Search Documents

By H. E. Exner

This article is a critical review of the influence of surface preparation on crack formation at Vickers indentations in the test used by Palmqvist3-7 to evaluate the toughness of cemented carbides. Experimental results are presented which clearly show that grinding introduces compressive surface stresses into the cobalt phase and thus reduces the crack length. The deformed surface layer is removed by polishing and a stress pattern is approached corresponding to that in the bulk material. Cracks of maximum length are characteristic of this stress state. Deformation stresses can be removed by annealing above 800°C. On the basis of these results , sample preparation for the crack length test can be simplified, the accuracy of measurement is improved, and a simple and significani parameter is found to describe crack resistance of cemented carbides. FOLLOWING suggestions by Ammann and Hinniiber,1'2 Palmqvist3-7 developed a method for testing the toughness of cemented carbides using as a measure the sum of crack lengths at the four corners of a Vickers hardness indentation. This method has several advantages over the bend test commonly used in carbide technology: a) specially formed samples are unnecessary; b) sufficient information can be obtained from one sample; c) the scatter is relatively small; d) the range of actual values for commercial cutting alloys is wide. Thus, this test is both cheaper and more precise than the bend test. Nevertheless, Palmqvist's method is not widely used, mainly for two reasons: a) The relationship between crack length and the technological properties of the material (wear and shock resistance) is not clear. b) The crack length is strongly dependent on surface treatment. It is necessary, therefore, that surface preparation be very precise and reproducible, conditions usually hard to obtain. While any other simple mechanical test has this first drawback, the second became crucial in the application of the crack length method as a practical test. The reasons that this drawback could not be eliminated are, in our opinion, misleading and inconsistent interpretations of the influence of surface preparation on the crack length given in literature. In the following, after a short review of previous experimental results the interpretations given by different authors,4?'-11 cf. Table I, are discussed critically and a consistent explanation is presented on the basis of which improvements of the method of crack length testing are proposed. 1) PREVIOUS EXPERIMENTAL RESULTS In his first attempt to use the cracks at Vickers impressions as a quantitative measure of the toughness of cemented carbides, palmqvist3 calculated the work necessary to initiate cracks by the formula: Sk =k.Pk. [I] where k = numerical constant = 6.49, Sk = critical work to initiate cracks (gf cm), Pk = critical load (load necessary to initiate cracks) HV = Vickers hardness (kp per sq mm). The difficulties involved in experimental determination of the critical load were overcome by the observation that a linear relation holds between the applied load and the sum of the crack lengths at the four corners of the indentation. This linear function, given by Eq. [2] below, was confirmed by Dawihl and Alt-meyer9and by our experiments, see Fig. 1: I = a1.P +a2 [2] where 1 = sum of the crack lengths at a Vickers indentation, P = applied load, al, a2 = parameters dependent on the toughness of the alloy and the surface preparation. The critical load, Pk, is now given by a2, which can be obtained by extrapolating the load vs crack length line to zero crack length, see Fig. 1. This simple relationship, Eq. [2], led Palmqvist1,7 to a parameter which was more reproducible and easier to obtain experimentally than the critical work: the work, S300, put into the sample to produce an average crack length of 300 µm per indentation. This parameter is calculated using the formula: where the load, P3oo, giving a crack length of 300 µm, can be taken from the load-crack length plot, Fig. 1,

Jan 1, 1970

By Walter Miller

ALTHOUGH confident of its ability to meet any demands which may be made, the petroleum refining industry is not complacent about the situation and realizes that the quantities of petroleum products to be furnished are so enormous and so far beyond what was previously estimated that the full co-operative effort of the industry must be exerted. Establishment by the President in May of the Office of Petroleum Coordinator for Defense with Secretary of the Interior Ickes at its head, plus the formation of the Petroleum Industry Council for Defense, in November, provide the channels for united endeavor within the industry and the means for gearing that endeavor within the industry and the means for gearing that endeavor in full harmony with the nation?s needs. Great strides have been made and a rapid understanding of the situation and the magnitude of the task is being attained by all concerned.

