Search Documents

By Thomas Brownfield

Development and production activity in Oklahoma during the year 1940 was of routine nature. Production, according to the Corporation Commission's figures, averaged 409,100 bbl. daily as compared with 421,000 bbl. for the year 1939. Discoveries were of minor importance except for the Cumberland pool in Marshall and Bryan Counties, in the southern part of the state. Maintenance of a relatively stable producing rate is attributable to the drilling of new wells and the recompletion of many old wells in the previously established producing areas. During the year 1785 new wells were drilled, a decline of approximately 10 per cent as compared with the previous year. Of the wells drilled, 962 were oil wells with a combined initial production of 241,000 bbl. daily, 172 were gas wells having aggregate capacities of 1205 million cu. ft., and 651 were dry holes. Wildcat activity increased 20 per cent over 1939 and 227 such wells were completed during the year; that isl 43 oil wells, 16 gas wells, and 168 dry holes. In addition to the new work completed, 603 wells were recorded as having been drilled deeper or plugged back to test new horizons; included were 334 producing wells with total initial production of 65,000 bbl. daily, 37 gas wells with initial aggregating 305 million cu. ft., and 232 abandonments. Footage drilled amounted to 4,730,000 ft., an average of 2650 ft. per well as com-pared with an average depth of 2600 ft. recorded the previous year. The principal new pools discovered as a result of the exploratory drilling were Cumberland; East Cromwell, in Okfuskee County, and Prague, in Lincoln County. At the end of the year Cumberland had 13 completed wells, which averaged 700 bbl. initial through tubing from the Simpson Bromide formation (Ordovician) at 4750 ft. East Cromwell had 10 wells with average initial of 435 bbl. in the Cromwell sand (Pennsylvanian) at 3460 ft. Prague had II wells with an initial average of 220 bbl. from the Senora sand (Pennsylvanian) at 3260 ft. There were notable extensions to the Dill pool, Okfuskee County, and to the Hewitt pool, Carter County. At the end of the year, 19 producing wells had been drilled in the former, with initials averaging 1000 bbl., and 63 wells averaging 150 bbl. daily in the latter. There were no notable changes in the policy of State conservation authorities with respect to proration. The Bureau of Mines recommendations for the year averaged 413,000 bbl. daily; the State author-ities fixed allowables at an average of 406,000 bbl. daily, while, as noted above, production averaged 409,100 barrels. The most important development in the older areas occurred in the following pools: Billings.—Seven oil wells with an average initial production of 2500 bbl. and two dry holes were completed during the year. Production from the Simpson horizon averaged 6025 bbl. daily as compared with 5950 the previous year. Production from this field has been almost steady since reaching its peak early in 1937. The major portion of the pool is efficiently operated as

Jan 1, 1941

By Thomas Brownfield

Development and production activity in Oklahoma during the year 1940 was of routine nature. Production, according to the Corporation Commission's figures, averaged 409,100 bbl. daily as compared with 421,000 bbl. for the year 1939. Discoveries were of minor importance except for the Cumberland pool in Marshall and Bryan Counties, in the southern part of the state. Maintenance of a relatively stable producing rate is attributable to the drilling of new wells and the recompletion of many old wells in the previously established producing areas. During the year 1785 new wells were drilled, a decline of approximately 10 per cent as compared with the previous year. Of the wells drilled, 962 were oil wells with a combined initial production of 241,000 bbl. daily, 172 were gas wells having aggregate capacities of 1205 million cu. ft., and 651 were dry holes. Wildcat activity increased 20 per cent over 1939 and 227 such wells were completed during the year; that isl 43 oil wells, 16 gas wells, and 168 dry holes. In addition to the new work completed, 603 wells were recorded as having been drilled deeper or plugged back to test new horizons; included were 334 producing wells with total initial production of 65,000 bbl. daily, 37 gas wells with initial aggregating 305 million cu. ft., and 232 abandonments. Footage drilled amounted to 4,730,000 ft., an average of 2650 ft. per well as com-pared with an average depth of 2600 ft. recorded the previous year. The principal new pools discovered as a result of the exploratory drilling were Cumberland; East Cromwell, in Okfuskee County, and Prague, in Lincoln County. At the end of the year Cumberland had 13 completed wells, which averaged 700 bbl. initial through tubing from the Simpson Bromide formation (Ordovician) at 4750 ft. East Cromwell had 10 wells with average initial of 435 bbl. in the Cromwell sand (Pennsylvanian) at 3460 ft. Prague had II wells with an initial average of 220 bbl. from the Senora sand (Pennsylvanian) at 3260 ft. There were notable extensions to the Dill pool, Okfuskee County, and to the Hewitt pool, Carter County. At the end of the year, 19 producing wells had been drilled in the former, with initials averaging 1000 bbl., and 63 wells averaging 150 bbl. daily in the latter. There were no notable changes in the policy of State conservation authorities with respect to proration. The Bureau of Mines recommendations for the year averaged 413,000 bbl. daily; the State author-ities fixed allowables at an average of 406,000 bbl. daily, while, as noted above, production averaged 409,100 barrels. The most important development in the older areas occurred in the following pools: Billings.—Seven oil wells with an average initial production of 2500 bbl. and two dry holes were completed during the year. Production from the Simpson horizon averaged 6025 bbl. daily as compared with 5950 the previous year. Production from this field has been almost steady since reaching its peak early in 1937. The major portion of the pool is efficiently operated as

