Search Documents

By C. E. Armantrout, J. A. Rowland, D. F. Walsh

THE close-packed-hexagonal structure of mag-J- nesium is converted to a ductile and malleable body-centered-cubic lattice by the addition of lithium in excess of 10 pct. Further, the density of magnesium or magnesium-base alloys is decreased by additions of lithium. The practical possibilities of such alloys as a basis for uniquely light, malleable, and ductile structural materials were pointed out by Dean in 1944' and by Hume-Rothery in 1945.2 It was apparent to these investigators, however, that more complex compositions would be required if strengths sufficient for structural applications were to be developed in these alloys. In a search for strengthening additions, various investigators w have examined a number of the ternary and more complex alloys containing magnesium and lithium. An investigation of the fundamental characteristics of these alloys was undertaken by the Bureau of Mines. The investigation was initiated with a study of the magnesium-rich corner of the equilibrium diagram for the ternary system, Mg-Li-Al. The following data from published investigations of Mg-Li-A1 alloys were available: 1—a description of isothermal sections at 20" and 400°C through the Mg-Li-A1 constitution diagram by F. I. Shamrai;' 2—a diagram by P. D. Frost et al." showing approximate phase relationships at 700°F for a number of the Mg-Li-A1 alloys; and 3—diagrams showing the constitution at 500" and 700°F for the Mg-Li-A1 alloy system published by A. Jones et al.' Where compositions and temperatures permit comparison, these diagrams show disagreement. The 700°F isotherms of Frost and Jones differ only in the placement of the phase boundaries. But Sham-rai's 400°C (752°F) isotherm shows a variation in phases as well as in phase boundaries. Although rigid comparison of these different isothermal sections might not be justifiable, it seems impossible to reconcile Shamrai's construction with the isotherms of Frost or Jones. The isothermal sections presented in this paper were prepared to determine compositions which might be suitable for age hardening and to develop the general slope and placement of the various phase boundaries in the magnesium-rich corner of the diagram. Sections at 375", 200°, and 100°C were selected for investigation. In constructing these sections, the solubility of aluminum in magnesium, as reported by W. L. Fink and L. A. Willey Vn 1948, was used at the binary Mg-A1 boundary and the solubility of lithium in magnesium was obtained from the equilibrium diagram for that system as reported by G. F. Sager and B. J. Nelson" in the same year. The solubility of magnesium in lithium was determined experimentally and conforms in general to data reported by P. Saldau and F. Shamrai." Parameters for AlLi and MgI7A1, were taken from American Society for Testing Materials X-ray diffraction data cards. Experimental Procedures Although the isothermal sections presented in this paper are not unusually complex, the experimental techniques involved in their construction are made extremely difficult by the relatively high vapor pressure of lithium and the great chemical activity of both magnesium and lithium. Because of these characteristics, which make precise control of the composition of equilibrium-treated filings practically impossible, the disappearing phase method was used in preference to the parametric method in conjunction with metallographic studies. The alloys used in this investigation were melted and cast in an atmosphere of helium using a tilting-type furnace which enclosed a steel crucible and mold in a single unit. Each portion of the charge (500 to 600 g) was cleaned carefully just before placing it in the crucible; and the charge, crucible, and entire melting apparatus were evacuated and then washed with grade A helium while preheating to approximately 100°C. The alloys were melted and chill cast in an atmosphere of helium. Alloys prepared in this way were relatively free from inclusions and a fluxing treatment was considered unnecessary. The cylindrical ingots obtained were scalped and then reduced 96 pct in area by direct extrusion, yielding % in. diam rod. Sections of the rod, approximately 3 in. long, were given equilibrium heat treatments and then sampled for metallographic examination, X-ray diffraction study, and chemical analysis. The surface of each equilibrium-treated rod was machined to a depth sufficient to insure removal of contaminated material before samples for chemical analysis or X-ray diffraction study were obtained, and all decisions on microstructure were based on the examination of the central portion of the metallographic specimen. All specimens homogenized at 375°C were analyzed after this equilibrium heat treatment. When the composition of an alloy placed it in a critical area of the 200" or 100°C isothermal section, a check chemical analysis was made on a sample taken from the alloy specimen as-heat-treated at the particular temperature. Standard chemical procedures of gravimetric analysis were used in the determination of magnesium and aluminum; lithium, potassium, and sodium were determined by flame photometer methods

