Search Documents

By H. T. Clark

NO previous determinations of the deformation or recrystallization textures of titanium or of titanium-base alloys have been reported in the literature. The room-temperature structure of titanium is hexagonal close-packed with a c/a ratio less than 1.633. It would be expected, therefore, to have a rolling texture similar to that of other hexagonal close-packed metals, namely (0001) [1010]. Burgers and Jacobs1 have shown that zirconium, a metal isomorphous with titanium in its structure and similar in many of its properties, has such a texture with a scatter of the basal plane toward the transverse direction. This scatter is in the opposite direction from that found in magnesium by Bakarian2 but similar to that reported by Smigelskas and Barrett3 or beryllium. The rolling and annealing textures reported here for high-purity iodide titanium are significantly different from the . textures of any other hexagonal close-packed metal. All titanium used during this investigation was prepared by the iodode process." The annealed hardness of this material varied from 73 (material used for sample No. 2) to 97 Vickers hardness number. An estimate of the chemical composition of this grade of titanium has been reported by Finlay and Snyder.5 With one exception, shown in table I, the as-deposited titanium was cast into 10 to 20 g ingots in an electric arc furnace in purified argon before being rolled to sheet. The cast ingots were forged and ground until their cross-section was approximately rectangular, annealed 1 hr at 700°C in vacuum and cold rolled. Rolling was carried out in a two-high, 4 in. diam mill, using reductions no greater than 10 pct per pass. The direction of rolling was reversed after each pass, and, in order to avoid temperature effects, the sheet was allowed to cool after each pass. Unless the rolled sheet was sufficiently thin for X-ray penetration (about 0.004 in.), it was reduced to this thickness by pickling. Because of the possibility of introducing twinning or other deformation during grinding, no attempt was made to maintain uniform thickness of the sample during pickling by intermediate grinding or sanding operations. Those samples to be used for determining the annealed texture were recrystallized by vacuum annealing the cold-rolled sheet for 1 hr at 500°C. These thin samples were held between thick titanium sheets during annealing to prevent distortion. Table I outlines the rolling and annealing schedule of those samples for which photograms or texture patterns are shown. X-ray Techniques The usual techniques for determining textures were employed during this work. Molybdenum radiation was used for the transmission exposures and copper radiation for the glancing angle ones. Since titanium fluoresces under these conditions, it is necessary to employ a filter between the sample and the film. The Kß radiation filters are very satisfactory for this purpose. Sufficient grains having favorable orientation were present in both the cold-worked and in the cold-worked—500°C annealed samples to provide satisfactory patterns with the samples stationary. Because of the difficulties of comparing intensities of transmission photograms with those obtained

Jan 1, 1951

Following closely Marcona Corp.'s announcement of its new Marconaflo process for transporting mineral slurries by ship (see pp. 96-97, Sept. 1969 [ ]), Midland-Ross Corp. (M-R) now heralds its metallized iron pellet process which supplements Oregon Steel Mills1 (Oregon Steel) new Portland, Ore., plant. Harry J. Bolwell, president of M-R describes the company's M-R Pellet as "the most exciting advance in steelmaking in a decade, one which will profoundly affect the industry." In fact, other knowledgeable industry spokesmen believe that with these developments the mini-steel plant era is now here and that this technical development along with the Marconaflo process will revolutionize iron ore shipments and steelmaking. The M-R president predicts that electric furnaces can account for 20% of the annual U.S. steel production by 1975, compared with 14% at the present time because of these developments.