Jan 1, 1941

By H. M. Beatty, T. L. Joseph, Gust Bitsianes

SUCCESSFUL blast-furnace operation depends upon securing an optimum balance between a number of important variables. This balance will vary somewhat from furnace to furnace in the same plant and with raw materials available in different plants. It is difficult to isolate the effect of any one variable unless it has a rather pronounced effect upon the efficiency of operation. The physical properties of iron ore and coke are known to affect the process, yet it is difficult to set up any definite yardstick by which these differences can be appraised. In recent years, whenever practicable, operators have taken steps to obtain better control over the absolute size and uniformity of size of the ore and coke. The size and physical character of the stone, however, have received comparatively little attention, emphasis being placed upon chemical composition, fluxing efficiency, and action as a desulphurizing agent. Since the stone occupies only about 10 per cent of the volume of the stock column, its influence upon permeability is less than that of the ore and the coke. The large pieces now used have a tendency to roll to the center and thus increase the permeability of this part of the stock column. Smaller pieces would be more effective in promoting the permeability of denser portions of the stock. The size and physical properties of blast- furnace stone are important also for reasons best understood by considering the results obtained by the crushing and the sizing of iron ore. Crushing ore to about 2 in. at Provo, Utah, and to about I in. in Alabama produced material somewhat less permeable to gases, even though sized. In spite of some sacrifice in permeability, the efficiency of the process was improved by crushing and sizing the ore, as indicated by a substantial saving in fuel and increased output. This saving in fuel is due in large measure to more thorough reduction of ore in the upper part of the furnace and to a corresponding decrease in the amount of carbon consumed prematurely above the tuyeres by the reaction CO2 + C = 2CO ? 70,080 B.t.u. [I] The physical properties of stone, its size and rate of calcination are important because they influence the rate at which C02 is released and the completeness of calcination before reaching a level in the furnace where the temperature does not exceed 1050°C. (1920°F.). Briefly, carbon dioxide from the limestone or from the reduction of ore may cause premature com- bustion of carbon above the tuyeres. Assuming that 1000 lb. of limestone is used per ton of pig iron, about 435 lb. of C02 will be liberated during calcination of a good grade of stone. If all this CO2 from the stone were to oxidize carbon prematurely, about 120 lb. would be consumed above the tuyeres in a heat-absorbing reaction. The amount of carbon thus consumed when a

Jan 1, 1942

By Donald H. McLaughlin

THE primary function of the mining engineer is to find mineral deposits and fuels in the accessible rocks of the earth and to recover them for the vast needs of our complicated civilization. On him has been placed the responsibility for the exploitation of the nation's and world's mineral resources. The degree to which the minerals of the earth have been utilized serves to an extent as a measure of man's material advancement, as well as an index of the relative strength of nations. The natural endowment of lands, varies greatly, but the intellectual energy of a people is revealed by the way in which they take advantage of their heritage of minerals or reach out to less developed regions by exporting their engineering skill as well as capital to secure the raw materials they need.