Jan 1, 1956

By A. R. Troiano, E. A. Steigerwald, F. W. Schaller

The kinetics of crack propagation in a hydrogenated high-strength steel at subzero temperatures indicated that cracking progressed in a discontinuous fashion. The delayed failure process thus involves a series of crack initiations rather than the continuous growth of a single crack. The incubation time required for the initiation of delayed failure was controlled by the diffusion of hydrogen. The activation energy for the process was 9120 cal per g-alom. As the test temperature was lowered the incubation time constituted a greater percentage of the total tinze to fracture, and al -50°F the incubation and fracture times were essentially coincident resulting in instantaneous, catastroplzic fracture. A unique feature of hydrogen embrittlement is the delayed failure process in which the material fails under the action of a sustained load even though it is capable of supporting a higher load for a finite period of time.')' Delayed failure of steel and titanium is characterized by an incubation time, preceding the initiation of a crack in a highly localized region, and the subsequent growth of the crack to ultimate failure.3-5 The kinetics of crack growth in hydro-genated high-strength steels have been studied through the use of resistance measurements and have an important bearing on the mechanism of delayed failure. Delayed failure is believed to be merely a facet of hydrogen embrittlement in which sufficient time is allowed during a test for hydrogen diffusion. The current theories employed to explain hydrogen em-brittlement can be grouped into two types. one6-8 explains the embrittlement on the basis of the pressure exerted by molecular hdrogen in lattice voids or defects while the other9-10 attributes the embrittlement to the influence of hydrogen in the lattice. The mechanism used to explain the nature of the crack kinetics in delayed failure is based on the stress-induced diffusion of hydrogen to the area of maximum triaxiality.3 When the hydrogen concentration in this region reaches a critical value, a crack is nucleated. This initial crack propagates instantaneously until stopped by the higher fracture stress of the adjacent material of lower hydrogen content. The continuation of cracking must then await the further diffusion of hydrogen to the new region of triaxiality near the base of the crack where another initiation will occur. From this mechanism it follows that crack propagation is nothing more or less than a series of initiations with limited fracture. The purpose of this investigation was to examine the kinetics of crack growth in an effort to determine whether or not the process was discontinuous. Studies of crack propagation were conducted at low temperatures to retard the diffusion of hydrogen which is presumed to be the rate controlling process in delayed failure. MATERIALS AND PROCEDURE Specimen Preparation—A commercial heat of air-craft quality SAE-AISI 4340 steel, designated as Heat G, was furnished by the Republic Steel Co. in the form of %-in. hot-rolled bars. The material had the following chemical analysis: Composition of 4340 Steel—G Heat C Mn Si Ni Cr Mo 0,395pct 0.82pct 0.29pct 1.76pct 0.85pct 0.25pct Notched tensile specimens with less than a 0.001 in. radius, Fig. 1, were used throughout the investigation. The specimens were heat treated to a 230,000 psi strength level according to the following sequence: a) Normalize bar stock at 1650°F for 1 hr, b) Stress relieve at 1200°F for 4 hr and furnace cool,

Jan 1, 1960

By J. B. Morrow

WITH numerous plans under consideration for coal classification, and with the advent of the Bituminous Coal Code, the intelligent sam-pling of coal has become increasingly important. To us it is rather significant that there have been very few fundamental studies of coal sampling in American technical literature since those of E. G. Bailey, which appeared in the Journal of Industrial and Engineering Chemistry in March, 1909. He covered the subject up to that time so thoroughly and in such an excellent manner that perhaps many other later students have felt that they could add very little to his findings. The recent studies of the British Engineering Standards Association have indicated the possibility of a somewhat different interpretation of Bailey's results, permitting the taking of smaller samples, and perhaps it will now be helpful to reopen this question. C. W. H. Holmes, in an informative series of articles on coal sampling recently published in Colliery Engineering, makes two rather interesting statements, as follows: It is scarcely surprising to find a lack of interest and knowledge regarding the sampling of coal not only in the mining industry itself but also among consumers of industrial fuel: at its best coal sampling is a dirty business, regarded as a nuisance and an expense by the commercial man, and usually as a nuisance and nothing else by the chemist. The writer can conceive only two classes of people who have never experienced any difficulty in obtaining representative samples of coal from wagons; those who have never tried to, and those who have never had the necessity or desire to check the accuracy of their work. The primary purpose of this paper is to present some tabulated data of the more significant results of a sampling investigation undertaken during the last four years to obtain certain fundamental data on the variables connected with coal sampling and to point out that often assumptions have been made that are not in accordance with the facts. One of the standard sampling methods states:

Jan 1, 1935

By Charles D. Borror, George K. Foster

The Jeffrey mine of the Canadian Johns-Manville Co., Limited, is in the town of Asbestos, situated approximately 100 miles northeast of Montreal and about the same distance southwest of Quebec, in Richmond County, Quebec. Mining operations were started in 1881 on outcrops on a hill, as a side-hill cut, followed by a second and third cut. This development was the forerunner of the present large open-pit operations, the mine now ranking as the largest open-pit asbestos mine in the world. Operations were first carried on by hand, then by horsepower and later by stem cableways. By 1924 the derrick spans, 2000 ft. or more long, became unwieldy. To overcome this, and also to eliminate hand labor as much as possible, steam shovels and railroad haulage were introduced. The steam shovels were replaced in 1928 by larger electric shovels of the full-revolving type. The Ore Body The ore body is a serpentinized peri-dotite rock mass. The chrysotile fibers form a network of veins throughout, varying from microscopic width to two or more inches measured across the veins (Fig. I). These veins may be continuous for a few or many feet; they may increase or decrease in width within a few feet. The veins in which the fibers occur per- pendicular to the veins are known as cross fiber. Those in which the fibers lay parallel to the veins are known as slip fiber. The cross fibers are of better quality, and more in demand. The majority of the fiber

Jan 1, 1948

By George K. Foster, Charles D. Borror

The Jeffrey mine of the Canadian Johns-Manville Co., Limited, is in the town of Asbestos, situated approximately 100 miles northeast of Montreal and about the same distance southwest of Quebec, in Richmond County, Quebec. Mining operations were started in 1881 on outcrops on a hill, as a side-hill cut, followed by a second and third cut. This development was the forerunner of the present large open-pit operations, the mine now ranking as the largest open-pit asbestos mine in the world. Operations were first carried on by hand, then by horsepower and later by stem cableways. By 1924 the derrick spans, 2000 ft. or more long, became unwieldy. To overcome this, and also to eliminate hand labor as much as possible, steam shovels and railroad haulage were introduced. The steam shovels were replaced in 1928 by larger electric shovels of the full-revolving type. The Ore Body The ore body is a serpentinized peri-dotite rock mass. The chrysotile fibers form a network of veins throughout, varying from microscopic width to two or more inches measured across the veins (Fig. I). These veins may be continuous for a few or many feet; they may increase or decrease in width within a few feet. The veins in which the fibers occur per- pendicular to the veins are known as cross fiber. Those in which the fibers lay parallel to the veins are known as slip fiber. The cross fibers are of better quality, and more in demand. The majority of the fiber

