of oil was commonly applied to the particles to be floated to make them adhere to the bubbles that rise through the pulp to form the surface froth. Oil, though commonly used, is not, however, necessary for this purpose, which is one of the facts that has been learned as the process has been developed.

Jan 1, 1940

By Walter F. Gries

AN ounce of prevention is worth A a pound of cure' is an old proverb that has sometimes been forgotten in programs having to do with the health of workmen. Realization of the truth of this maxim is increasing, however, and today the iron-mining industry, with which I am particularly concerned, is becoming more alive to the prevention of illness and the conservation of health, thus decreasing the need for treatment after diagnosis has established its necessity. The healthy workman is the happy, efficient workman, and new programs tending to make him more health-minded are being put into operation. Preventive medicine is less costly than corrective medicine, to say nothing of the better results obtained. Periodic physical examinations, with close follow-up attention when required, have reduced the time lost because of illness, workmen's compensation costs, and group-insurance benefits for nonindustrial disabilities.

Jan 1, 1939

By H. R. Drullard

TO obtain the best results from hammer drills, close attention must be paid to two factors in drill maintenance, which are of equal importance; one is lubrication, the other is the shank. With the exception of stoping drills, most modern rock drills require both oil and grease. The oil ports are in the lubricator, on or behind the hammer cylinder; the grease port for the lubrication of the chuck sleeve and rotating mechanism is on the chuck end. Ordinary machine oil is not adapted to rock drills; a heavier more gelatinous oil such as castor machine oil or liquid grease should be used. The lubricators should be filled once for every 12 or 14 ft. (3.5 to 4 m.) of hole drilled. Grease guns should be used to fill the port in the chuck end once a shift; a medium (No. 3) grease is well adapted to this purpose. Hard grease must not be put into the lubricators, as it will not flow through that part. Contrary to the popular belief, oiling a machine once or twice a shift does not provide sufficient lubrication; the drills should be oiled once for every 12 or 14 ft. of hole drilled. The rotating handle of a stoping drill is an oil reservoir and is provided with a port for oiling. The rotating handle is packed with wick-ing, or similar material, which causes the oil to feed slowly from the handle to the other parts of the machine. Stoping drills require oil at least twice a shift; lighter oils than castor, such as Arctic Ammonia, may be used. Drills used in shaft sinking can be oiled satisfactorily by placing a good-sized, drop, sight lubricator on the station above the sinking operations and connecting it with the air-line supplying the sinking drills. If this lubricator is properly filled and adjusted, a uniform oiling of the sinking machines will be effected without the necessity of oiling the drills individually. The grease end should be filled at the station or surface before each drilling period. The shift boss should see that the machines are greased and also that the lubricators at the station function properly. The life of the air-drill hose is somewhat shortened by this method, as oil attacks the inner tube; but as some oil is always present in the compressed air, this is not a serious objection to the method.

Jan 1, 1922

By A. P., Svenningsen

ECONOMICAL handling of a minimum of 25,000 tons of minus 3/4-in. ore per day, grinding it to 2 per cent on 65 mesh, and effecting a high recovery of the copper at the lowest possible cost were the principal aims in the design of the new Morenci concentrating plant. Dealing with a tonnage of this magnitude, it is obvious that lost motion cannot be tolerated. When ore is carried on a conveyor an unnecessarily long distance or elevated to a greater height than necessary, or when pulp flows in a launder by a circuitous route thereby losing elevation and distance, we have lost motion which is always costly both from the standpoint of construction and operation. In addition to the 25,000 tons of ore which must be handled, 100,000 tons of water per day has to be carried through the plant in the treatment of the ore. Though water is not so difficult to handle as the ore, the combined tonnage represents a figure which could easily run into a considerable monetary loss per day if all phases of the design were not carefully followed with the idea of eliminating any unnessary handing of materials.