Jan 2, 1953

By A. T. Churchman

The deformation modes of rhenium have been identified as those typical of the hexagonal metals, titanium, zirconium, and beryllium whose c/a ratios, in common with rhenium, are less than ideal for close packing. Slip is observed on (1010), (1011), and (0001) planes and twinning on (1121), (1122), and (1012) planes. The very high rate of work hardening is believed to be associated with intersecting partial dislocations on two (1010) systems which can combine to form sessile barriers. If the stacking fault energy is low, as postulated by Seeger, these barriers should be strong and not easily bypassed by cross slipping. Such an explanation could also account for the very small temperature dependence of the yield stress which was observed. RHENIUM is interesting scientifically as a member of the group of high melting point hexagonal metals: titanium, beryllium, and zirconium with a c/a ratio less than that for ideal close packing. Unlike them, however, it work hardens at a very high rate. This rate is greater and continues to a much higher degree of deformation than for nickel, normally considered to have a high rate of work hardening. This paper presents experimental observations on the modes of deformation of rhenium and, by comparison with other hexagonal metals, some speculation on the cause of the high work hardening. MATERIALS Johnson, Matthey rhenium powder of both 99.9 pct and 99.5 pct purity, see Table I, was compacted at 10 tons per sq in., part sintered at 1350°C in vacuo, and finally arc melted in a "gettered" argon atmosphere arc furnace to produce small buttons. Little difference was observed in the as-cast hardness or working down behavior of the two purities suggesting that either silicon and potassium do not have a significant effect on the working properties of rhenium or they were lost during arc melting. SPECIMEN PREPARATION The cast structure was broken up by cold-rolling with inter-stage annealing at 1600o or 1800°C in a vacuum high-frequency furnace using a tungsten susceptor. Strip for tensile testing was taken from two thicknesses of material 0.011 and 0.064 in. The former with intermediate anneals at 1800°C had a grain size of 900 grains per sq mm, while the latter with inter-stage annealing at 1600°C had a grain size of 3600 grains per sq mm. A coarse grain size was obtained by secondary recrystallization in a half button cold-worked by 30 pct reduction. Annealing times of from half an hour to several hours at 2200° to 2600°C in a "gettered" argon atmosphere arc furnace1 resulted in grains of up to 2 mm diam.

Jan 1, 1961

By Nagel, Theodore

USE of oxygen in metallurgical operations was investigated by a committee of unusually able engineers more than ten years ago. A record of their work appeared under the title "The Use of Oxygen or Oxygenated Air in Metallurgical and Allied Processes," Serial 2502, Report of Investigations, U. S. Bureau of Mines. Shortly thereafter the A.I.M.E. published "Use of Oxygenated Air in Metallurgical Operations," based on a symposium at the New York meeting, February 1, 924. Quoting from the Bureau of Mines report In view of the many recent developments in oxygen manufacture, and considering the increasing cost and decreasing quality of our raw materials, the Bureau of Mines has taken the matter of the application of oxygen or oxygenated air to the metallurgical centers for consideration and has appointed an advisory committee to study the problem.

Jan 1, 1935

By Gardner F. Williams

These mines are situated in Griqualand West, which is now a part of the Cape Colony. The town of Kimberley is in latitude 28o40' South, longitude 25o10' East, about 640 miles northeast of Cape Town and 450 miles from Port Elizabeth on the east coast. It is connected with these towns by a railroad, which has been completed during the present year. The mines are located in a desert country, resembling the desert portion of Arizona. The elevation above sea-level is about 4000 feet. The climate is exceedingly hot during the summer months. Diamond Deposits.—There are four large diamond-bearing deposits at Kimberley, all lying within a radius of one and one-half miles, having the De Beers mine as the center. These are named the " Kimberley," " De Beers," " Du Toit's Pan," and " Bultfontein " mines. There is, also, directly west of the Kimberley mine, a small deposit, called " St. Augustiue," which has been prospected only, and

Jan 1, 1887

By James E. Lawver, James L. Wright

This paper discusses the design and calibration of a Faraday pail for measuring electric charge. The paper also shows that at least for two minerals, quartz and calcite, the phenomenon that Johnson termed "reversibility" can be explained in terms of the contact electrification between the minerals and the metal rotor of an electrostatic machine. Each year the free world produces about 13 million tons of mineral concentrates by electrical separation. However, despite the rather general acceptance of electrical concentration as an industrial process, research in this area has lagged far behind the efforts devoted to competitive processes such as froth flotation. The purpose of this paper is to describe the design and calibration of a Faraday ice pail for measuring charge density on mineral grains and to show some of its applications in the area of electrostatic and electrodynamic research. THE DESIGN AND CALIBRATION OF FARADAY PAILS FOR ABSOLUTE CHARGE MEASUREMENT The electric charge on mineral grains at a given time during an electrical concentration process is de- pendent on many factors and cannot, in general, be accurately calculated a priori. It is thus important to devise a method of measuring absolute charge. One method of measuring electric charge is to note the potential rise of an electrometer when charged particles drop into a Faraday pail. Two types of Faraday pail have been constructed and calibrated. The first type, Faraday Pail I (Fig. 1), is a vertical pail originally designed to measure the charge due to contact electrification between mineral grains and a metal rotor or due to conductive induction when mineral grains are passed over a rotating cylinder in the presence of an electric field. The second type, labeled Faraday Pail II (Fig. 2), is a horizontal pail designed to determine the charge distribution of mineral grains after they pass through the separating zone of the electrical concentrator shown in Fig. 4. The main advantage of the horizontal pail is its low head-room requirement and the long opening which enables the experimenter to sample the entire width of the stream of minerals being separated. The Faraday pails were calibrated in the following manner: A calibration head was constructed in the form of a hollow brass sphere that could be held in an insulated metal cylinder by vacuum (Fig. 1). The capacitance of the sphere was calculated by measuring the capacitance of the sphere and cylinder combined and that of the cylinder alone and subtracting the latter measurement from the former. The sphere was then charged to a known potential (V) and allowed to drop into the Faraday pail which was attached to a Keithley Model 610A electrometer. This instrument has an accuracy of 2% full scale and has