Jan 1, 1948

By W. A. McCurdy, Joseph W. Leonard, William F. Lawrence

INTRODUCTION Utilization from the Point of View of the Preparation Engineer The primary interest of the coal preparation engineer is in process design, operation, and maintenance to produce an acceptable product that can be sold at the greatest possible profit. Because of emphasis upon these interests, attention to other potential values of coal is sometimes neglected. The intent of this chapter is to alert the preparation engineer to the utilization possibilities of the product as well as the tributary coal flow moving through a modern coal preparation plant. The basis for any unrealized potential derives directly from the coal seam itself. Most coal seams consist of coal bands and benches sandwiched together in layers that differ visually from each other in physical structure and luster. Randomly selected physical and chemical ranges determined from layers of coal in a single seam can easily differ by as much as 30 Hardgrove grindability indices, 0.30 of a specific gravity point, 20 percentage points of ash, 6 percentage points of dry volatile matter, and 10 percentage points of total su1fur.l Similar wide variations exist for calorific value, seam moisture content, and, undoubtedly, for any other conceivable coal test parameter that might be used for comparative purposes. These observations all point to the long-established fact that coal is not homogeneous, as conventional analytical methods might tend to indicate, but is instead a highly heterogeneous substance.

Jan 1, 1979

By W. J. Helfrich, R. A. Dodd

Binary aluminum solid-solution alloys containing various amounts of silver, magnesium, and zinc were prepared by careful directional solidification, and the hydrostatic and X-ray densities were compared. With the exception of the Al(Ag) alloys, the X-ray densities were consistently greater than the hydrostatic measurements, in agreement with earlier observations by Ellwood. In contrast to Ell-wood's interpretation in terms of vacant lattice sites associated with Brillouin zone effects, a tentative explanation based on the existence of solidification microshrinkage was favored. This hypothesis was confirmed by an examination of Al(Zn) alloys prepared by vapor diffusion of zinc into aluminum. The hydrostatic and X-ray densities were now in very close agreement, and it was concluded that the filling of Brillouin zones in aluminum solid-solution alloys does not necessarily result in the formation of defect structures containing an excess of vacant lattice sites. ThE existence of defect structures of the vacancy type in alloys in which the excess vacancies have an electronic rather than a thermal or mechanical, and so forth, origin is well recognized. Examples of incomplete lattices of this type are to be found in the Ni-Al,1-3 Fe-Ni-A1,4 c~-Ni-Al,5 Fe-Cu-Al,= and Co-A17 systems. These defect structures are of a special kind in that the intermediate phases possess an ordered atomic arrangement or superlattice, and in some instances the vacancy concentration may be unusually large, e.g., at 45.25 at. pet Ni in NiA1, approximately 8.8 pet of the lattice sites are unoccupied. Ellwood8-10 has reported similar defect structures in the aluminum solid solution alloys of the Al-Zn and A1-Mg systems and in alloys of the Au-Ni system." In Al(Zn) the (apparent) vacancy concentration rose, somewhat irregularly, to a maximum of about 2 pet vacant sites at 25 at. pet Zn, while in Al(Mg) the (apparent) vacancy concentration increased continuously to 1.7 pet at 15 at. pet Mg. An explanation in terms of Brillouin zone overlap was attempted, although Pearson12 has pointed out the difficulty of reconciling the observations with zone theory. However, the possibility of the effect being caused by the Fermi surface just touching a plane of energy discontinuity inside a prominent Brillouin zone has, in general, been accepted. In fact, Massal-ski13 has interpreted Ellwood's8 observations as confirmation of Leigh's14 theoretically predicted zone overlap occurring at approximately 2.67 electrons per atom. Unfortunately, Massalski was apparently unaware that Ellwood9 had revised his earlier results considerably, and the revised data did not confirm Leigh's analysis. Ellwood's clata were reexamined by the present authors who noted a possible correlation between the percentage defects as a function of alloy composition and the temperature interval of solidification measured from the respective equilibrium diagrams. This suggested an explanation in terms of shrinkage porosity rather than vacant lattice sites, and pointed to the desirability of reexamining appropriate alloy systems using: both Ellwood's method of specimen preparation (casting followed by wrought fabrication) and alternativ'e methods, i.e., diffusion, which might be expected to minimize, or even completely obviate, microporosity. ALLOY PREPARATION 1) Cast Allolys and Aluminum Single Crystals. Al(Ag), Al(Mg;l, and Al(Zn) alloys of various compositions up to 20 at. pet silver, 13.5 at. pet mg, and 30 at. pet Zn were prepared by melting under helium and casting into graphite molds. In the first two systems, the maximum alloying addition was quite close to the limit of solid solubility, but the possibility of transformation to a' during quenching somewhat restricted the suitable Al(Zn) composition range. The alloys were prepared from high-purity aluminum, a lot analysis showing 0.002 wt pet Cu, 0.002 wt pet Fe, and 99.996 wt pet A1 by difference. The silver, magnesium, and zinc were of 99.99+, 99.98+, and 99.998 wt pet respectively. Each composition was analyzed chemically. The as-cast ingots measured 7/16 in. diam and 5 in. length. One in. was removed from the top of the ingot, and the bottom 3 in. was machined to 0.275 in. diam; a point was also machined on the smaller diameter end. The remainder of the original ingot served as a top riser during subsequent remelting and controlled solidification. The machined ingots were now remelted using a Bridgman soft-mold technique to ensure directional solidification and, therefore, a minimum of micro-shrinkage. Alumina powder was used as mold material contained in an alundum thimble, and this crucible was placed in a helium-filled Vycor tube. The assembly was lowered through a suitable temperature gradient at approximately 0.5 in. min-l, and the risered portion of the casting was subsequently removed by sawing.