Jan 1, 1942

The total crude production from the Dutch East Indies, and the British Protectorates of Sarawak and Brunei for 1932 is given in the following table: Production, which had shown a rapid increase from 1921 to 1929, has since been reduced. Exploitation drilling in the majority of the larger fields was suspended and existing production kept within predetermined limits by beaning. Most of the smaller fields were shut down entirely. The depth of producing levels varies widely in the different fields. Shallow fields with drilling depths to 500 meters (1650 ft.) are still numerous as well as those with depths between 500 and 1000 m. (3300 ft.). A few of the newer fields reach greater drilling depths up to 1600 m. (5250 ft.). The deepest exploration well drilled to date (Djambi field, South Sumatra) reached a, depth of 2332 m. (7650 ft.) before abandonment in March, 1930. The specific gravities of the various crude oils produced range between 0.65 (86.2° A.P.I.) and 0.95 (17.5° A.P.I.). The lighter crudes have a high gasoline content and fuel oils are derived from the heavier crudes, which usually are rich in paraffin. Producing companies are: De Bataafsche Petroleum Maatschappij (Royal Dutch-Shell combine in Dutch territory); The Anglo-Saxon Petroleum Co. Ltd. (Royal Dutch-Shell combine in British territory); De Nederlandsch-Indische Aardolie Maatschappij (De Bataafsche Petroleum Maatschappij-Dutch East Indian Government combine); De Nederlandsche Koloniale Petroleum Maatschappij (Standard Oil Co. of

Jan 1, 1933

By Jack R. Elenbaas, Donald L. Katz

A radial turbulent flow formula has been developed which permits the computation of the pressure drop for radial flow in gas wells whether the flow is laminar, turbulent, or partially laminar and partially turbulent. Using the formula a complete back-pressure curve has been calculated and analyzed by a comparison with existing back-pressure curves. A procedure is presented for computing the permeability of the porous media when the porosity, sphericity and average particle diameter are known. Introduction Recent studies on the flow of fluids through porous media have provided new methods for computing flow under turbulent conditions. The present study was initiated as an investigation of pressure -drop computations for flow through porous sands in gas wells and as an analysis of present-day back-pressure tests. Although laminar flow exists in the producing formation of gas wells under normal flow rates, turbulent flow does take place adjacent to the well bore. As the flow rate is increased, turbulent flow exists further and further into the producing formation and under open-flow conditions in relatively deep wells a considerable portion of the flow through the sand will be turbulent. In order to calculate a complete backpressure curve for relatively deep wells without resorting to extrapolation of curves drawn from data obtained in back-pressure tests or calculations made in the completely laminar region, it was necessary to have some means of calculating pressure drop for flow through porous sands under turbulent conditions.4.6 As a result, a radial turbulent flow formula was derived from the equations recently presented by Brownell and Katz.1 A rigorous solution of this equation involves a trial and error graphical integration. By making the assumptions of average viscosity, temperature and compressibility factor of the flowing gas, it was possible to graphically integrate the relation for the general case of radial flow of gases through the porous sand of gas wells. A chart has been prepared relating the value of the integral to the radius of the well bore and to the Reynolds number of the flowing gas. The chart actually performs the graphical integration and the solution of the formula is then reduced to a simple trial and error calculation. A typical back-pressure curve is calculated to show the transition from laminar to turbulent flow. This paper will briefly describe the pro-cedurcs for computing flow through porous media, including a method for predicting sand permeability from porosity and grain size and shape. Flow through Porous Media Brownell and Katzl recently reported a correlation for computing flow of fluids through porous media by the use of an enlarged Reynolds number and friction factor in which the porosity of the bed is included as an additional prime variable. The enlargcd Reynolds number com-