Jan 1, 1969

By K. I. Savage, S. C. Sun

This paper describes a process developed to recover coal, clays and pyrite from coal wastes. The process consists of fine grinding followed by coal and pyrite flotation which leaves the clays in the flotation pulp. A bituminous coal refuse containing 10% sulfur and 30% carbonaceous material was treated by this method to yield a coal product containing 4% sulfur, 10% ash; a pyrite product containing 45% sulfur (84% FeS2), 1% carbonaceous material; and a clay product containing 2% sulfur (3.5% FeS2). The coal yield was about 89%. The pyrite yield was about 77%. The process steps may be entirely flotation, or gravity separation (hydrocycloning) may be used to increase the pyrite : coal ratio in the flotation feed. Cost estimates for the process show a profit of $2.28 per ton of low pyrite grade refuse, but these do not include labor, maintenance, overhead and plant depreciation. The development of this process consisted of three parts: (1) exploratory tests, (2) op-timazation tests and (3) confirmatory tests. The objectionable qualities that sulfur imparts to coal have been commented upon from early times, and they have become more objectionable as the uses of coal have grown. In whatever form coal takes — raw, carbonized or gasified —the sulfur content remains objectionable, and therefore its compounds are removed as completely as possible. It has long been known that sulfur occurs in coal in different forms. In 1861, sulfur was said to exist in the state of sulfuric acid in combination with a base; in combination with iron as iron pyrites; as bisulfides of iron; and in combination with the organic elements of coal.' Pyritic sulfur is a term loosely used to cover the sulfur associated with iron in its various forms. The mineralogically recognized forms are pyrite (FeS2), pyrrhotite (Fe 1-x S) and marcasite (FeS2). The particle sizes of pyrites vary widely. Isolated grains of marcasite smaller than 15 microns have been found disseminated through coal.2 Hair-like "veins" of pyrite filling cracks in vitrain have been found. At the other extreme, lumps or nodules of pyrites large enough for removal by hand picking have been encountered. Organic sulfur, unlike pyritic sulfur, does not exist as discrete particles, but is instead intimately associated with the coal structure and thus it is impossible to remove it or reduce its concentration by physical or mechanical means.2 In the preparation of coal for its various markets, the pyrite minerals (pyrites) are separated from the raw coal feed. This separation process concentrates the pyrites in the tailings or other waste products. It would be desirable to recover these pyrites for three reasons: (1) Pyrites are potential sources of sulfur and iron. In 1967, for the fifth consecutive year, Free World consumption of sulfur exceeded production.3 Propelled by the shortage, the domestic price of sulfur has risen from $24 to $38 per long ton (bright). (2) The refuse, when placed in piles, becomes ignited. The pyrites (FeS2) bum, giving off SO,. Thus, the pyrites are a cause of air pollution. (3) Also, the pyrites undergo chemical reaction when exposed to air. The refuse is leached by waters which result in stream pollution due to the water-soluble iron and acidic reaction products. Coal refuse also contains coal minerals and clay minerals. Therefore, any process for recovering the pyrites must successfully separate them from the coal and clay minerals. In the study discussed here, ten different bituminous coal refuse samples were successfully upgraded in pyrite content. These samples represented a wide variety of coal waste materials from Pennsylvania and other states. The variabilities of the sulfur and coal contents are shown in Table I. The extremes are Sample J, a high sulfur-low coal, and Sample B, a low sulfur-high coal. Definitions of some of the symbols or terms used in this report are given below: Mesh size—Tyler standard mesh screen sieves with an opening based on the square root of two. Fe —Indicates iron, as determined by a stannous reduction-dichromatic oxidation method. S—Indicates sulfur, as determined by the ASTM "Eschka" method for sulfur in coal.