Jan 1, 1962

By C. G. Rhodes, D. Kramer

High-field critical transport current density (J) measurements at 4.2 °K as a Junction of applied magnetic field (H) were made on samples of cold-rolled and annealed columbium with H parallel to J. Microscopic examination of the samples revealed a well-defined planar fiber structure produced by the cold rolling. J was found to he lower when fibers are parallel to the direction of magnetic field penetration than when they are perpendicular. This effect may he a consequence of the interaction of flux movement with fiber boundaries. THE severe changes in microstructure brought about by cold working superconductors leads to profound changes in their superconducting behavior. In particular, the ability of a superconductor to carry a transport current with zero resistance (the maximum value of this current density will be called "J" in the presence of large external magnetic fields (to be referred to as "H") is greatly influenced by the microstructure. In the case of columbium, LeBlanc and Little1 and Autler et a1.2 have observed an increase in J due to cold work. LeBlanc and Little also observed an anisotropy in J in cold-rolled columbium strips, which Hake et al.3-6 have shown to depend upon the angle between H (H ? J) and the rolling plane. An increase in J due to cold work has been found in a variety of high-field superconducting alloys3'4'7-9 as has the anisotropy effect.10 First explanations of why cold work raised J invoked the idea that dislocations carried the high-field supercurrents,8,11 since cold working drastically increases the dislocation density and presumably the number of supercurrent paths. However, recent ideas on the nature of high-field superconductivity together with new experimental evidence reveal that the bulk of certain superconductors can remain superconducting in high fields while carrying high transport currents. These later developments have been discussed by Berlin-court and Hake12 and a comprehensive review has been prepared by Berlincourt.13 According to the ideas of Gorter14 and Anderson,15 one would expect that the influence of microstructure on high-field supercurrent density will depend on tine interaction between microstructure and penetrating flux and on the direction of the Lorentz

Jan 1, 1965

By R. H. Hiltz, R. W. Douglass

Large-grain specimens of iodide titanium prepared metal-lographically were stain etched using the technique of New York University as modified by Watertown Arsenal Laboratories. Orientations of grains showing an abnormal response to stain etching were determined by back-reflection X-ray techniques. X-ray results showed that a-titanium grains, oriented such that their basal planes were parallel to the polished surface, have a slower reactivity to stain etching than any other orientation. Grains oriented such that their basal planes made small angles with the polished surface exhibited reaction rates between that of the true basal orientation and the normal rate. As the angle with the surface increases the reactivity increases up to a maximum angle of 14 deg. Basal planes making an angle with the surface of greater than 14 deg show normal reactivity to stain etching. These data, plus work on polycrystalline specimens, indicate that the oxidation rate of titanium might be reduced by correct alignment of crystal planes. ThE earliest observed phenomenon in the micrography of titanium was the occurrence of a grains which exhibited no birefringency. Even though a titanium possesses a hexagonal-close-packed structure and should be optically anisotropic, it can appear optically isotropic, when the crystal is so oriented that its intersection with the polished surface is perpendicular to the axis of symmetry. During the develoment of color staining techniques for titanium: it was noted that the a phase did not stain uniformly. Staining of specimens of commercially pure titanium resulted in a micro-structure of blue-colored grains, among which were randomly oriented a few grains exhibiting colors between the initial yellow and the final blue color. Under polarized light, these off-colored grains appeared to be optically isotropic. More intense study with polarized light, however, showed only the yellow grains to be isotropic. The intermediate colored grains exhibited weak birefringency, which at first glance is not detectable due to the strong birefringency of the surrounding structure. Aminoff2 and Straumanis3 have previously shown that in zinc the basal orientation is less reactive than other orientations. Leidheiser4 showed the same thing to be true for the hexagonal-close -packed configuration of cobalt. Thus, it would appear that the basal-plane orientation is responsible for the abnormality in stained titanium. Later work by Leidheiser5 on cobalt has shown that other planes besides the basal plane exhibited reaction rates slower than the normal rate. Reported planes were the (100), the (1011) and several planes making small angles with the basal plane. The last observance appears not to be due to the reactivity of the reported plane but due to the reactivity of the basal plane which is very close to being parallel to the surface. There are, then, two possible explanations for the range of colors observed in stain-etched a titanium. Since extensive research on the effect of orientation on surface reaction has failed to provide any definite trend, these two explanations are not adequate in themselves. Planes showing the retarded reactivity differ not only for different crystal structures but for metals of the same crystal structure and even for different reactions of the same metal. Tragert,6 Leidheiser,7 Tammann,6 and wagner9 have shown copper to exhibit retarded reactivity on the (111) plane. However, Leidheiser10 has shown that under other conditions the retarded reactivity of copper is associated with the (100)