Jan 12, 1969

By S. B. Casey

[ ] IN 1880, an electric arc was struck over metal for the first time to experiment with controllable melting. The glare of this arc has reflected on the stacks of the steel industry and continued to light the path of steelmakers in their never ending quest -for faster, more economical, and better ways of producing steel. William Siemens is credited with first employing the electric arc to melt metal in a closed hearth and produce basic metallurgical reactions. By the turn of the century, an Italian, named Stassano, was experimenting with ore reduction by the electric arc. In 1899, Dr. Paul Heroult, in France, used the direct arc principle for producing ferro-chromium. His experiments quickly led him to develop a dosed-top arc furnace for the production of steel, and his first commercial shipment was recorded in December, 1900. American steelmakers, quick to sense the possibilities of this method of melting, invited Heroult to our shores, where, in 1905, he was responsible for installing the first arc furnace on the North American continent. This furnace, at Sault Ste. Marie, was built for ore reduction. But Charles Holcomb, founder of Holcomb Steel. Co. of Syracuse, N. Y. contacted Heroult in 1905 and contracted for the first American direct-arc electric furnace for steelmaking. On April 5, 1906, the first heat was tapped from this 3-ton unit. The furnace was basic lined and powered by a single-phase, 500 kw generator, -producing high amperage at low voltage. It is interesting to note that, although the first few heats were made with cold charges, subsequent heats were duplexed. R. H. Bully, first superintendent of Holcomb Steel, persuaded the directors to purchase the unit to effect a more economical and efficient means of making tool steel by duplexing prime melting in a combustion fired furnace, and transfer of hot metal to the arc furnace for temperature adjusting, refining, and adding carbon and alloying elements. Today, duplexing is foreseen by some as the steelmaking process of the future. The promise shown by America's first arc furnace for ingot production quickly led to the purchase of a similar unit by The Firth Sterling Steel Co., in 1909, and to the purchase of the first arc furnace for production of steel castings, by the Treadwell Engineering Co., in 1911. From its humble start in 1906, production of arc furnace steel has never ceased to increase its yearly percentage of total steel production in the U. S., although certain other methods have declined or almost disappeared. By its ability to be used intermittently, the arc furnace gained favor and enhanced its reputation during depression days. When the attack on Pearl Harbor plunged us headlong into the long days of World War II, the arc furnace stood ready, flexible enough to be overburdened hearth wise 30 pct and power wise 25 pct, pouring its endless flood of alloy for the guns, tanks, ships, and planes which ultimately brought victory. During the post war boom, the now, proven virtues of low initial cost, faster installation, better yield, improved availability, and lower operating cost, enabled industry-particularly the small, new, independent producers-to locate strategically and profitably to meet the demand of an America that had been starved for new homes, appliances, cars, and highways. In the Korean police action, the arc furnace again proved itself by providing the latest alloys metallurgists could develop to meet the demands that the jet age and the innovations of guided missiles required. In today's peacetime prosperity, the arc furnace is continuing to provide the economic flexibility required to meet an ever increasing demand for better steel in the face of mounting costs, scrap shortages, and pressure toward decentralized location of industry.

Jan 1, 1961

By J. T. Norton, N. J. Grant, A. M. Gervais

An investigation of the creep deformation of coarse-grained high-purity aluminum at temperatures approaching the melting point permitted the formulation of a theory of subgrain formation. Subgrain boundaries were found to be formed by two different processes: kinking and polygonization. Polygonization is considered as the main factor in subgrain formation. SINCE "slipless flow" was first discussed in detail by Hanson and Wheeler,' many studies have been undertaken to determine how metals deform at high temperatures. Several types of observations have been reported. Jenkins and Mellor,² working on the creep of mild steels and various grades of commercial irons, found metallographic evidence of a kind of substructure within the grains after deformation at high temperatures. Homes" observed after creep deformation of steel at high temperatures that the original X-ray spots were sharply divided into several small ones. The same phenomenon was reported by Hirst4 from his studies on lead and later by Crussard5 from his work on aluminum. The works of these investigators demonstrated beyond any doubt that the splitting of the X-ray spots was due to the fact that the grains underwent a division into subgrains during deformation at high temperatures. Since then, numerous experiments have been undertaken on aluminum in order to determine the mechanism of formation of subgrains. Research workers can be divided, for the purpose of discussion, into two different groups as regards thinking on subgrain formation. On one hand, based on the work on polygonization by Cahn,6 Guinier and Lacombe,7 Greenough and Smith," Crussard,10,11 and Servi, Norton, and Grant," it was concluded that subgrain formation was a consequence of the simultaneous effects, first, of inhomogeneous deformation which produced bending of the lattice, and second, polygonization. On the other hand, Wood and coworkers13-16 based their work on the results of an earlier report" which dealt with crystallite size and a fragmentation theory. It is interesting to note that while Greenough and Smith8 and Wood et al. performed similar experiments, their conclusions were quite different. Wood et al. did not recognize polygonization as a fundamental mechanism and said that aluminum, at the beginning of the deformation, fragmented immedi- ately into subgrains in order to permit deformation of the metal, the number of these subgrains being a function of strain rate and temperature. They concluded that deformation of grains occurred by flow along the subgrain boundaries. In view of the contradictory conclusions, it would appear that the data were not explicit enough to provide an unambiguous conclusion. It appears that the techniques by which most of the results were obtained, namely, X-ray work, were not enough by themselves to solve the problem. Another approach was needed. In the present research, therefore, an extensive metallographic study was planned to supplement the X-ray work. The importance of revealing the subgrain boundaries metallographically was realized, and this will explain the extensive development and use of etching techniques. In order that subgrains would be considerably larger and therefore more readily visible under a microscope, the creep experiments were performed at very high temperatures approaching the melting point of aluminum. Development of Experimental Technique Creep tests were run at constant load on high purity (99.995 pct) aluminum specimens having a very coarse grain size. None of the specimens was run to fracture. The specimens were originally round (diameter, 0.187 in.; gage length, 1 in.) and had parallel flats milled in the gage section to permit