Jan 1, 1942

By Samuel S. Wyer

The following abbreviations hare been used in the text: Am. Mfr. and Iron World. American Manufacturer and Iron World, Pittsburg, Pa. Can. Min. Rez;. Canadian Mininy Review, Ottawa, Can. Cuss. Mag. Cassier's Mayazine, New York, N. Y. Col. Eng. Colliery Engineer, Scranton, Pa. Col. Guard. Colliery Guardian, London, Eog. Eng. and Min. Jour. Engineering and Mining Journal, New York, N. Y. Eng. News. Engineering News, New York, N. Y. Engr. Engineering, London, Eng. J. I. and 8. I. Journal of the Iron and Steel Institute, London, Eng. Jour. W. Soc. of Engrs. Journal Western Society of Engineers, Chicago, Ill. Lond. Eng. The Engineer, London, Eng. Mines and Min. Mines and Minerals, Scranton, Pa. North of Eng. I. M. E. North of England Institute of Mining Engineers, Newcastle-on-Tyne, England. Oester. Zeitsch f. Berg u. Hüt. Oesterreichische Zeitschrift für Berg-und Hittenwesen, Vienna, Austria. Pract. Engr. Practical Engineer, London, Eng. Proc. I. C! E. Proceedings Institution of Civil Engineers, London, Eng. Trans. A. I. M. E. Transactions American Institute of Mining Engineers, New York, N. Y. Trans. A. S. M. E. Transactions American Society Mechanical Engineers, New York, N. I!. Duns. Fed. I. M. E, Transuctions Federated Institute Mining Engineers, Newcastle-on-Tgne, England. Trans. L 31. E. Transactions Institute Mining Engineers, Newcastle-on-Tyne, England.

Jan 1, 1907

By C. G., Fink

The dissolution of gold by cyanide solutions was studied by determining the time required for the solvents to dissolve gold leaf. Minute traces, even 0.5 ppm, of sulphide ion retard the dissolution of gold, and this behavior cannot be accounted for by the presently accepted hypotheses involving oxygen-depletion or thiocyanate formation. On the other hand, traces of the salts of lead, bismuth, mercury, and thallium considerably accelerate the dissolution. The beneficial effect of lead is dependent upon the pH and cyanide ion concentration of the solution.

Jan 1, 1950

By Hiland G. Batcheller

HISTORY shows that the nation which makes the most steel is the most likely to win wars. Today the course of war shows that the nations which get there first with the most steel of the right kind will be the ones to win. Not only the most steel, mind you, but the right kind. Adequate production, which was enough for victory before the days of totally mechanized warfare of 1943, must now be accompanied by still better quality as well as more effective distribution. Further, both production and distribution must be flexible enough to permit rapid shifts from one weapon to another for use in varying elements in varying geographical areas. Thus the problem of making enough steel of the right kind at the right time in the face of changing requirements dictated by experience has been and will remain highly complex. This does riot permit us to ease our restrictions on nonessential use. War is a complex business, like the job of making steel for war. Each time we solve one problem, another pops its head up. Yet we are making some progress.

Jan 1, 1943

[59H1-Water Law and Its Significance to the Mining Industry by Wells A Hutchins 59H2-Relation of Land Subsidence to Groundwater Withdrawals in the Upper Gulf Coast Region, Texas by Leonard A Wood and A G Winslow 59F3-Hydraulic Mining of Gilsonite and Its Application to Coal Mining by J H Baker 59H4-Recovery of Phosphates by In Situ Fluid Mining by Sylvain J Pirson 59F5-Coal Cleaning Plant Design for Minimum Operating Labor by Wm M Bertholf and John D Price 59F6-Coke Combustibility A Neglected Characteristic by J D Price 59B7-Union Carbide's Uranium Operation at Maybell, Colorado by K W Lentz and F T Temple 59H8-A Rapid Method for Estimating Alumina in Feldspathic Sands by Hugh H Bein 59H9-Water Laws as Related to Dredging in Idaho by Robert A Lothrop, Richard B Porter, and Robert P Porter 58B19-Separation and Washing of Alumina Process Residue by Morton Handelman 59B11-Feed Preparation and Froth Modification for Fatty Acid Flotation by Carl C Martin and Burt C Mariacher 59B12-Design Requirements for Tailing Disposal in the Southwest by E Vern Given 59B13-Semi-Dome Shaped Buildings for Bulk Storage by Edward E Ives and William L Payne]

Jan 1, 1961

By Don Masson

MUCH has been written and many prophecies made on the subject of plastics as a replacement for metal, and the extent to which these materials will compete with each other for peace- time markets. (Metal is used in a broad sense to include all types.) But although certain synthetic resin materials have made considerable headway in war production, this change to plastics can hardly be regarded as a serious threat to the mining and metallurgical industries. Even today, the total yearly tonnage of plastic materials is approximately only 1 per cent of that of steel, and only a small fraction of this might be considered as actually replacing steel. However, these figures must not be taken as indicating that the importance of plastics in fields hitherto considered exclusively the territory of metals is negligible-far from it. Considering the comparatively minute tonnage of plastics now being produced in comparison to the output of metals, the number of applications where plastics have augmented or aided the sale of metals is considerable.