Jan 1, 1969

By Wilbur T. Stuart

TO assist the mining industry in attacking problems of water control, the U. S. Geological Survey has begun a program of research in mining hydrology. In certain fundamental respects water control is similar to development of water supplies from wells or to the drainage of agricultural lands, as many of the tools developed in recent years for quantitative ground-water problems are applicable, with modification, to mine-water problems. In 1952 a 30-day pumping test conducted jointly by the Eureka Corp. Ltd. and the Defense Minerals Exploration Agency provided an opportunity to gain knowledge concerning water movements around a flooded mine shaft. The methods of analyzing the data may be used as a guide for the evaluation of similar problems elsewhere. The Fad shaft of the Eureka Corp. is on Ruby Hill, 1 1/2 miles west of Eureka, Nev. The shaft was completed at a depth of 2465 ft in November 1947 at a site adjacent to the downfaulted block in which the ore was found. As the drift on the 2250 level progressed toward the ore zone, a large flow of water was encountered after the Martin fault was intersected. This flow exceeded the installed pump capacity, and an unsuccessful attempt to recover the shaft and the 2250 level was made in 1948.1, 2 Geology and Hydrology: The complex structure of Ruby Hill is that of an anticline broken first by thrust faulting and later by normal faults. The present orebody comprises several mineralized zones within a block of the Eldorado limestone of middle Cambrian age which was downfaulted 1400 to 1600 ft, and it may be related to a similar body mined at a higher level south of the Ruby Hill fault. At the depth of the largest zone of ore the block is roughly rectangular in shape, about 1000 ft wide and 1500 ft long, and dips about 30" NE, see Fig. 1. It is apparently bounded on the south by the Ruby Hill fault, on the east by the Jackson fault, on the north by the Martin fault, and the west by the Bowman fault. Within the block, but between the Ruby Hill and the Martin faults, are the Office and Adams Hills faults; west of the block and the Bowman fault are the Albion and Spring Valley faults. There are many conflicting reports concerning the water-yielding characteristics of the Eldorado limestone and the condition of the fault zones, that is, whether they are open or tight. However, the diamond-drill records indicate that open spaces as much as 2 or 3 ft across were encountered, and considerable cementing and lining of holes was necessary to maintain circulation of drilling fluid. There is also evidence that the Eldorado limestone was cavernous where it was mined in the early days south of the Ruby Hill fault. At the site of the Fad shaft the formations encountered from the surface down included the Pogonip limestone, Dunderberg shale, Hamburg limestone, and Secret Canyon shale. These formations did not yield large quantities of water to the shaft. The Pogonip limestone, which appears to be permeable and might yield water elsewhere, is above the water table in the vicinity of the shaft. The Secret Canyon shale, immediately overlying the Eldorado in some places but in most places separated from it by the Geddes limestone,3 is apparently tight and does not transmit water. During the 30-day test period the shale briefly confined the water in the underlying formations so that artesian conditions were observed in drillholes E and F, which are cased into the Eldorado limestone, whereas unconfined conditions were observed in drillholes B, C, and D, which were open to the shale. The Geddes limestone, which normally lies between the Secret Canyon shale and the Eldorado limestone, was not encountered in the Fad shaft. The Geddes, a flaggy, fractured limestone, is reported capable of yielding large volumes of water. Water stored in the interstices of this thin-bedded limestone within the Ruby Hill fault zone on the 1200 level of the Locan shaft drowned the pumps in 1923 when the Richmond-Eureka Mining Co. attempted to explore the area along the fault. Eldorado limestone was not encountered in the Fad shaft. In the ore-block area the Eldorado limestone was not entirely offset from other water-yielding formations by movement along the Bowman fault; therefore it may be hydraulically connected with the other formations. Adjacent to the Ruby Hill, Jackson, and Martin faults, the Eldorado lies in contact with other possible water-yielding formations. One of these, the Prospect Mountain quartzite, is separated from the Eldorado by thin, sheared, and broken beds of the Geddes within the Ruby Hill fault zone. A limited examination by the author of the Prospect Mountain quartzite in the Richmond mine at a higher level and south of the Ruby Hill fault indicates that the quartzite is poorly permeable. The monzonite mass south of the quartzite would be a further barrier to the flow of water. The poor permeability of this area is substantiated by records of levels at which water was encountered south of the Ruby Hill fault. In view of the normally low rate of ground-water recharge, if this desert area had been permeable, water levels could not have been maintained at altitudes of many hundred feet above the present water table west and north of Ruby Hill. Thus the ore-bearing block of Eldorado limestone is in contact with possible water-yielding rocks on at least two sides, and if the fault zones are possible conduits for water circulation the geologic and hydrologic conditions are suitable for the infinite-aquifer type of analysis as used and modified here. History of Pumping: During sinking of the Fad shaft a maximum pumping rate of 1500 gpm kept the shaft dewatered sufficiently, but in March 1948, after the 2250 level drift passed through the Martin fault into the Eldorado limestone, the pumps and shaft were flooded. Subsequently additional pump-

Jan 1, 1956

By D. L. McElroy

SAFETY in coal mining received especial attention by the public in general and the mining industry in particular during 1940 and early in 1941, owing primarily to the six explosion disasters which occurred last year with a total of 276 fatalities. This was the largest number of fatalities due to explosions in bituminous coal mines since 1928, when 347 lives were so lost. But facilities due to explosions have had a definite decreasing trend since 1907, in spite of bad years such as 1917, 1924, 1932, 1937, and 1940. Although the upswing in explosion fatalities in 1940 is lamented by all, none will admit it represents a trend and it will serve mainly to stimulate ways and means of further reducing these disasters.