Jan 1, 1960

By Cyril Stanley Smith

The method of thermal analysis, so important in the development of metallographie science, has of recent years been falling into disuse owing to the development of other physical methods which give result's easier of interpretation and which can be used for the study of either equilibrium or transitional conditions because they do not require a continuously changing temperature. Nevertheless thermal analysis remains useful in the study of reactions that take place rapidly, and the simplicity of the experimental technique and the general availability of the apparatus involved are point's in its favor. Theoretically, thermal analysis is capable of giving specific and latent hat measurements and therefore should permit the study of reactions on a more fundamental basis than any other method. It is, however,difficult or impossible to obtain quantitative heat measurements from cooling curves obtained in the usual way. Even if the furnace containing the sample is cooled or heated at a linear rate, or if a gradient furnaec is employed to maintain a constant rate over a large range of temperature, the heat flow from or to the specimen depends on its previous history, for the difference of temperature between the specimen and its surroundings varies. The emissivity of the specimen surface, moreover, is unlikely to be constant. The able mathematical analysis by Russrll,1 although it prevent,s misinterpretat,ion of data, has an effect rather the reverse of that intended, and leaves the reader doubtful of the possibility of ever obtaining quantitative results from thermal curves. Nothing can be done to apply thermal analysis t'o the study of equilibrium conditions of reactions that arc not completed at rates of temperature change above about 1° C;. per minute, and this unfortunatetly excludes most solid transformations in alloys.† For the determination of liquidus

Jan 1, 1940

By Cyril Stanley Smith

The method of thermal analysis, so important in the development of metallographie science, has of recent years been falling into disuse owing to the development of other physical methods which give result's easier of interpretation and which can be used for the study of either equilibrium or transitional conditions because they do not require a continuously changing temperature. Nevertheless thermal analysis remains useful in the study of reactions that take place rapidly, and the simplicity of the experimental technique and the general availability of the apparatus involved are point's in its favor. Theoretically, thermal analysis is capable of giving specific and latent hat measurements and therefore should permit the study of reactions on a more fundamental basis than any other method. It is, however,difficult or impossible to obtain quantitative heat measurements from cooling curves obtained in the usual way. Even if the furnace containing the sample is cooled or heated at a linear rate, or if a gradient furnaec is employed to maintain a constant rate over a large range of temperature, the heat flow from or to the specimen depends on its previous history, for the difference of temperature between the specimen and its surroundings varies. The emissivity of the specimen surface, moreover, is unlikely to be constant. The able mathematical analysis by Russrll,1 although it prevent,s misinterpretat,ion of data, has an effect rather the reverse of that intended, and leaves the reader doubtful of the possibility of ever obtaining quantitative results from thermal curves. Nothing can be done to apply thermal analysis t'o the study of equilibrium conditions of reactions that arc not completed at rates of temperature change above about 1° C;. per minute, and this unfortunatetly excludes most solid transformations in alloys.† For the determination of liquidus

Jan 1, 1940

By E. S. Davenport

IT is indeed an honor and a responsibility to have been selected to present the thirty-fourth in this series of Henry Marion Howe lectures, established to perpetuate the memory of a great teacher and one of America's outstanding scientists. Previous Howe lecturers have established high standards for this annual AIME event. It has been my good fortune to have enjoyed close association with five of these former lecturers; namely, Bain, Grossmann, Johnston, Sosman, and Vilella, all of whom have been prominently identified with the research activities of the organization with which I am connected. Some years ago I had an opportunity to examine a letter written by Professor Howe in 1904. This document was particularly interesting to me since I never had the privilege of personal acquaintance with Professor Howe and do not recall even having seen him during his long and active career. In view of the fact that the letter dealt, to some extent, with matters related to the subject of today's lecture, I would like to quote briefly from it. The letter is datelined, "Bad Kissingen, June 11, 1904." The salutation reads, "Dear Bradley," which suggests that it was probably addressed to Bradley Stoughton, who, I believe, was working with Howe at Columbia University at that time. The letter reads, in part, as follows: "Austenite and Martensite. I have not examined what Osmond says in his new book. His former remarks about austenite I found very confusing, indeed unintelligible. I think we can reconcile matters well enough for the present by assuming that martensite is a transition step between austenite at one end and ferrite and cementite at the other. Above critical range for steel of 0 to 1.80 carbon, austenite is normal state; below Ar1, ferrite and cementite are normal." The letter then continues with a discussion of Osmond's ideas on metallographic nomenclature, particularly his use of the terms martensite, troostite, and sorbite, including the following pointed comment: "For common purposes it seems to me unwise to drag them in, and much simpler to confine ourselves to the end stages Austenite Ferrite plus Cementite Osmond does not really know his own mind— or does not clarify his ideas to others—as to nomenclature." Thus we see that, as far back as 1904, the transformation of austenite, and the products of that

Jan 1, 1958

By F. M. Simonds, E. Z. Burns

The Rawley property is located in the Kerber Creek mining-district, Saguache county, Colorado, at an elevation of 10,600 ft. (See sketch-map, Fig. 1.) Ore was found in this vicinity as early as 1880, and claims covering a large area were located and in many instances patented. The ores, however, being of comparatively low grade, and the nearest railway station, Villa Grove, being some 20 miles away, it is extremely doubtful whether any considerable amount of ore was ever handled at a profit. It is safe to say that several hundred thousand dollars were spent (a large part in building mills) previous to 1902-03. About that time a very capable promoter gathered together a group of these claims and interested some New York people, who had had no previous mining experience, in the purchase of these claims. Following the organization of a company, this promoter became General Manager. As often happens under such conditions, the first step was to erect a mill to treat 100 tons per day. It may not be fair to this enterprise to say that the failure which followed might have been foretold, simply on general principles, but this much is certain—the water supply fluctuates in the course of a season through a wide range and for a considerable portion of the year was inadequate to run this mill at capacity. Further, it is currently reported that some of the mill foundations were placed on ice. However true this statement may be, it is a fact that, when first inspected by us, many of the belts in the mill were held on'their pulleys by means of idlers. A shut-down followed, with a material re-adjustment of interests, at which time we became consulting engineers for the company.