Jan 1, 1944

By Harrison Schmidt

Since the U. S. Geological Survey published the data on the Central Mining District collected by Lindgren and Gratonl and by Paige2 much new information has been obtained by development and mapping, but none of it had been published until recently when Kniffin3 published on Fierro, Lasky4 on the Ground Hog mine, Thorne5 on Santa Rita and Landon6 filed a thesis on the Fierro-Hanover-Santa Rita area at the University of Chicago. During the years 1927-1930 much of the writer's time was spent in mapping the geology and ore deposits of this district, particularly in the area of the zinc deposits at Hanover. Some of the data collected are presented here. Previous publications have been freely drawn upon and additional data used that were generously supplied by L. M. Kniffin, Wilfred Wright and Gerald Ballmer. Thanks are due Augustus Locke, Samuel G. Lasky, Kniffin, Wright and Ballmer for suggestions and critical readings of the manuscript, and to the Empire Zinc Co. (a subsidiary of the New Jersey Zinc Co.) for the privilege of publishing material compiled largely at its expense. The relation of the Central or the Santa Rita-Hanover-Fierro district to the Silver City district is shown on Paige's geologic map in the Silver City folio.7 Granodiorite porphyry and quartz-monzonite porphyry

Jan 1, 1935

By Harrison Schmidt

Since the U. S. Geological Survey published the data on the Central Mining District collected by Lindgren and Gratonl and by Paige2 much new information has been obtained by development and mapping, but none of it had been published until recently when Kniffin3 published on Fierro, Lasky4 on the Ground Hog mine, Thorne5 on Santa Rita and Landon6 filed a thesis on the Fierro-Hanover-Santa Rita area at the University of Chicago. During the years 1927-1930 much of the writer's time was spent in mapping the geology and ore deposits of this district, particularly in the area of the zinc deposits at Hanover. Some of the data collected are presented here. Previous publications have been freely drawn upon and additional data used that were generously supplied by L. M. Kniffin, Wilfred Wright and Gerald Ballmer. Thanks are due Augustus Locke, Samuel G. Lasky, Kniffin, Wright and Ballmer for suggestions and critical readings of the manuscript, and to the Empire Zinc Co. (a subsidiary of the New Jersey Zinc Co.) for the privilege of publishing material compiled largely at its expense. The relation of the Central or the Santa Rita-Hanover-Fierro district to the Silver City district is shown on Paige's geologic map in the Silver City folio.7 Granodiorite porphyry and quartz-monzonite porphyry

Jan 1, 1935

Since the U. S. Geological Survey published the data on the Central Mining District collected by Lindgren and Gratonl and by Paige2 much new information has been obtained by development and mapping, but none of it had been published until recently when Kniffin3 published on Fierro, Lasky4 on the Ground Hog mine, Thorne5 on Santa Rita and Landon6 filed a thesis on the Fierro-Hanover-Santa Rita area at the University of Chicago. During the years 1927-1930 much of the writer's time was spent in mapping the geology and ore deposits of this district, particularly in the area of the zinc deposits at Hanover. Some of the data collected are presented here. Previous publications have been freely drawn upon and additional data used that were generously supplied by L. M. Kniffin, Wilfred Wright and Gerald Ballmer. Thanks are due Augustus Locke, Samuel G. Lasky, Kniffin, Wright and Ballmer for suggestions and critical readings of the manuscript, and to the Empire Zinc Co. (a subsidiary of the New Jersey Zinc Co.) for the privilege of publishing material compiled largely at its expense. The relation of the Central or the Santa Rita-Hanover-Fierro district to the Silver City district is shown on Paige's geologic map in the Silver City folio.7 Granodiorite porphyry and quartz-monzonite porphyry

Jan 1, 1935

By Harrison Schmidt

Since the U. S. Geological Survey published the data on the Central Mining District collected by Lindgren and Gratonl and by Paige2 much new information has been obtained by development and mapping, but none of it had been published until recently when Kniffin3 published on Fierro, Lasky4 on the Ground Hog mine, Thorne5 on Santa Rita and Landon6 filed a thesis on the Fierro-Hanover-Santa Rita area at the University of Chicago. During the years 1927-1930 much of the writer's time was spent in mapping the geology and ore deposits of this district, particularly in the area of the zinc deposits at Hanover. Some of the data collected are presented here. Previous publications have been freely drawn upon and additional data used that were generously supplied by L. M. Kniffin, Wilfred Wright and Gerald Ballmer. Thanks are due Augustus Locke, Samuel G. Lasky, Kniffin, Wright and Ballmer for suggestions and critical readings of the manuscript, and to the Empire Zinc Co. (a subsidiary of the New Jersey Zinc Co.) for the privilege of publishing material compiled largely at its expense. The relation of the Central or the Santa Rita-Hanover-Fierro district to the Silver City district is shown on Paige's geologic map in the Silver City folio.7 Granodiorite porphyry and quartz-monzonite porphyry