Jan 1, 1954

By P. E. Senseny

INTRODUCTION Massive hydraulic fractures have been used since 1949 in the petroleum industry to enhance production rates and increase recoverable reserves. Currently, a research program, the Multi-Well Experiment, is underway to develop the understanding and technology to a1 low economic production of the large gas reserves of the low permeability, lenticular sandstone formations in the western U.S. (Atkinson, et al, 1981; Northrop and Sattler, 1983). Use of state- of-the-art hydraulic fracturing techniques is a part of this investigation. As a portion of an extensive core program in support of this experiment (Sattler, 1983), fracture toughness has been determined for 56 sandstone, shale, mudstone, or siltstone horizons from three wells in the Piceance Basin. The role of fracture toughness in hydraulic fracturing is not well understood because other factors, such as in situ stress, dominate fracture geometry and containment. Rubin (1983) concluded from analysis of his laboratory hydrofracture experiments that fracture toughness should be included in design and numerical simulation of hydraulic fractures. However, van Eekelen (1982) contends that the stress intensity at the crack front should be so much greater than the fracture toughness of the rock that toughness can have no importance. Generally, fracture toughness and other material properties, such as elastic moduli and permeability, are thought to be of secondary importance in determining fracture geometry and containment. In spite of this, there is a need to acquire a more quantitative understanding of their importance for accurate design and simulation calculations. Analysis of fracture geometry and containment data from hydraulic fracturing experiments carried out in formations where fracture toughness and other rock properties are

Jan 1, 1984

By G. Sachs

X-RAY analysis and single-crystal study have been utilized in recent years as a new means of following constitutional changes in alloys. If such transformations can be suppressed by rapid cooling, they can be followed at room temperature in a particularly convenient manner. In the following we shall consider changes in solubility and polymorphic transformations with particular reference to phenomena of the age-hardening type. Finally a thermodynamic viewpoint is developed for examining such transformations.

Jan 1, 1931

By A. L. Field

Previous Publications THE first report on the slag viscosity work of the Bureau of Mines was made by one of the authors 1 in 1916. It was concerned chiefly with, the method of measurement. A paper 2 on this phase of the work was presented to the Institute in February, 1917, and a similar paper 3 was communicated to the Faraday Society. Purpose and Scope of the Slag Viscosity Tables Following the development of a suitable method, the next step in the investigation was the measurement of slag viscosity over a wide range of temperature and composition, and the arrangement of this experimental data in the form of tables for the use of the blast-furnace operator. It is believed that this information, if used intelligently, should help the operator to reduce losses in production caused by off-grade pig iron, to improve fuel economy, to promote operating efficiency, and to extend present-day practice to meet the increasing need of smelting lean and complex ores. In the experimental part of the work it was early observed that the temperature-viscosity relations of a slag were determined, for practical purposes, by the relative proportions of the three major constituents, lime (CaO), alumina (Al203), and silica (Si02), provided the percentage