Jan 1, 1914

By D. J. Reed

Concord coal mine near Bessemer, Ala., built, owned, and operated by Tennessee Coal & Iron Div., U. S. Steel Corp., produces only a metallurgical grade for use as coke in blast furnaces of the division at the Fairfield and Ensley works. Capacity of the operation is approximately 800 tph, half of which is delivered to the coke and coal chemical plant at Fairfield after beneficiation to metallurgical grade coal. The remaining portion of the mine run is rock and refuse removed during preparation. Concord mine coal is hoisted to the surface coal preparation plant by an underground slope conveyor. The slope conveyor is 2449 ft long and has a lift of 729 ft. At time of installation the Concord mine slope conveyor was the largest single conveyor unit ever made with respect to belt horsepower and total lift. After several years it became necessary to determine the cause of slope conveyor cover wear.

Nov 1, 1956

By B. C. Allen, W. D. Kingery

Surface tension and its temperature dependence have been determined for pure liquid Fe, Cu, Co, Ni, and Sn and for Fe-C, Co-C, and Ni-C alloys. The temperature coefficient of surface tension is negative for all these liquids. The surface tension and wetting behavior of tin and tin-titanium alloys on A120,, Si,N,, MoSi,, and Sic, as well as the behavior of titanium-containing nickel alloys on A1 20, have been determined over a wide temperature range. For all the solids investigated titanium additims markedly lower the contact angle. Some limits for the solid-surface energies have been calculated from liquid surface tension and wetting behavior. SURFACE tension and interface energy are important variables in a number of metallurgical and ceramic phenomena, and have been discussed at some length in connection with determining micro-structure of polyphase systems,' solid-state sintering,' thermal etching of grain boundaries, heats of solution and fine powders,'1 grain-growth phenomena,' the mechanical behavior of fine foils and fibers, nucleation, soldering and brazing,' and other phenomenz of academic or practical interest However, until recently few quantitative data have been available for high-temperature systems. Among available data are some indicating positive temperature coefficients for the surface tension of liquid copper,*,11,'2 cast iron,l3 and iron-carbon14 alloys. Although carbon was found to be not surface active in iron at 1570" some preliminary studies had indicated the possibility of a positive temperature coefficient for the eutectic composition at lower temperatures.16 One part of the present study has been largely concerned with determining the temperature coefficient of surface tension for several metals at elevated temperatures, In addition to surface-tension studies, the wetting behavior of alloys containing titanium has been investigated over a wide temperature range. Previous measurements indicated that titanium was selectively adsorbed from nickel at a liquid nickel-solid alumina interface,17 and the use of titanium hydride or titanium-alloy techniques for metal-ceramic soldering is well known. In the present study, previous data have been extended to new alloy systems, and measurements have been carried out with other oxidation-resistant ceramics. EXPERIMENTAL The sessile-drop method was employed to measure liquid surface tension and contact angle between liquid and solid, utilizing apparatus and techniques which have been described previously.'g The shape of a sessile drop depends on equilibrium between forces of surface tension tending to form a spherical surface of minimum area and forces of gravity tending to flatten the drop. Typical sessile drops are shown in Fig. 1. From precise measurements of maximum drop diameter and drop height the surface tension and drop volume were calculated. Four solid materials were employed as supporting plaques for the liquid-metal drops. Aluminum oxide (99.9 pct, J, T. Baker, reagent grade) was pressed and sintered at 1800°C. Molybdenum-disilicide powder (99.0 pct, Electro Metallurgical Co.) was pressed and sintered at 1650°C. Plaques were cut from silicon carbide (99.4 pct, hot-pressed at Alfred University) and silicon nitride (95.1 pct, with Al, Fe, 0 as major impurities, Norton Co.) rods. All plaques were polished, cleaned, and dried prior to use. A number of metals and alloys were employed. Chemical analyses of vacuum-melted ingots of iron, nickel, cobalt (National Research Corp.), commercial nickel-base alloys, electrolytic copper (International Smelting and Refining Co.), and tin (Mal-linckrodt Chemical Works) are given in Table I. Alloys were prepared in the laboratory by vacuum melting the base metal with either titanium hydride (Metal Hydrides, Xnc.) or spectroscopic-grade carbon (National Carbon Corp.). Nickel-titanium alloys contained between 0.001 and 0.005 pct oxygen and the ferromagnetic metal-carbon alloys contained 0.001 pct. Cylindrical metal specimens (1 to 2.5 g) were machined and bevelled at the bottom to insure a uniform advancing contact angle on melting. Before use the samples were acid-etched, cleaned with acetone, and rinsed in petrol ether.