Jan 1, 1941

By Edwin B. Johnson

The success of self-fluxed sinter in enhancing the operation of the blast furnace during the past few years has reasonably led to the assumption that the use of self-fluxed pellets might result in even greater furnace efficiencies. A great share of development work in agglomeration has been directed towards techniques related to the production of self-fluxed pellets, but no appreciable tonnage of self-fluxed pellets had been produced on a commercial scale until this past year when The Cleveland-Cliffs Iron Co. produced 35,000 tons of such pellets by the grate kiln system at the Republic mine during the period May 21-June 5, 1962.

Jan 3, 1963

By John T. Norton, R. E. Hiller

The tremendous increase in the use of metals that have been prcpared by the various cold-working processes during recent years has greatly stimulated the investigation of problems concerned with the fundamental nature of these processes. It has been observed in practice that different methods of bringing about the same dimension changes in a sample result in a rather wide range of properties. Cold working reduces the ductility of a metal, or what is perhaps more nearly correct, its "working capacity," and naturally the manufacturer wishes to produce an article that has as large a working capacity as possible, and to produce it with the smallest number of operations. It has also been known for some time that cold deformation produces a parallel alignment of the crystal grains of a metal, and that the type of this preferred orientation depends to some extent at least upon particular processes employed in the deformation. The present investigation has for its purpose the study of the relations between the various factors of a cold-working process and the preferred orientation of the metjal crystals resulting from this deformation. The work is chiefly confined to a study of cold-drawn seamless tubing. Preparation of Samples The tubing samples used in this investigation were made of steel having a carbon content of 0.10 to 0.20 per cent, and were drawn on a standard type of draw bench. In order to obtain the large reductions, the annealed stock was coated with lead, for purposes of lubrication. The reductions of area stated refer to reduction from the annealed condition without intermediate heat treatment. The cold work was done as nearly as possible at room temperature. The samples of wire and strip used for purposes of comparison were of steel of approximately the same carbon content and were prepared in the manner indicated. X-ray Method of Investigation The condition of preferred orientation in cold-worked samples is best investigated by the X-ray method that employs a small circular beam of * Assoriate Professor of Physics of Metals, Massachusetts Institute of Technology. t Graduate Student, Department of Metallurgy, Massarhusetts Institute of Technology.

Jan 1, 1932

By A. R. Troiano, A. B. Greninger

There is need for an adequate working hypothesis that would describe at least qualitatively the crystallographic mechanism for the transformation from austenite to martensite in steel. A general theory would not only be of great assistance in the correlation of existing data and in planning future experimentation, but would also form the basis for an eventual explanation of the property changes that accompany lattice transformations. The mechanism of martensite formation described in the following pages is the outcome of two new experimental determinations: (1) the accurate evaluation of the lattice relationship between austenite and individual crystals of martensite, and (2) the measurement and analysis of the change in position that a volume of austenite undergoes when it transforms into a crystal of martensite. For this latter study, the stereographic analysis of shear was employed; this method greatly simplifies the solution of lattice-shear problems, and some space is devoted to its description. Lattiice Relationships and Habits PREVIOUS WORK The lattice relationships between austenite and martensite in carbon steels have been studied by Kurdjurnow-and Sachs,' and by Wassermann;2 and in iron-nickel alloys by Nishiyama.3 Wassermann,2 and Mehl and Derge.4 The studies by Kurdjumow and Sachs and by Wassermann were made on single (austenite) crystals of quenched 1.4 pct carbon steel, and the results of these two independent studies agree closely with the postulated lattice relationships: (III)r||(0ll)a [101]r [111]a [1] Both Nishiyama and Wassermann worked with an alloy of iron plus 30 pct nickel (all austenite at room temperature), and "martensitic alpha" was formed by cooling in liquid air. They agree that the lattice relationships for these conditions are: (lll)r||(011)a [112]r[011]a [2] Mehl and Derge worked with a range of iron-nickel alloy compositions centered about 30 pct nickel. They concluded that when the transformation takes place near room temperature or above, relationship [l] holds, but if the same specimen is made to transform at -195°C, relationship [2] obtains;intermediate temperatures evidently produced a combination of these two relationships. Sachs and co-worker~,1,7 as well as Nishiyama,3 have proposed transformation mechanisms for martensite formation.* Both of the mechanisms picture the transformation as initiated by shearing movements along the octahedral [Ill] plane of austenite, followed by suitable expansion and contraction to complete the transformation. These mechanisms have been described and commented upon by Mehl, Barrett, and Smith,8 Mehl and Derge,4 Wassermann,2 and others, and generally accepted by investigators in this field. Greninger and Troiano9 have recently published the results of a detailed study of the shapes and orientation habits of martensite crystals in plain-carbon and nickel steels. They found that, contrary to previous assumptions, martensite plates form not along the octahedral planes but along austenite planes of very high indices; these results were in line with those of previous studies of martensite reactions in nonferrous alloy systems by Greninger and coworkers.6,10 Greninger and Troiano concluded that the transformation theories of Kurdjumow and Sachsl and of Nishiyama3 are untenable. Phragmén11 reached a similar conclusion. EXPERlMENTAL METHODS The object of this particular study was the evaluation of (1) lattice relationship between austenite and martensite, and (2) relationship between the martensite lattice and the martensite plate. The technique used for solving these problems was similar to that used by Greninger6 on martensitic structures in 8 copper-aluminum alloys. Briefly, the method consists of grinding and polishing a specimen on a surface parallel to an individual martensite plate and thus exposing a single martensite crystal for an area of l to 3 mm. The orientation of this exposed martensite crystal is then determined by means of a back-reflection Laue X ray pattern.12 Another pattern is obtained from the matrix crystal, and a stereo-graphic plot of data from these two patterns then provides the solution to the problem. It is necessary to repeat this process on several crystals in order to determine whether or not the solution is unique.