Jan 12, 1917

By Walter Renton Ingalls

Metallurgical literature has no record of any ore beneficiated for cadmium alone, and the cadmium of commerce is derived from zinc ore, with which cadmium is generally associated. Zinc ores free from cadmium—e.g., the ores of the Franklin and Stirling mines, New Jersey, and of Broken Hill in Rhodesia—are rare. Blende concentrates of 50 to 60 per cent grade have contained (in production of important tonnage) as much as I per cent Cd, which is unusually high. The concentrates from the Tri-State district average from 0.3 to 0.4 per cent Cd, which is high. The concentrates from mines west of the Rocky Mountains seldom are higher than 0.2 per cent. In the periodic system of the elements, cadmium is in the same group with zinc. Its properties and compounds are similar. Its metallurgy is also similar. Cadmium has a melting point of 320°C. and a boiling point of 778"C., while the melting point of zinc is 415'C. and the boiling point gos°C. These conditions, together with the lower reduction temperature of cadmium oxide, indicate means for. separating cadmium from zinc. Cadmium in spelter is viewed, if not as an impurity, at least as an alloying element that may be objectionable, its special effect being hardening. However, for some purposes, a little cadmium in spelter is desired, and 0.4 per cent may be permissible, even in spelter for rolling. Cadmium in spelter for brassmaking is completely volatilized at the temperature of that process, and in bygone days an immense quantity of cadmium must have been lost in the fumes from these furnaces. Pyrometalltjrgy—Early Cadmium compounds, sulphide and oxide, being more volatile than the corresponding compounds of zinc, loss of cadmium begins to occur from the first furnace operation. In normal roasting, even with Tri-State ore, this loss may not be very high. Raw ore, assaying 0.4 per cent Cd, may be expected to give a roasted product of the same assay, which would imply a cadmium loss of about 15 per cent. Roasted ore, assaying 0.4 per cent Cd when distilled at ordinary furnace temperature, yielded spelter containing about half of that in the ore charged. The first draw of spelter under these conditions may assay 0.8 per cent Cd (accounting for 22 per cent of the cadmium recovery) and after the several draws of spelter have been equalized the cadmium content may average 0.35 per cent. If, therefore, 2000 lb. of blende averaging 0.35 to 0.4 per cent Cd is roasted and distilled, there may be obtained 1000 lb. of spelter, assaying 0.35 per cent Cd or 3.5 lb. content, which entering into Prime Western spelter will be sold at the spelter price. It will be observed from the outline hereinbefore (summarizing conditions prior to the introduction of sintering) that the main loss of cadmium occurred in the distillation process and by failure to condense, which could be ameliorated by attaching a prolong to the condenser, thus collecting

Jan 1, 1944

By John L. Watson

A conceptual model (MAGSEP) is described to simulate the beneficiation characteristics of a drum magnetic separator in terms of the probability of an individual grain being recovered in the magnetic concentrate. This probability is determined as a function of particle magnetic composition and magnetic field strength and is modified by particle size and the separator operating conditions. The model predicts the size, magnetic grade and distributions of magnetic and gangue minerals in the concentrate and tailings produced by the drum separator. The configuration of the magnetic concentration circuit may be altered to permit single or double drum units in parallel or series operation. The characteristics of the feed material, in terms of a magnetic parameter, are essential in permitting the determination of individual grain recovery probabilities upon which the model is based. Thus the model requires input data relating to the distribution of composite grains in terms of magnetic grade and particle size. To illustrate the use of the conceptual model an example is given for the beneficiation of New Zealand iron sands.

Jan 1, 1984

By J. W. Freeman, D. N. Frey

Fundamental reasons for the improvement in creep resistance of an austenitic alloy by cold working were investigated mainly by X-ray diffraction. The creep resistance was found to be improved by the internal stresses in the lattice of the alloy induced by the cold work. THIS investigation was concerned with the fundamental reasons for improvement in creep resistance of an austenitic alloy as a result of cold working. Also, the investigation was carried out to elucidate the conditions under which cold working could be expected to improve the creep resistance. To achieve these ends, creep resistance and internal structure were correlated for a variety of cold-worked conditions. Since the aim of the investigation was not to obtain specific and extensive information on any one alloy, creep testing was done with a single stress at 1200°F. Structural studies were carried out primarily with X-ray diffraction characteristics. The alloy used, low carbon N-155, was selected on the basis of being representative of at least some of the alloys used in gas turbines. Low carbon N-155 alloy in the form of %-in. sq bar stock was used in this investigation. The chemical composition, in percent, was: C, 0.13; Mn, 1.43; Si, 0.34; Cr, 20.73; Ni, 18.92; Co, 19.65; Mo, 3.05; W, 1.98; Cb, 0.98; N, 0.14; and Fe, balance. The bar stock was produced from a 13-in. sq billet, finished to 7/s in. round cornered square between 2060" and 1910°F. Prior to use in this particular investigation, the bar stock was solution-treated 1 hr at 2200°F and water quenched. This procedure was used in order to put the stock in a condition where effects of prior processing were minimized. Experimental Procedure The specific approach to the problem was twofold. First, the influence of cold working, under various conditions, on the creep rate under a single stress at 1200°F and on the internal structure was in part determined. Second, the effect of annealing at various times and temperatures on the creep rate and internal structure of the cold-worked samples was in part evaluated. The first step was basic to the investigation—creep resistance and structure were to be correlated. The second step was taken to see if the annealed samples showed some internal changes which could also be correlated with changes in creep resistance. This it was felt would facilitate solution of the basic problem. The creep and structural studies were carried out on samples reduced approximately 5, 15, and 40 pct at room temperature and 15 pct at temperatures up to 2200 °F. Annealing of various of the samples was done at 1200°, 1400°, 1600°, and 1800°F for time periods up to 1000 hr. Studies of the annealed samples were concentrated on materials rolled approximately 5, 15, and 40 pct at room temperature and 15 pct at 1400°F. The creep tests were carried out at 1200°F under 40,000 psi, the latter being approximately the 1000 hr rupture stress of the material