Jan 1, 1935

By J. S. Koehler, F. Seitz

THE dislocation theory of plastic flow originated in 1928, when Prandtl1 suggested that the internal damping of metals of plastic origin might arise from the motion of a crystalline imperfection. Following this, Dehlinger2 employed a similar imperfection in a theory of recrystallization. The first detailed theoretical discussions were those of E. Orowan3 and G. I. Taylor4 in 1934. The resulting theory was gen- eralized by J. M. Burgers5 in 1939. Mott and Nabarro, in England, and Seitz and Read,6 in the United States, started an extensive examination of the atomic theory of dislocations in the period between 1939 and 1941. However, this development was arrested by the mar and was not taken up again until after 1945. Since 1946, the field has been the object of very intense activity, particularly in the United States and England. Dislocations are beautiful and intricate imperfections; they are sufficiently complicated to account for the great variety of phenomena encountered in the field of plastic flow. Above all, the dislocation concept enables us to understand how a metal or other plastic solid can deform inelastically under very small stresses at temperatures far below the melting point. Suppose we attempt to shear a perfect crystal plastically. This can be done by sliding one entire atomic plane simultaneously through one atomic distance with' respect to the near-

Jan 1, 1954

IRON AND STEEL COMMITTEE ALBERT SAUVEUR, Chairman. A. A. STEVENSON, Vice-Chairman. HERBERT M. BOYLSTON, Secretary, Abbot Bldg., Cambridge, Mass. John Birkinbine, William Kelly, J. S. Unger, William H. Blauvelt, Charles Kirchhoff, Felix A. Vogel, James Gayley, Richard Moldenke, Leonard Waldo, Henry D. Hibbard, Joseph W. Richards, William R. Walker, Henry M. Howe, C. F. W. Rys, William R. Webster, Robert W. Hunt, E. Gybbon Spilsbury, Frederick W. Wood. J. E. Johnson, Jr.,

Jan 1, 1914

By Holbrook Botset

EXPERIMENTS performed in this laboratory on the flow of gas-liquid mixtures through unconsolidated sands have been described and discussed in an earlier paper.4 In these earlier experiments a definite relationship was found between the liquid saturation of a sand and its permeability to the liquid or gas phase. Furthermore, the nature of the sand, the permeabilities of the sands over a range between 17 and 260 darcies, appeared to have a negligible effect upon the saturation-permeability relation. Likewise experiments indicated that the viscosity of the liquid, or the substitution of an immiscible liquid for the gas phase, had only a very slight effect on the permeability-saturation relation. This con-clusion has since been definitely confirmed by the experiments of M. C. Leverett3 on the flow of oil and water through unconsolidated sands. The sands used by Leverett were of very low permeability (between 6.8 and 1.04 darcies), while the oil-water viscosity ratio varied between 90 and 0.057. Since the sands that constitute petroleum reservoirs are largely con-solidated, although of widely varying degrees of consolidation, it was desirable to extend the experiments on gas-liquid mixtures to consolidated sand. In the study of consolidated sands additional variables are involved, but for the initial experiments the only new variable to be intro-duced was the cementing material.

Jan 1, 1939

By AIME AIME

THE Hazleton district of the Pennsylvania Anthracite Region will be the scene Oct. 14 and 15 of the fall meeting of the Coal Division and the Pennsylvania Anthracite Section. Here, coal mining has been active for more than 100 years and hereabouts industrial necessity inspired the numerous inventions of the Pardees, Eckley B. Coxe, a former A.I.M.E. president, and the Marltles, who contributed much to the success of the Institute in its early days, as well as to the upbuilding of modern methods in the anthracite and bituminous industries. Headquarters will be the Altamont Hotel, Hazleton, Pa. There will be two technical sessions Friday, registration preceding the first which is scheduled for 11 a.m. to 1 p. m. The second will be called at 2:30 p.m. Saturday is reserved for mine and plant visits, with golf and tennis after luncheon for those so inclined. The ladies are cordially invited to the meeting and arrangements have been made for their participation in much of the program. The chairmen of the committees preparing for the meeting are: Donald Markle, president, Jeddo-Highland Coal Co., General Committee; R. E. Hobart, mechanical superintendent, Lehigh Navigation Coal. Co., Committee on Visits and Inspections; H. D. Kynor, general manager, Northumberland Mining Co., Committee on Programs and Papers; B. H. Stockett, general manager, Weston; Dodson, Inc., Reception Committee.