Jan 1, 1948

By Donald L. Katz, Jack R. Elenbaas

A radial turbulent flow formula has been developed which permits the computation of the pressure drop for radial flow in gas wells whether the flow is laminar, turbulent, or partially laminar and partially turbulent. Using the formula a complete back-pressure curve has been calculated and analyzed by a comparison with existing back-pressure curves. A procedure is presented for computing the permeability of the porous media when the porosity, sphericity and average particle diameter are known. Introduction Recent studies on the flow of fluids through porous media have provided new methods for computing flow under turbulent conditions. The present study was initiated as an investigation of pressure -drop computations for flow through porous sands in gas wells and as an analysis of present-day back-pressure tests. Although laminar flow exists in the producing formation of gas wells under normal flow rates, turbulent flow does take place adjacent to the well bore. As the flow rate is increased, turbulent flow exists further and further into the producing formation and under open-flow conditions in relatively deep wells a considerable portion of the flow through the sand will be turbulent. In order to calculate a complete backpressure curve for relatively deep wells without resorting to extrapolation of curves drawn from data obtained in back-pressure tests or calculations made in the completely laminar region, it was necessary to have some means of calculating pressure drop for flow through porous sands under turbulent conditions.4.6 As a result, a radial turbulent flow formula was derived from the equations recently presented by Brownell and Katz.1 A rigorous solution of this equation involves a trial and error graphical integration. By making the assumptions of average viscosity, temperature and compressibility factor of the flowing gas, it was possible to graphically integrate the relation for the general case of radial flow of gases through the porous sand of gas wells. A chart has been prepared relating the value of the integral to the radius of the well bore and to the Reynolds number of the flowing gas. The chart actually performs the graphical integration and the solution of the formula is then reduced to a simple trial and error calculation. A typical back-pressure curve is calculated to show the transition from laminar to turbulent flow. This paper will briefly describe the pro-cedurcs for computing flow through porous media, including a method for predicting sand permeability from porosity and grain size and shape. Flow through Porous Media Brownell and Katzl recently reported a correlation for computing flow of fluids through porous media by the use of an enlarged Reynolds number and friction factor in which the porosity of the bed is included as an additional prime variable. The enlargcd Reynolds number com-

Jan 1, 1948

By James E. York

THE honor so fairly earned and so incompletely and tardily paid to Henry Cort, the inventor of the puddling-furnace and the, rolling-mill, has been fully set forth by Mr. Charles H. Morgan,1 and needs no further emphasis here. In view of the importance of the rolling-mill in the treatment of iron and steel, the paucity of information concerning it is surprising. With the exception of a hook, written about 35 years ago, by Peter Bitter von Tunner, an Honorary Member of this Institute, and of desultory articles on simple sections, which have appeared in technical journals, I know of no pub¬lication attempting to treat this subject, although volumes have been written on the scientific theory and technical manipulations involved in other branches of the iron- and steel-industry. This strange anomaly may be due to the fact that roll-turning cannot be called a scientific business. It does not ordinarily come within the range of an educated engineer; yet it cannot be performed by an ordinary mechanic. It demands some of the qualifications of an engineer, in designing, and those of a mechanic, in execution. The men who have followed this trade have controlled the training of their successors. In many cases the technical knowledge required bas been handed down from father to son, and there has been a motive of private interest to prevent its public dissemination. Moreover, the statement of the various principles involved in the process would require, besides manual experience, a degree of scientific knowledge which roll-turners do not usually possess; and, finally, any book on the subject, in order to possess real, practical value, would have to be so fully illustrated as to make it very costly to publish. Regarding my own experience, I may say that I served a six-

May 1, 1906

The Bougainville ore body was discovered in 1964 by a partnership of Conzinc Rio Tinto of Australia and New Broken Hill Consolidated Limited. The ore body is a porphyry copper in a fine-grained quartz diorite, which intrudes andesite volcanics and is located at an elevation of about 2, 000 ft in the Crown Prince Range of Bougainville in the Solomon Islands. Mineralization is predominantly chalcopyrite with some bornite and some gold and silver present. Rainfall in the area amounts to 200 in. (5. 08 m) per year. An active volcano is situated only 24 miles (38.4 km) from the mine, and all structures were designed to resist seismic shocks. An interesting and unique feature of the Bougainville operation was that the overburden was stripped with hydraulic monitors. Bougainville Copper, at 90,000 tpd, is the largest copper concentrator to be designed and constructed at one time; and besides the twin 54 in. by 74 in. Allis-Chalmers gyratories, it features seven 7 ft (2. 13 m) standard and fourteen 7 ft shorthead crushers, in addition to nine 18 ft diameter by 21 ft long (5. 5 m by 6. 4 m), 4250 hp, single -stage ball mills. During the design stage of the Bougainville primary crushing plant, several alternates were studied because the ore was expected to break with the production of large amounts of small-sized particles but with a minimum of fines. These alternates included two 54 in. by 74 in. gyratories with grizzlies, two 60 in. by 89 in. gyratories, and one 72 in. by 96 in. gyratory, the latter two installations without grizzlies. The two 54 in. units with grizzlies were finally selected as giving good reliability and the ability to handle the large amounts of small material in the feed. As originally installed, grizzly bars were set at 8 in. (203 mm); but, in an effort to perform more interparticle crushing in the primary and less rock-on-steel crushing in the secondaries and tertiaries, a test is underway (1976) to determine the effect of using 6 in. (152 mm) grizzly spacings (see write -up on Anaconda's crusher at Butte). The Bougainville ore is mined with 17 cu yd (13 cu m) shovels and hauled in 105, 170, and 210 st trucks to the crushers, which are equipped for two-side dumping. Up to 40% of the ore passes the grizzlies, which are equipped with splitters; and additional horizontal splitter bars are located directly above the spider caps. Because of the grizzlies, the crushers are supported by unique U-shaped enclosures, which are in turn supported by the end and center walls of the installation.