Jan 1, 1952

By D. H. Polonis, M. B. Kasen

AN unusual thermal etching phenomenon has been observed on the surface of a Cu-Si alloy. The observations were made during studies of vacancy condensation pit formation which were reported in previous papers.1,2 Figs. 1 and 2 are photomicrographs of the surface of a Cu-4.8 pct Si alloy after heating in vacuo (3 x X mm Hg) to 525°C and subsequently holding at that temperature for 16 hr in an impure (air-contaminated) argon atmosphere. Under these conditions preferential removal of silicon from the matrix by oxidation results in a surface which is entirely a phase overlying an a plus y structure. The light areas of Fig. 1 are regions in which very little thermal etching has occurred, while the majority of the surface has experienced severe etching. Similar regions in Fig. 2 are seen as plateaus above contours produced by net transfer of material from the specimen surface. Twin boundaries are also visible in Fig. 2. The difference in matrix mi-crostructure between Figs. l and 2 reflects the par- ticular orientation of low-index planes with respect to the surface of observation. Thermal etching contours of this type have been studied in detail by Hondros and Moore Both of the photomicrographs show that one or more dark spots are located approximately at the center of every protected area; where two spots are in close proximity, the protected areas have merged. The microstructures indicate that the anomalous resistance to thermal etching is related to the presence of these spots. Williams and Hayfield have shown that local regions of unusually high oxidation resistance can be caused by a surface monolayer of atoms with a work function higher than that of the base material. The result is an inhibition of the rate of electron removal from the base material and a decrease in the oxidation rate. The source of the protected layer may be either surface diffusion from contaminants on the specimen surface or pipe diffusion of solute atoms followed by migration across the surface. In the latter case the driving force is a difference in chemical potential resulting in a Gibbs adsorption phenomenon. In the present case, chemical polishing of the specimen surface precluded contaminants of a strictly surface nature. Consequently, diffusion of impurity atoms from within the lattice appears to be the most tenable explanation of the observed phenomena. The authors propose that the structures of Figs. 1 and 2 reflect the diffusion of impurity atoms along extended dislocations within the individual a phase grains prior to surface oxidation. The central spots within the protected regions are seen as sites of dislocation emergence which have become locally decorated with oxide in the manner discussed in Ref. 1. Williams and Hayfield observed protected regions adjacent to the grain boundaries of iron-contaminated copper which they attributed to the segregation of iron to the grain boundaries coupled with high dif-fusivity along the complex dislocation array at such boundaries. No evidence of such grain boundary protection was observed in the Cu-Si alloy; this

Jan 1, 1964

By Roger B. Alke

INTRODUCTION Request to Mine Beneath Bridge The Jakes Run Bridge is a reinforced Portland concrete arch filled bridge located on WV Route 7 near Pentress, WV. The bridge has a span of 22.9 m (meters) and a height of 4 m above normal pool elevation to the underside of the center of the arch (See Fig 1). The bridge is a two lane structure with a width of 6.86 m. The structure is over 50 years old having been built in 1929 and is owned by the Department (WV Department of Highways). [ ]