Jan 1, 1960

By T. G. Nilan

Steels containing 0.4 and 0.8 pet C have been transformed isothermally at pressures up to 34 kbuv. Decomposilion mechanisms are so intimately related to phase equilibvia that, as the equilibria shift under high pressure, the microstruclures of the decomposition producls change, maintaining at pressure the same correspondence between a given phase equilibrium and a given microstructure as a1 1 atm. A bainitic unicvo-structure occurs in these steels at high pressure that IS observed only at 1 aim abole 1.4 pct C. This strrrcl111,e 1s ruliorzalized in terms of the effect of pressure on the transformation to lower bainite. The pressuve depetlderlce of the kinetics of pearlile formation is descrihed by an absolute rule theory amalysis. The activation volume for the transformation is 7 cu cm per mlole, which is indicative of a phase-interface transformation-rate cotntrol mechanism. This fortmulation, when expressed in terms of known solule effects on the energelics of tvansformation, gives promise of explaining the effects of alloying elemenls on hnrden-abilily, particularly that of 'coball. KINETIC processes in solids are functions of the primary thermodynamic variables of state: composition, temperature, and pressure. Until the development of high-pressure techniques' that permitted the generation of sustained high pressure at high temperatures, metallurgical studies of such reactions were largely limited to isobaric conditions at atmospheric pressure. The data so obtained, and theoretical deductions based on these data, were necessarily incomplete For the particular case of austenite decomposition, a knowledge of the phenomenology of the reaction in terms of all the state variables should lead to a clarification of the process. This deeper understanding should facilitate a decision between conflicting theories that have been proposed to rationalize these phe- nomena. An analysis, derived from an understanding of the transformation mechanisms, may aid in the optimization of alloy steel development. The first studies of the effect of pressure on transformations in steel were made by Kulin et al. in 1952.' In a study of the influence of applied stress on mar-tensite formation in a 30 pct Ni steel, they found that the martensite start (M,) was depressed 8°C per kbar* by hydrostatic pressure. Jellinghaus and Friedewold3 were apparently the first to investigate the effect of pressure on isothermal transformations above the Ms. They found that the bainite transformation rate in a 1.2 pct C, 3.8 pct Mn steel was reduced by a factor of 3 by a hydrostatic pressure of 4 kbar. In both of these investigations,2,3 the M, of the steels studied was below room temperature. Austenitizing and quenching were done at atmospheric pressure, followed by the decomposition of the metastable austenite under pressure. The maximum temperature at pressure in the bainite study3 was 350°C. Until the advent of the present high-pressure devices, it was not possible to conduct isobaric high-pressure heat treatments from austenitizing through isothermal decomposition and quenching. The exploitation of high pressure as a variable in metallurgical studies was greatly advanced by the apparatus and techniques developed by Hall4 and co-workers. Utilizing these techniques, Radcliffe et a1.5 and Hilliard6 etermined the pressure dependence of phase equilibria in the Fe-C system. Hilliard and cahn7 examined the pearlite transformation rate in an AISI 1080 steel and also in a high-purity 0.92 C Fe-C alloy at 1 atm and at 34 kbar and found a 700-fold reduction in rate at pressure in the 1080 steel but only a fivefold reduction in the high-purity alloy. In agreement with the shift of phase equilibria under pressure, the microstructures were hypereutectoid at 34 kbar pressure, whereas they are eutectoid at 1 atm. Determination of the effect of pressure on carbon diffu-

Jan 1, 1968

By J. R. Hunter

Current trends in mining practices within the United Kingdom, with particular reference to longwall retreating systems in thick and steeply pitched coal seams at depth, are explained. Various successful mining layouts are considered with their associated machinery and operation, together with the future trends in mining practices to obtain higher outputs. Environmental difficulties are tabled and discussed, including strata control, methane emmision, and dust prevention, together with some modified systems and techniques to overcome them. The problems associated with developing and maintaining a continuance of longwall panels are outlined. The constraints on technical designs and output achievement imposed by noncommercial factors are also considered.

Jan 1, 1978

By P. G. Beckett

THE problem of handling the large quantities of water encountered in the Old Dominion mine presents many features of interest. In the present paper are discussed the probable sources of water, the pumping equipment, the increased flow into the mine in the early part of 1915, culminating in the flooding of the 18th and 16th levels in March of that year, and the difficulties that were met with during the high-water period. I. PRELIMINARY The Old Dominion mine, situated 1 mile north of the town of Globe, Ariz., has long been one of the prominent copper producers of the State, and until the opening up of the copper schist deposits in the neighboring mines of Miami, was responsible for the greater part of the copper output from the Globe district. As the gradual exhaustion of its orebodies near the surface led to the downward development of the mine, more water was encountered in the western portions directly underlying the dacite formation until the drainage problem became a serious factor in the operation of the mine and in the economical extraction of the ore. A heavy inrush of water on the 10th level of the mine in 1906, preceded by still earlier water difficulties, rendered imperative the immediate installation of a pumping equipment capable of handling large flows of water. While the Old Dominion has been recognized as a wet mine since its early clays and one in which the complete control of the water situation was of paramount importance in the development of the lower levels, it is chiefly in the last nine years, since the installation of the increased pumping equipment, that the mine has developed and handled large quantities of water.