Jan 1, 1978

By J. F. Myers, F. M. Lewis

The paper reports the development of a large, slow speed ball mill closed circuited with a hydroscillator. This increased grinding efficiency 28 pct over conventional units.

Jan 1, 1950

By H. M. Wilten

THIS article presets a view of a problem encountered in petroleum refining in the deterioration of equipment used in condensation of vapors and cooling of liquids. Discussion is limited to the problems of shell- and tube-type exchangers and condensers. In this service shell- and .tube-type equipment is gradually displacing other types and, for this reason, its economic importance ill oil-refining practice is also increasing. Considering oil - refinery practice during the last two decades one can readily see many important improvements in the apparatus used. Briefly, the present equipment is safer, more efficient, and Ignore economical. Improvement in apparatus used for the condensation of distillates has, in my opinion, been less than that in other essential distilling apparatus. So it is hoped that this discussion will stimulate research among the producers as well as among the consumers of this equipment with a view to ameliorating this condition.

Jan 1, 1937

Correspondent. Must be able, by virtue of, connection, to forward; daily ands weekly, reports, outlining, conditions affecting economics of. industries, particularly the metallurgical, and chemical, industries. New. York, City. R-1982. Sales Lubrication. Engineer. Preferably with experience, as chief marines engineer familiar with internal-combustion; engines and, with, automobile trade. Must be good salesman, of goody appearance and be able to meet people. Middle West. Salary $27.00: to start. R71984.

Jan 12, 1919

ALLERTON S. CUSHMAN, Middletown, Ohio (written discussion*).¬ This subject is one to which I have given much thought and study and which I have frequently discussed informally with Mr. Cain and others. I have long been convinced that the gaseous elements, either combined or entrained (occluded), in steel play a much more important role than is ordinarily admitted. This is probably due to the difficulties encountered in the accurate quantitative estimation of gases, some of which Mr. Cain has referred to, as well as to the fact that, considered from the weight-percentage basis, gas content is measurable only in hundredths or even thousandths of 1 per cent. Volumetrically, however, the results ob-tained by modern research are startling, to say the least. Baraduc-Muller,1 as cited by Mr. Cain, pumped out of 1000-lb. ingots of basic Bessemer steel 2100 l. of gas. or about 75 cu. ft., at normal temperature and pressure, per ton of steel. In other words, we are to understand that Bessemer steel normally carries about fifteen times its own volume of gas. According to Baraduc-Müller's table of results, which is given here-with, carbon monoxide, nitrogen, and hydrogen are important consti-tuents of Bessemer steel, the latter gas being undoubtedly formed by the

Jan 11, 1919

By Reichmuth, Donald R.

Most brittle solids are relatively weak in tension and this weakness can be very significant in determining their performance in structures and excavations. Consequently, accurate knowledge of the tensile strength of brittle materials has long been recognized as important. In the past, measurements of the tensile strength of materials such as concrete, ceramics, and particularly rock have been hindered by problems encountered in fabricating test specimens and in accurately loading them. These difficulties have resulted in a scarcity of published tensile strength data. This can be readily seen in tabulations such as Wuerker's "Annotated Tables of Strength and Elastic Properties of Rocks.

Jan 1, 1968