Jan 1, 1984

IRON AND STEEL DIVISION Established as a Division February 22, 1928 K C. McCutcheon, Chairman T. L. Joseph, Past Chairman J B Austin, Vice-Chairman E K Miller, Vice-Chairman T. J. McLoughlm, Vice-Chairman Ernest Kirkendall, Secretary-Treasurer CO M M I T T E E S EXECUTIVE J. A. Bowers '54 J. S. Marsh '55 R. W. Campbell '54 D. L. McBride '53 Walter Carroll '55 G. B. McMeans '53 K. L Fetters '53 F. L. Toy '54 H. M. Griffith '55

Jan 1, 1952

By J. Brett, L. Seigle, L. Castleman, T. Montelbano

Impurity-induced low-temperature recrystallization of cold-worked tungsten was inuestigated with emphasis on the influence of nickel on the reaction. Palladium, nickel, aluminum, manganese, platinum, and iron greatly lower the recrystallization temperature of doped tungsten, which zs normally very high, but the recrystallization temperature of electron-be am zone-refined tungsten wzre is slightly raised by conlacl with nickel. Recrystallization can be induced at low temperature by the presence of solid nickel on the surface of doped tungsten wire, but apparently not by exposure to nickel vapors alone. Approximately 200 ppm of Ni dijjused into 10-mil wires at 1200 from a deposit of nickel on the surface produced total recrystallization, whereas more than 600 ppm of Ni could be absorbed frotn a vapor source without altering the fibrous structure of cold-worked tungsten. Once initiated, nickel-induced recrystallization required a continued source of' nickel for propagation of the recrystallization front. The solubility of nickel in fibrous 10-mil W wire was approximalely 500 ppm at 1150' C, and the activation energy for penetration of the recrystallization front was 52 kcal per mole. In many applications the usefulness of tungsten depends on critical control of its structure. Cold-worked tungsten with the fibrous structure developed by suitable thermo-mechanical treatment has a low, but technologically significant, ductility. It has long been known1 that traces of nickel, and perhaps other metals, are profoundly deleterious in doped tungsten, because they induce recrystallization at low temperature, which produces a brittle, equiaxed grain structure. This effect appears to be an exception to the general observation that recrystallization is impeded and the recrystallization temperature raised by the presence of impurities.2"9 Previous studies7-'' of the annealing and recrystallization of tungsten wire have divided the phenomenon into prior recovery stages, primary recrystallization and secondary recrystallization. The present investigation is concerned principally with primary recrystallization which is defined here as the replacement of the fibrous structure of deformed tungsten by equiaxed grains. The objective of this study was to explore the nickel-induced recrystallization reaction in tungsten and attempt to elucidate its mechanism. As well, an effort to define which other elements give rise to low-temperature-induced recrystallization was carried out. EXPERIMENTAL PROCEDURE The procedure adopted for these experiments was essentially to bring nickel and other elements into diffusive contact with cold-worked tungsten wires. The process of recrystallization was followed as a function of time and temperature by light and electron microscopic observations. First the influence of nickel on the recrystallization temperature of arc-melted, zone-refined, and variously doped tungsten wire was determined by electroplating a deposit of nickel on the surface of the wire and annealing at a variety of temperatures for 3 hr. The chemical analyses of the tungsten wires used in this investigation are given in Table I. The surface of the tungsten wire was etched with Murakami's slution' and approximately 0.005 in, of Ni was deposited from a Watts-type low pH bath14 for the conditions of these experiments. Variations in plating thickness from about 0.001 to 0.005 in. had no discernible influence on the resulting structures. The wires were then annealed in an atmosphere of dry hydrogen to establish the recrystallization temperature. Concurrently, un-plated specimens were annealed to establish the recrystallization characteristics of nickel-free wire. The criterion of recrystallization was that the fibrous structure be completely replaced by equiaxed grains after a 3-hr treatment of temperature. This provided more reproducible results than use of the first recrystallized grain or a fixed proportion of re-crystallized structure as the critical observation. The structures encountered in longitudinal and transverse sections were examined by both light and electron microscopy at magnifications up to X32,000 using parlo-dion-carbon replicas shadowed with platinum for the latter method. Second, the influence of a variety of metals on the recrystallization temperature of 0.010 in. D alumina-silica doped tungsten wire, AW136-64, was determined. The elements were applied by electroplating whenever possible. Alternatively, they were vapor-plated on the tungsten wire and a greater thickness built up by coating with a dispersion of metal powder in nitrocellulose lacquer. Elements not amenable to either of these procedures were merely slurry coated on the tungsten. The recrystallization temperature was determined as above. Third, the nickel-induced recrystallization process in doped wire was studied more closely by electroplating 8 mils of Ni on 65-mil alumina-silica doped tungsten wire, AW153-NS10, and exposing the wire to temperatures of llOO°, 1200°, or 1300°C for various times in a hydrogen atmosphere. A circular recrystallization front, 'Onsisting of equiaxed grains, developed at the periphery Of the coated tungsten wire, and the advance of this front into the fibrous interior was studied. These experiments employed relatively coarse 0.065 in. D wire because the 0.010 in. D wire recrystallized too quickly to permit observation of the pene-