Jan 1, 1932

By E. J. Eisenach, W. E. Jones

SAFETY and industrial hygiene have always been recognized as highly important in company policy, and the co-operative support of the company officials and entire plant personnel has contributed largely to the present success of the Company's program in this field. Growth has necessarily been slow, and dependent, at times, on trial and error but the program in its present form combines the regulations, working methods, and equipment that have proved their value under actual operating conditions. Every effort is made to keep the program on a practical basis. Continuous experimental work is carried on in conjunction with the health and safety program, with resultant periodic changes for improvement. As a proof of accomplishment, in 1945 the frequency and severity rates for accidents were the lowest in the history of the operation. A full-time safety engineer was employed in 1933 and an assistant safety engineer in 1936. During the following year a stenographer was employed in the office and a safety inspector was added for the mine. During the gradual expansion of operations that was climaxed by

Jan 1, 1946

By John Dasher

Extrapolation is a useful technique, but it can be overdone. Seldom is it justified to study over a range of 1 to 6 and extrapolate the results to 150,000. It is especially dangerous if the extrapolation is based on a false assumption. The authors assume settlers scale-up by residence time rather than by area, admit their result (a settler depth of 7 m) is "unreasonable" and suggest longer, wider, shallower settlers might be better. Various authors have noted for a copper-LIX system a total flow basis of 2 gpm per sq ft for sizing settlers. The results of this are compared with those in the paper in [Table 7]. The authors note that flooding of their settlers was never approached. Thus the smallest unit calculated is understandably twice too big. The largest however, is 5% of the required size. I note that the figures in [Table 6] for 1/min/cm2 are based on plan area rather than cross section as titled and are wrong by l0 4. A flow of 2050 1/min/cm2 is about Mach I. It is also 10 5/3 or 46.5 times that of the little one, although the abstract says the design was based on constant flow rate per unit cross section.

Jan 1, 1977

By George A. Komadina

From its modest beginning in 1957 with one mill grinding section handling 3000 tpd Pima has steadily expanded. In July 1966, work was completed that allowed the concentrator to treat in excess of 18,000 tpd. Almost immediately Pima embarked on another expansion program that will increase plant capacity to 30,000 tpd during the summer of 1967. This repeated expansion has corresponded with the development of additional low-grade ore deposits and with the improved operating economics realized by handling larger masses of material. Early in the life of Pima it was known that a mineralized area was present on the flanks of the high-grade orebody which systematic drilling had shown to be a low-grade copper orebody. Many months of engineering studies revealed that this was sufficient to allow Pima to compete with other large scale, low-grade copper operations in the Southwest.

Jan 11, 1967

By Kenneth Cottingham

THE area described herein is situated on what is known as the Arches Fork anticline in Roane and Calhoun Counties, W. Va. When the area was first mapped, it was felt that well records would give a more intimate idea of conditions, both structural and lithologic, than could be expected from surface horizons. The surface formations are chiefly members of the Monongahela series, though northward the hilltop outcrops are those of the Dunkard. Neither series offers a key horizon sufficiently definite to be satisfactory, although the structure as determined from well records was later checked against two of the more persistent surface sandstones. In mapping the subsurface structure, the top of the Big Lime (Greenbrier) was employed as the key horizon. The average depth to the top of the Big Lime varies from 1600 to 2000 ft. (487 to 609 m.), while the average thickness as indicated by well records is 113 ft. (34 m.). The oil-producing formation is the Big Injun, lying just below the Big Lime. In two instances, well records show the Lime and Injun separated by a few feet of "break." The Big Injun is recorded as having a variable thickness. Seven logs report it as missing and one gives it the maximum thickness of 105 ft. (32 m.), while the entire average for thickness is 19 ft. (6 m.).

Jan 1, 1922

By Louis D. Huntoon

CANADIAN gold production is forging ahead annually and the prospects are that it will continue to do so for many years. Table 1 shows recent annual increases. Production for 1933 will probably reach $70,000,000, and further increases are likely in 1934 and 1935. (Data for November and December, 1932, are estimated throughout this article.) The depression sent many prospectors to the woods so during the last two years many new gold areas have been discovered and are attracting real capital for exploration and development. Several mills came into production in 1932 and mills now under construction will start production in 1933. The offices of mining lawyers are busy. Capital for this new work is obtained from well financed mining companies, syndicates, and individuals who were fortunate enough to invest in the dividend-paying gold mines of the north country in the early days. Prospectors and capital are cooperating. An interest is always retained by the prospector or vender and usually a small amount of real money is given the prospector.

Jan 1, 1933