Jan 1, 1950

By Jean Howard

RECENT attempts to produce secondary recrystalli-zation in high-purity iron have given conflicting results. Coulomb and Lacombe1'2 did not find it but Dunn and Walter3,4 did. The latter workers have stated that (100) [001] and/or (110) [001] orientations develop depending on the oxygen content of the annealing atmosphere. This Technical Note records results which are in agreement with Dunn and Walter in so far as it shows that secondary recrystallization can be produced in high-purity iron, but does not confirm that both types of orientation are obtainable. Similar observations have been made on chromium-iron and molybdenum-iron, although when this technique is used on 3 1/4 pct Si-Fe, both types are obtained as in the work of Dunn and alter.' Pure iron strip was cold-rolled from sintered compacts prepared from Carbonyl Iron Powder-Grade MCP of the International Nickel Co. (Mond) Ltd. The powder contains about 0.5 pct 0, 0.01 pct C, 0.004 pct N, (0.002 pct S, $0.005 pct Mg and Si, and 0.4 pct Ni—that is, it is substantially free from metallic impurities other than nickel, which is thought to be unimportant in the present work. The iron powder was (a) pressed at 25 tons per sq in. into blocks measuring 3 by 1 by 0.3 in., (b) deoxidized in hydrogen (dewpoint -60°C) by heating first at 350°C and then at 600° C until the dewpoint returned to -60°C at each temperature and (c) sintered in hydrogen (dewpoint -40°C) at 1350°C for 24 hr. (when dewpoint is referred to in this Note, it is the value as measured on the exit side of the furnace). The sintered compacts were cold-rolled to 1/8 in., annealed in hydrogen (dewpoint -60°C) at 1050°C for 12 hr and cold-rolled to 0.004, 0.002, and 0.001 in. with inter-anneals at 900°C for 5 hr and a final reduction of 50 pct. Final annealing of strip between alumina or silica plates at 875" to 900°C in hydrogen with dewpoints of -20°, -55" and -80°C produced secondary grains with the (100) in the rolling plane; the extent of secondary recrystallization was greatest when the dewpoint was -55°C. Annealing in a vacuum of 2 x 10"5 mm Hg at the same temperature produced no secondary recrystallization at all. With strip thicker than 0.002 in. very few secondary crystals developed whatever the conditions of annealing. Using a processing schedule somewhat similar to that described above, secondary recrystallization was produced in two bcc alloys of iron, viz. 80 pct Fe + 20 pct Cr and 96 pct Fe + 4 pct Mo. The former was reduced to final thicknesses of 0.001 to 0.004 in. and the latter to final thicknesses of 0.001 to 0.016 in. With the chromium-iron, a final anneal at 1250°C (found to be the most effective temperature for developing secondary crystals in the 0.004-in material) with a dewpoint of -25°C produced a greater degree of secondary recrystallization than with dewpoints of -50°C or -20°C. Secondary crystals developed in strips of all thicknesses from 0.001 to 0.004 in. Final annealing in vacuum produced no secondary crystals at all. For the molybdenum-iron a temperature of 1200°C was most effective. It was found that a dewpoint of -50°C during the final anneal gave better results than a dewpoint of -25 "C on the 0.008 in. material. Final annealing in vacuum gave slightly worse results than annealing in hydrogen with a dew-point of -50°C. Secondary crystals were developed in strips of all thicknesses up to 0.008 in. The experiments show that the extent of secondary recrystallization is a maximum for certain critical values of oxygen content of furnace atmosphere and annealing temperature, and that these values are different for different alloys. The thinner the material, the less critical these values are. The general conclusions are that secondary recrystallization can be obtained in high-purity iron, chromium-iron, and molybdenum-iron, using a processing schedule similar to that which will cause the phenomenon to take place in high purity 3 1/4 pct Si-Fe. Unlike the silicon-iron, however, only the (100) (0011-- orientation has been produced in these alloys, irrespective of the temperature of final annealing and the oxygen content of the furnace atmosphere. The information used in this Note is published by permission of the Engineer-in-Chief of the British Post Office.