Jan 1, 1969

(Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members.) Members and guests who called at Institute headquarters during the period July 10, 1916 to August 1, 1916: W. A. Barnes, San Francisco, Cal. W. J. Mead, Madison, Wis. W. L. Bell, Davenport, Fla. Charles Mentzel, San Pedro, N. M. James P. Clarke, Jr., Little Rock, Ark. H. H. Miller, New York, N. Y. R. A. Carhart, Mitchell, S. D. W. E. Pomeroy, El Paso, Tex. G. M. Colvocoresses, Humboldt, Ariz. M. K. Rodgers, Los Angeles, Cal W. E. Defty, Phoenix, Ariz. S. C. Rodgers, Guanajuato, Mex. Carl F. Dietz, Worcester, Mass. John M. Baker and Hamilton W. Baker have resigned as general manager and mine superintendent respectively of the Baker Mines Co., of Oregon. After Aug. 1, their address will be 43 Emerson St., Denver, Colo.

Jan 9, 1916

By E. C. Pechin

AT the suggestion of some members of the Institute, attention is called to the record of the working of Dunbar Furnace during the twelve months ending in January, 1874. During this period, with a product of over eleven thousand gross tons, not a single ton of

Jan 1, 1874

By L. Kaufman

An equation is derived relating AF a", the difference in free energy between austenite and martensite, to temperature and composition in the iron-chrmnium and iron-chromium -nickel systems. This equation is used to calculate at M,for low-carbon stainless steels. A method for utilizing the energetic equations to calculate M, in stainless steels is suggested. In addition, an explanation is given for the anomalous effect of chromium in forming a y loop concurrent with the lowering of M, in iron-base alloys. It has been demonstrated that the effect of alloying elements on the Ms temperature is strongly dependent upon the influence of the alloying element on the thermodynamic properties of the y and a phases. Notwithstanding the fact that alloying elements affect the Ms temperature by changing the lattice parameters, elastic constants, and inter-facial energies of the a and y phases, their primary role is a thermodynamic one. Thermodynamic analyses have been presented for the iron-carbon'-4 and iron-nickele systems in which equations are derived for Fa and FY, the free energies of the b.c.c. (or b.c.t.) and f.c.c. phases. These equations, which can be obtained with the aid of the equilibrium diagrams, can be used to help predict the Ms vs composition curves. This paper deals with a calculation of the thermodynamic properties necessary to compute AFffLY for iron-chromium alloys. In view of the lack of direct information concerning the activity of chromium in the a and y phases of iron, the regular solution approximationa,g was utilized to bridge the gap. After the necessary equations were derived for the iron-chromium system they were used to calculate AFff— Y for stainless steels by combining them with the previous results obtained for iron-nickel alloys. The results of these calculations offer a means of rationalizing the anomalous behavior of chromium in iron-base alloys. The latter depends on the regular solution approximation in contrast to the explanation offered by zener , which is based upon the "magnetic specific heat effect." THERMODYNAMICS OF THE IRON-CHROMIUM SYSTEM If y represents the atomic fraction of chromium in an iron-chromium alloy, then the free energy of the b.c.c. phase Fa, the f.c.c. phase FY, and the difference in free energy between the f.c.c. and b.c.c. phases of the same composition are given through [3] and Fmy represent the free energies of mixing of the a and y phases; while @era -' and uFea 4Y represent the difference in free energy between f.c.c. and b.c.c. chromium and iron respectively. The values of AEFe0ff4Y in the temperature range between 0" and 900K ( .