Jan 4, 1916

By J. A. Norden

MUCH has been written concerning the hoisting equipment of various mines -throughout the country, but most of the literature on the subject, if not all, describes equipment of extraordinary capacity and the small and medium-sized outfits have been neglected. The hoisting equipment here described is capable 'of handling about 1200 tons per day. It has not been worked, to capacity, but 600 to 700 tons, together with men and materials, have been handled in two shifts without any great effort. Only one shaft extends from the surface to the lowest levels of the mine; see Fig. 1. It is composed of three compartments, two of which are used for hoisting and the third for water, air, and electrical lines, and for sinking purposes. In 1909, this shaft was raised from the 1000-ft. (304-m.) level to the 700-ft. There a station was cut and an air hoist installed. At this time all mining operations were confined to the upper levels of the mine; that is; above the 700-ft. The. ore was-dropped to this level through chutes from the 300-, 400-, 500-, and 600-ft. levels and then lowered in cars on cages to the 1000-ft., which is the main haulage adit, the mill and railroad bins being about 3000 ft. from the shaft. Orebodies were, in due time, developed on the 1000-ft. level and below. Therefore, in 1913, the shaft was sunk to the 1150-ft. level and thereafter sinking was continued at regular intervals until the 1500-ft. level was reached. But, hoisting from the 1300-ft. level was a difficult, and slow process with the antiquated air hoist, so, in 1916, it was derided to raise the shaft to the surface and install a modern, electrically operated hoist. This was completed early in 1917 and the hoist was in operation in March of that year.

Jan 8, 1920

By M. Murakami, Y. Murakami, O. Kawano

The formation and growth of Guinier-Preston zones in Al-Zn alloys containing 4.4, 6.8, 9.7, and 12.4 at. pct zn have been studied by the X-ray small-angle scattering method. Particular attention was paid to the effects of small amounts of third elements silver, silicon, and magnesium on the formation and growth of G.P. zones. It was noticed that an appreciable number of G.P. zones were formed during the course of rapid cooling and that the size, volume fraction, and number of these G.P. zones were influenced by the existence of the third elements. During subsequent aging it was also found that the addition of both silver and silicon lowered the temperature for the growth of G.P. zones, whereas the addition of magnesium raised it. These results were explained in terms of the mutual interactions among zinc atoms, vacancies, and the third elements. A number of studies on the formation and growth of Guinier-Preston zones in Al-Zn alloys have been reported.1-4 Panseri and Federighii have found that the initial stages of zone growth take place at temperatures as low as around -100°C. For investigation of the mechanism of the initial stages of zone growth, growth studies must be carried out at low temperatures. In order to investigate the possibility of the formation of G.P. zones by the nucleation mechanism or the spinodal decomposition during quenching which was reported by Rundman and Hilliard,5 the examination of the as-quenched structure must be performed. In this paper the investigation of the early stages of the formation and growth were determined by means of the X-ray small-angle scattering method. With this technique, change of X-ray scattering intensities was measured while quenched specimens were heated slowly from liquid-nitrogen temperature to room temperature. At as-quenched state and after heated to room temperature, investigation of zone size, volume fraction, and zone number per unit volume was carried out. Measurements on these specimens yielded information on the early stages of zone formation and growth. Measurements were made also on specimens quenched to and aged at room temperature. From these measurements the previously reported model6 for the later stages of growth is confirmed; namely, the larger zones grow at the expense of smaller ones. Three elements, silver, silicon, and magnesium, were chosen as the third elements for the following reasons: Silver. In the binary A1-Ag alloy the spherical disordered 77' zones were observed immediately after quenching.7 Therefore, in the Al-Zn-Ag alloys, it is suggested that silver atoms might induce cluster formation during quenching. Also, since the migration energy of the zinc atoms was found to be raised by the addition of silver atoms,' silver atoms may have a great effect of the zinc diffusion, especially during low-temperature agings. Silicon. The effects of the addition of silicon atoms were found to be marked, especially at low-tempera-ture aging. In the binary Zn-Si system, no mutual solid solubilities between silicon and zinc9 and no in-termetallic compounds10 are reported to exist. Shashkov and Buynov11 investigated the behavior of silicon atoms in Al-Zn alloys and showed that silicon was not in the G.P. zones. The interaction between silicon atoms and vacancies is strong enough to increase the quenched-in vacancy concentration.* Magnesium. Magnesium atoms are reported to trap quenched-in vacancies and after much longer aging times these trapped vacancies will become free and act as diffusion carriers.13 Therefore at intermediate aging times, the diffusion of zinc atoms in Al-Zn-Mg alloys will be slower than in the binary Al-Zn alloys, whereas at longer times zinc diffusion will become faster. EXPERIMENTAL PROCEDURE The alloys used in this investigation had compositions of 4.4, 6.8, 9.7, and 12.4 at. pct Zn with or without 0.1 and 0.5 at. pct Ag, Si, or Mg. The alloys were prepared from high-purity aluminum, zinc, silver, silicon, and magnesium, with each metal having a purity better than 99.99 pct. The analyzed composition of the specimens is given in Table I. The measurements of the X-ray small-angle scattering were carried out with foils of 0.20 mm thick. The change of the scattering intensity was always measured at the fixed scattering angle of 20 = 2/3 deg. This angle exists nearly on the position of the intensity maximum. The value of the interparticle interference function14 which has large effect in this range of angles may not change abruptly in the case of the spherical shape of small zones. Therefore, from the above considerations, it is concluded that an increase of the intensity measured at this constant angle corresponds to an increase of the average radius and volume fraction of G.P. zones. The specimens were homogenized at 500°, 450°, and 300°C for 1 hr in an air furnace. For the study of the formation and growth at low temperatures, the foil

Jan 1, 1970