Jan 1, 1962

FOREIGN WAR RELIEF COMMITTEE Chairman, MRS. JESSE SCOBEY The task of the committee since Oct. 17, 1918, has been to stimulate and foster interest in the work of the Dispensary in France, to aid and further the work, and to that end has centered on the inauguration of an "Engineers' " day, once a week, at the headquarters of the American Fund for French Wounded, where members of the Auxiliary might join in sewing for this "Dispensary of the New York Section of the Woman's Auxiliary to the A. I. M. E.," recently established at Briey, France. Letters and pledge forms asking for workers were sent to all members of the Auxiliary in New York City and vicinity, and a most gratifying response has assured the success of the undertaking. The meetings in December, pending the completion of better working facilities at Fund headquarters, were held at the home of Miss Madeline P. Stone, to whom the committee extends its grateful thanks for her hospitality large, well-equipped room at Fund headquarters has now been assigned to the committee for Tuesday of each week, from 10 a. m. to 5 p. m., with Mrs. Percy E. Barbour of the committee as director of work room. All members of the Auxiliary and others whose interests are with the mining profession will be welcome on "Engineers'" day-Tuesdays-at 73 Park Ave.

Jan 2, 1919

By Donald Barton

THE theory of gravitation is based on Newton's law that any two bodies exert a mutual attraction which is proportional to the product of their masses and inversely proportional to the square of the distance between them; i. e. A= K MM/R2 (1) where K is a constant, M and m are the respective masses of the two bodies, and R the distance between them. In the earth's gravitational system, the earth is one of the bodies; the other may be any body within or without the earth. In theoretical discussions and calculations in regard to gravity, that other body usually is taken as a unit of mass: in the C. G. S. system, a body of one gram in mass.

Jan 1, 1928

By John Vasey

A shaft of 1690 m depth is currently being sunk to exploit a large copper sulphide orebody. The primary crusher chamber, main pump chamber and the other excavations on the crusher level were developed from the shaft during the sinking operation. The maximum principal stress is horizontal and has a magnitude twice that of the vertical stress. It increased linearly with depth and on the elevation of the crusher level, 1613 m below surface, the stresses induced by mining can exceed the strength of the rock. The development of a workable crusher level layout, and a crusher chamber design and support system are described. Excavation and support of the workings are detailed and a comparison of expected and actual results is made.

Jan 1, 1983

By John T. Dickman, Ralph E. O’Dette

Chemical Abstracts Service (CAS) is in the process of evolving a computer-based information system which will process all of the material selected for abstracting in the area of chemistry and chemical engineering and its related fields such as the earth sciences and technologies. This system is already operational to some extent and is expected to be fully utilized by 1971. The objective of CAS is to make chemical and related information more readily available, more usable and more used. Chemical Abstracts handle some 5000 abstracts weekly from 13, 000 journals and patents from 25 nations. These cover all of the 80 CA subject sections which relate to chemistry and also extend into areas of interest to geologists, mineralogists, and mining engineers. In this way, CAS fulfills its objective of complete coverage of its major fields, informative abstracting, and indexing to maximum specificity. The concept of a computer-based information system is that of a single machine-language data base into which the results of intellectual analysis of the literature are entered and from which computer programs produce a variety of publications and services applicable to the needs of a wide range of users.

Jan 1, 1969

By Charles H. Moore

In the study of the properties of rutile pigments it became apparent several years ago that certain physical and optical properties could not be determined on particles of pigmentary size. Since reflected light is the dominant type which reaches the eye from small particles, the true color of pure rutile was not known. Most rutile pigments are acicular in habit, elongated parallel to the "c" axis. It was considered important to know the nature and tone of light transmitted, for example, by a basal plate. Further, as shown by spectrophotometric curves, there is a very strong absorption of light of 4000 k as measured on particles with random orientation. It would be interesting to see whether this absorption position varied with predetermined and selected orientations. Also, since the behavior of titanium pigments in a vehicle is important, a knowledge of the surface wettability of single crystals by various media should prove very fruitful. Finally, the optical properties of rutile are such that it should show, in a single pure crystal, greater fire and brilliance than the diamond. Mineralogists had long speculated that this would be the case and curiosity was strong to produce a single crystal large enough to cut.

Jan 1, 1949