Jan 1, 1960

By Basil B. Zavoico

During 1938 the Russian oil industry, while able to increase its production 4.69 per cent above the preceding year, was not successful in correcting some of its basic difficulties, and the industry's position as it entered 1939 was unsatisfactory. The internal political difficulties of 1937 and 1938 took a toll in the oil industry as they did elsewhere in the U. S. S. R., further complicating the solution of the problems facing it, most important of which still remain: lack of experienced and responsible leadership, able to make quick decisions; undisciplined and migratory labor; and insufficient and often unsatisfactory quality of the various equipment needed by the industry and its ineffective distribution. Recent developments in the U. S. S. R. suggest that during 1939 the management will be granted more latitude and hence somewhat better results may be anticipated from the executive branch, provided, however, the "purges" do not recur. The labor should be better disciplined and should not shift as easily, owing to the introduction, at the close of 1938, of individual labor passports to all workers in the country, the principal purpose of which is to correct those two deficiencies. It is not anticipated, however, that the service of supply will show any appreciable improvement in 1939, partly because of inherent difficulties and partly because the manufacturers of heavy machinery are working primarily and necessarily for munitions. Production Production of crude oil during 1938 is estimated at 224,714,000 bbl., as compared with 212,742,000 bbl. in 1937, an increase of 4.69 per cent but 12.76 per cent below the planned output. While there were no major readjustments in the source of supply of crude oil, both the older districts, Baku and Grozny, were barely able to maintain their 1937 levels of production, the increased output being supplied primarily by the fields of Maikop and Ural Permian Basin districts. While exploration work was outstandingly successful in 1937, in 1938 no discoveries of any

Jan 1, 1939

By Basil B. Zavoico

During 1938 the Russian oil industry, while able to increase its production 4.69 per cent above the preceding year, was not successful in correcting some of its basic difficulties, and the industry's position as it entered 1939 was unsatisfactory. The internal political difficulties of 1937 and 1938 took a toll in the oil industry as they did elsewhere in the U. S. S. R., further complicating the solution of the problems facing it, most important of which still remain: lack of experienced and responsible leadership, able to make quick decisions; undisciplined and migratory labor; and insufficient and often unsatisfactory quality of the various equipment needed by the industry and its ineffective distribution. Recent developments in the U. S. S. R. suggest that during 1939 the management will be granted more latitude and hence somewhat better results may be anticipated from the executive branch, provided, however, the "purges" do not recur. The labor should be better disciplined and should not shift as easily, owing to the introduction, at the close of 1938, of individual labor passports to all workers in the country, the principal purpose of which is to correct those two deficiencies. It is not anticipated, however, that the service of supply will show any appreciable improvement in 1939, partly because of inherent difficulties and partly because the manufacturers of heavy machinery are working primarily and necessarily for munitions. Production Production of crude oil during 1938 is estimated at 224,714,000 bbl., as compared with 212,742,000 bbl. in 1937, an increase of 4.69 per cent but 12.76 per cent below the planned output. While there were no major readjustments in the source of supply of crude oil, both the older districts, Baku and Grozny, were barely able to maintain their 1937 levels of production, the increased output being supplied primarily by the fields of Maikop and Ural Permian Basin districts. While exploration work was outstandingly successful in 1937, in 1938 no discoveries of any

Jan 1, 1939

By John Wellington Finch

WHAT is an engineering opportunity? To the mining .engineer the natural assumption is that the first requisite 'is a mineral deposit, but, of course, it is not so simple as that. There are at various points on the earth really very great mineral deposits which, on account of geographic location, backwardness of the country, or hostility of its natives, are now, and for a long time to come will be, quite valueless. The mining engineer, and for that matter the civil engineer, is more dependent upon the decisions of capital than upon any other factor in his profession. Ordinarily it is to be assumed that money will go to any place where it is clear that an adequate return upon its investment can be secured, but for many years it has not been safe to depend upon this. ' As already stated, there are many places where local conditions are such that mining is not safe to engage in and there are still other places in which conditions have been so aggravated by the Great War and by the social unrest which has upset the Asiatic region that capital is naturally most reluctant to venture, even when engineering data makes the undertaking appear attractive. It will be evident, I. believe, that there are many factors vital to the success of a mining enterprise in some of the remote countries which we do not have to consider in the United States and which do not, in fact, exist here.

Jan 1, 1924